Loading...
DVB is a registered trademark of the DVB Project
ID Number(s): 5281: 26LG30D-AA 5282: 32LG30D-AA 5283: 37LG30D-AA 5284: 42LG30D-AA 5583: 32LG50FD-AD 5524: 47LG50FD-AD 5525: 42LG50FD-AD 5463: 47LG50FD-AA 5464: 42LG50FD-AA 5285: 32LG60UD-AA 5461: 47LG60FD-AA 5462: 42LG60FD-AA 5459: 42LG61YD-AC 5582: 47LG61YD-AC 5457: 52LG65YD-AC 5458: 47LG65YD-AC 5454: 52LG70YD-AA 5455: 47LG70YD-AA 5456: 42LG70YD-AA 5798: 32LG60FD-AC 5801: 42LG61YD-AJ 5814: 47LG61YD-AJ 5815: 52LG65YD-AJ 5816: 42LG70YD-AG 5817: 47LG70YD-AG 5802: 52LG70YD-AG
LCD TV
OWNER’S MANUAL
LCD TV MODELS
26LG3*** 32LG6***
32LG3*** 42LG6***
37LG3*** 47LG6***
42LG3*** 52LG6***
32LG5*** 42LG7***
42LG5*** 47LG7***
47LG5*** 52LG7***
Please read this manual carefully before operating
your TV.
Retain it for future reference.
Record model number and serial number of the TV. Refer to the label on the back cover and quote this information.
To your dealer when requiring service.
ACCESSORIES
■Ensure that the following accessories are included with your TV.
■If an accessory is missing, please contact the dealer where you purchased the TV.
■Image shown may differ from your TV.
|
|
|
|
|
|
|
Power Cord |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Owner’s Manual |
Batteries |
||||||
This feature is not available for all models.
* Lightly wipe any stains or fingerprints on the surface of the TV with the polishing cloth.
Polishing Cloth |
Do not use excessive force. This may cause |
|
Polishing cloth for use on |
||
scratching or discolouration. |
||
the screen. |
||
|
Remote Control
Only 32/42/47/52LG6***
(32LG6*** only)
|
|
|
3EA |
4EA |
Cable management clip |
Protection cover |
|
|
|
|
|
(Refer to p.12) |
bolts for stand assembly |
|
|
|
|
||
|
|
|
(Refer to p. 8) |
|
Only 26/32/37/42LG3***, 32/42/47LG5***, 42/47/52LG7*** |
|
|||
(26/32/37LG3*** only) |
|
(26/32/42LG3***, 32/42LG5*** only) |
|
|
x 4 |
x 4 |
|
|
or |
|
|
|
||
Bolts for stand assembly |
1-screw for stand fixing |
|
Protection Cover |
|
(Refer to p.9) |
|
|
||
|
(Refer to p.9) |
|
(Refer to p.12) |
|
|
|
|
||
ACCESSORIES
1
CONTENTS
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
|
PREPARATION |
|
CONTENTS |
Attaching the TV to a Desk......................................... |
9 |
|
Front Panel Controls..................................................... |
4 |
|
Back Panel Information ................................................ |
6 |
|
Stand Installation........................................................... |
8 |
|
Please set it up carefully so the product |
|
|
doesn’t fall over............................................................ |
10 |
|
Back Cover for Wire Arrangement........................... |
11 |
|
Swivel Stand ................................................................. |
11 |
|
Not Using the Desk-type Stand ............................. |
12 |
|
Desktop Pedestal Installation ................................... |
13 |
|
Wall Mount: Horizontal Installation........................ |
13 |
|
Antenna Connection................................................... |
14 |
|
EXTERNAL EQUIPMENT SETUP |
|
|
HD Receiver Setup ...................................................... |
15 |
|
DVD Setup..................................................................... |
18 |
|
VCR Setup..................................................................... |
21 |
|
AV Output Setup ........................................................ |
23 |
|
Digital Audio Out Setup............................................ |
24 |
|
Other A/V Source Setup .......................................... |
25 |
|
Usb in Setup................................................................. |
25 |
|
PC Setup........................................................................ |
26 |
|
- Screen Setup for PC Mode .............................. |
29 |
|
WATCHING TV / PROGRAMME CONTROL |
|
|
Remote Control Key Functions ............................... |
34 |
|
Turning on the TV....................................................... |
36 |
|
Programme Selection ................................................ |
36 |
|
Volume Adjustment ................................................... |
36 |
|
Quick Menu ................................................................. |
37 |
|
On-Screen Menus Selection and Adjustment..... |
38 |
|
Auto Programme Tuning............................................ |
39 |
|
Manual Programme Tuning (In Digital Mode)..... |
40 |
|
Manual Programme Tuning (In Analogue Mode) ... |
41 |
|
Programme Edit ........................................................... |
43 |
|
Booster........................................................................... |
46 |
|
Software Update.......................................................... |
47 |
Diagnostics ................................................................... |
48 |
Selecting the Programme Table............................... |
49 |
Input List........................................................................ |
50 |
................................................................. |
51 |
Input Label .................................................................... |
53 |
AV Mode........................................................................ |
54 |
TO USE THE USB DEVICE |
|
When connecting the USB device.......................... |
55 |
Photo List ...................................................................... |
56 |
Music List........................................................................ |
60 |
EPG (ELECTRONIC PROGRAMME |
|
GUIDE) (IN DIGITAL MODE) |
|
- Switch on/off EPG ............................................... |
63 |
- Select Programme ................................................ |
63 |
- Button Function in NOW/NEXT Guide Mode 64 |
|
- Button Function in 7 Day Guide Mode.......... |
64 |
- Button Function in Date Change Mode......... |
64 |
- Button Function in Extended Description Box . 65 |
|
- Button Function in Remind Setting Mode................. |
65 |
- Button Function in Remind List Mode ............. |
65 |
PICTURE CONTROL |
|
Picture Size (Aspect Ratio) Control ...................... |
66 |
Preset Picture Settings |
|
- Picture Mode-Preset............................................ |
68 |
- Auto Colour Tone Control |
|
(Cool/Medium/Warm)........................................ |
69 |
Manual Picture Adjustment |
|
- Picture Mode-User option................................. |
70 |
- Picture Mode-Expert Control ........................... |
71 |
Picture Improvement Technology........................... |
72 |
Advanced - Film Mode/Real Cinema ..................... |
73 |
Advanced - Black(Darkness) Level.......................... |
74 |
Advanced - Trumotion................................................. |
75 |
TruMotion Demo .......................................................... |
76 |
Eye Care.......................................................................... |
77 |
Picture Reset................................................................. |
78 |
Power Indicator.............................................................. |
79 |
2
SOUND & LANGUAGE CONTROL |
|
Auto Volume Leveller.................................................. |
80 |
Preset Sound Settings - Sound Mode................... |
81 |
Sound Setting Adjustment -User Mode ............... |
82 |
Balance........................................................................... |
83 |
TV Speakers On/ Off Setup..................................... |
84 |
Selecting Digital Audio Out ..................................... |
85 |
Audio Reset................................................................... |
86 |
Stereo Reception |
|
(In Analogue Mode Only)......................................... |
87 |
Speaker Sound Output Selection........................... |
87 |
TIME SETTING |
|
Clock Setup .................................................................. |
88 |
Auto On/ Off Timer Setting..................................... |
89 |
Auto Shut-off Setting ................................................. |
90 |
Time Zone Setup......................................................... |
91 |
Sleep Timer Setting..................................................... |
91 |
PARENTAL CONTROL / RATINGS |
|
Set Password & Lock System................................... |
92 |
Block Programme......................................................... |
93 |
Parental Control .......................................................... |
94 |
Key Lock......................................................................... |
95 |
TELETEXT |
|
Switch on/off ............................................................... |
96 |
SIMPLE Text.................................................................. |
96 |
TOP Text........................................................................ |
96 |
FASTEXT ........................................................................ |
97 |
Special Teletext Functions......................................... |
97 |
APPENDIX |
|
Troubleshooting........................................................... |
98 |
Maintenance ............................................................. |
100 |
Product Specifications ............................................. |
101 |
Programming the Remote Control ....................... |
103 |
IR Codes...................................................................... |
105 |
External Control Device Setup ............................... |
107 |
CONTENTS
3
PREPARATION
FRONT PANEL CONTROLS
■Image shown may differ from your TV.
■If your TV has a protection film attached, remove the film and then wipe the product with a polishing cloth.
PREPARATION |
32/42/47/52LG6*** |
|
|
|
P |
PROGRAMME |
|
|
|
||
|
|
|
|
|
|
|
VOLUME |
|
|
|
OK |
|
Intelligent Sensor |
OK |
|
|
|
|
|
|
Adjusts picture according to the |
|
|
|
surrounding conditions |
|
MENU |
|
|
|
|
|
|
MENU |
|
|
|
|
INPUT |
|
|
INPUT |
|
POWER
Remote Control Sensor
Power/Standby Indicator
•Illuminates red in standby mode.
•Illuminates White when the TV is switched on.
Note: You can adjust Power Indicator in the
OPTION menu.
Only 42LG61**
Intelligent Sensor
Adjusts picture according to the surrounding conditions
4
26/32/37/42LG3***, 32/42/47LG5***
Intelligent Sensor
Adjusts picture according to the surrounding conditions. (32/42/47LG5*** only)
Power/Standby Indicator
• illuminates red in standby mode.
• illuminates blue when the TV is switched on.
Note: You can adjust Power Indicator in the
OPTION menu.
Remote Control Sensor
POWER Button
42/47/52LG7***
Intelligent Sensor
Adjusts picture according to the surrounding conditions.
Power/Standby Indicator
• illuminates red in standby mode.
• illuminates blue when the TV is switched on.
Note: You can adjust Power Indicator in the
OPTION menu.
Remote Control Sensor
POWER Button
P |
PROGRAMME |
+
VOLUME
-
OK
OK
MENU
MENU
INPUT
INPUT
P |
PROGRAMME |
VOLUME
OK 
OK
MENU
MENU
INPUT
INPUT
PREPARATION
5
PREPARATION
BACK PANEL INFORMATION
PREPARATION
■ Image shown may differ from your TV.
32/42/47/52LG6***
|
|
|
|
|
|
USB Input |
|
|
|
|
|
4 |
|
|
|
|
|
|
|
HDMI Input |
|
|
|
|
|
|
Connect a HDMI signal to |
|
|
|
|
|
|
HDMI IN. |
|
|
|
|
|
|
S-Video Input |
|
|
|
|
|
|
Connect S-Video out from |
|
|
|
|
|
|
an S-VIDEO device. |
2 |
3 |
|
4 |
|
1 |
|
|
RGB IN |
|
|
|
|
Audio/Video Input |
|
|
|
HDMI/DVIIN |
|
Connect audio/video |
|
|
INRGB(PC) |
|
|
AV IN |
||
|
|
|
|
|||
|
|
|
|
output from an external |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
device to these jacks. |
COMPONENTIN VIDEO |
AUDIO |
(RGB/DVI) |
RGB IN |
|
8 |
|
|
AUDIO |
OUTAV |
|
|
|
|
|
|
VIDEO |
|
|
9 |
|
|
|
|
|
|
|
|
AUDIO |
|
|
|
|
|
|
1 |
2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
5 |
6 |
7 |
|
||
1 |
Power Cord Socket |
|
|
6 |
OPTICAL DIGITAL AUDIO OUT |
|
|
This TV operates on an AC power. The voltage is |
|
Connect digital audio from various types of equipment. |
|||
|
indicated on the Specifications page. Never |
|
Note: In standby mode, these ports do not work. |
|||
|
attempt to operate the TV on DC power. |
|
|
|||
|
RS-232C IN (CONTROL & SERVICE) PORT |
7 |
Antenna Input |
|||
2 |
|
Connect RF antenna to this jack. |
||||
|
Connect to the RS-232C port on a PC. |
|
||||
|
|
|
||||
|
RGB Input |
|
|
8 |
RGB/DVI Audio Input |
|
3 |
|
|
|
Connect the audio from a PC. |
||
|
Connect the output from a PC. |
|
||||
|
|
|
||||
|
|
|
|
|
9 |
AV OUT |
4 |
HDMI Input |
|
|
|
Connect second TV or monitor to the AV OUT |
|
|
Connect a HDMI signal to HDMI IN. |
|
socket on the set. |
|||
|
Or DVI(VIDEO)signal to HDMI/DVI port with DVI |
|
|
|||
|
to HDMI cable. |
|
|
|
|
|
5 |
Component Input |
|
|
|
|
|
|
Connect a component video/audio device to |
|
|
|||
6these jacks.
■ Image shown may differ from your TV. |
42/47/52LG7*** 26/32/37/42LG3***, 32/42/47LG5*** |
1
42/47/52LG7***
23
RGB IN |
|
|
RGB(PC) |
AUDIO |
|
(RGB/DVI) |
||
|
||
HDMI/DVI IN |
|
|
2 |
2 |
|
1 |
1 |
|
(DVI) |
AUDIO |
|
VIDEO |
COMPONENT IN
5
|
|
|
USB Input |
|
USB SERVICEONLY |
|
USB Input |
|
|
|||
|
|
|
|
|
|
|
(Service only) |
|
||||
|
|
|
|
3 |
|
3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
HDMI Input |
|
|
||
|
|
|
|
|
|
|
|
Connect a HDMI signal |
||||
|
|
|
|
|
|
|
|
to HDMI IN. |
|
|
||
|
|
|
|
|
|
|
|
S-Video Input |
|
|||
|
|
|
|
|
|
|
|
Connect S-Video out |
||||
|
|
|
|
|
|
|
|
from an S-VIDEO device. |
||||
|
|
|
|
|
|
|
|
Audio/Video Input |
|
|||
|
|
|
|
|
|
|
|
Connect |
audio/video |
|||
|
|
|
|
|
|
|
|
output from an external |
||||
|
|
|
|
AV IN 2 |
|
AV IN 2 |
|
device to these jacks. |
||||
|
|
4 |
|
26/32/37/42LG3***, 32/42/47LG5*** |
|
|||||||
|
|
|
2 |
|
|
3 |
|
4 |
|
|
|
|
|
|
|
ANTENNA IN |
8 |
|
|
|
|
ANTENNA IN |
|
||
DIGITAL |
|
|
|
RGB IN |
|
|
DIGITAL |
|
|
|||
VIDEO OUT |
|
|
|
|
|
VIDEO OUT |
|
|||||
AUDIO OUT |
|
9 |
|
RGB(PC) |
AUDIO |
AUDIO OUT |
|
|||||
OPTICAL |
|
|
|
OPTICAL |
|
|
||||||
|
|
|
(RGB/DVI) |
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
||
|
RS-232C IN |
AUDIO OUT |
HDMI/DVI IN |
|
|
|
|
|
RS-232C IN |
AUDIO OUT |
||
(CONTROL & SERVICE) |
|
|
2 |
|
|
|
(CONTROL & SERVICE) |
|
||||
|
|
|
|
2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IN 1 |
|
|
1 |
1 |
|
|
|
|
IN 1 |
|
|
|
AV |
|
|
(DVI) |
|
VIDEO |
|
AUDIO |
|
AV |
|
|
|
VIDEO |
|
|
|
|
|
VIDEO |
|
||||
|
|
|
|
|
COMPONENT IN |
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|||
6 |
7 |
|
|
|
|
5 |
|
|
6 |
7 |
|
|
1Power Cord Socket
This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power.
2HDMI Input
Connect a HDMI signal to HDMI IN.
Or DVI(VIDEO)signal to HDMI/DVI port with DVI to HDMI cable.
3RGB/Audio Input
Connect the monitor output from a PC to the appropriate input port.
4Antenna Input
Connect RF antenna to this jack.
6RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
7Audio/Video Input(AV IN 1)
Connect audio/video output from an external device to these jacks.
8OPTICAL DIGITAL AUDIO OUT
Connect digital audio from various types of equipment. Note: In standby mode, these ports do not work.
9AUDIO/VIDEO OUT
Connect second TV or monitor to the AUDIO/VIDEO OUT socket on the set.
5Component Input
Connect a component video/audio device to these jacks.
8
9
PREPARATION
7
PREPARATION
PREPARATION
STAND INSTALLATION (Only 32LG6***)
■ Image shown may differ from your TV.
When assembling the desk type stand, check whether the bolt is fully tightened.
(If not tightened fully, the product can tilt forward after the product installation.) If you tighten the bolt with excessive force, the bolt can deviate from abrasion of the tightening part of the bolt.
1 Carefully place the TV screen side down on a |
3 Assemble the TV as shown. |
cushioned surface to protect the screen from |
|
damage. |
|
2 Assemble the parts of the Stand Body with |
4 |
Fix the 4 bolts securely using the holes in the |
Cover Base of the TV. |
|
back of the TV. |
|
|
Stand Body
Cover Base
8
(Only 26/32/37LG3***)
1 Carefully place the TV screen side down on a 3 Assemble the TV as shown. cushioned surface to protect the screen from
damage.
2Assemble the parts of the Stand Body with the Cover Base of the TV.
Stand Body
Cover Base
4 |
Fix the 4 bolts |
securely using the holes in the |
back of the TV. |
|
ATTACHING THE TV TO A DESK (Only 26/32/42LG3***, 32/42LG5***)
The TV must be attached to desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. Use only an attached screw.
Stand |
1-Screw
(provided as parts of the product)
Desk
! WARNING
GTo prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury.
PREPARATION
9
PREPARATION
PREPARATION
PLEASE SET IT UP CAREFULLY SO THE PRODUCT DOESN’T FALL OVER.
A You should purchase necessary components to fix the TV to the wall on the market.
A Position the TV close to the wall to avoid the possibility of it falling when pushed.
A The instructions shown below are a safer way to set up the TV, which is to fix it to the wall, avoiding the possibility of it falling forwards if pulled. This will prevent the TV from falling forward and causing injury. This will also prevent the TV from damage. Ensure that children do not climb or hang from the TV.
1 |
2 |
1 |
2 |
1Use the eye-bolts or TV brackets/bolts to fix the product to the wall as shown in the picture. (If your TV has bolts in the eyebolts, loosen then bolts.)
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
2Secure the wall brackets with the bolts on the wall. Match the height of the bracket that is mounted on the wall.
3
3Use a sturdy rope to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product.
! NOTE
GWhen moving the TV undo the cords first.
GUse a platform or cabinet strong and large enough to support the size and weight of the TV.
GTo use the TV safely make sure that the height of the bracket on the wall and on the TV is the same.
10
BACK COVER FOR WIRE ARRANGEMENT
■ Image shown may differ from your TV.
32/42/47/52LG6***
Align the hole with the tab on the CABLE MANAGEMENT CLIP.
1Turn the CABLE MANAGEMENT CLIP as shown.
Note: This cable management can be broken by excessive pressure.
2Connect the cables as necessary.
To connect additional equipment, see the External Equipment Setup section.
PREPARATION
SWIVEL STAND
This feature is not available for all models.
After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit your viewing position.
11
PREPARATION
26/32/37/42LG3***, 32/42/47LG5***, 42/47/52LG7***
|
1 Connect the cables as necessary. |
3 Fit the CABLE MANAGEMENT CLIP as |
|
To connect additional equipment, see the |
shown. |
|
External Equipment Setup section of the manual. |
|
|
|
|
|
|
|
PREPARATION
2Open the CABLE MANAGEMENT CLIP as shown and manage the cables.
CABLE MANAGEMENT CLIP
NOT USING THE DESK-TYPE STAND
When installing the wall-mounted unit, use the protection cover for desk-type stand installation.
■ Image shown may differ from your TV.
32/42/47/52LG6***
26/32/37/42LG3***, 32/42/47LG5***, 42/47/52LG7***
After removing the protection paper from the |
Insert the PROTECTION COVER into the TV |
protection cover, adhere it to the TV as shown. |
until clicking sound. |
12
AThe TV can be installed in various ways such as on a wall, or on a desktop etc.
AThe TV is designed to be mounted horizontally.
EARTHING
Ensure that you connect the earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker.
Do not try to earth the TV by connecting it to telephone wires, lightening rods or gas pipes.
DESKTOP PEDESTAL INSTALLATION
For adequate ventilation allow a clearance of 4” (10cm) all around the TV.
4 inches
4 inches
4 inches |
|
|
|
|
|
|
|
|
4 inches |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Power Supply
Circuit breaker
WALL MOUNT: HORIZONTAL INSTALLATION
For adequate ventilation allow a clearance of 4” (10cm) all around the TV. We recommend that you use a wall mounting bracket of LG brand when mounting the TV to a wall.
|
4 inches |
|
4 inches |
4 inches |
4 inches |
|
|
|
4 inches |
PREPARATION
13
PREPARATION
PREPARATION
■ To prevent damage do not connect to the mains outlet until all connections are made between the devices.
ANTENNA CONNECTION
■ For optimum picture quality, adjust antenna direction.
■ An antenna cable and converter are not supplied.
Wall
Antenna
Socket
Outdoor
Antenna
(VHF, UHF)
Antenna
Multi-family Dwellings/Apartments (Connect to wall antenna socket)
RF Coaxial Wire (75 ohm)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
UHF
Signal
Amplifier
VHF
■In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier to the antenna as shown above.
■If signal needs to be split for two TVs, use an antenna signal splitter for connection.
14
EXTERNAL EQUIPMENT SETUP
■To avoid damaging any equipment, never plug in any power cords until you have finished connecting all equipment.
■This section on EXTERNAL EQUIPMENT SETUP mainly uses diagrams for the 42LG6***/42LG7*** model.
■Image shown may differ from your TV.
HD RECEIVER SETUP
■This TV can receive Digital RF/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the diagram as shown below.
Connecting with a component cable
1
Connect the video outputs (Y, PB, PR) of the digital set
top box to the COMPONENT IN VIDEO jacks on the TV.
2Connect the audio output of the digital set-top box to the COMPONENT IN AUDIO jacks on the TV.
3Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
4Select Component1 input source using the INPUT button on the remote control. If connected to COMPONENT IN 2 input, select Component 2 input source.
|
|
2 |
|
|
INCOMPONENT |
VIDEO |
1 |
|
|
VIDEO |
AUDIO |
|||
1 |
|
|||
|
|
COMPONENT IN |
|
|
|
or |
|
AUDIO |
|
|
|
2 |
|
|
|
1 |
2 |
1 |
2 |
|
|
SETUP EQUIPMENT EXTERNAL
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Signal |
|
|
|
|
Component |
HDMI |
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
480i/576i |
|
|
|
|
Yes |
No |
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
480p/576p |
|
|
|
|
Yes |
Yes |
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
720p/1080i |
|
|
|
|
Yes |
Yes |
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
1080p |
|
|
|
|
Yes |
Yes |
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
(50/60Hz only) |
(24Hz/30Hz/50Hz/60Hz) |
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
15
EXTERNAL EQUIPMENT SETUP
Connecting a set-top box with an HDMI cable
SETUP EQUIPMENT EXTERNAL
1Connect the digital set-top box to HDMI/DVI IN 1, HDMI IN 2, HDMI IN 3 or HDMI IN 4(only 32/42/47/52LG6***) jack on the TV.
2Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
3Select HDMI1, HDMI2, HDMI3 or HDMI4(only 32/42/47/52LG6***) input source using the INPUT button on the remote control.
HDMI/DVI IN
or
1
HDMI/DVI IN
2
1
(DVI)
1
16
Connecting with an HDMI to DVI cable
1Connect the digital set-top box to HDMI/DVI IN 1 jack on the TV.
2Connect the audio output of the digital set-top box to the AUDIO (RGB/DVI) jack on the TV.
3Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)
4 Select HDMI1 input source using the INPUT button on the remote control.
RGB IN
RGB(PC) |
AUDIO |
A |
|
O |
|||
(RGB/DVI) |
|||
|
|
IN
|
|
|
IN |
HDMI/DVI IN |
|
|
|
|
|
|
HDMI/DVI |
|
|
|
|
|
|
|
|
|
|
(C |
|
|
|
|
|
|
|
|
|
|
|
|
|
2 |
|
|
|
|
|
|
|
Y |
PB |
PR |
R |
AUDIO |
(RGB/DVI) |
RGBIN |
|
1 |
|
|
|
|
(DVI) |
VIDEO |
|
AUDIO |
|||
|
|
|
|
|
|||
|
|
|
|
|
|
||
|
|
|
|
|
COMPONENT IN |
||
|
VIDEO |
OUT |
2 |
1 |
|
|
|
|
AUDIO |
AV |
|
|
|
|
|
|
|
|
|
or |
|
|
|
|
|
|
|
1 |
|
|
2 |
SETUP EQUIPMENT EXTERNAL
17
EXTERNAL EQUIPMENT SETUP
SETUP EQUIPMENT EXTERNAL
DVD SETUP
Connecting with a component cable
1Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT IN VIDEO jacks on the TV.
2Connect the audio outputs of the DVD to the COMPONENT IN AUDIO jacks on the TV.
3Turn on the DVD player, insert a DVD.
4Select Component1 input source using the INPUT button on the remote control. If connected to COMPONENT IN 2 input, select Component 2 input source.
5Refer to the DVD player's manual for operating instructions.
|
|
2 |
|
|
1 |
|
VIDEO |
AUDIO |
INCOMPONENT VIDEO |
COMPONENT IN |
|
or |
|
|
1 |
|
|
|
|
|
AUDIO |
1 |
2 |
|
||
2 |
|
|
1 |
2 |
|
Component Input ports
To achieve better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the TV |
Y |
PB |
PR |
|
|
|
|
|
|
|
|
|
Y |
PB |
PR |
Video output ports |
Y |
B-Y |
R-Y |
on DVD player |
Y |
Cb |
Cr |
|
Y |
Pb |
Pr |
|
|
|
|
18
Connecting with a S-Video cable
1 |
Connect the S-VIDEO output of the DVD to the S - |
|
|
|
||||||||||||||
VIDEO input on the TV. |
|
|
|
|
|
|
||||||||||||
|
|
|
|
|
|
|||||||||||||
|
|
|
|
|
|
|
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
2 |
Connect the audio outputs of the DVD to the AUDIO |
|
|
|
|
|
|
|||||||||||
|
|
|
|
|
|
|||||||||||||
3 |
input jacks on the TV. |
|
|
|
|
|
||||||||||||
|
|
|
|
|||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Turn on the DVD player, insert a DVD. |
|
|
|
|
|
|||||||||||||
4 |
Select A V input source using the INPUT button on |
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|||||||||
5 |
the remote control. |
|
|
|
|
|
|
|
|
|
|
|||||||
Refer to the DVD player's manual for operating instruc- |
|
|
|
|
|
|
||||||||||||
|
|
|
|
|||||||||||||||
|
tions. |
|
|
|
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
AV IN
VIDEO |
S-VIDEO |
L |
R |
ANT IN |
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ANT OUT
12
SETUP EQUIPMENT EXTERNAL
19
EXTERNAL EQUIPMENT SETUP
Connecting the HDMI cable
Connect the HDMI output of the DVD to the
1HDMI/DVI IN 1, HDMI IN 2, HDMI IN 3 or HDMI IN 4(only 32/42/47/52LG6***) jack on the TV.
2Select HDMI1, HDMI2, HDMI3 or HDMI4(only 32/42/47/52LG6***) input source using the INPUT
button on the remote control.
EXTERNAL |
3 Refer to the DVD player's manual for operating |
||
|
|||
|
|
instructions. |
|
EQUIPMENT |
|
|
|
! |
ously when using a HDMI cable. |
||
|
NOTE |
||
SETUP |
G The TV can receive video and audio signals simultane- |
||
G If the DVD does not support Auto HDMI, you must set |
|||
|
|||
the output resolution appropriately.
HDMI/DVI IN
or
1
HDMI/DVI IN
2
1
(DVI)
1
20
VCR SETUP
■To avoid picture noise (interference), allow adequate distance between the VCR and TV.
■Typically a frozen still picture from a VCR. If 4:3 picture format is used for an extended period the fixed images on the sides of the screen may remain visible.
Connecting with a RF Cable
ANT OUT S-VIDEO VIDEO |
L |
R |
1
OUTPUT
SWITCH
Wall Jack
2
or
Antenna |
|
|
|
ANT OUT S-VIDEO VIDEO L |
R |
ANTENNA IN |
1 |
|
VIDEO OUT |
|
|
|
OUTPUT |
|
|
SWITCH |
|
AUDIO OUT |
|
|
IN |
|
|
RVICE) |
Wall Jack |
|
2
IDEO 
/MONO AUDIO
Antenna
1Connect the ANT OUT socket of the VCR to the ANTENNA IN socket on the TV.
2 Connect the antenna cable to the ANT IN socket of the VCR.
3Press the PLAY button on the VCR and match the appropriate channel between the TV and VCR for viewing.
SETUP EQUIPMENT EXTERNAL
21
EXTERNAL EQUIPMENT SETUP
SETUP EQUIPMENT EXTERNAL
Connecting with a RCA cable
1 |
Connect the AUDIO/VIDEO jacks between TV and |
|
|
|
VCR. Match the jack colours (Video = yellow, Audio Left |
|
|
|
= white, and Audio Right = red) |
|
|
2 |
Insert a video tape into the VCR and press PLAY on |
1 |
|
|
the VCR. (Refer to the VCR owner’s manual.) |
|
|
|
|
|
|
3 |
Select A V input source using the INPUT button on |
AV IN |
|
|
the remote control. |
|
|
! |
NOTE |
S-VIDEO VIDEO L |
R ANT IN |
|
|
||
G If you have a mono VCR, connect the audio cable from the |
SWITCH |
|
|
|
VCR to the AUDIO L/MONO jack of the TV. |
ANT OUT |
|
|
|
OUTPUT |
|
Connecting with a S-Video cable
Connect the S-VIDEO output of the VCR to the S - 1 VIDEO input on the TV set. The picture quality is improved; compared to normal composite (RCA cable)
input.
2Connect the audio outputs of the VCR to the AUDIO
input jacks on the TV.
3Insert a video tape into the VCR and press PLAY on the
VCR. (Refer to the VCR owner’s manual.)
4 Select A V input source with using the INPUT button on the remote control.
AV IN
! NOTE
GIf both S-VIDEO and VIDEO sockets have been connected to the S-VHS VCR simultaneously, only the S-VIDEO can be received.
VIDEO |
S-VIDEO |
L |
R |
ANT IN |
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ANT OUT
12
22
AV OUTPUT SETUP
The TV has a special signal output capability which allows you
to hook up the second TV or monitor.
Connect the second TV or monitor to the TV’s AV OUT 1 jacks.
See the Operating Manual of the second TV or monitor
2for further details regarding that device’s input settings.
!NOTE
G Only Digital, Analogue mode can be used for AV out. Component, RGB, HDMI input sources cannot be used for AV out.
G We recommend to use the AV OUT jacks for VCR recording.
AUDIO |
(RGB/DVI) |
RGB IN |
|
VIDEO |
OUT |
|
AUDIO |
AV |
1
DIGITAL |
VIDEO OUT |
AUDIO OUT |
) OPTICAL
AUDIO OUT
RS-232C (CONTROL &
R
or |
IN 1 |
|
UDIO |
AV |
VIDEO |
|
|
1
|
|
|
|
|
|
|
|
|
|
VIDEO |
L |
R |
S-VIDEO |
|
|
|
|
|
|
S-VIDEO
VIDEO |
|
|
|
|
|
L |
R |
SETUP EQUIPMENT EXTERNAL
23
EXTERNAL EQUIPMENT SETUP
DIGITAL AUDIO OUT SETUP
Sending the TV’s audio signal to external audio equipment via the Digital Audio Output (Optical) port.
SETUP EQUIPMENT EXTERNAL
1 |
Connect one end of an optical cable to the TV Digital |
|
|
Audio (Optical) Output port. |
1 |
2Connect the other end of the optical cable to the digital audio (Optical) input on the audio equipment.
3 |
Set the “TV Speaker option - Off ” in the AUDIO |
2 |
||
|
|
|
||
|
menu.(Gp.84). Refer to the external audio equipment |
|
|
|
|
instruction manual for operation. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CAUTION
GDo not look into the optical output port. Looking at the laser beam may damage your vision.
|
|
|
or |
|
|
! |
NOTE |
|
|
|
|
G When connecting with external audio equipments, such as |
IN |
|
|
|
|
|
amplifiers or speakers, please turn the TV speakers off. |
DIGITAL |
VIDEO OUT |
|
|
|
|
|
|||
|
|
AUDIO |
AUDIO OUT |
|
|
|
|
(RGB/DVI) |
OPTICAL |
|
|
|
|
|
232C IN |
AUDIO OUT |
|
|
|
|
|
||
|
|
2 |
|
SERVICE) |
|
|
|
|
|
|
|
|
|
L |
R |
|
|
|
|
1 |
|
|
|
|
|
AUDIO |
1 |
VIDEO |
/MONO AUDIO |
|
|
ONENT IN |
|
||
|
|
|
|
|
|
|
|
|
2 |
|
|
24
OTHER A/V SOURCE SETUP
Camcorder
Video Game Set
VIDEO L R
1
AV IN
1Connect the AUDIO/VIDEO jacks between TV and external equipment. Match the jack colours . (Video = yellow, Audio Left = white, and Audio Right = red)
2 Select A V input source with using the INPUT button on the remote control.
3Operate the corresponding external equipment. Refer to external equipment operating guide.
USB IN SETUP
Only 32/42/47/52LG6***, 42/47/52LG7***
1 Connect the USB device to the USB IN jacks on the side of TV.
1
2 After connecting the USB IN jacks, you use the USB
function. (G p.55)
SETUP EQUIPMENT EXTERNAL
25
EXTERNAL EQUIPMENT SETUP
SETUP EQUIPMENT EXTERNAL
PC SETUP
This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
Connecting with a D-sub 15 pin cable
1Connect the RGB output of the PC to the RGB IN (PC) jack on the TV.
2Connect the PC audio output to the AUDIO (RGB/DVI) jack on the TV.
3Turn on the PC and the TV
4Select RGB input source using the INPUT button on the remote control.
|
|
|
|
RGB IN |
|
DIGIT |
|
|
|
|
|
|
|
|
|
|
|
RGB(PC) |
AUDIO |
AUDIO |
|
|
|
|
(RGB/DVI) |
OPTI |
|
|
|
|
|
|
|
|
RGB IN |
|
|
|
HDMI/DVI IN |
|
RS |
|
IN |
|
|
|
(CONTR |
|
|
|
|
|
|
||
RGBIN(PC) |
|
|
2 |
|
|
|
|
HDMI/DVI |
|
|
|
||
|
|
1 |
L |
R |
||
|
|
|
|
1 |
||
|
|
|
|
(DVI) |
AUDIO |
|
|
|
|
|
|
|
|
AUDIO |
(RGB/DVI) |
RGB IN |
|
|
IN |
|
|
|
|
|
|||
|
VIDEO |
OUT |
|
or |
|
|
|
AUDIO |
AV |
2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 |
2 |
|
2 |
|
|
|
|
|
|
|
|
|
AUDIO |
RGB OUTPUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
RGB OUTPUT |
AUDIO |
|
|
|
|
|
|
|
26
Connecting with a HDMI to DVI cable
1Connect the DVI output of the PC to the HDMI/DVI IN1 jack on the TV.
2Connect the PC audio output to the AUDIO (RGB/DVI) jack on the TV.
3Turn on the PC and the TV.
4Select HDMI1 input source using the INPUT button on the remote control.
|
|
|
|
|
|
|
RGB IN |
|
DIGITAL |
|
|
|
|
|
|
|
|
|
|
VIDEO OU |
|
|
|
|
|
|
|
RGB(PC) |
AUDIO |
AUDIO OUT |
||
IN |
|
|
|
|
|
(RGB/DVI) |
OPTICAL |
|
||
|
|
IN |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
HDMI/DVI |
|
HDMI/DVI IN |
|
|
|
RS-232C IN |
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
(CONTROL & SERVICE) |
|
|
|
|
|
|
2 |
|
|
|
|
|
AUDIO |
(RGB/DVI) |
RGBIN |
|
|
Y |
PB |
PR |
AUDIO |
R |
|
|
1 |
(DVI) |
VIDEO |
AVIN 1 |
|
|||||
|
|
|
|
1 |
|
|
|
|
|
|
|
VIDEO |
|
|
|
|
COMPONENT IN |
|
VIDEO |
||
|
|
|
|
|
|
|
||||
|
OUT |
|
|
|
|
|
|
|
|
|
|
AUDIO |
AV |
2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
or |
|
|
|
|
|
|
|
|
|
|
1 |
|
|
2 |
|
|
|
|
|
AUDIO |
DVI-PC OUTPUT |
|
|
|
|
|
|
DVI-PC OUTPUT |
AUDIO |
SETUP EQUIPMENT EXTERNAL
27
EXTERNAL EQUIPMENT SETUP
SETUP EQUIPMENT EXTERNAL
Supported Display Resolution
RGB-PC, HDMI-PC mode
|
Resolution |
Horizontal |
Vertical |
|
|
|
Frequency(kHz) |
Frequency(Hz) |
|
||
|
|
|
|||
|
|
|
|
|
|
|
720x400 |
31.468 |
70.08 |
|
|
|
640x480 |
31.469 |
59.94 |
|
|
|
800x600 |
37.879 |
60.31 |
|
|
|
1024x768 |
48.363 |
60.00 |
|
|
|
|
|
|
|
|
|
|
56.470 |
70.00 |
|
|
|
1280x768 |
47.78 |
59.87 |
|
|
|
1360x768 |
47.72 |
59.8 |
|
|
|
1366x768 |
47.56 |
59.6 |
|
|
|
1280x1024 |
63.595 |
60.0 |
|
|
|
1920x1080 |
66.647 |
59.988 |
|
|
|
|
|
|||
|
|
|
|
|
|
Only 32LG60F*, 42/47/52LG6***, 32/42/47LG5***, 42/47/52LG7***
! NOTE
G To enjoy vivid picture and sound, connect a PC to the TV.
G Avoid keeping a fixed image on the set’s screen for prolonged periods of time. The fixed image may become permanently imprinted on the screen; use a screen saver when possible.
G Connect the PC to the RGB (PC) or HDMI IN (or HDMI/DVI IN) port of the TV; change the resolution.
G There may be interference relating to resolution, vertical pattern, contrast or brightness in PC mode. Change the PC mode to another resolution or change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.
G The synchronization input waveform for Horizontal and Vertical frequencies are separate.
G Connect the signal cable from the monitor output port of the PC to the RGB (PC) port of the TV or the signal cable from the HDMI output port of the PC to the HDMI IN (or HDMI/DVI IN) port on the TV.
G Connect the audio cable from the PC to the Audio input on the TV. (Audio cables are not included with the TV).
G If using a sound card, adjust PC sound as required.
G This TV uses a VESA Plug and Play Solution. The TV provides EDID data to the PC system with a DDC protocol. The PC adjusts automatically when using this TV.
G DDC protocol is preset for RGB (Analogue RGB), HDMI (Digital RGB) mode.
G If required, adjust the settings for Plug and Play functionality
G If the graphic card on the PC does not output analogue and digital RGB simultaneously, connect only one of either RGB or HDMI IN (or HDMI/DVI IN) to display the PC output on the TV.
G If graphic card on the PC does output analogue and digital RGB simultaneously, set the TV to either RGB or HDMI; (the other mode is set to Plug and Play automatically by the TV.)
G DOS mode may not work depending on the video card if you use a HDMI to DVI cable.
G If you use too long an RGB-PC cable, there may be interference on the screen. We recommend using under 5m of cable. This provides the best picture quality.
G When an unsupported resolution or graphic card is used on the PC, it may cause some errors.
28
Loading...