KITCHENAID KP25M0XMC, KP25M0XAQ, KP25M0XBM, KP25M0XER, KP25M0XVB Owner's Manual

Stand Mixer - Bowl Lift

PARTS AND FEATURES

RESET
OFF/0 STIR 2	4	6	8	10

6

8

19

1 2

3 7 4

18 5

9
10		12
11
13	14	15	16	17

	1						11
		Motor Head						Bowl*
	2	Attachment Hub					12	Bowl Handle*
	3	Attachment Knob					13	Flex Edge Beater**
	4	Hinged Hub Cover					14	Flat Beater**
	5	Beater Shaft					15	Spiral Dough Hook**
	6	Speed Control					16	Wire Whip**
	7	Bowl Lift Lever					17	11-Wire Stainless Steel Elliptical
	8	Beater Height Adjustment Screw						Whip**
							18	Pouring Shield**
	9	Bowl Support
							19	Spring Latch and Bowl Pin
	10	Locating Pins
								(Not Shown)

*Bowl type may vary. Bowls are also available for purchase as separate accessories. **Included with select models. Picture/Style may vary from product depending on model.

2

PRODUCT SAFETY

<![if ! IE]> <![endif]>ENGLISH

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed, including the following:

1.Read all instructions.

2.To protect against the risk of electrical shock do not put Stand Mixer in water or other liquid.

3.This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they are closely supervised and instructed concerning the use of the appliance by a person responsible for their safety. Close supervision is necessary when any appliance is used by or near children. Children should be supervised to ensure that they do not play with the appliance.

4.Turn the appliance OFF, then unplug from the outlet when not in use, before assembling or disassembling parts and before cleaning. To unplug, grasp the plug and pull from the outlet. Never pull from the power cord.

5.Avoid contacting moving parts. Keep hands, hair, and clothing, as well as spatulas and other utensils, away from beater during operation to reduce the risk of injury to persons and/or damage to the Stand Mixer.

6.Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Contact the manufacturer at their customer service telephone number for information on examination, repair, or adjustment.

7.The use of accessories or attachments not recommended or sold by the manufacturer may cause fire, electric shock or injury.

8.Do not use the Stand Mixer outdoors.

9.Do not let the cord hang over the edge of table or counter.

10.Remove the flat beater, wire whip, or spiral dough hook from the Stand Mixer before washing.

SAVE THESE INSTRUCTIONS

This product is designed for household use only.

3

PRODUCT SAFETY

ELECTRICAL REQUIREMENTS

		Voltage: 120 V
	WARNING
		Frequency: 60 Hz
		NOTE: The power rating for your Stand
		Mixer is printed on the serial plate.
		Do not use an extension cord. If the
		power supply cord is too short, have a
		qualified electrician or service person
	Electrical Shock Hazard	install an outlet near the appliance.
		The maximum rating is based on the
	Plug into a grounded 3 prong	attachment that draws the greatest
	outlet.	load (power). Other recommended
	Do not remove ground prong.	attachments may draw significantly less
		power.
	Do not use an adapter.
	Do not use an extension cord.
	Failure to follow these instructions
	can result in death, fire, or
	electrical shock.

ACCESSORY GUIDE

	Accessory	Use to mix	Description
	Flat beater*	Normal to heavy	Cakes, creamed frostings, candies,
			cookies, biscuits, pie pastry, meat loaf,
	Flex Edge Beater*	mixtures
			mashed potatoes
	Spiral Dough Hook*	Mixing and	Breads, rolls, pizza dough, coffee cakes
		kneading yeast
			buns
		doughs
	Wire Whip*	Mixtures	Eggs, egg whites, heavy cream,
		that need air	boiled frostings, sponge cakes,
	11-Wire Elliptical Whip*
		incorporated	mayonnaise, some candies

*Available as an accessory purchase with selected models only.

4

SPEED CONTROL GUIDE

All speeds features Soft Start® which allows the Stand Mixer to start at a lower speed to help avoid ingredient splash-out and “flour puff” at start-up, then increases to the selected speed.

The speed control can be set between the speeds listed in the chart to obtain speeds 1, 3, 5, 7, and 9 if a finer adjustment is required.

<![if ! IE]>

<![endif]>ENGLISH

	Speed	Accessory	Action	Description
				For slow stirring, combining, mashing, and
		Flat Beater		starting all mixing procedures. Use to add
	Stir		Stirring	flour and dry ingredients to batter, and
		Flex Edge Beater
				add liquids to dry ingredients. Do not use
				STIR speed to mix or knead yeast doughs.
				For slow mixing, mashing, and faster
		Flat Beater		stirring. Use to mix and knead yeast
			Slow mixing,	doughs, heavy batters, and candies; start
	2	Flex Edge Beater
			Kneading	mashing potatoes or other vegetables; cut
		Spiral Dough Hook
				shortening into flour; mix thin or splashy
				batters.
				For mixing semi-heavy batters, such
		Flat Beater		as cookies. Use to combine sugar and
				shortening and to add sugar to egg whites
		Flex Edge Beater	Mixing,
	4			for meringues. Medium speed for cake
		Wire Whip	beating
				mixes. Use with: food grinder, rotor slicer/
		11-Wire Elliptical Whip
				shredder, pasta roller, and fruit/vegetable
				strainer.
		Flat Beater		For medium-fast beating (creaming) or
	6	Flex Edge Beater	Beating,	whipping. Use to finish mixing cake,
		Wire Whip	creaming	doughnut, and other batters. High speed
		11-Wire Elliptical Whip		for cake mixes.
				For whipping cream, egg whites, and
	8-10	Wire Whip	Fast beating,	boiled frostings. For whipping small
		11-Wire Elliptical Whip	Whipping	amounts of cream, egg whites, or for final
				whipping of mashed potatoes.

NOTE: Use Speed 2 to mix or knead yeast doughs. Use of any other speed creates high potential for Stand Mixer failure. The PowerKnead™ spiral dough hook efficiently kneads most yeast dough within 4 minutes.

Capacity Chart

	5-5.5 Quart	6-6.5 Quart	7-7.5 Quart
Cookies	9-10 dozen	13 dozen	14 dozen

5

PRODUCT ASSEMBLY

1

RESET
OFF/0	STIR 2	4	6	8	10

Turn the Stand Mixer to “OFF/ 0” and then unplug.

2

Spring latch

Locating pin

To attach the bowl: Fit the bowl supports over locating pins and press down on back of the bowl until bowl pin snaps into spring latch.

IMPORTANT: If the bowl is not securely snapped into place, it will be unstable and wobble during use.

3

Pin

To attach the accessory: Slip the accessory onto the shaft. Turn to hook it over the pin on the shaft.

4

To raise the bowl: Rotate the bowl lift lever to the straight up position. The bowl must always be in the raised position when mixing.

6

PRODUCT ASSEMBLY

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

5

Test the beater to bowl clearance: Plug the Stand Mixer into a grounded 3 prong outlet. Turn Stand Mixer ON and test each speed, making sure the beater does not touch the bowl during operation.

If the beater is too far away from the bottom or is hitting the bowl, proceed to next step to make adjustments.

6

Raise Bowl	Lower Bowl

(OPTIONAL) To adjust beater to bowl clearance: Lower the bowl to the down position. Turn the screw slightly

counterclockwise (left) to raise the beater, or clockwise (right) to lower it. Adjust the beater so that it just clears the surface of the bowl. Check again the clearance of the beater to the bowl.

IMPORTANT: When properly adjusted, the flat beater will not strike on the bottom or sides of the bowl. If the flat beater or the wire whip is so close that it strikes the bottom of the bowl, coating may wear off the beater or wires on the whip may wear.

<![if ! IE]>

<![endif]>ENGLISH

7

PRODUCT ASSEMBLY

USING THE POURING SHIELD*

Use the pouring shield to avoid having ingredients splashing out of the bowl when mixing, as well as to easily pour ingredients into the bowl while mixing.

1

To attach the pouring shield*: Slide the pouring shield from the front of the Stand Mixer over the bowl. The bottom rim of the pouring shield* fits inside of the bowl.

2

Pour the ingredients into the bowl through the pouring chute.

*Available with select models only and available as an accessory purchase.

8

PRODUCT USAGE

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

WARNING

Injury Hazard

Unplug mixer before touching beaters.

Failure to do so can result in broken bones, cuts, or bruises.

<![if ! IE]>

<![endif]>ENGLISH

1

RESET
OFF/0 STIR 2	4	6

Plug the Stand Mixer into a grounded 3 prong outlet. Start with lower speed to avoid splashing and increase it gradually. Refer to the “Speed Control Guide”.

2

Do not scrape the bowl while operating. Scraping the bowl once or twice during mixing is usually sufficient.

9

PRODUCT USAGE

OPTIONAL ATTACHMENTS

KitchenAid® offers a wide range of optional attachments such as the Spiralizer, Pasta Cutters, or Food Grinder that may be attached to the Stand Mixer attachment power hub.

1

2

RESET OFF/0

STIR 2

4

6

8

10

Turn the Stand Mixer to “OFF/ 0” and then unplug.

Flip up hinge attachment hub cover to open.

3

Insert attachment into attachment hub, making certain that attachment power shaft fits into the square attachment hub socket.

4

Tighten the attachment knob by turning it clockwise until the attachment is secured to the Stand Mixer.

NOTE: See the Use and Care Guide of each specific attachment for more details.

10

PRODUCT DISASSEMBLY

1

2

RESET
OFF/0 STIR 2	4	6	8	10

	Turn the Stand Mixer to “OFF/ 0” and	Remove Pouring shield: Lift the front of
		the pouring shield* clear of the rim of the
	then unplug.
		bowl. Pull away from the Stand Mixer.

3

4

Remove the accessory: Press accessory	To Remove Bowl: Place bowl-lift lever in
upward and turn to the left. Pull down the	the down position. Grasp bowl handle
accessory from beater shaft.	and lift straight up and off locating pins

<![if ! IE]>

<![endif]>ENGLISH

11

CARE AND CLEANING

IMPORTANT: Do not immerse the Stand Mixer body in water or other liquids.

1

2

RESET OFF/0

STIR 2

4

6

8

10

Turn the Stand Mixer to “OFF/ 0” and then unplug.

Wipe the Stand Mixer body with a soft, damp cloth.

3

The following parts are dishwasher-safe, top rack only: Bowl, Flat beater, Flex edge beater*, Spiral dough hook, 11 wire elliptical whip* and Pouring shield*.

4

The following part should be hand-washed only, using warm, soapy water and drying thoroughly: Wire whip only.

FOR DETAILED INFORMATION OF THE STAND MIXER

Visit www.kitchenaid.com/quickstart for additional instructions with videos, inspiring recipes, and tips on how to use and clean your Stand Mixer and accessories.

*Available with select models only and available as an accessory purchase.

12

TROUBLESHOOTING GUIDE

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

	Problem	Solution
	If Stand Mixer warms up during	Under heavy loads with extended mixing time periods, you
		may not be able to comfortably touch the top of the Stand
	use:	Mixer. This is normal.
	If Stand Mixer emits a pungent	This is normal. This is common with electric motors.
	odor during initial use:
	If the flat beater hits the bowl:	Stop the Stand Mixer. See the “Product Assembly” section
		and adjust the beater to bowl clearance.
	The speed control lever does	To move the speed control lever with ease, lift slightly up
	not move smoothly or easily:	as you move it across the settings in either direction.
		Is the Stand Mixer plugged in?
		Is the fuse in the circuit to the Stand Mixer in working
	If your Stand Mixer should fail	order? If you have a circuit breaker box, be sure the circuit
	to operate, please check the	is closed.
	following:	Turn off the Stand Mixer for 10-15 seconds, then turn it
		back on. If the Stand Mixer still does not start, allow it to
		cool for 30 minutes before turning it back on.

Note: If the problem cannot be corrected, See the “Warranty and Service” section. Do not return the Stand Mixer to the retailer; retailers do not provide service.

<![if ! IE]>

<![endif]>ENGLISH

13

WARRANTY AND SERVICE

KITCHENAID® STAND MIXER WARRANTY FOR THE 50 UNITED STATES, THE DISTRICT OF COLUMBIA, PUERTO RICO, AND CANADA

This warranty extends to the purchaser and any succeeding owner for Stand Mixers operated in the 50 United States, the District of Columbia, Puerto Rico, and Canada.

Length of Warranty:	One Year Full Warranty from date of purchase.
KitchenAid Will Pay	Hassle-Free Replacement of your Stand Mixer. See
for Your Choice of:	the next page for details on how to arrange for
	service, or call the Customer eXperience Center
	toll-free at 1-800-541-6390.
	OR
	The replacement parts and repair labor costs to correct
	defects in materials and workmanship. Service must be
	provided by an Authorized KitchenAid Service Center.
KitchenAid Will	A. Repairs when your Stand Mixer is used in other
Not Pay for:	than normal single family home use.
	B. Damage resulting from accident, alteration,
	misuse or abuse.
	C. Any shipping or handling costs to deliver your
	Stand Mixer to an Authorized Service Center.
	D. Replacement parts or repair labor costs for
	Stand Mixer attachments operated outside the
	50 United States, District of Columbia, Puerto
	Rico, and Canada.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

IMPLIED WARRANTIES, INCLUDING TO THE EXTENT APPLICABLE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXCLUDED TO THE EXTENT LEGALLY PERMISSIBLE. ANY IMPLIED WARRANTIES THAT MAY

BE IMPOSED BY LAW ARE LIMITED TO ONE YEAR, OR THE SHORTEST PERIOD ALLOWED BY LAW. SOME STATES AND PROVINCES DO NOT ALLOW LIMITATIONS OR EXCLUSIONS ON HOW LONG AN IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.

IF THIS PRODUCT FAILS TO WORK AS WARRANTED, CUSTOMER’S SOLE AND EXCLUSIVE REMEDY SHALL BE REPAIR OR REPLACEMENT ACCORDING TO THE TERMS OF THIS LIMITED WARRANTY. KITCHENAID AND KITCHENAID CANADA DO NOT ASSUME ANY RESPONSIBILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. This warranty gives you specific legal rights and you may also have other rights which vary from state to state or province to province.

14

WARRANTY AND SERVICE

HASSLE-FREE REPLACEMENT WARRANTY—50 UNITED STATES, DISTRICT OF COLUMBIA, AND PUERTO RICO

We’re so confident the quality of our products meets the exacting standards of KitchenAid that, if your Stand Mixer should fail within the first year of ownership, KitchenAid will arrange

to deliver an identical or comparable replacement to your door free of charge and arrange to have your original Stand Mixer returned to us. Your replacement unit will also be covered by our one year limited warranty.

If your Stand Mixer should fail within the first year of ownership, simply call our

toll-free Customer eXperience Center at 1-800-541-6390 Monday through Friday. Please have your original sales receipt available when you call. Proof of purchase will be required to initiate the claim. Give the consultant your complete shipping address (no P.O. Box numbers, please).

When you receive your replacement Stand Mixer, use the carton, packing materials, and prepaid shipping label to pack up your original Stand Mixer and send it back to KitchenAid.

HASSLE-FREE REPLACEMENT WARRANTY—CANADA

We’re so confident the quality of our products meets the exacting standards of the KitchenAid brand that, if your Stand Mixer should fail within the first year of ownership, we will replace your Stand Mixer with an identical

or comparable replacement. Your replacement unit will also be covered by our one year limited warranty.

If your Stand Mixer should fail within the first year of ownership, simply call

our toll-free Customer eXperience Center

at 1-800-807-6777 Monday through Friday. Please have your original sales receipt available when you call. Proof of purchase will be required to initiate the claim. Give the consultant your complete shipping address.

When you receive your replacement Stand Mixer, use the carton, packing materials, and prepaid shipping label to pack up your original Stand Mixer and send it back to KitchenAid.

ARRANGING FOR SERVICE AFTER THE WARRANTY EXPIRES, OR ORDERING ACCESSORIES AND REPLACEMENT PARTS

In the United States and Puerto Rico:

For service information, or to order accessories or replacement parts, call toll-free at 1-800-541-6390 or write to:

Customer eXperience Center,

KitchenAid Small Appliances,

P.O. Box 218, St. Joseph, MI 49085-0218

Outside the United States and Puerto Rico:

Consult your local KitchenAid dealer or the store where you purchased the Stand Mixer for information on how to obtain service.

For service information in Canada:

Call toll-free 1-800-807-6777.

For service information in Mexico: Call toll-free 01-800-0022-767.

<![if ! IE]>

<![endif]>ENGLISH

®/™ ©2019 KitchenAid. All rights reserved. KITCHENAID and the design of the stand mixer are trademarks in the U.S. and elsewhere. Used under license in Canada.

15

PIÈCES ET CARACTÉRISTIQUES

RESET
OFF/0 STIR 2	4	6	8	10

6

8

19

1 2

3 7 4

18 5

9
10		12
11
13	14	15	16	17

	1						11
		Tête du moteur						Bol*
	2	Prise à accessoires					12	Poignée du bol*
	3	Bouton à accessoires					13	Fouet à côté souple**
	4	Couvercle à charnière de la prise					14	Fouet plat**
	5	Arbre du fouet					15	Crochet pétrisseur en spirale**
	6	Commande de vitesse					16	Fouet métallique**
	7	Levier lève-bol					17	Fouet elliptique en acier inoxydable
	8	Vis de réglage de la hauteur du fouet						à 11 fils métalliques**
							18	Écran verseur**
	9	Support du bol
							19	Loquet à ressort et piton du bol
	10	Goupilles de positionnement
								(non illustrés)

*Le type de bol peut varier. Les bols sont également offerts à l’achat comme accessoires séparés.

**Compris avec certains modèles. Selon le modèle/style, l’illustration peut varier du produit réel.

16