<![endif]>ENGLISH
LED LCD MONITOR
Please read this manual carefully before operating your set and retain it for future reference.
LED LCD MONITOR MODEL
22EB23PM
www.lg.com
<![endif]>ENGLISH
2 TABLE OF CONTENTS
3 |
ASSEMBLING AND PREPAR- |
21 |
FUNC. Setting |
||
|
ING |
21 |
-Picture Mode |
||
3 |
Unpacking |
22 |
-SUPER ENERGY SAVING |
||
23 |
-DUAL DISPLAY |
||||
4 |
Parts and buttons |
||||
23 |
-DUAL WEB |
||||
5 |
Setting up the Monitor set |
||||
24 |
-MY KEY Setting |
||||
5 |
- Attaching the Stand Base |
||||
|
|
|
|||
5 |
- Detaching the stand base |
|
25 TROUBLESHOOTING |
||
6 |
- Detaching the stand body |
|
6- Using the cable holder
7 |
- Mounting on a table |
27 |
SPECIFICATIONS |
|
7 |
- Adjusting the angle |
|||
27 |
22EB23PM |
|||
8 |
- Adjusting the stand height |
|||
8 |
- Using the Kensington locking device |
28 |
Preset Modes (Resolution) |
|
9 |
- Swivel stand |
28 |
Indicator |
9- Using the Pivot function
10 - Mounting on a wall |
|
29 |
PROPER POSTURE |
|
|
|
|||
11 |
USING THE MONITOR SET |
29 |
Proper posture for using the Monitor set. |
|
|
|
|
11 Connecting to a PC
11 - D-SUB connection
11 - DVI-D connection
13- Peripheral device connection
14CUSTOMIZING SETTINGS
15Customizing Settings
15- Menu Settings
16-Picture
17-Color
18-Display
19-Others
20MY KEY Setting
ASSEMBLING AND PREPARING 3
Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories.
<![endif]>ENGLISH
CD(Owner's Manual) / |
D-SUB Cable |
|
(This cable is not included in all |
||
Card |
||
countries.) |
||
|
DVI-D Cable
(This cable is not included in all countries.)
Power Cord |
Stand Base |
One Screw |
Cable Holder |
CAUTION
yyDo not use any unapproved accessories to ensure the safety and product life span.
yyAny damages or injuries by using unapproved accessories are not covered by the warranty.
NOTE
yyThe accessories supplied with your product may vary depending on the model.
yyProduct specifications or contents in this manual may be changed without prior notice due to upgrade of product functions.
4 ASSEMBLING AND PREPARING
<![endif]>ENGLISH
Power Indicator yyLED On : Power is on yyLED Off: Power is off
(Power Button)
Front Side Buttons
Input Connectors (See p. to 13)
ASSEMBLING AND PREPARING 5
1Place the Monitor set with the screen side down on a flat and cushioned surface.
CAUTION
yyTo protect the screen from scratches, cover the surface with a soft cloth.
2Check the position (at the front and rear) of the stand body, then mount the stand base on the stand body as shown in the figure.
Stand Body
Stand Base
3Using a coin, turn the screw clockwise to secure the stand base.
Stand Base
1Place the monitor's screen face down.
To protect the screen from scratches, cover the surface with a soft cloth.
2Using a coin, turn the screw in the stand base counterclockwise. Detach the stand base from the stand body.
Stand Body
Stand Base
CAUTION
yyThe components appearing in the illustrations may look different from the actual product.
yyDo not carry the monitor upside-down as this may cause it to fall off its stand, resulting in damage or injury.
yyTo avoid damaging the screen when lifting or moving the monitor, only hold the stand or the plastic cover. This avoids putting unnecessary pressure on the screen.
yyOnly remove the tape and the locking pin when the monitor is mounted on the stand base and is in an upright position. Otherwise, the stand body may protrude, which may lead to injury.
<![endif]>ENGLISH
6 ASSEMBLING AND PREPARING
<![if ! IE]> <![endif]>ENGLISH |
1 |
Place the monitor's screen face down. To |
|
||
|
|
protect the screen from scratches, cover the |
|
|
surface with a soft cloth. |
|
2 |
Using a screwdriver, remove the four screws |
|
|
and detach the stand from the monitor. |
1Fix the Knob (Cable holder) to the Hole(Hingebody).
2Use one screw to fix the Cable Holder and monitor set.
3 Close the Cable holder.
ASSEMBLING AND PREPARING 7
1Lift the monitor and place it on the table in an upright position.
Install at least 10 cm away from the wall to ensure sufficient ventilation.
10 cm
10 cm
10 cm
10 cm
1Place the monitor mounted on the stand base in an upright position.
2Adjust the angle of the screen. The angle of the screen can be adjusted up to 5° forwards and 20° backwards for a comfortable viewing experience.
Rear Side |
Front Side |
<![endif]>ENGLISH
21 Connect the Power cord to the monitor, then plug the power cord into the wall outlet. (Before connect please check the “ON/OFF” knob in “O” state).
2Press the “ON/OFF” knob in “ ” state (Open the power).
3Press the (Power) button on the front of the monitor to turn on the monitor.
CAUTION
yyUnplug the power cord prior to moving or installing the monitor. There is risk of electric shock.
WARNING
yyTo avoid injury to the fingers when adjusting the screen, do not hold the lower part of the monitor's frame as illustrated below.
yyBe careful not to touch or press the screen area when adjusting the angle of the monitor.
<![endif]>ENGLISH
8 ASSEMBLING AND PREPARING
1Place the monitor mounted on the stand base in an upright position.
2Remove the tape attached at the bottom rear of the stand body, then pull out the locking pin.
Stand Body
Tape
Locking Pin
3 The height can be adjusted up to 120 mm.
120.0mm
CAUTION
yyOnce the pin is removed, it is not necessary to re-insert it to adjust the height.
The connector for the Kensington lock is located on the rear of the monitor.
For more information on installation and usage, refer to the Kensington lock user manual or visit the website at http://www.kensington.com.
Connect the monitor to the table with the Kensington lock cable.
NOTE
yyUsing the Kensington lock is optional. The accessories can be purchased at your local electronics store.
WARNING
yyDo not put your finger between the screen and the base (chassis) when adjusting the screen's height.
|
|
ASSEMBLING AND PREPARING 9 |
||
|
|
|
|
|
Swivel stand |
3 Be careful with the cables when rotating the |
|||
yyImage shown may differ from your Monitor |
screen. |
|||
|
|
|
|
|
set. |
|
|
|
|
1Swivel 355 degrees and adjust the angle of the Monitor set to suit your view.
The pivot function allows you to rotate the screen 90 degrees clockwise.
1 Lift the monitor to its highest height to utilize the Pivot function.
2Landscape & Portrait : You can rotate the panel 90° clockwise. Please be cautious and avoid contact between the monitor head and the Stand Base when rotating the screen to access the Pivot function. If the monitor head touches the Stand Base, then the Stand Base could crack.
Head section
<![endif]>ENGLISH
Stand section