LG Electronics 32CS461, 42CS530, 42CS560, 47LS4500, 7CS560 User Manual

OWNER’S MANUAL

LED LCD TV / LCD TV

Please read this manual carefully before operating your set and retain it for future reference.

LED LCD TV MODELS				LCD TV MODELS
32LS3400	22LS3500	22LS3510	47LS4500	32CS460	32CS560
42LS3400	26LS3500	26LS3510	55LS4500	32CS461	37CS560
32LS3410	32LS3500	32LS3510		42CS530	42CS560
32LS3450
42LS3450

P/NO : MFL67468111 (1208-REV08) www.lg.com

ENGLISH

2 IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

Always comply with the following precautions to avoid dangerous situations and ensure peak performance of your product.

WARNING/CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING/CAUTION

- TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Wash hands after handling.

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

yyDo not use this apparatus near water.

yyClean only with a dry cloth.

yyDo not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

yyDo not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

yyDo not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet (Can differ by country).

IMPORTANT SAFETY INSTRUCTIONS 3

yyProtect the power cord from being walked on

yyKeep the packing anti-moisture material or

or pinched particularly at plugs, convenience

vinyl packing out of the reach of children.

receptacles, and the point where they exit

Anti-moisture material is harmful if

from the apparatus.

swallowed. If swallowed by mistake, force

the patient to vomit and visit the nearest

hospital. Additionally, vinyl packing can

cause suffocation. Keep it out of the reach of

children.

yyOnly use attachments/accessories specified

yyCAUTION concerning the Power Cord

by the manufacturer.

(Can differ by country):

It is recommended that appliances be

placed upon a dedicated circuit; that is, a

single outlet circuit which powers only that

yyUse only with a cart, stand, tripod, bracket,

appliance and has no additional outlets or

or table specified by the manufacturer, or

branch circuits. Check the specification page

sold with the apparatus. When a cart is used,

of this owner’s manual to be certain. Do not

use caution when moving the cart/apparatus

connect too many appliances to the same

combination to avoid injury from tip-over.

AC power outlet as this could result in fire or

electric shock. Do not overload wall outlets.

Overloaded wall outlets, loose or damaged

wall outlets, extension cords, frayed power

cords, or damaged or cracked wire insulation

yyUnplug this apparatus during lightning

are dangerous. Any of these conditions could

storms or when unused for long periods of

result in electric shock or fire. Periodically

time.

examine the cord of your appliance, and

if its appearance indicates damage or

deterioration, unplug it, discontinue use of

the appliance, and have the cord replaced

with an exact replacement part by an

yyRefer all servicing to qualified service

authorized service. Protect the power cord

personnel. Servicing is required when

from physical or mechanical abuse, such as

the apparatus has been damaged in any

being twisted, kinked, pinched, closed in a

way, such as power-supply cord or plug is

door, or walked upon. Pay particular attention

damaged, liquid has been spilled or objects

to plugs, wall outlets, and the point where

have fallen into the apparatus, the apparatus

the cord exits the appliance. Do not move

has been exposed to rain or moisture, does

the TV with the power cord plugged in. Do

not operate normally, or has been dropped.

not use a damaged or loose power cord. Be

sure do grasp the plug when unplugging the

power cord. Do not pull on the power cord

to unplug the TV.

yyDo not stick metal objects or any other

conductive material into the power cord. Do

not touch the end of the power cord while it

is plugged in.

ENGLISH

ENGLISH

4 IMPORTANT SAFETY INSTRUCTIONS

yyWarning - To reduce the risk of fire or electrical shock, do not expose this product to rain, moisture or other liquids. Do not touch the TV with wet hands. Do not install this product near flammable objects such as gasoline or candles, or expose the TV to direct air conditioning.

yyDo not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g. on shelves above the unit).

yyGrounding

(Except for devices which are not grounded.) Ensure that you connect the earth ground wire to prevent possible electric shock

(i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.

Power Supply

Short-circuit

Breaker

yyDISCONNECTING DEVICE FROM THE MAIN POWER

Mains plug is the disconnecting device. The plug must remain readily operable.

yyAs long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if the unit is turned off.

yyDo not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product.

yyANTENNAS Outdoor antenna grounding

(Can differ by country):

If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur. Be sure the antenna system is grounded so as to provide some protection against voltage surges

and built-up static charges. Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode.

Antenna grounding according to the National Electrical Code, ANSI/NFPA 70

Ground Clamp

Antenna Lead in Wire

Antenna Discharge Unit

Electric Service

(NEC Section 810-20)

Equipment

Grounding Conductor

Ground Clamp

(NEC Section 810-21)

Power Service Grounding

NEC: National Electrical Code Electrode System

(NEC Art 250, Part H)

					IMPORTANT SAFETY INSTRUCTIONS 5
yyCleaning					yyDot Defect
When cleaning, unplug the power cord and					The Plasma or LCD panel is a high
wipe gently with a soft cloth to prevent					technology product with resolution of two
scratching. Do not spray water or other					million to six million pixels. In a very few
liquids directly on the TV as electric shock					cases, you could see fine dots on the screen
may occur. Do not clean with chemicals					while you’re viewing the TV. Those dots
such as alcohol, thinners or benzine.					are deactivated pixels and do not affect the
yyMoving					performance and reliability of the TV.
Make sure the product is turned off,					yyGenerated Sound
unplugged and all cables have been					“Cracking” noise: A cracking noise that
removed. It may take 2 or more people to					occurs when watching or turning off the TV
carry larger TVs. Do not press or put stress					is generated by plastic thermal contraction
on the front panel of the TV.					due to temperature and humidity. This noise
yyVentilation					is common for products where thermal
Install your TV where there is proper					deformation is required.
ventilation. Do not install in a confined					Electrical circuit humming/panel buzzing: A
space such as a bookcase. Do not cover the					low level noise is generated from a high-
product with cloth or other materials while					speed switching circuit, which supplies a
plugged. Do not install in excessively dusty					large amount of current to operate a product.
places.					It varies depending on the product.
yyIf you smell smoke or other odors coming					This generated sound does not affect the
from the TV, unplug the power cord and					performance and reliability of the product.
contact an authorized service center.					yyTake care not to touch the ventilation
yyDo not press strongly upon the panel with a					openings. When watching the TV for a long
hand or a sharp object such as a nail, pencil					period, the ventilation openings may become
or pen, or make a scratch on it.					hot. This does not affect the performance of
yyKeep the product away from direct sunlight.					the product or cause defects in the product.
					yyIf the TV feels cold to the touch, there may
					be a small “flicker” when it is turned on. This
					is normal, there is nothing wrong with TV.
					Some minute dot defects may be visible on
yyNever touch this apparatus or antenna during					the screen, appearing as tiny red, green, or
a thunder or lightning storm.					blue spots. However, they have no adverse
yyWhen mounting a TV on the wall, make sure					effect on the TV’s performance. Avoid
not to install the TV by hanging the power					touching the LCD screen or holding your
and signal cables on the back of the TV.					finger(s) against it for long periods of time.
yyDo not allow an impact shock or any objects					Doing so may produce some temporary
to fall into the product, and do not drop					distortion effects on the screen.
anything onto the screen.

ENGLISH

ENGLISH

6 IMPORTANT SAFETY INSTRUCTIONS

DISPOSAL (Hg lamp only used in LCD TVs)

The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority.

Preventing “Image burn” or “Burn-in” on your TV screen

yyIf a fixed image displays on the TV screen for a long period of time, it will be imprinted and become a permanent disfigurement on the screen. This is “image burn” or “burn-in” and not covered by the warranty.

yyIf the aspect ratio of the TV is set to 4:3 for a long period of time, image burn may occur on the letterboxed area of the screen.

yyAvoid displaying a fixed image on the TV screen for a long period of time (2 or more hours for LCD, 1 or more hours for the Plasma TV) to prevent image burn.

	IMPORTANT SAFETY INSTRUCTIONS 7
For USA and Canada	Additional information of the
	manual

FCC NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and the receiver.

-Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Viewing the owner's manual

The owner’s manual in PDF file format is supplied on the enclosed CD. Install the Adobe Acrobat Reader to view the owner’s manual on your PC.

1Insert the supplied CD.

The web page appears automatically.

2Click Owner’s Manual on the web page.

3View the owner’s manual.

NOTE

web page does not appear automatically, access My computer and then click LG and index.html to view the owner’s manual.

NOTE TO CABLE/TV INSTALLER

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

ENGLISH

ENGLISH

8 TABLE OF CONTENTS

TABLE OF CONTENTS

2 IMPORTANT SAFETY INSTRUCTIONS

7Additional information of the manual

8TABLE OF CONTENTS

9INSTALLATION PROCEDURE

9	ASSEMBLING AND PREPARING
9	Unpacking
16	Parts and buttons

20Lifting and moving the TV

21Setting up the TV

21 - Attaching the stand

29 - Mounting on a table

31- Mounting on a wall

32- Tidying cables

33MAKING CONNECTIONS

33Connecting to an antenna or cable

34Connecting to a HD receiver, DVD, or VCR player

34- HDMI Connection

35- Component Connection

36- Composite Connection

37Connecting to a PC

37- HDMI Connection

38Connecting to an Audio System

38- Digital Optical Audio Connection

39Connecting to a USB

40 REMOTE CONTROL

42 WATCHING TV

42Connecting to the AC/DC adapter

42Turning the TV on for the first time

43TROUBLESHOOTING

43OPEN SOURCE SOFTWARE NOTICE

44SPECIFICATIONS

NOTE

yyImage shown may differ from your TV. yyYour TV’s OSD (On Screen Display) may differ slightly from that shown in this

manual.

yyThe available menus and options may differ from the input source or product model that you are using.

yyNew features may be added to this TV in the future.

INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING 9

INSTALLATION PROCEDURE

1Open the package and make sure all the accessories are included.

2Attach the stand to the TV set.

3Connect an external device to the TV set.

ASSEMBLING AND PREPARING

Unpacking

Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and item.

CAUTION

yyDo not use any unapproved items to ensure the safety and product life span.

yyAny damages or injuries by using unapproved items are not covered by the warranty. yyIn case of some model, the thin film on screen is a part of TV, So don’t take it off. yyPower Cord Installation Guide

-If the power cord provided with the TV looks like the below picture, please ensure that it is inserted in the correct direction.

TV

Power Cord

Correct

Wrong

NOTE

yyThe items supplied with your product may vary depending on the model.

yyProduct specifications or contents of this manual may be changed without prior notice due to upgrade of product functions.

yyFor an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm (0.39 inches) thick and 18 mm (0.7 inches) width.

yyUse an extension cable that supports USB 2.0 if the USB cable or USB memory stick does not fit into your TV's USB port.

AA

ENGLISH

*A 10 mm (0.39 inches) *B 18 mm (0.7 inches)

10 ASSEMBLING AND PREPARING

For CS460, CS461, LS3400, LS3410 series

Remote control,					Owner’s manual,				Power Cord
Batteries (AAA)					CD manual
(See p.40)

Stand Body	Stand Base	Stand Screws
(See p.21)	(See p.21)	8 EA, M4 x 20
		(See p.21)

ENGLISH

Protection cover		Desk-mount Screw
(See p.28)		(See p.29)

ASSEMBLING AND PREPARING 11

For LS3450 series

Remote control,					Owner’s manual,				Power Cord
Batteries (AAA)					CD manual
(See p.40)
(for 32LS3450)					(for 42LS3450)

Stand Body / Stand Base		Stand Body / Stand Base		Desk-mount Screw
(See p.22)		(See p.23)		(See p.29)
(for 32LS3450)		(for 42LS3450)

Stand Screws		Stand Screws		Cable holder
2 EA, P4 x 16		4 EA, P4 x 16		(See p.32)
4 EA, M4 x 20		4 EA, M4 x 14
(See p.22)		(See p.23)
(for 32LS3450)

Protection cover

(See p.28)

ENGLISH

12 ASSEMBLING AND PREPARING

For CS530, CS560 series

Remote control,					Owner’s manual,				Power Cord
Batteries (AAA)					CD manual
(See p.40)

Stand Body	Stand Base	Stand Screws
(See p.24)	(See p.24)	8 EA, M4 x 20
		(See p.24)

ENGLISH

Protection cover		Desk-mount Screw
(See p.28)		(See p.29)

ASSEMBLING AND PREPARING 13

For 22/26LS3500, 22/26LS3510

Remote control,	Owner’s manual,	Power Cord
Batteries (AAA)	CD manual
(See p.40)
		(For 22LS3500, 22LS3510)

Stand Body		Stand Base		Stand Screws
(See p.25)		(See p.25)		2 EA, P4 x 16
				(See p.25)
(For 26LS3500, 26LS3510)

Stand Screws		Cable holder		AC/DC Adapter
2 EA, M4 x 14		(See p.32)
(See p.25)

ENGLISH

ENGLISH

14 ASSEMBLING AND PREPARING

For 32LS3500, 32LS3510

Remote control,					Owner’s manual,				Power Cord
Batteries (AAA)					CD manual
(See p.40)

Stand Body		Stand Base		Stand Screws
(See p.26)		(See p.26)		4 EA, P4 x 16
				4 EA, M4 x 14
				(See p.26)

Desk-mount Screw		Cable holder
(See p.29)		(See p.32)

ASSEMBLING AND PREPARING 15

For 47LS4500, 55LS4500

Remote control,					Owner’s manual,				Wall Mount Inner Spacers
Batteries (AAA)					CD manual				4 EA
(See p.40)									(See p.31)

Stand Body		Stand Base		Stand Screws
(See p.27)		(See p.27)		8 EA, M4 x 20
				(See p.27)
(for 47LS4500)

Desk-mount Screw		Cable holder		Power Cord
(See p.29)		(See p.32)

ENGLISH