Colour Television
OWNER’S MANUAL
Please read this manual carefully before operating your set. Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote this information to your dealer when you require service.
Model number |
: |
Serial number |
: |
P/NO : MFL51232838-EN (CW81A/B)
Installation
Power
This set operates on an AC mains supply, the voltage is as indicated on the label on the back cover.
Never apply DC power to the set. In the event of thunderstorms or powercuts, please pull out the
aerial and mains plugs.
Press the POWER button on the front panel or side panel to turn off the TV when the TV set is not being used for a long time.It is recommended to remove the plug from the wall outlet(Power point).
Disconnecting device from mains
Mains plug is the disconnecting device. The plug must remain readily operable
Warning
To prevent fire or shock hazard, do not expose the set to rain or moisture.
Do not place anything containing liquid on top of the set, this may cause a fire or could give an electric shock.
Service
Never remove the back cover of the set as this can expose you to very high voltage and other hazards. If
the set does not operate properly, unplug it and call your dealer.
Aerial
Connect the aerial cable to the socket on the back cover. For the best reception an outdoor aerial should be used.
Location
Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to expose the set to any unnecessary vibration, moisture, dust or heat. Also ensure that the set is placed in a position to allow a free flow of air. Do not cover the ventilation openings on the back cover.
Note (option):
To remove dirt or fingerprint on the surface of your
TV, please rub with a line-free cloth supplied in the accessory.Do not pose too much pressure in cleaning so as to prevent any risk of damage to the product.
Connection of external equipment
Aerial socket
1.Connect the RF out socket of the VCR to the aerial socket on the back of the set.
2.Connect the aerial cable to the RF aerial in socket of the VCR.
3.Store the VCR channel on a desired programme number using the ‘Manual programme tuning’ section.
4.Select the programme number where the VCR channel is stored.
5.Press the PLAY button on the VCR.
Audio/Video in/out sockets (option)
1.Connect the audio/video out sockets of the VCR to audio/video in sockets of the set and in sockets of the VCR to RF OUT sockets of the set.
2.If the VCR is connected to the AV sockets on the set, press the TV/AV button to select AV1 or AV2.
3.Press the PLAY button on the VCR.The VCR playback picture appears on the screen.
You can also record programmes received by the TV on video tape via audio/video out sockets.
Note : If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO socket of the set.
Euro scart socket (option)
1.Connect the Euro scart socket of the VCR to the Euro scart socket of the set.
2.Press the PLAY button on the VCR.
If your VCR outputs a switching voltage when connected to Euro scart socket, the set will switch to AV 1 mode automatically. But if you
want to keep on watching TV mode, press the D / E or NUMBER buttons.Otherwise press the TV/AV button on the remote control handset to select AV 1 The VCR playback picture appears on the screen.
You can also record programmes received by the
TV on video tape.
Note : Signal type RGB, i.e. the signals red, green and blue can only be selected for the Euro scart socket. These signals are transmitted, for example, by a pay TV decoder, game machine or photo CD unit, etc.
Component in sockets (option)
1.Connect the COMPONENT video output sockets (Y Cb Cr, Y Pb Pr or Y B-Y R-Y) of the
COMPONENT (480i) to the COMPONENT
INPUT sockets (Y PB PR) on the set.
2.Connect the audio cable from the COMPO-
NENT to AUDIO IN sockets of AV IN2.
3.Press the TV/AV button to select COMPONENT.
4.Press the PLAY button on the COMPONENT.
The COMPONENT playback picture appears on the screen.
Headphone socket (option)
You can listen to the sound through the headphones. To adjust the headphone volume, press
the F / G button.
If you press the MUTE button, the sound from the headphone’s is switched off.
Location and function of controls
Battery installation |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The remote control handset is powered by AAA |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
type batteries.Install batteries as indicated by the |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
polarity symbols ( + and - ) marked inside the |
|
|
|
|
|
|
|
|
|
|
|
|
or |
|
|
|
|
|
|
|
|
|
|
|
|
compartment. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Note : To avoid damage from possible battery |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
leakage, remove the batteries if you do not plan to |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
use the remote control handset for an extended |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
period of time |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2
Location and function of controls
Remote control handset
Before you use the remote control handset, please install the batteries. See the next page.
1
2
3
4
12
5
6
7
1. POWER
POWER MUTE
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
9 |
MENU |
0 |
TV/AV |
|
PR |
|
VOL |
OK |
VOL |
Q. |
PR |
|
|
LIST |
|
VIEW |
|
|
SLEEP |
EYE/ |
I/II/ |
FAVOURITE |
FM |
|
9
10
13
11
8
switches the set on from standby or off to standby.
2.NUMBER BUTTONS
Switches the set on from standby or directly select a number.
3.MENU
selects a menu.
4.D / E (Programme Up/Down) selects a programme or a menu item. switches the set on from standby.
scans programmes automatically.
F / G (Volume Up/Down) adjusts the volume. adjusts menu settings.
OK
accepts your selection or displays the current mode.
5.SLEEP
sets the sleep timer.
6.FAVOURITE
selects a favorite programme.
7.FM BUTTON
Select the FM Radio mode.
8.EYE/* (option)
switches the eye function on or off.
9.MUTE
switches the sound on or off.
10.TV/AV
selects TV or AV mode.
switches the set on from standby. exits the Teletext mode.
11.I/II/*
selects the language during dual language broadcast.
selects the sound output (option).
12.Q.VIEW (or YELLOW)
returns to the previously viewed programme.
13.LIST (or BLUE)
displays the programme table.
* : No function
COLOURED BUTTONS : These buttons are used for teletext (only TELETEXT models) or programme edit.
Front panel
MAIN POWER (ON/OFF) switches the set on or off.
POWER/STANDBY INDICATOR
illuminates brightly when the set is in standby mode.dims when the set is switched on.
REMOTE CONTROL SENSOR
Note : Only use the supplied remote control handset. (When you use others, they will not be able to function.)
MENU
selects a menu.
OK
accepts your selection or displays the current mode.
F / G (Volume Down/Up) adjusts the volume. adjusts menu settings.
D / E (Programme Up/Down) selects a programme or a menu item. switches the set on from standby.
3
Loading...