FeiYu Tech FY WGS User Manual

Page 1

Manual Version 1.0

FY WGS is a lightweight, yet feature-rich, wearable 3 axis gimbal capable of capturing immersive and fully stabilized footages. It is compatible with GoPro HERO4 Session and other cameras with the same dimensions.

The FY WGS is a miniaturized version of the best-selling FeiYu gimbal, offering exceptional stabilization technology in a wearable form factor for action cameras. A GoPro T-Clamp adapter is packaged with every FY WGS. Users can attach the gimbal to any accessories supporting the GoPro three-prong mount. The FY WGS also contains two 1/4" tripod mounts on its gimbal body, allowing the gimbal to be mounted in different orientations to all universal tripod screw mount accessories (including helmets, bikes, selfie sticks and other accessories).

Operation LED Status Function

* When the gimbal is in the Inverted Mode it will revert back to the original orientation after three press. When the battery is low, the gimbal will make three beeping sound and automatically shut down itself.

Turn On And Switch To The Mode’s LED Status

Turn Off After A moment

Power On

Shutdown

The LED light will flash distinctively to indicate different operating modes.

Switch between different operating modes by pressing the function button.

Remove the screws on the battery compartment, insert two16340 batteries and tighten the screws.

Mount the camera carefully to the mounting bracket and tighten the screws.

Function

Button

Function

Button

Operating Modes and Functions

Function Button

（

OFF

）

Tilting Axis

Rolling Axis

Panning Axis

Function Interface

1/4 Inch Screw Hole

Screws For The Battery Compartment

T-Clamp Screw Hole

Introduction

Install

Accessories

Operation

STEP 1

STEP 2 STEP 3

POWERING

ON / OFF

Use the 3M Adhesive to fix the bottom of the Gimbal. Use GoPro Accessories, mount the provided T-clamp to the side or the bottom of the gimbal. Attach T-clamp to any accessories supporting the standard GoPro three-prong mount. The gimbal can also be mounted directly to other accessories using the standard 1/4" tripod mount. Tighten all screws and ensure it is firmly mounted before using the gimbal.

USB CableUSB Connector

How to Charging

USB Cable

FY WGS 3 Axis Wearable Gimbal is compatible with Gopro HERO4 Session

Do not power on the gimbal before completing all the installation steps.

WARNING !WARNING !

Camera stays in its current orientation. All panning, tilting and rolls are restricted.

Mode #1 - Panning Mode

Camera is permitted to pan left or right. Vertical tilts or rolls are restricted.

Mode #2 - Panning and Tilng Mode Camera is permitted to pan left or right and tilt up and down. Rolls are restricted.

Mode #3 - Lock Mode

Inversion Mode

Pressing the function button three consecutive times in any operating mode, the gimbal will switch to the Inverted Mode (Allowing the user to flip the gimbal orientation upside down). Pressing the function button three more times while in Inverted Mode to switch back to the original orientation.

Manual Pulling Locking

After the gimbal has been powered on for eight seconds, the tilt angle can be adjusted manually in the Panning Mode and the Lock Mode. Adjust the title angle to the desired position and wait for 0.5 second until the gimbal registers the new angle.

Tilt and Level Calibration By using the optional FY remote control, tilt and level can be adjusted without connection to a computer.

For more information, please refer to FY remote control section in the instruction manual.

Reset

Pressing the function button four consecutive times will reset the gimbal to initial orientation.

Long Press For 1 Second

Long Press For 2 Second

Long Press For 3 Second

On Constantly

Operation LED Status

Function Explanation

Lock Mode

Function Button Quick Reference

Double Tap

Single Tap

LED Flashes Once

LED Flashes Twice

Panning Mode

Panning and Tilting Mode

Triple Tap

LED Flashes Once

Inversion Mode

Quadruple Tap

LED Flashes Once

Reset

Charger

Input: DC 5V Min 800mA Output: DC 4.2V

Type: 16340

M2 * 6mm

Rechargeable Battery

Long screw

M 1.5 Allen Key

T-Clamp

Quick-Release

Buckle

Curved Adhesive

Mounts

3M Adhesive

5V USB Power Adapter （Not Included）

HexagonalSocket

HeadCap Screw

Forward Inverted

Vertical

Camera In RightCamera In Right

Camera In

Right

Camera in Left Camera in Left Camera in Left

Please choose one way:

Rolling

Tilting

Panning

Function

Button

Hexagonal Socket Head Cap Screw

T-Clamp

Accessories For 1/4 Inch Screws

Long screw

Adhesive

Power on: Ensure the camera is mounted securely, then hold down the function button for 2 seconds to turn on the gimbal.

Power off: Hold down the function button for 3 seconds to turn off the gimbal.

Page 2

WARNING

Make sure that the connection to the computer is done by the

Initialization Instructions

FY WGS needs to be initialized whenever the following situations are observed after power on

UP LEFT RIGHTDOWN

Turn Off The Gimbal

Firmware Upgrade

Initialize The Gimbal

FY Remote Control (Optional Item)

Motionless Flat Surface

185.5g (Without Batteries & Camera)

3°/S ~ 150°/S

Usage Time 3 ~ 4 Hours

2°/S ~ 75°/S

320°

100°

Parameters

Upgrade........

Mode #3 Lock Mode

USB Cable

Function Interface

USB Data Cable for RC

Function

Button

Direction

Button

Function Interface

Operation

Explanation

Remark

Tap Button Seven Times

Double Tap

Single Tap

Mode #1 Panning Mode

Mode #2 Panning and Tilting Mode

Triple Tap Triple tap againInversion Mode

,exit inversion mode into original status

Quadruple Tap Reset

Long Press For 1 Second

Long Press For 3 Second

Direction Button

The function button on the Gimbal will be disabled after connect the Remote Control

Please visit the official website of Feiyu Tech: www.feiyu-tech.com to download the USB driver, firmware upgrade software and the latest firmware. Unzip the compressed file locally to your computer. Refer to the connection diagram on how to connect the gimbal with the computer. Please follow the instructions inside the firmware upgrade package carefully, or there will be a risk of rendering the gimbal inoperable.

The tilt and level settings can be calibrated through the use of the configuration software. User can adjust the tilt and diagonal rotation in small intervals to better adapt to his/her filming scene. Before any calibration, please insert the batteries into the gimbal and refer to the connection diagram to connect the gimbal with the computer.

The panning speed can be adjusted through the use of the configuration software. User can adjust to the desired panning speed to better adapt to his/her filming scene. There are three settings available: “SLOW”, “NORMAL” and “FAST”. Default setting is “FAST”.

Firmware Upgrade Instruction

Tilt and Level Calibration

Panning Speed Adjustment

Be sure to insert the batteries before upgrading

USB Connector

Attention : Please make sure that the connection to the computer is done by the USB connector.

FY WGS 3-Axis Wearable Gimbal is a feature-rich camera stabilizer, yet lightweight and portable. It is prohibited for any user to use the gimbal for any illegal purposes. Guilin Feiyu Electronic Technology Co.,Ltd and our associates assume no liability for any accident, injury, death, loss, or other claim related to or resulting from the use of this product. In no event shall Guilin Feiyu Electronic Technology Co.,Ltd and our associates be liable for incidental or consequential damages relating to or resulting from the use of this product or any of its parts. Damage resulting from use, accident, or normal wear and tear is not covered by our warranty. Guilin Feiyu Electronic Technology Co.,Ltd reserves the right to amend this manual and the terms and conditions of this product at any time.

DISCLAIMER

ATT E N TI O N

1. Ensure gimbal is fully assembled and camera is installed properly.

2. Place the gimbal on a flat surface and keep it stationary.

3. Power on the Gimbal.

4. Wait for the gimbal to finish its initialization before resuming the use of the gimbal.

1. The tilt angle is not leveled with the horizontal surface.

2. The roll angle is not parallel to the horizontal surface.

3. When the gimbal is stationary, the camera does not stay stationary.

When initialization is completed, the LED light will quickly flash.

Note:

Vertical Tilting Angle

Rolls Angle

Horizontal Panning Angle

Tilting Increments

Panning Increments

Weight

73.4mm

94.4mm

93.0mm

Steps to connect wireless remote control:

Tap the function button for seven times，match code complete. You can control the gimbal with wireless remote control in normal after finish match code.

▲ RC needs to be match code whenever the following situations：（1）Connecting properly but still control in fail. （2）Change the receiver or wireless remote control.

Match Code

Install the receiver for wireless remote control: Insert the receiver for wireless remote control into the function port of gimbal .

Open the wireless remote control.

Open the gimbal: Long press the function button on gimbal for two seconds to turn on the gimbal.

Use the wireless remote control to control the gimbal.

15 meters in an open environment.

Connect the Micro interface of wireless remote control with 5V charger by USB cable.

Charging

Remote Control Distance

Wireless

remote control

Receiver

for wireless

remote control

Joystick

Wireless Remote Control

Power

OFF

Function Button

Operation

Long press for

0.5 second Long press for

3 second after single tap

Power on / off

Please install the receiver properly before power on

Tip：The Remote Control will be automatically powered off to save battery if there is no operation within three minutes.

▲ Please assemble the gimbal in accordance to the diagram provided.

▲ Please upgrade the firmware and configuration settings with the provided USB data cable and USB cannector.

▲ Please charge the battery with the provided battery charger.

▲ Please install the camera securely before powering on the gimbal.

Remote Control Operation Instructions

Note:

Wired remote control

Calibration Using Remote Control

Single tap ,exit calibration and enter standby. Wake the gimbal by pressing the function button once again

Tap Button Six Times

Match Code Mode

Match code when connecting properly but still control in fail or change the receiver/wireless remote control.

Wireless RC

Tip：Please complete the match code within 5 seconds after powering the gimbal on.

With the remote control, you can switch the gimbal mode or adjust the angle from a distance.