Gl57nk60dss
Gas Requirements
Leak T÷sting .................... 9-11
Using the GHH
Ughting the GHH .................... 13
Care & MaintenanGe ............... 16
Eel@re You Call
Trouble Ehoot_ng ............. 17-18
Vidt the RdgidaEe Web Site at:
Wsrrant_ ............................. 19
READ AND SAVE THESE INSTRUCTIONS - MADE IN THE U°SoAo
Congratulations on your purchase of a new gas grill! At Electrolux Home Products, we
are very proud of our product and are completely committed to providing you with the
best service possible. Your satisfaction is our number one priority.
We know you'll enjoy your new gas grill and Thank You for choosing our product. We
hope you consider us for future purchases.
PLEASE CAREFULLY READ AND SAVE THESE INSTRUCTIONS
This Use & Care Manual provides specific operating instruction for your model. Use your
gas grill only as instructed in this manual. These instructions are not meant to cover every
possible condition and situation that may occur. Common sense and caution must be
practiced when installing, operating and maintaining any appliance.
Questions? 1-800-320-0859
Please record Grill information for future reference and service work:
Model #:
Serial #:
Date of Purchase:
Gas Type:
Please retain this manual for future reference
6) 2004 Electrolux ttome Products, lnc All rights reserved
IMPORTANT SAFETY INFORMATION
- Read this manual carefully before using your grill to reduce the risk of fire, bum hazaM or
other injury.
- Extreme cam should be used because of the high telnperatures produced by this appliance. CHILDREN SHOULD NOT BE LEFT
UNATTENDED IN AN AREA WHERE THE ()RILL IS BEING OPERATED.
- This appliance must be kept clear from combustible materials, gasoline or other flammable vapors and liquids. Do not allow
flalmnable materials to come in contact with grate, burner or hot surfaces.
- Do not repair or replace any part of this appliance unless it is specifically recommended in this manual. A qualified service techni-
cian should conduct all other service.
- Follow the installation and servicing instructions provided with this product. Have your grill installed by a qualified service techni-
cian. Locate the main gas supply valve so that you know how to shut the gas off to your grill. If you smell gas, make sum all gas
connections are tight before operation. If you continue to smell gas call a qualified technician.
- When lighting a burner, always pay close attention to what you am doing. Be certain you are pushing the ignitor that lights the
burner you intend on using.
2
9
2.
3
10
5
G
.
Roll top grill hood
Grilling/Cooking surface
13
10
14
15
11
.
Warming shelf (not shown)
9.
Infrared back burner
3.
Side Shelf
10.
Electronic ignitors: main, rear infrared
& side burner
Control knob: back infrared burner
.
Control knobs: main burners
5.
7.
Warming drawer
tlandle
11. Cart w/doors
12. Drip Pans
13. Side Burners
14. Control knobs:side burner
15. Control knob: bottom infrared burner
Note: Prior to assembly remove protective film from stainless steel parts
Battery:r i_ ii I
Ignitor Attachment
1. Remove the ignitor cap, spring assembly, bat-
tery and lock nut from ignitor. (See Fig. 1)
.
Insert the threaded section of the ignitor into
the U-shaped cut out of the ignitor mounting
bracket. (See Fig. 2)
.
Insert the threaded section of the ignitor
through the hole in the shelf and secure to
shelf using the lock nut. (Use the ignitor
assembly diagrams to determine which
ignitor goes with which shelf.) Tighten
Securely. (See Fig. 3)
Cap
Spring
Assembly
Nut Cylinder Bracket
i
Fig. 1
I
Fig. 2
Fig. 3
.
Re-insert the battery, positive side first, and
spring assembly and attach the ignitor cap.
(See Fig. 4)
.
Repeat above steps for second ignitor
on the other shelf.
GL57 Ignitor Assembly
Right Shelf (Double Wire) Left Shelf (Four Wire)
Fig. 4
! L, sembl
Side Shelves Attachment
1. Loosen the bolts on the side of the grill and
attach the shelf by allowing the bolt heads to
fall through the large opening in the bottom of
the keyhole slots. Then slide the shelves
downward until the bolts are resting against
the top of the key hole slots. Tighten all of
the shelf bolts. (See Fig. 5)
.
Attach the wires coming out from the sides of
the grill to the ignitor terminals. (See Fig. 6)
.
Repeat tbr second side shelf
Note:
It does not matter which wire goes to which
terminal on the four and two wire ignitor
Fig. 5
Fig. 6
Installing Side Burner Plates:
1. There are 2 Black Circle Plates that need
to be installed for the Side Burner to
operate correctly.
2. Lift the Grate off of the Side Burner.
.
Place the Black Circle on top of the one
Burner. (Repeat Step for second burner.)
(See Fig. 7)
.
Replace Grate on top of the dual burners.
(See Fig. 8)
Fig. 7
Fig. 8
Loading...