Installation
&
Operating
Instructions
110 CS 160200
Type C…
825 12 39-12 |
MO-M 0714 |
Introduction
Thank you for choosing the Electrolux Wine Cellar.
Please read the following instructions carefully before installing your new wine cellar. We trust you will be completely satisfied with your purchase.
The wine cellar must be installed and used according to these instructions in order for it to operate correctly and economically.
Transit damage
Inspect the wine cellar for transit damage. You must report any damage the company responsible for the delivery within the legal or stated time for this type of product. If there is no such established report time, the damage must be reported within seven days of delivery.
Accessories
Please check that the following accessories are attached to the Wine Cellar or in the separate cardboard box inside the wine cellar.
Cardboard box:
•Handle
•Storage shelves
•Drip tray
•Support (floor)
•Shelf supports
•Screws
•Washers (wooden door)
•Keys
•CD
•Instruction manual
Necessary additional tools not included:
•Screwdriver (star quad)
•Adjustable spanner or fixed spanner (21 mm)
Data plate
Check the data plate, inside the wine cellar at the top left, to ensure you have received the right model.
The data plate shows details that you will need to quote if you have to contact service personnel.
It is a good idea to make a note of them here:
Model designation. . . . . . . . . . . . .
Product number. . . . . . . . . . . . . .
Serial number. . . . . . . . . . . . . .
Voltage . . . . . . . . . . . . . . . . .
Installation
Please follow these instructions:
•For best performance, air needs to circulate freely over the cooling unit behind the wine cellar.
•The free-standing design of the cellar means that it should stand at least 25 mm from the rear and side walls.
•Allow a clearance of at least 100 mm above the wine cellar.
Wall
25 mm
Rear
25 mm
30 mm |
Wall |
•Note that it must be possible to open the wine cellar door at least 90° to allow the sliding shelves to be pulled out.
--
1.Remove the transport pallet on which your wine cellar rests.
2.Adjust the feet to allow a 30 mm clearance under the wine cellar and verify that it stands in a vertical position in both directions. If necessary, use a spirit level.
3.For optimum performance, please place your wine cellar far away from any source of heat, e.g. radiator, cooker or intense sunlight.
. Check that the charcoal filter is in place at the top left corner inside the wine cellar.
5.Fit the door handle to the door, see “Appendix A”.
6.Attach the drip tray on the back. The screws are already attached at the back.
Electrical connection
The electrical installation must be carried out correctly, taking into account all relevant regulations and codes of practice. The wine cellar operates on a single-phased alternating current.
Please check that the voltage shown on the data plate corresponds to your power supply.
! |
WARNING |
The wine cellar must be earthed.
The wine cellar is fitted with a plug intended for an earthed socket. Electrolux and its subsidiaries will not be held responsible for any incident due to nonexistent or defective earth wires.
Electrical leads must be routed and secured so that they cannot come into contact with hot or sharp parts of the wine cellar.
Temperature setting
Plug in the wine cellar and turn it on with the ON/ OFF switch.
The wine cellar is equipped with an electronic control. This allows you to programme the temperature inside the wine cellar. The wine will be stored between 10°C and 15°C according to expert advice. and 15°C according to expert advice. The temperature, pre-set at 12°C in the factory, is shown on the display. The temperature can be changed on demand between 8°C and 18°C depending on the wine stored.
1.Press and hold the UP (▲) or DOWN (▼) arrow button for a few seconds until the display starts blinking.
2.Release the button. Press the UP/DOWN arrow buttons to set the temperature. The new value is saved automatically after 6 seconds.
- -
Loading...