BMW K1200 LT, R 1150 GS User Manual

Supplementary Rider’s Manual
DWA 5 Anti-Theft Alarm System
1
Note:
d Warning:
This symbol indicates pre­cautions and measures which are essential in order to pro­tect the rider and other per­sons from possibly severe or fatal injury.
1
BMW recommends Castrol
Welcome to BMW
Congratulations on your pur­chase of this BMW anti-theft alarm. It acts as a deterrent for poten­tial thieves, while at the same time being easy and straightfor­ward to use.
Welcome to BMW
i
1
Introduction
Your authorised BMW motorcy­cle dealer will be glad to assist you in all matters relating to your motorcycle. We hope you will enjoy familiar­ising yourself with these instructions for use, and we would like to take this opportu­nity of sending you our very best wishes.
Yours sincerely,
BMW Motorrad
Contents
i
2
i Introduction
Welcome to BMW .................1
General ................................. 3
1 Overview and operation
Controls ................................ 4
Introduction
Functions of the remote
control unit............................ 5
Code card ............................. 6
2 Immobiliser
Activation .............................. 7
Deactivation .......................... 9
3 Alarm function
Activation ............................ 10
Activation phases................ 12
How the alarm is
triggered .............................13
Deactivation ........................ 14
Reasons for an alarm ..........16
5 Lights
Lights.................................. 23
6 Programming
Customising the anti-theft
alarm system ...................... 24
Default settings ................... 25
Accessing the
programming mode ............ 26
Programming ...................... 27
Exiting
programming mode ............ 28
7 Remote control units
Registering remote
control units ........................ 29
Exiting registration mode .... 32
Synchronising the
remote control unit.............. 33
8 Care and maintenance
Changing the battery .......... 34
4 Central locking system
Manual operation ................19
Remote control unit............. 20
Emergency unlocking.......... 21
Safety shutdown ................. 22
9 Technical data
Technical data .................... 36
i Index
Index................................... 37
Any attempt to move the motor­cycle, change its position, start it without your permission, or disconnect the battery will trig­ger the alarm. The sensitivity of the system is set in such a way that slight vibrations of the motorcycle will not trigger a false alarm. Once you have activated the alarm, any attempted theft is indicated acoustically by the siren and visually by all four turn indicators flashing at the same time, and the integrated immo­biliser suppresses engine start.
General
Your anti-theft alarm is com­bined with a central locking sys­tem that enables you to open and close the cases, the top­case, and the radio compart­ment by remote control. It also enables you to switch on the map-reading light and the ground lights automatically. You can customise the anti­theft alarm in certain ways to suit your needs and prefer­ences.
L Note:
In order to protect the motorcy­cle’s battery and ensure that the engine can be started, the alarm system deactivates itself automatically a certain number of days after being activated, al­though it always remains active for at least 7 days.
i
3
Introduction
Controls
1
1
4
Overview and operation
1 Left button (ribbed) 2 Right button 3 LED 4 Radio remote control unit 5 Status LED
(on the vehicle)
2
3
4
5
L Note:
Do not be tempted to use the remote control unit to lock the keys inside a stowage compart­ment. If you were to mislay the remote control unit the keys would be inaccessible and you would be able neither to open the cases by means of the emergency unlocking routine nor to deactivate the electronic immobiliser.
Functions of the remote control unit
Operation Button 1 Confirmation
Press once Lock central locking
Press again Activate alarm func-
tion and immobiliser
Press for third time Deactivate motion
sensor (for transport, for example)
Operation Button 2 Confirmation
Press once Deactivate alarm
function and immo­biliser, unlock cen­tral locking
Press again
Press for third time
Turn indicators flash 2x Alarm tone sounds 2x (if pro­grammed)
Indicators flash 3x Alarm tone sounds 3x
Indicators flash 1x Alarm tone sounds 1x (if programmed)
L Note:
The signals from your remote control unit could be disrupted by interference from other radio sys­tems or devices transmitting on the same frequency. If you encounter this problem, try pointing the remote control unit at the motorcycle from a different di­rection.
1
5
Overview and operation
Code card
1
6
Overview and operation
The anti-theft alarm is supplied complete with a sealed enve­lope containing a code card 1. The number stated on the code card (remove the adhesive label) is the code for deactivat­ing the anti-theft alarm by means of the ignition ( It is advisable to keep the code card with the vehicle registra­tion papers, and carry both with you when you ride the motorcy­cle.
b 17).
1
2
The code number is stamped in encrypted form on the anti-theft alarm and it is also printed on an adhesive label 2 supplied with the anti-theft alarm. You should affix the label at a con­cealed location on the motorcy­cle. If you forget the code and are unable to find the code card, an authorised BMW motorcycle dealer will be able to forward the encrypted number to BMW on your behalf and obtain the correct code.
1 2
Activation
5
2
7
Once the immobiliser has been activated the engine will refuse to start even if an authorised key is used for the start attempt. You can tell whether the immobiliser is activated by switching on the ignition and observing LED 5; if the immobi­liser is active it will light up when the pre-ride check completes.
L Note:
The remote control unit acti­vates both the immobiliser and the alarm function. It is also possible to have the immobiliser activated automati­cally when the ignition is switched off (default) without activation of the alarm function
b 26).
(
Activation
The immobiliser is activated
• by pressing button 1 on the
remote control unit twice (alarm function is also acti­vated)
or
• by switching off the ignition, if programmed (
When you switch off the igni­tion, 50 seconds elapse before the activation phase.
b 26)
Immobiliser
Activation
2
8
Immobiliser
Activation of the immobiliser after ignition off but without activation of the alarm function is confirmed
• by the turn indicators flashing once
and
• by the alarm tone sounding once, if programmed (
Activation of the immobiliser with activation of the alarm function by means of the remote control unit is confirmed
• by the indicators flashing twice
and
• by the alarm tone sounding twice, if programmed (
b 26)
b 26)
If confirmation takes the form of the alarm tone sounding four times, this is to indicate that the anti-theft alarm's internal rechargeable battery is dis­charged. The rechargeable bat­tery of the anti-theft alarm is charged through the on-board electrical system, which means that this problem might be due to a discharged starter battery. When the anti-theft alarm's internal battery is discharged the alarm will not be triggered by an attempt to disconnect the starter battery. Contact your authorised BMW motorcycle dealer if the alarm tone sounds four times on acti­vation even after a lengthy jour­ney.
1 2
Deactivation
2
9
Immobiliser
Deactivating the immobi­liser with the remote con­trol unit
The immobiliser is deactivated
• by pressing button 2 on the
remote control unit once (if the immobiliser was activated automatically beforehand when you switched off the ignition, it is reactivated 30 seconds later).
Deactivation is confirmed
• by the turn indicators flashing once
and
• by the alarm tone sounding once, if programmed (
b 26)
If confirmation takes the form of the alarm tone sounding four times, this is to indicate that the voltage in the on-board elec­tricity supply has dropped below a predefined threshold. In this case, recharge the motorcycle's starter battery
b Rider's Manual).
(
Deactivating the immobi­liser without the remote control unit
The procedure is the same as that for deactivating the alarm function without the remote control unit (
b 15).
Activation
3
10
Alarm function
Activation with motion sensor
The alarm function is activated
• by pressing button 1 on the
remote control unit twice
or
• by switching off the ignition, if programmed (
When you switch off the igni­tion, 50 seconds elapse before activation. The central locking system is not activated.
b 25)
1 2
Activation is confirmed
•by the indicators flashing twice
and
• by the alarm tone sounding twice, if programmed (
b 26)
Loading...
+ 30 hidden pages