|
|
Start Here |
|
|
|
Series |
|
|
|
|
|
|
|
||
|
|
Easy Setup Instructions |
|
|
|
Photo Printer |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 Unpack the Printer |
2 Prepare the Printer |
3 Install the Print Head |
4 Install the Ink Tanks |
|
|
Connect the Printer |
|
|
|
5 and Load Paper |
|||||
1 Carefully remove all items from the box.
PIXMA iP5200
Photo Printer
Documentation and
Software Kit
PIXMA iP5200
Print Head
Power Cord
CLI-8BK Black |
CLI-8Y Yellow |
CLI-8M Magenta |
PGI-5BK Black |
CLI-8C Cyan |
|
Ink Tanks
2 Remove the tape from the printer.
1Before turning on the printer, open the top cover and remove the protective material and tape from the printer as shown. The tape position is subject to change.
CAUTION: Be sure to remove the protective material before you turn on the printer.
2Close the top cover. Plug the power cord into the back of the printer and connect the other end to a power outlet. Press the POWER button. The printer will initialize. Wait until the
POWER lamp displays a steady green light.
POWER Button
POWER Lamp
3Open the front cover. Raise the top cover. Lower the inner cover.
NOTE: Push the open button above the front cover. The front cover automatically opens.
Open Button
Top Cover
Inner Cover
Front Cover
4The print head holder automatically moves to the center. Write down the serial number located inside the printer. You will need this to register your products.
1 Remove the print head from its package. |
1 Peel back the orange tab completely and |
|
remove the plastic wrapper from the Cyan Ink |
|
Tank (CLI-8C). |
Tear at notch to open
CAUTION: There might be some transparent or light blue ink on the inside of the bag the print head comes in - this has no effect on print quality. Be careful not to get ink on yourself when handling these items.
2Remove the orange protective cap from the print head.
CAUTION: There might be some transparent or light blue ink on the inside of the protective cap - this has no effect on print quality. Be careful
not to get ink on yourself when handling these items.
NOTE:
·Do not touch the print head nozzles and the electrical contacts.
·Do not attempt to reattach the protective cap once it has been removed.
Print Head |
Electrical |
|
Contacts |
||
Nozzles |
||
|
3 Firmly raise the print head lock lever.
4Slide the print head into the holder. The print head will rest at a slight angle.
2Twist off and discard the orange protective cap located on the bottom of the ink tank.
IMPORTANT: Do not touch the electrical contacts.
NOTE:
·To avoid spilling ink, never press on the sides of an ink tank.
·Do not touch the open ink port once the protective cap is removed, as this may prevent the ink from
being ejected properly.
Protective Cap
Ink Port
Electrical Contacts
3Insert the ink tank into the rightmost slot.
Press the 
mark on the ink tank until it clicks into place and then its lamp lights red.
click |
Ink Tank Lamp
4Insert the remaining four ink tanks into their assigned slots. Ensure that ink tank lamps light red.
Refer to the color guide on the print head lock lever.
5Close (a) the inner cover and then (b) the top cover. Lift open the paper support and extend the paper output tray.
IMPORTANT: Be sure to close the inner cover completely, or the paper will not feed properly.
Paper Support
(a) Inner Cover
(b) Top Cover
IMPORTANT: Be sure the printer is off before continuing, or the computer will attempt to install the printer driver before the printer is ready.
1TURN THE PRINTER OFF.
2Connect one end of the USB cable to the computer, the other to the appropriate USB port on the printer.
NOTE: The iP5200 Photo Printer is equipped with USB 2.0 Hi-Speed port. If your PC does not support USB 2.0 Hi-Speed, or if any noncertified USB 2.0 cable or driver is used for the connection, the printer will operate at a lower speed provided under USB 1.1.
USB Port
USB Cable |
USB Port |
|
USB Cable
3Pinch the paper guide and slide it to the left. Load a few sheets of blank paper into the auto sheet feeder, align the paper with the cover guide, then slide the paper guide toward the left edge of the paper.
Auto Sheet
Feeder
Print Side
Paper |
Cover Guide |
Guide |
IMPORTANT: Print Head Alignment (Step 6) requires that letter size paper is loaded in the Auto Sheet Feeder (top paper feeder).
5 Lower the print head lock lever carefully and press it down.
Serial Number Location
IMPORTANT: If the top cover is left open for more than 10 minutes, the print head holder moves to the right. Close and reopen the top cover to return the holder to the center.
Paper Output Tray
NOTE:
·The printer will perform a print head cleaning. Wait until the POWER lamp displays a steady green light before proceeding.
·If the ALARM lamp still flashes orange even after the printer has stopped making operating noises, an ink tank may not be installed properly. Open the top cover and make sure that the ink tanks are installed in the correct order directed on the label.
Continue with Step 6 on side two.
Loading...