Version 1.0
Published February 2018
Copyright©2018 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.
Products and corporate names appearing in this documentation may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to
infringe.
Disclaimer:
Specifications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose.
In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)this device may not cause harmful interference, and
(2)this device must accept any interference received, including interference that may cause undesired operation.
CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/ perchlorate”
ASRock Website: http://www.asrock.com
AUSTRALIA ONLY
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage caused by our goods. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. If you require assistance please call ASRock Tel : +886-2-28965588 ext.123 (Standard International call charges apply)
The terms HDMI™ and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
H310M-HDV/M.2
Motherboard Layout
|
|
|
1 |
2 |
3 |
|
4 |
/Mouse Keyboard PS2 |
USB: USBT: US2 B. 2 1 0 |
|
CPU_FAN1 |
|
|
CHA_FAN1/WP |
|
|
|
|
ATX12V1 |
|
|
|
|
DVI1 |
|
VGA1 |
|
|
|
|
ATXPWR1 |
HDMI1 |
|
|
|
|
pinmodule) |
pinmodule) |
|
|
|
|
|
|
A1(64bit,288- |
B1(64bit,288- |
109USB |
USB 3.1 Gen1 |
|
|
DDR4 |
DDR4 |
|||
T: USB3 |
|
|
|
|
|
|
|
B: USB4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 |
|
|
|
|
|
|
|
1 |
USB 2.0 |
Top: |
Intel |
CMOS |
|
|
USB11 12 |
|
B: USB6 |
|
|
|||||
RJ-45 |
Battery |
|
|
||||
T: USB5 |
|
|
|
|
|
|
|
INMI Bottom: C |
FRONT Center: |
|
H310 |
|
|
|
|
LINE Top: |
LAN |
|
|
|
|
PCIE1
BIOS
ROM
CODEC |
|
PCIE2 |
AUDIO |
|
|
PCIE3 |
CT4 |
CT3 |
|
H310M-HDV/M.2 |
SATA32 |
SATA33 |
||
|
|
|
|
||
|
|
|
|
SATA3 0 |
SATA3 1 |
|
|
1 |
|
|
|
|
|
M2 |
1 |
|
|
CT2 |
CT1 |
CLRMOS1 |
|
|
|
|
|
RoHS |
PANEL1 |
CHA_FAN2/WP |
|
|
|
|
|
||
|
|
|
|
|
PLED PWRBTN |
|
HD_AUDIO1 |
TPMS1 |
LPT1 |
COM1 |
USB_7_8 |
SPK_CI1 |
|
|
|
|
||||
|
1 |
|
|
|
|
|
|
1 |
1 |
|
1 |
1 |
|
1 |
|
|
|
1 HDLED |
RESET |
20 |
19 |
18 |
17 |
16 |
15 |
14 |
5
6
7
8
9
10
11
12
13
English
1
No. Description
1ATX 12V Power Connector (ATX12V1)
2CPU Fan Connector (CPU_FAN1)
32 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)
4Chassis/Water Pump Fan Connector (CHA_FAN1/WP)
5ATX Power Connector (ATXPWR1)
6USB 2.0 Header (USB_9_10)
7USB 3.1 Gen1 Header (USB_11_12)
8SATA3 Connector (SATA3_2)
9SATA3 Connector (SATA3_3)
10Clear CMOS Jumper (CLRMOS1)
11SATA3 Connector (SATA3_0)
12SATA3 Connector (SATA3_1)
13Chassis/Water Pump Fan Connector (CHA_FAN2/WP)
14System Panel Header (PANEL1)
15Chassis Intrusion and Speaker Header (SPK_CI1)
16USB 2.0 Header (USB_7_8)
17COM Port Header (COM1)
18Print Port Header (LPT1)
19TPM Header (TPMS1)
20Front Panel Audio Header (HD_AUDIO1)
English
2
H310M-HDV/M.2
I/O Panel
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4 |
|
1 |
2 |
|
|
|
|
3 |
|
|
|
|
|
5 |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
11 |
10 |
|
|
9 |
|
8 |
|
|
|
7 |
|
|
6 |
|||
No. |
Description |
|
No. |
Description |
|
|
|
|
||||||||
1 |
|
USB 2.0 Ports (USB12) |
|
7 |
USB 2.0 Ports (USB5_6) |
|
||||||||||
2 |
|
D-Sub Port |
|
8 |
USB 3.1 Gen1 Ports (USB_3_4) |
|||||||||||
3 |
|
LAN RJ-45 Port* |
|
9 |
HDMI Port |
|
|
|
|
|||||||
4 |
|
Line In (Light Blue)** |
|
10 |
DVI-D Port |
|
|
|
|
|||||||
5 |
|
Front Speaker (Lime)** |
|
11 |
PS/2 Keyboard/Mouse Port |
|
6Microphone (Pink)**
*There are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.
ACT/LINK LED
SPEED LED
LAN Port
Activity / Link LED |
Speed LED |
|
|
||
Status |
|
Description |
Status |
|
Description |
Off |
|
No Link |
Off |
|
10Mbps connection |
|
|
||||
Blinking |
|
Data Activity |
Orange |
|
100Mbps connection |
On |
|
Link |
Green |
|
1Gbps connection |
English
3
** To configure 7.1 CH HD Audio, it is required to use an HD front panel audio module and enable the multichannel audio feature through the audio driver.
Please set Speaker Configuration to “7.1 Speaker”in the Realtek HD Audio Manager.
Function of the Audio Ports in 7.1-channel Configuration:
Port
Light Blue (Rear panel)
Lime (Rear panel)
Pink (Rear panel)
Lime (Front panel)
Function
Rear Speaker Out
Front Speaker Out
Central /Subwoofer Speaker Out
Side Speaker Out
English
4
H310M-HDV/M.2
Chapter 1 Introduction
Thank you for purchasing ASRock H310M-HDV/M.2 motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance.
Because the motherboard specifications and the BIOS software might be updated, the content of this documentation will be subject to change without notice. In case any modifications of this documentation occur, the updated version will be available on ASRock’s website without further notice. If you require technical support related to this motherboard, please visit our website for specific information about the model you are using. You may find the latest VGA cards and CPU support list on ASRock’s website as well. ASRock website http://www.asrock.com.
1.1 Package Contents
•ASRock H310M-HDV/M.2 Motherboard (Micro ATX Form Factor)
•ASRock H310M-HDV/M.2 Quick Installation Guide
•ASRock H310M-HDV/M.2 Support CD
•1 x I/O Panel Shield
•2 x Serial ATA (SATA) Data Cables (Optional)
•1 x Screw for M.2 Socket (Optional)
English
5
1.2 Specifications
Platform |
• |
Micro ATX Form Factor |
|
• |
Solid Capacitor design |
CPU |
• |
Supports 8th Generation Intel® CoreTM Processors (Socket |
|
|
1151) |
|
• 5 Power Phase design |
|
|
• Supports Intel® Turbo Boost 2.0 Technology |
|
Chipset |
• |
Intel® H310 |
Memory |
• |
Dual Channel DDR4 Memory Technology |
|
• 2 x DDR4 DIMM Slots |
|
|
• Supports DDR4 2666/2400/2133 non-ECC, un-buffered |
|
|
|
memory |
|
• Max. capacity of system memory: 32GB |
|
|
• Supports Intel® Extreme Memory Profile (XMP) 2.0 |
|
|
• 15μ Gold Contact in DIMM Slots |
|
Expansion |
• |
1 x PCI Express 3.0 x16 Slot (PCIE1: x16 mode)* |
Slot |
* Supports NVMe SSD as boot disks |
|
|
• 2 x PCI Express 2.0 x1 Slots |
|
Graphics |
• |
Intel® UHD Graphics Built-in Visuals and the VGA outputs |
|
|
can be supported only with processors which are GPU |
|
|
integrated. |
|
• Supports Intel® UHD Graphics Built-in Visuals : Intel® |
|
|
|
Quick Sync Video with AVC, MVC (S3D) and MPEG-2 Full |
|
|
HW Encode1, Intel® InTruTM 3D, Intel® Clear Video HD |
|
|
Technology, Intel® InsiderTM, Intel® UHD Graphics |
|
• |
DirectX 12 |
|
• HWAEncode/Decode: AVC/H.264, HEVC/H.265 8-bit, |
|
|
|
HEVC/H.265 10-bit, VP8, VP9 8-bit, VP9 10-bit (Decode |
|
|
only), MPEG2, MJPEG, VC-1 (Decode only) |
English
6
H310M-HDV/M.2
• Three graphics output options: D-Sub, DVI-D and HDMI * Supports up to 2 displays simultaneously
• Supports HDMI with max. resolution up to 4K x 2K (4096x2160) @ 30Hz
• Supports DVI-D with max. resolution up to 1920x1200 @ 60Hz
• Supports D-Sub with max. resolution up to 1920x1200 @ 60Hz
• Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and HBR (High Bit Rate Audio) with HDMI Port (Compliant
|
|
HDMI monitor is required) |
|
• Supports HDCP with DVI-D and HDMI Ports |
|
|
• Supports 4K Ultra HD (UHD) playback with HDMI Port |
|
Audio |
• |
7.1 CH HD Audio (Realtek ALC887 Audio Codec) |
|
* To configure 7.1 CH HD Audio, it is required to use an HD |
|
|
front panel audio module and enable the multi-channel audio |
|
|
feature through the audio driver. |
|
|
• |
Supports Surge Protection |
|
• |
ELNA Audio Caps |
LAN |
• |
Gigabit LAN 10/100/1000 Mb/s |
|
• Giga PHY Intel® I219V |
|
|
• Supports Wake-On-LAN |
|
|
• |
Supports Lightning/ESD Protection |
|
• Supports Energy Efficient Ethernet 802.3az |
|
|
• |
Supports PXE |
Rear Panel |
• |
1 x PS/2 Mouse/Keyboard Port |
I/O |
• |
1 x D-Sub Port |
• 1 x DVI-D Port
• 1 x HDMI Port
• 4 x USB 2.0 Ports (Supports ESD Protection)
• 2 x USB 3.1 Gen1 Ports (Supports ESD Protection)
• 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED LED)
• HD Audio Jacks: Line in / Front Speaker / Microphone
English
7
English
Storage |
• 4 x SATA3 6.0 Gb/s Connectors, support NCQ, AHCI and |
|
Hot Plug* |
*If M2_1 is occupied by a SATA-type M.2 device, SATA3_3 will be disabled.
•1 x M.2 Socket (M2_1), supports M Key type 2230/2242/2260/2280 M.2 SATA3 6.0 Gb/s module and M.2 PCI Express module up to Gen2 x4 (20 Gb/s)**
**Supports NVMe SSD as boot disks
**Supports ASRock U.2 Kit
Connector |
• 1 x Print Port Header |
•1 x COM Port Header
•1 x TPM Header
•1 x Chassis Intrusion and Speaker Header
•1 x CPU Fan Connector (4-pin)
*The CPU Fan Connector supports the CPU fan of maximum 1A (12W) fan power.
•2 x Chassis/Water Pump Fan Connectors (4-pin) (Smart Fan Speed Control)
*The Chassis/Water Pump Fan supports the water cooler fan of maximum 2A (24W) fan power.
*CHA_FAN1/WP and CHA_FAN2/WP can auto detect if 3-pin or 4-pin fan is in use.
•1 x 24 pin ATX Power Connector
•1 x 8 pin 12V Power Connector
•1 x Front Panel Audio Connector
•2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports ESD Protection)
•1 x USB 3.1 Gen1 Header (Supports 2 USB 3.1 Gen1 ports) (Supports ESD Protection)
*USB_11_12 is shared with USB_9_10.
BIOS |
• |
AMI UEFI Legal BIOS with multilingual GUI support |
Feature |
• |
ACPI 6.0 Compliant wake up events |
|
• |
SMBIOS 2.7 Support |
|
• CPU, GT_CPU, DRAM, PCH 1.05V Voltage Multi-adjust- |
|
|
|
ment |
Hardware |
• |
Temperature Sensing: CPU, Chassis/Water Pump Fans |
Monitor |
• |
Fan Tachometer: CPU, Chassis/Water Pump Fans |
8
H310M-HDV/M.2
|
• Quiet Fan (Auto adjust chassis fan speed by CPU |
|
|
|
temperature): CPU, Chassis/Water Pump Fans |
|
• Fan Multi-Speed Control: CPU, Chassis/Water Pump Fans |
|
|
• |
CASE OPEN detection |
|
• Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, DRAM, |
|
|
|
PCH 1.05V |
OS |
• |
Microsoft® Windows® 10 64-bit |
Certifica- |
• |
FCC, CE |
tions |
• |
ErP/EuP ready (ErP/EuP ready power supply is required) |
* For detailed product information, please visit our website: http://www.asrock.com
Please realize that there is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using third-party overclocking tools. Overclocking may affect your system’s stability, or even cause damage to the components and devices of your system. It should be done at your own risk and expense. We are not responsible for possible damage caused by overclocking.
English
9
Chapter 2 Installation
This is a Micro ATX form factor motherboard. Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard components or change any motherboard settings.
•Make sure to unplug the power cord before installing or removing the motherboard components. Failure to do so may cause physical injuries and damages to motherboard components.
•In order to avoid damage from static electricity to the motherboard’s components, NEVER place your motherboard directly on a carpet. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle the components.
•Hold components by the edges and do not touch the ICs.
•Whenever you uninstall any components, place them on a grounded anti-static pad or in the bag that comes with the components.
•When placing screws to secure the motherboard to the chassis, please do not overtighten the screws! Doing so may damage the motherboard.
English
10
H310M-HDV/M.2
2.1Installing the CPU
1.Before you insert the 1151-Pin CPU into the socket, please check if the PnP cap is on the socket, if the CPU surface is unclean, or if there are any bent pins in the socket. Do not force to insert the CPU into the socket if above situation is found. Otherwise, the CPU will be seriously damaged.
2.Unplug all power cables before installing the CPU.
1
A
B
2
English
11
3 |
4 |
5
English
Please save and replace the cover if the processor is removed. The cover must be placed if you wish to return the motherboard for after service.
12
H310M-HDV/M.2
2.2 Installing the CPU Fan and Heatsink
1 |
2 |
N _FA PU C
English
13
English
2.3 Installing Memory Modules (DIMM)
This motherboard provides two 288-pin DDR4 (Double Data Rate 4) DIMM slots, and supports Dual Channel Memory Technology.
1.For dual channel configuration, you always need to install identical (the same brand, speed, size and chip-type) DDR4 DIMM pairs.
2.It is unable to activate Dual Channel Memory Technology with only one memory module installed.
3.It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4 slot; otherwise, this motherboard and DIMM may be damaged.
The DIMM only fits in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.
1
2
3
14
H310M-HDV/M.2
2.4 Expansion Slots (PCI Express Slots)
There are 3 PCI Express slots on the motherboard.
Before installing an expansion card, please make sure that the power supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation.
PCIe slots:
PCIE1 (PCIe 2.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIE2 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards. PCIE3 (PCIe 2.0 x1 slot) is used for PCI Express x1 lane width cards.
English
15
2.5 Jumpers Setup
The illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is “Open”.
Clear CMOS Jumper |
|
Short: Clear CMOS |
(CLRCMOS1) |
2-pin Jumper |
Open: Default |
(see p.1, No. 10) |
|
|
|
|
CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes system setup information such as system password, date, time, and system setup parameters. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord, then use a jumper cap to short the pins on CLRCMOS1 for 3 seconds. Please remember to remove the jumper cap after clearing the CMOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action.
If you clear the CMOS, the case open may be detected. Please adjust the BIOS option “Clear Status” to clear the record of previous chassis intrusion status.
English
16
H310M-HDV/M.2
2.6 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage to the motherboard.
System Panel Header
(9-pin PANEL1)
(see p.1, No. 14)
PLED+ PLED-
PWRBTN#
GND
1
GND RESET#
GND HDLED-
HDLED+
Connect the power button, reset button and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.
PWRBTN (Power Button):
Connect to the power button on the chassis front panel. You may configure the way to turn off your system using the power button.
RESET (Reset Button):
Connect to the reset button on the chassis front panel. Press the reset button to restart the computer if the computer freezes and fails to perform a normal restart.
PLED (System Power LED):
Connect to the power status indicator on the chassis front panel. The LED is on when the system is operating. The LED keeps blinking when the system is in S1/S3 sleep state. The LED is off when the system is in S4 sleep state or powered off (S5).
HDLED (Hard Drive Activity LED):
Connect to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data.
The front panel design may differ by chassis. A front panel module mainly consists of power button, reset button, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly.
English
17
English
Chassis Intrusion and
Speaker Header
(7-pin SPK_CI1)
(see p.1, No. 15)
SPEAKER
DUMMY DUMMY +5V
1
SIGNAL GND
DUMMY
Please connect the chassis intrusion and the chassis speaker to this header.
Serial ATA3 Connectors |
2 |
3 |
These four SATA3 |
see p.1, No. 11) |
SATA3 |
SATA3 |
data cables for internal |
(SATA3_0: |
|
|
connectors support SATA |
(SATA3_1: |
0 |
1 |
storage devices with up to |
see p.1, No. 12) |
SATA3 |
SATA3 |
6.0 Gb/s data transfer rate. |
|
|
||
(SATA3_2: |
|
|
* If M2_1 is occupied by |
see p.1, No. 8) |
|
|
a SATA-type M.2 device, |
(SATA3_3: |
|
|
SATA3_3 will be disabled. |
see p.1, No. 9) |
|
|
|
USB 2.0 Headers
(9-pin USB_7_8)
(see p.1, No. 16)
USB_PWR
P- P+ GND DUMMY
1
GND
USBP_-PWRP+
There are two USB 2.0 headers on this
motherboard. Each USB 2.0 header can support two ports.
(9-pin USB_9_10) |
DUMMY |
|
(see p.1, No. 6) |
GND |
GND |
P+ |
P+ |
|
|
P- |
P- |
|
USB_PWR |
USB_PWR |
|
|
1 |
USB 3.1 Gen1 Header
(19-pin USB_11_12)
(see p.1, No. 7)
1
Dummy IntA_PB_D+ IntA_PB_DGND IntA_PB_SSTX+ IntA_PB_SSTXGND IntA_PB_SSRX+ IntA_PB_SSRXVbus
IntA_PA_D+
IntA_PA_D-
GND
IntA_PA_SSTX+
IntA_PA_SSTX-
GND
IntA_PA_SSRX+
IntA_PA_SSRX-
busV
There is one header on this motherboard. This USB 3.1 Gen1 header can support two ports.
* USB_11_12 is shared with USB_9_10.
18
H310M-HDV/M.2
Front Panel Audio Header
(9-pin HD_AUDIO1)
(see p.1, No. 20)
GND PRESENCE#
MIC_RET
OUT_RET
1
OUT2_L J_SENSE
OUT2_R MIC2_R
MIC2_L
This header is for connecting audio devices to the front audio panel.
1.High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instructions in our manual and chassis manual to install your system.
2.If you use an AC’97 audio panel, please install it to the front panel audio header by the steps below:
A.Connect Mic_IN (MIC) to MIC2_L.
B.Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C.Connect Ground (GND) to Ground (GND).
D.MIC_RET and OUT_RET are for the HD audio panel only. You don’t need to connect them for the AC’97 audio panel.
E.To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel and adjust “Recording Volume”.
Chassis/Water Pump Fan
Connectors
(4-pin CHA_FAN1/WP)
(see p.1, No. 4)
(4-pin CHA_FAN2/WP)
(see p.1, No. 13)
GND
|
FAN_VOLTAGE |
|
||
|
|
FAN_SPEED |
|
|
|
|
|
FAN_SPEED_CONTROL |
|
1 |
2 |
3 |
4 |
|
FAN_SPEED_CONTROL |
4 |
|||
CHA_FAN_SPEED |
3 |
|||
|
FAN_VOLTAGE |
2 |
||
|
|
|
GND |
1 |
This motherboard provides two 4-Pin water cooling chassis fan connectors. If you plan to connect a 3-Pin chassis water cooler fan, please connect it to Pin 1-3.
CPU Fan Connector
(4-pin CPU_FAN1)
(see p.1, No. 2)
FAN_SPEED_CONTROL CPU_FAN_SPEED FAN_VOLTAGE
GND
1 2 3 4
This motherboard provides a 4-Pin CPU fan (Quiet Fan) connector. If you plan to connect a 3-Pin CPU fan, please connect it to Pin 1-3.
English
19