LG Electronics BH6730S, S63T1-W, S63S2-S, S63S2-C User Manual

OWNER’S MANUAL

SMART 3D Blu-ray™ HOME THEATER SYSTEM

Please read this manual carefully before operating your set and retain it for future reference.

BH6730S (BH6730S, S63S2-S/ C, S63T1-W)

www.lg.com

1 GettingStarted

2 Getting Started

Safety Information

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle

is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s

enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing)

instructions in the literature accompanying the product.

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

WARNING: Do not install this equipment in a confined space such as a book case or similar unit.

CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings shall be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless

proper ventilation is provided or the manufacturer’s instruction has been adhered to.

CAUTION : CLASS 1M VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS

Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure.

CAUTION concerning the Power Cord

Most appliances recommend they be placed upon a dedicated circuit;

That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner’s manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized service center. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and

the point where the cord exits the appliance. To disconnect power from the mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible.

This device is equipped with a portable battery or accumulator.

Safety way to remove the battery or the battery from the equipment: Remove the old battery or battery pack, follow the steps in reverse order than the assembly. To prevent

contamination of the environment and bring on possible threat to human and animal health, the old battery or the battery put it in the appropriate container at designated collection points. Do

not dispose of batteries or battery together with other waste. It is recommended that you use local, free reimbursement systems batteries and accumulators. The battery should not be exposed to excessive heat such as sunshine, fire or the like.

Getting Started	3

CAUTION: The apparatus shall not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, shall be placed on the apparatus.

FCC Compliance Statement

This device complies with part 15 of the FCC rules.

Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2)This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

yy Reorient or relocate the receiving antenna.

yy Increase the separation between the equipment and receiver.

yy Connect the equipment into an outlet on a circuit different from that to

yy which the receiver is connected.

yy Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment

FCC RF Radiation Exposure Statement : This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC Radio Frequency Interference Requirements

This device is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range. FCC requires this product to be used indoors for the frequency range 5.15 to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device. This device cannot be co-located with any other transmitter.

CAUTION: Regulations of the FCC and FAA prohibit airborne operation of radio-frequency wireless devices because their signals could interfere with critical aircraft instruments.

Responsible Party :

LG Electronics USA, Inc. 1000 Sylvan Avenue Englewood Cliffs, NJ 07632

TEL. : [phone]

1 GettingStarted

1 GettingStarted

4 Getting Started

Notes on copyrights

yy Because AACS (Advanced Access Content

System) is approved as content protection system for Blu-ray Disc format, similar to use of CSS (Content Scramble System) for DVD format, certain restrictions are imposed on playback, analog signal output, etc., of AACS protected content. The operation of this product and restrictions on this product may vary depending on your time of purchase as those restrictions may be adopted and/or changed by AACS after the production of this product.

yy Furthermore, BD-ROM Mark and BD+ are additionally used as content protection systems for Blu-ray Disc format, which imposes certain restrictions including playback restrictions for BD-ROM Mark and/or BD+ protected content. To obtain additional information on AACS, BD-ROM Mark, BD+, or this product, please contact an authorized Customer Service Center.

yy Many BD-ROM/DVD discs are encoded with copy protection. Because of this, you should only connect your player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copy-protected discs.

yy This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Rovi Corporation, and is intended for home and other limited viewing uses only

unless otherwise authorized by Rovi Corporation. Reverse engineering or disassembly is prohibited.

yy Under the U.S. Copyright laws and Copyright laws of other countries, unauthorized recording, use, display, distribution, or revision of television programs, videotapes, BD-ROM discs, DVDs, CDs and other materials may subject you to civil and/ or criminal liability.

>>Caution

yy Watching a 3D content for a long period time may cause dizziness or tiredness.

yy It is not recommended to watch a movie in 3D mode for infirm, child and pregnant woman.

yy If you are experiencing headache, tiredness or dizziness while viewing content in 3D,

it is strongly recommended to stop the playback and rest until you feel normal.

Getting Started	5

IMPORTANT SAFETY INSTRUCTIONS

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/accessories specified by the manufacturer.

12.Use only with the cart, stand,

tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when

moving the cart/apparatus

combination to avoid injury from tip-over.

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

1 GettingStarted

6 Table of Contents

	Table of Contents		33		Sound Effect
			4		Operating
	1	Getting Started	34		Home Menu Display
			34		–  Using [HOME] menu
	2	Safety Information	34		–  Using the Smart Share
	8	Introduction	35		Playing the Linked Devices
	8	–  Playable discs and symbols used in	35		–  Playing a disc
		this manual	35		–  Playing Blu-ray 3D disc
	9	–  About the “7” symbol display	36		–  Playing a file on disc/USB device
	9	–  Regional code	37		–  Playing a file on a network server
	10	Remote Control	38		Using Home Network Server for PC
	11	Front Panel	38		–  Installing Nero MediaHome 4
	11	Rear Panel			Essentials
			38		–  Sharing files and folders
	2	Connecting	39		–  About Nero MediaHome 4 Essentials
			39		–  System requirements
	12	Positioning the System	40		General Playback
	13	Speaker Connection	40		–  Basic operations for video and audio
	13	–  Attaching the speakers to the player			content
	14	Connecting to Your TV	40		–  Basic operations for photo content
	15	–  What is SIMPLINK?	40		–  Using the disc menu
	15	–  ARC (Audio Return Channel) function	41		–  Resume playback
	16	–  Resolution setting	41		–  Last scene memory
	17	Antenna Connection	42		On-Screen Display
	17	Connections with External Device	42		–  To control video playback
	17	–  AUX connection	42		–  Displaying content information on-
	18	–  PORT. IN connection			screen
	18	–  OPTICAL IN connection	44		Advanced Playback
	19	Connecting to Your Home Network	44		–  Repeat playback
	19	–  Wired network connection	44		–  Repeating a specific portion
	19	–  Wired network setup	44		–  Playing from selected time
	21	–  Wireless network connection	45		–  Selecting a subtitle language
	21	–  Wireless network setup	45		–  Hearing a different audio
			45		–  Watching from a different angle
	3	System Setting	45		–  Changing the TV Aspect Ratio
			46		–  Changing Subtitle Code Page
	24	Initial Setup	46		–  Changing the Picture Mode
	25	Settings	46		–  Viewing content information
	25	–  Adjust the setup settings	47		–  Changing content list view
	26	–  [NETWORK] menu	47		–  Selecting a subtitle file
	27	–  [DISPLAY] menu	48		–  Listening to music during slide show
	28	–  [LANGUAGE] menu	48		–  Setting the [3D] option
	29	–  [AUDIO] menu	49		Advanced Features
	31	–  [LOCK] menu	49		–  Wi-Fi Direct™
	32	–  [OTHERS] menu	50		–  Enjoying BD-Live™

			Table of Contents 7
50	–  LG AV Remote	65	Network Software Update
50	–  Private Sound Mode	65	–  Network update notification
51	–  Viewing information from Gracenote	65	–  Software update
	Media Database	67	Additional Information
52	–  Audio CD recording	67	–  File requirement
52	–  Recording from FM radio or AUX/	68	–  AVCHD (Advanced Video Codec High
	PORTABLE source		Definition)
53	Radio Operations	69	–  About DLNA
53	–  Listening to the radio	69	–  Certain system requirements
53	–  Presetting the radio stations	69	–  Compatibility notes
53	–  Deleting a saved station	70	Audio Output Specifications
53	–  Deleting all the saved stations	71	Area Code List
53	–  Improving poor FM reception	72	Language Code List
54	Playing the iPod	73	Trademarks and Licenses
54	–  Enjoying iPod on the screen	76	Specifications
54	–  Enjoying the iPod IN mode	78	Maintenance
56	Using Bluetooth technology	78	–  Handling the unit
56	–  Listening to music stored on the	78	–  Notes on discs
	Bluetooth devices	79	Important Information relating to Network
58	Using the Premium		Services

58Using the LG Smart World

59–  Signing in

59–  Searching online content

60Using the My Apps Menu

5 Troubleshooting

61Troubleshooting

61–  General

62–  Network

63–  Picture

63 –  Sound

63 –  Customer Support

63 –  Open Source Software Notice

6 Appendix

64Controlling a TV with the Supplied Remote Control

64 –  Setting up the remote to control your TV

Some of the content in this manual may differ from your player depending on the software of the player or your service provider.

1

2

3

4

5

6

1 GettingStarted

8 Getting Started

Introduction

Playable discs and symbols used in this manual

	Media/Term	Logo		Symbol	Description
					yy Discs such as movies that can be purchased or
				e	rented.
					yy “Blu-ray 3D” discs and “Blu-ray 3D ONLY” discs.
	Blu-ray				yy BD-R/RE discs that are recorded in BDAV format.
				y	yy BD-R/RE discs that contain Video, Audio or
				u	Photo files.
				i	yy ISO 9660+JOLIET, UDF and UDF Bridge format
					yy Discs such as movies that can be purchased or
				r	rented.
	DVD-ROM				yy Video mode and finalized only
					yy Supports the dual layer disc also
	DVD-R
	DVD-RW			o	Finalized AVCHD format
	DVD+R
	DVD+RW			y	yy DVD±R/RW discs that contain Video, Audio or
	(8 cm, 12 cm)			u	Photo files.
					yy ISO 9660+JOLIET, UDF and UDF Bridge format
				i
	DVD-RW (VR)			r	VR mode and finalized only
	(8 cm, 12 cm)
	Audio CD			t	Audio CD
	(8 cm, 12 cm)
				y	yy CD-R/RW discs that contain Video, Audio or
	CD-R/RW			u	Photo files.
	(8 cm, 12 cm)				yy ISO 9660+JOLIET, UDF and UDF Bridge format
				i
	Note	–		,	Indicates special notes and operating features.
	Caution	–		>	Indicates cautions for preventing possible damages
					from abuse.

Getting Started	9

,,Note

yy Depending on the conditions of the recording equipment or the CD-R/RW (or DVD±R/RW) disc itself, some CD-R/RW (or DVD±R/RW) discs cannot be played on the unit.

yy Depending on the recording software & the finalization, some recorded discs (CD-R/RW, DVD±R/RW, BD-R/RE) may not be playable.

yy BD-R/RE, DVD±R/RW and CD-R/RW discs recorded using a personal computer or a DVD or CD Recorder may not play if the disc is damaged or dirty, or if there is dirt or condensation on the player’s lens.

yy If you record a disc using a personal computer, even if it is recorded in a compatible format, there are cases in which it may not play because of the settings of the application software used to create the disc. (Check with the software publisher for more detailed information.)

yy This player requires discs and recordings to meet certain technical standards in order to achieve optimal playback quality.

yy Pre-recorded DVDs are automatically set to these standards. There are many different types of recordable disc formats (including CD-R containing MP3 or WMA files) and these require certain pre-existing conditions to ensure compatible playback.

yy Customers should note that permission is required in order to download MP3 / WMA files and audio from the Internet.

Our company has no right to grant such permission. Permission should always be sought from the copyright owner.

yy You have to set the disc format option to [Mastered] in order to make the discs compatible with the LG players when formatting rewritable discs. When setting

the option to Live System, you cannot use it on LG player. (Mastered/Live File System : Disc format system for windows Vista)

About the “7” symbol display

“7” may appear on your TV display during operation and indicates that the function explained in this owner’s manual is not available on that specific media.

Regional code

This unit has a regional code printed on the rear of the unit. This unit can play only BD-ROM or DVD discs labeled same as the rear of the unit or “ALL”.

1 GettingStarted

1 GettingStarted

10 Getting Started

Remote Control

F UNCTION

INFO/M ENU

Battery Installation

Remove the battery cover on the rear of the Remote Control, and insert R03 (size AAA) battery with 4and 5matched correctly.

• • • • • • A• • •

•

FUNCTION: Changes input mode.

SUBTITLE: Selects a subtitle language.

1(POWER): Switches the player ON or OFF.

B(OPEN/CLOSE): Ejects a disc.

SLEEP: Sets a certain period of time after which the unit will switch to off.

INFO/MENU (m): Displays or exits On-Screen Display.

HOME (): Displays or exits the [Home Menu].

DISC MENU: Accesses menu on a disc.

• • • • • • B• • •

•

Direction buttons: Selects an option in the menu.

PRESET +/-: Selects programme of Radio.

TUNING +/-: Tunes in the desired radio station.

ENTER (b): Acknowledges menu selection.

BACK (): Exits the menu or returns to the previous screen.

TITLE/POPUP: Displays the DVD title menu or BD-ROM’s pop-up menu, if available.

Z(STOP): Stops playback. z(PLAY): Starts playback.

M(PAUSE/STEP): Pauses playback.

C/V(SKIP): Goes to the next or previous chapter / track / file.

c/v(SCAN): Searches backward or forward.

• • • • • • C• • •

•

SPEAKER LEVEL: Sets the sound level of desired speaker.

SOUND EFFECT: Selects a sound effect mode.

VOL +/-: Adjusts speaker volume.

OPTICAL/ TV SOUND : Changes input mode to optical directly.

MUTE: Mute the unit.

Colored (R, G, Y, B) buttons:

-Use to navigate BD-ROM menus. They are also used as shortcut buttons for specific menus.

-B button: Selects mono/ stereo in FM mode.

0-9 numerical buttons: Selects numbered options in a menu.

CLEAR: Removes a mark on the search menu or a number when setting the password.

REPEAT (h): Repeats a desired section or sequence.

MUSIC ID: When connected to the network, can provide information about the current song while movie playback.

AUDIO: Selects an audio language or audio channel.

X(REC): Records from an Audio CD, FM radio or AUX source to USB.

?: Marked button is not available.

• • • • • • D• • •

•

TV Control Buttons: See page 64.

Getting Started 11

Front Panel

a	b	c	1
			Started Getting
d e
A Disc Tray	D PORT. IN
B Display Window	E USB (iPod/iPhone/iPad) Port

COperation buttons R(Open / Close) T(Play / Pause) I(Stop)

F (Function)

Changes the input source or function.

VOL -/+ 1/!(Power)

Rear Panel

a

b

c d e f g

h

A AC power cord	G LAN port
B Speakers connectors	H HDMI OUT TO TV
C Cooling Fan
D AUX (L/R) INPUT
E OPTICAL IN
F Antenna Connector

2

Connecting

12 Connecting

Positioning the System

The following illustration shows an example of positioning the system. Note that the illustrations in these instructions differ from the actual unit for explanation purposes.

For the best possible surround sound, all the speakers other than the subwoofer should be placed at the same distance from the listening position (A).

B

C

A G

F

A A

A

A E

>>Caution

yy Be careful to make sure children not to put their hands or any objects into the *speaker duct.

*Speaker duct: A hole for plentiful bass sound on speaker cabinet (enclosure).

yy Place the center speaker at a safe distance from the child’s reach.

Otherwise it may result in the speaker falling down and causing personal injury and/or property damage.

yy The speakers contain magnetic parts, so colour irregularity may occur on the CRT TV screen or PC monitor screen. Please use the speakers away from the TV screen or PC monitor screen.

yy Before using the subwoofer, remove the protective vinyl.

D A

AFront left speaker (L)/ BFront right speaker (R):

Place the front speakers to the sides of the monitor or screen and as flush with the screen surface as possible.

CCenter speaker:

Place the center speaker above or below the monitor or screen.

DSurround left speaker (L)/ ESurround right speaker (R):

Place these speakers behind your listening position, facing slightly inwards.

FSubwoofer:

The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the front speakers. Turn it slightly toward the center of the room to reduce the wall reflections.

GUnit

Connecting 13

Speaker Connection

Attaching the speakers to the player

1.Connect the wires to the unit.

Match each wire’s colored band to the same colored connection terminal on the rear of the unit. To connect the cable to the unit, press each plastic finger pad to open the connection terminal. Insert the wire and release the finger pad.

Connect the black stripe of each wire to the terminals marked -(minus) and the other end to the terminals marked + (plus).

Connect a woofer cord to the player. When connecting a woofer cord to the player, insert the connector until it clicks.

2.Connect the wires to the speakers. Connect the other end of each wire to the

correct speaker according to the color coding:

	Color	Speaker	Position
	Grey	Rear	Rear right
	Blue	Rear	Rear left
	Green	Center	Center
	Orange	Sub	Any front position
		woofer
	Red	Front	Front right
	White	Front	Front left

To connect the cable to the speakers, press each plastic finger pad to open the connection terminals on the base of each speaker. Insert the wire and release the finger pad.

>>Caution

yy Be careful to make sure children do not put their hands or any objects into the *speaker duct.

*Speaker duct : A hole for plentiful bass sound on speaker cabinet (enclosure).

yy The speakers contain magnet parts, so color irregularity may occur on the TV screen or PC monitor screen. Please use the speakers far away from either TV screen or PC monitor.

2

Connecting

2

Connecting

14 Connecting

Connecting to Your TV

If you have a HDMI TV or monitor, you can connect it to this player using a HDMI cable (Type A, High speed HDMI™ cable with Ethernet). Connect the HDMI jack on the player to the HDMI jack on a HDMI compatible TV or monitor.

Rear of the unit

HDMI cable not included

TV

,,Note

yy If a connected HDMI device does not accept the audio output of the player, the HDMI device’s audio sound may be distorted or may not output.

yy When you use HDMI connection, you can change the resolution for the HDMI output. (Refer to “Resolution setting” on page 16 )

yy Select the type of video output from the HDMI OUT jack using [HDMI Color Setting] option on the [Settings] menu (see page 28).

yy Changing the resolution when the connection has already been established may result in malfunctions. To solve the problem, turn off the player and then turn it on again.

yy When the HDMI connection with HDCP is not verified, TV screen is changed to black screen. In this case, check the HDMI

connection, or disconnect the HDMI cable.

yy If there are noises or lines on the screen, please check the HDMI cable (length is generally limited to 4.5 m(15 ft.)).

Set the TV’s source to HDMI (refer to TV’s Owner’s manual).

Additional Information for HDMI

yy When you connect a HDMI or DVI compatible device make sure of the following:

-- Try switching off the HDMI/DVI device and this player. Next, switch on the HDMI/DVI device and leave it for around 30 seconds, then switch on this player.

-- The connected device’s video input is set correctly for this unit.

-- The connected device is compatible with 720x480p, 1280x720p, 1920x1080i or 1920x1080p video input.

yy Not all HDCP-compatible HDMI or DVI devices will work with this player.

-- The picture will not be displayed properly with non-HDCP device.

Connecting 15

What is SIMPLINK?

Some functions of this unit are controlled by the TV’s remote control when this unit and LG TV’s with SIMPLINK are connected through HDMI connection.

Controllable functions by LG TV’s remote control; Play, Pause, Scan, Skip, Stop, Power Off, etc.

Refer to the TV owner’s manual for the details of SIMPLINK function.

LG TV’s with SIMPLINK function has the logo as shown above.

,,Note

Depending on the disc type or playing status, some SIMPLINK operation may differ from your purpose or not work.

ARC (Audio Return Channel) function

The ARC function enables an HDMI capable TV to send the audio stream to HDMI OUT of this player.

To use this function:

-- Your TV must support the HDMI-CEC and ARC function and the HDMI-CEC and ARC must be set to On.

-- The setting method of HDMI-CEC and ARC may differ depending on the TV. For details about ARC function, refer to your TV manual.

-- You must use the HDMI cable (Type A, High Speed HDMI™ cable with Ethernet).

-- You must connect with the HDMI IN that supports the ARC function using the HDMI OUT on this player.

-- You can connect only one Home Theater to TV compatible with ARC.

,,Note

To activate [SIMPLINK / ARC] function, set this option to [On]. (page 32)

2

Connecting

2

Connecting

16 Connecting

Resolution setting

The player provides several output resolutions for HDMI OUT jack. You can change the resolution using [Settings] menu.

1.Press HOME ().

2.Use A/Dto select the [Settings] and press ENTER (b). The [Settings] menu appears.

3.Use W/Sto select [DISPLAY] option then press Dto move to the second level.

4.Use W/Sto select the [Resolution] option then press ENTER (b) to move to the third level.

5.Use W/Sto select the desired resolution then press ENTER (b) to confirm your selection.

,,Note

yy If your TV does not accept the resolution you have set on the player, you can set resolution to 480p as follows:

1. Press Bto open the disc tray.

2 Press Z(STOP) for more than 5 seconds.

yy If you select a resolution manually and then connect the HDMI jack to TV and your TV does not accept it, the resolution setting is set to [Auto].

yy If you select a resolution that your TV does not accept, the warning message will appear. After resolution change,

if you cannot see the screen, please wait 20 seconds and the resolution will automatically revert back to the previous resolution.

yy The 1080p video output frame rate may be automatically set to either 24 Hz or 60 Hz depending both on the capability and preference of the connected TV and

based on the native video frame rate of the content on the BD-ROM disc.

		Connecting 17
Antenna Connection		Connections with
Connect the supplied antenna for listening to the		External Device
radio.
		AUX connection
		You can enjoy the sound from an external
		component through the speakers of this system.
		Connect the analog audio output jacks of your
		component into the AUX L/R (INPUT) on this unit.
		And then select the [AUX] option by pressing
		FUNCTION.
		You can also use the F (Function) button on the
Rear of the unit		front panel to select the input mode.

Rear of the unit

,,Note

Be sure to fully extend the FM wire antenna.

Red

White

To the audio output jacks of your component (TV, VCR, etc.)

2

Connecting

2

Connecting

18 Connecting

PORT. IN connection

You can enjoy the sound from your portable audio player through the speakers of this system.

Connect the headphones (or line out ) jack of the portable audio player into the PORT. IN socket of this unit. And then select the [PORTABLE] option by pressing FUNCTION.

You can also use the F (Function) button on the front panel to select the input mode.

OPTICAL IN connection

You can enjoy the sound from your component with a digital optical connection through the speakers of this system.

Connect the optical output jack of your component into the OPTICAL IN jack on the unit. And then select the [OPTICAL] option by pressing FUNCTION. Or press OPTICAL / TV SOUND to select directly.

You can also use the F (Function) button on the front panel to select the input mode.

Rear of the unit

	To the digital	Optical cable
	optical output jack	not included
MP3 player, etc...	of your component

Connecting 19

Connecting to Your Home Network

This player can be connected to a local area network (LAN) via the LAN port on the rear panel or the internal wireless module.

By connecting the unit to a broadband home network, you have access to services such as software updates, BD-Live interactivity and online content services.

Wired network connection

Using a wired network provides the best performance, because the attached devices connect directly to the network and are not subject to radio frequency interference.

Please refer to the documentation for your network device for further instructions.

Connect the player’s LAN port to the corresponding port on your Modem or Router using a commercially available LAN or Ethernet cable.

,,Note

yy When plugging or unplugging the LAN cable, hold the plug portion of the cable. When unplugging, do not pull on the LAN cable but unplug while pressing down on the lock.

yy Do not connect a modular phone cable to the LAN port.

yy Since there are various connection configurations, please follow the specifications of your telecommunication carrier or internet service provider.

yy If you want to access content from DLNA servers, this player must be connected to the same local area network with them via a router.

yy To set your PC as a DLNA server, install the supplied Nero MediaHome 4 on your PC. (page 38)

Broadband service

Router

DLNA certified servers

Rear of the unit

Wired network setup

If there is a DHCP server on the local area network (LAN) via wired connection, this player will automatically be allocated an IP address. After making the physical connection, a small number of home networks may require the player’s network setting to be adjusted. Adjust the [NETWORK] setting as follow.

Preparation

Before setting the wired network, you need to connect the broadband internet to your home network.

2

Connecting

2

Connecting

20 Connecting

1. Select [Connection Setting] option in the	2. Use W/S/A/Dto select the IP mode
[Settings] menu then press ENTER (b).	between [Dynamic] and [Static].
	Normally, select [Dynamic] to allocate an IP
	address automatically.

2. Read the preparations for the network settings
and then press ENTER (b) while [Start] is		,,Note
highlighted.
	If there is no DHCP server on the network and
	you want to set the IP address manually, select
	[Static] then set [IP Address], [Subnet Mask],
	[Gateway] and [DNS Server] using W/S/
	A/Dand numerical buttons. If you make a
	mistake while entering a number, press CLEAR
	to clear the highlighted part.
Network will automatically be connected to the	3. Select [Next] and press ENTER (b) to apply
unit.		network settings.

	Network connection status is displayed on the
Advanced Setting	screen.

If you want to set the network settings manually, use W/Sto select [Advanced Setting] on the [Network Setting] menu and press ENTER (b).

1.Use W/Sto select [Wired] and press ENTER (b).

4.Press ENTER (b) while [OK] is highlighted to finish the wired network settings.

Connecting 21

Wireless network connection

Wireless network setup

Another connection option is to use an Access Point or a wireless router. The network configuration and connection method may vary depending on the equipment in use and the network environment.

For the wireless network connection, the player needs to be set up for network communication. This adjustment can be done from the [Settings] menu. Adjust the [NETWORK] setting as follow.

Setting up the access point or the wireless router is required before connecting the player to the network.

Wireless

Communication

DLNA certified servers

Access Point or

Wireless Router

Broadband service

Refer to the setup instructions supplied with your access point or wireless router for detailed connection steps and network settings.

For best performance, a direct wired connection from this player to your home network’s router or cable/DSL modem is always the best option.

If you choose to use the wireless option, please note that performance can sometimes be affected by other electronic devices in the home.

Preparation

Before setting the wireless network, you need to:

-- connect the broadband internet to the wireless home network.

-- set the access point or wireless router.

-- note the SSID and security code of the network.

1.Select [Connection Setting] option in the [Settings] menu then press ENTER (b).

2.Read the preparations for the network settings and then press ENTER (b) while [Start] is highlighted.

If wired network is not connected to the unit, all available networks are displayed on the screen.

3.Use W/Sto select a desired SSID of wireless network and press ENTER (b).

2

Connecting

If you have security on your access point, you need to input the security code as necessary.

2

Connecting

22 Connecting

,,Note

If you use other characters than the english alphabet or digits for the SSID name of your access point or wireless router, it may be displayed differently.

,,Note

yy WEP security mode generally have 4 keys available on an access point setting. If your access point or wireless router use WEP security, enter the security code of the key “No.1” to connect on your home network.

yy An Access Point is a device that allows you to connect to your home network wirelessly.

4.Use W/S/A/Dto select the IP mode between [Dynamic] and [Static].

Normally, select [Dynamic] to allocate an IP address automatically.

,,Note

If there is no DHCP server on the network and you want to set the IP address manually, select [Static] then set [IP Address], [Subnet Mask], [Gateway] and [DNS Server] using W/S/ A/Dand numerical buttons. If you make a mistake while entering a number, press CLEAR to clear the highlighted part.

5.Select [Next] and press ENTER (b) to apply network settings.

Advanced Setting

If you want to set the network settings manually, use W/Sto select [Advanced Setting] on the

[Network Setting] menu and press ENTER (b).

1.Use W/Sto select [Wireless] and press ENTER (b).

[AP List] - Scans all available access points or wireless routers within range and display them as a list.

[Network name (SSID)] – Your access point may not be broadcasting its network name (SSID). Check your access point settings through your computer and either set your access

point to broadcast SSID, or manually enter the network name in [Network name(SSID)].

[PBC] – If your access point or wireless router that supports the PBC (Push Button Configuration) method, select this option and press the Push Button on your access point

within 120 counts. You do not need to know the network name (SSID) and security code of your access point.

[PIN] – If your access point supports the PIN Code configuration method based on WPS(WiFi Protected Setup), select this option and note the code number on the screen. And then, enter the PIN number on a setting menu of your access point to connect. Refer to the documentation for your network device.

2.Follow the instructions of each connection method on the screen.

,,Note

To use PBC and PIN network connection, security mode of your access point must be set to OPEN or AES.

Network connection status is displayed on the screen.

6.Select [OK] and press ENTER (b) to complete the network connection.

		Connecting 23
	Notes on network connection	subscriber agreement with your ISP, you may not
	yy Many network connection problems during	be able to use the internet connection feature
		contained in this player or you may be limited
	set up can often be fixed by re-setting the
		to the number of devices you can connect at
	router or modem. After connecting the player
		the same time. (If your ISP limits subscription to
	to the home network, quickly power off and/
		one device, this player may not be allowed to
	or disconnect the power cable of the home
		connect when a PC is already connected.)
	network router or cable modem. Then power on
		yy The use of a “Router” may not be allowed or its
	and/or connect the power cable again.
	yy Depending on the internet service provider (ISP),	usage may be limited depending on the policies
		and restrictions of your ISP. For details, contact
	the number of devices that can receive internet
		your ISP directly.
	service may be limited by the applicable terms
		yy The wireless network operate at 2.4 GHz
	of service. For details, contact your ISP.
	yy Our company is not responsible for any	radio frequencies that are also used by other
		household devices such as cordless telephone,
	malfunction of the player and/or the internet
		Bluetooth® devices, microwave oven, and can be
	connection feature due to communication
		affected by interference from them.
	errors/malfunctions associated with your
		yy Turn off all unused network equipment in
	broadband internet connection, or other
	connected equipment.	your local home network. Some devices may
	yy The features of BD-ROM discs made available	generate network traffic.
		yy For better reception, place the player from the
	through the Internet Connection feature are not
	created or provided by our company, and our	access point as close as possible.
	company is not responsible for their functionality	yy In some instances, placing the access point or
	or continued availability. Some disc related	wireless router at least 0.45 m (1.5 ft.) above the
	material available by the Internet Connection	floor may improve the reception.
	may not be compatible with this player. If you	yy The reception quality over wireless depends on
	have questions about such content, please
		many factors such as type of the access point,
	contact the producer of the disc.
		distance between the player and access point,
	yy Some internet content may require a higher
		and the location of the player.
	bandwidth connection.	yy Set your access point or wireless router to
	yy Even if the player is properly connected and
		Infrastructure mode. Ad-hoc mode is not
	configured, some internet content may not	supported.
	operate properly because of internet congestion,
	the quality or bandwidth of your internet service,
	or problems at the provider of the content.
	yy Some internet connection operations may not
	be possible due to certain restrictions set by the
	Internet service provider (ISP) supplying your
	broadband Internet connection.
	yy Any fees charged by an ISP including, without
	limitation, connection charges are your
	responsibility.
	yy A 10 Base-T or 100 Base-TX LAN port is required
	for wired connection to this player. If your
	internet service does not allow for such a
	connection, you will not be able to connect the
	player.
	yy You must use a Router to use xDSL service.
	yy A DSL modem is required to use DSL service and
	a cable modem is required to use cable modem
	service. Depending on the access method of and

2

Connecting

3

Setting System

24	System Setting
Initial Setup			5. Use W/S/A/Dto select the IP mode
			between [Dynamic] and [Static].
			Normally, select [Dynamic] to allocate an IP
When you turn on the unit for the first time, the			address automatically.
initial setup wizard appears on the screen. Set the
display language and network settings on the initial
setup wizard.
1.	Press 1(POWER).
	The initial setup wizard appears on the screen.

2. Use W/S/A/Dto select a display language

and press ENTER (b).

6. Select [Next] and press ENTER (b) to apply network settings.

3.Read and prepare the preparations for the network settings and then press ENTER (b)

while [Start] is highlighted.	Network connection status is displayed on the
	screen.
	For details on network settings, refer to
	“Connecting to Your Home Network” on page
	19.

If wired network is connected, the network connection setting will automatically be finished.

4.All available networks are displayed on the screen. Use W/Sto select [Wired Network] or desired SSID of wireless network and press ENTER (b).

If you have security on your access point, you need to input the security code as necessary.