Futaba R7014SB User Manual

1M23N32201

R7014SB	FASSTest-2.4GHz Bidirectional Communication System / FASST-Multi-ch 2.4GHz
	S.BUS2 / S.BUS Port and 12 Channels (+DG1,2) for Conventional System Receiver

Thank you for purchasing a Futaba R7014SB FASSTest-2.4GHz compatible receiver. The R7014SB receiver features bi-directional communication with a FASSTest Futaba transmitter using the S.BUS2 port. Using the S.BUS2 port an impressive array of telemetry sensors may be utilized. It also includes both standard PWM output

ports and S.BUS output ports. The R7014SB can also be switched to the FASST-Multi-ch System.

● Applicablesystems:FutabaFASSTest-2.4GHz/FASST-Multi-chsystem transmitter

Usageprecaution

•Analog servos cannot be used with the R7014SB in the FASSTest 12CH mode.

•When the FASST Multi-ch High-speed Mode is used, analog servos cannot be used at the CH1 6 outputs for convention systems. How-

ever, in other than the FASSTest 12CH mode, analog servos can be used at CH7-12, DG1 and DG2 at any time.

•Don't connect to Extra Voltage Telemetry Port before turning on a receiver.

WARNING

Changes or modification not expressly approved by the party

responsible for compliance could void the user’ s authority to operate the equipment.

The R7014SB receiver should be protected from vibration by foam rubber, Velcro, or similar mounting methods. Protect from moisture.

Antennainstallationprecaution

Do not cut or bundle the receiver antenna wire.

Do not bend the coaxial cable. It causes damage.

The antennas must be mounted in such a way to assure they are strain relieved.

Keep the antenna as far away from the motor, ESC and other noise sources as you possibly can.

Be sure that the two antennas are placed at 90 degrees to each other.

■ The R7014SB has two antennas. In order to maximize signal reception and promote safe modeling Futaba has adopted a diversity antenna system. This allows

the receiver to obtain RF signals on both antennas and fly problem-free.

Antennainstallationforcarbonfuselage

You must leave 30mm at the tip of the antenna fully exposed. The

exposed antenna should be secured so that it cannot move around or back inside of your aircraft.

Becarefulofconnectorinsertion

Don't connect an S.BUS servo / gyro to S.BUS2 connector.

Do not connect the power supply battery to other than the power supply connector.

■ There is the danger of ignition, explosion, or burning.

Linkprecaution

Do not perform the linking procedure while the motor's main power is connected or the engine is operating as it may result in serious injury.

When the linking is complete, please cycle the receiver power and ensure the receiver is properly linked to the transmitter.

Please power up your system in this order. Transmitter first, followed by the receiver.

If the R7014SB receiver was previously linked to another transmitter, make sure that transmitter is not operating while linking the receiver to the new transmitter.

					The receiver power supply can			Connector
					be connected to any port.
								connectors of the
(Antenna installation)				Connection
						When all ports are used.		The direction of the
						Servo		bottom 3 ports is
			Antenna		Y-harness		Battery	different by 90˚.
						Switch	3.7 -7.4V
90˚
			R7014SB		Default : S.BUS port
					It's possible to change to DG2.
					S.BUS	Telemetry sensor
					DG2
					S.BUS2	Telemetry sensor
	Extra Voltage				Hub	S.BUS2equipment
	Telemetry Port				DG1
						R7014SBSpecifications
				Link/Mode	1-12
	Mode LED		Link LED		channel	FASSTest-2.4GHz system(14ch/12ch mode)
				switch		FASST-2.4GHz system (Multi-ch mode)
						S.BUS2 and S.BUS port and Linear 12ch +Digital 2ch for conventional system
					CH1-12 Servos	receiver
						• Dual antenna diversity
			LEDIndication			• Size: 1.5 x 2 x 0.6 in. (37.0x50.2x15.9mm)
						• Power requirement: 3.7V to 7.4V (Voltage range: 3.5 to 8.4V)
						• Weight: 0.7 oz. (20.8g)
System	ModeLED		Status		LinkLED	• Battery F/S Voltage: FASSTest:It sets up with a transmitter
						FASST: 3.8V *The Battery F/S voltage is set for 4-cell NiCd/NiMH battery.
	Green		Nosignalreception		RedSolid	Battery F/S function doesn't work properly when other type battery is used.
FASSTest			Receivingsignals		GreenSolid	• Extra Voltage port: 0V-70V DC
	Solid		Waitingforlink		Start → 2secondslater →	ComplianceInformationStatement(forU.S.A.)
					RedBlink 1second
			Nosignalreception
					RedSolid	This device complies with part 15 of the FCC Rules. Operation is subject to the following three con-
			Receivingsignals		GreenSolid	ditions:
FASST	Off					(1) This device may not cause harmful interference, and (2) This device must accept any interference
		ReceivingsignalsbutIDisunmatched			GreenBlink	(3) RF Exposure Information (SAR)
						received, including interference that may cause undesired operation.
			Waitingforlink		RedBlink	This device meets the government's requirements for exposure to radio waves. This device is de-
FASSTest						signed and manufactured not to exceed the emission limits for exposure to radio frequency (RF)
		Unrecoverableerror(EEPROM,etc.)			Alternateblink	energy set by the Federal Communications Commission of the U.S. Government. The exposure stan-
FASST						dard employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit
						set by the FCC is 1.6 W/kg. Tests for SAR are conducted using standard operating positions accepted
						by the FCC with the EUT transmitting at the specified power level in different channels.
						The FCC has granted an Equipment Authorization for this device with all reported SAR levels evalu-
						ated as in compliance with the FCC RF exposure guidelines. SAR information on this device is on
						file with the FCC and can be found under the Display Grant section of www.fcc.gov/eot/ea/fccid after
1.						searching on FCC ID: AZPR7014SB-24G
						The responsible party for the compliance of this device is:
2.						Futaba Service Center
						3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A
						TEL [phone] or E-mail: [e-mail] (Support)
						TEL [phone] or E-mail: [e-mail] (Service)