English
Français
Español
Owner’s Manual
Mode d’emploi
Manual de instrucciones
EN
FR
ES
FCC INFORMATION (U.S.A.) |
||
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! |
not guarantee that interference will not occur in all installations. If |
|
This product, when installed as indicated in the instructions con- |
this product is found to be the source of interference, which can be |
|
tained in this manual, meets FCC requirements. Modifications not |
determined by turning the unit “OFF” and “ON”, please try to elimi- |
|
expressly approved by Yamaha may void your authority, granted by |
nate the problem by using one of the following measures: |
|
the FCC, to use the product. |
Relocate either this product or the device that is being affected by |
|
2. IMPORTANT: When connecting this product to accessories and/ |
the interference. |
|
or another product use only high quality shielded cables. Cable/s |
Utilize power outlets that are on different branch (circuit breaker or |
|
supplied with this product MUST be used. Follow all installation |
fuse) circuits or install AC line filter/s. |
|
instructions. Failure to follow instructions could void your FCC |
In the case of radio or TV interference, relocate/reorient the |
|
authorization to use this product in the USA. |
||
antenna. If the antenna lead-in is 300 ohm ribbon lead, change the |
||
3. NOTE: This product has been tested and found to comply with the |
lead-in to co-axial type cable. |
|
requirements listed in FCC Regulations, Part 15 for Class “B” digital |
If these corrective measures do not produce satisfactory results, |
|
devices. Compliance with these requirements provides a reason- |
||
please contact the local retailer authorized to distribute this type of |
||
able level of assurance that your use of this product in a residential |
||
product. If you can not locate the appropriate retailer, please con- |
||
environment will not result in harmful interference with other elec- |
||
tact Yamaha Corporation of America, Electronic Service Division, |
||
tronic devices. This equipment generates/uses radio frequencies |
||
6600 Orangethorpe Ave, Buena Park, CA90620 |
||
and, if not installed and used according to the instructions found in |
||
The above statements apply ONLY to those products distributed by |
||
the users manual, may cause interference harmful to the operation |
||
Yamaha Corporation of America or its subsidiaries. |
||
of other electronic devices. Compliance with FCC regulations does |
||
|
||
|
|
|
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. |
(class B) |
COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620 Telephone : 714-522-9011
Type of Equipment : PORTABLE PA SYSTEM
Model Name : STAGEPAS 600BT, STAGEPAS 400BT
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1)this device may not cause harmful interference, and
2)this device must accept any interference received including interference that may cause undesired operation.
See user manual instructions if interference to radio reception is suspected.
* This applies only to products distributed by |
(FCC DoC) |
YAMAHA CORPORATION OF AMERICA. |
|
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
(fcc_sengen)
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
(B ) ,.
(class b korea)
2 STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual
PLEASE READ CAREFULLY BEFORE PROCEEDING
Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
Power supply/power cord
•Do not place the power cord near heat sources such as heaters or radiators, and do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it.
•Only use the voltage specified as correct for the mixer. The required voltage is printed on the name plate of the mixer.
•Use only the supplied power cord.
If you intend to use the device in an area other than in the one you purchased, the included power cord may not be compatible. Please check with your Yamaha dealer.
•Check the electric plug periodically and remove any dirt or dust which may have accumulated on it.
•When setting up the device, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. Even when the power switch is turned off, as long as the power cord is not unplugged from the wall AC outlet, the device will not be disconnected from the power source.
•Remove the electric plug from the outlet when the device is not to be used for extended periods of time, or during electrical storms.
•Be sure to connect to an appropriate outlet with a protective grounding connection.
Do not open
•This device contains no user-serviceable parts. Do not open the device or attempt to disassemble the internal parts or modify them in any way. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified Yamaha service personnel.
Water warning
•Do not expose the device to rain, use it near water or in damp or wet conditions, or place on it any containers (such as vases, bottles or glasses) containing liquids which might spill into any openings. If any liquid such as water seeps into the device, turn off the power immediately and unplug the power cord from the AC outlet. Then have the device inspected by qualified Yamaha service personnel.
•Never insert or remove an electric plug with wet hands.
Hearing loss
•Avoid setting all equalizer controls and level controls to their maximum. Depending on the condition of the connected devices, doing so may result in feedback that can cause hearing loss and damage the speakers.
•Before connecting the device to other devices, turn off the power for all devices. Also, before turning the power of all devices on or off, make sure that all volume levels are set to the minimum. Failing to do so may result in hearing loss, electric shock, or device damage.
•When turning on the AC power in your audio system, always turn on the device LAST, to avoid hearing loss and speaker damage. When turning the power off, the device should be turned off FIRST for the same reason.
Fire warning
•Do not place any burning items or open flames near the device, since they may cause a fire.
Wireless unit
•Do not use this device near medical devices or inside medical facilities. Radio waves from this device may affect electro-medical devices.
•Do not use this device within 15 cm (6 in) of persons with a heart pacemaker implant or a defibrillator implant. Radio waves from this device may affect electro-medical devices, such as a heart pacemaker implant or defibrillator implant.
If you notice any abnormality
•If any of the following problems occur, immediately turn off the power switch and disconnect the electric plug from the outlet.
-The power cord or plug becomes frayed or damaged.
-Unusual smells or smoke are emitted.
-Some object has been dropped into the device.
-There is a sudden loss of sound during use of the device.
-Cracks or other visible damage appear on the device. Then have the device inspected or repaired by qualified Yamaha service personnel.
•If this device should be dropped or damaged, immediately turn off the power switch, disconnect the electric plug from the outlet, and have the device inspected by qualified Yamaha service personnel.
English
STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual |
3 |
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following:
Power supply/power cord
•When removing the electric plug from the device or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it.
Location
•Do not place the device in an unstable position where it might accidentally fall over and cause injuries.
•Do not block the vents. This mixer has ventilation holes at the top and sides to prevent the internal temperature from becoming too high. In particular, do not place the mixer on its side or upside down. Inadequate ventilation can result in overheating, possibly causing damage to the mixer, or even fire.
•If you install the mixer apart from the speakers:
-Do not cover it with any cloth.
-Make sure the top surface faces up; do not install on its sides or upside down.
-Do not use the device in a confined, poorly-ventilated location.
Inadequate ventilation can result in overheating, possibly causing damage to the device(s), or even fire. Make sure that there is adequate space around the device: at least 30 cm above, 30 cm at the sides and 30 cm behind.
•If you lay the speaker flat on its side or like a stage monitor, make sure to remove the mixer first.
•Do not use the speaker’s handles for suspended installation. Doing so can result in damage or injury.
•Do not hold the bottom of the speaker when transporting or moving it. In doing so, you may pinch your hands under the speaker, and result in injury.
•Do not place the device in a location where it may come into contact with corrosive gases or salt air. Doing so may result in malfunction.
•Before moving the device, remove all connected cables.
Connections
•For the SPEAKERS jacks of the mixer, use only the included MODEL 600S or MODEL 400S speakers and speaker cables. Use of other types of speakers and cables may result in damage, or even fire.
Maintenance
•Remove the power plug from the AC outlet when cleaning the device.
Handling caution
•Do not insert your fingers or hands in any gaps or openings on the vents or panel of the mixer, and the ports of the speaker.
•Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any gaps or openings on the vents or panel of the mixer, and the ports of the speaker. If this happens, immediately turn off the power of the mixer, unplug the power cord from the AC outlet, and have the device inspected by qualified Yamaha service personnel.
•Do not rest your weight on the device or place heavy objects on it. Avoid applying excessive force to the buttons, switches or connectors to prevent injuries.
•Do not operate the device if the sound is distorting. Prolonged use in this condition could cause overheating and result in fire.
•Avoid pulling the cables such as microphones to prevent injuries or damage to the speakers and mixer by causing them to fall.
Yamaha cannot be held responsible for damage caused by improper use or modifications to the device.
4 STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual
To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below.
■ Handling and maintenance
•Do not expose the device to excessive dust or vibration, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day), in order to prevent the possibility of panel disfiguration, unstable operation, or damage to the internal components.
•Do not place vinyl, plastic or rubber objects on the device, since this might discolor the panel.
•When cleaning the device, use a dry and soft cloth. Do not use paint thinners, solvents, cleaning fluids, or chemicalimpregnated wiping cloths.
•Condensation can occur in the device due to rapid, drastic changes in ambient temperature—when the device is moved from one location to another, or air conditioning is turned on or off, for example. Using the device while condensation is present can cause damage. If there is reason to believe that condensation might have occurred, leave the device for several hours without turning on the power until the condensation has completely dried out.
•Protection Circuit: This speaker system has an internal protection circuit that shuts off the speaker unit when an excessive input signal is applied. If the speaker unit emits no sound, reduce the volume level of the amplifier immediately. The sound will return automatically in several seconds.
•When placing the speaker face down, always place it on a flat surface.
•Do not touch the speaker driver unit.
•The rubber feet included in this package can be attached to the speaker to prevent slippage when it is to be used on a slippery surface.
•Air blowing out of the bass reflex ports is normal, and often occurs when the speaker is handling program material with heavy bass content.
•Always turn the power off when the device is not in use.
■ Connectors
•XLR-type connectors are wired as follows (IEC60268 standard):
pin 1: ground pin 2: hot (+) pin 3: cold (–).
■ About this manual
•The illustrations as shown in this manual are for instructional purposes only.
•The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.
■ About disposal
•This product contains recyclable components. When disposing of this product, please contact the appropriate local authorities.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Yamaha Corporation is under license.
The model number, serial number, power requirements, etc., may be found on or near the name plate, which is at the bottom of the unit. You should note this serial number in the space provided below and retain this manual as a permanent record of your purchase to aid identification in the event of theft.
Model No.
Serial No.
(bottom_en_01)
English
STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual |
5 |
Thank you for purchasing the Yamaha STAGEPAS 600BT/400BT Portable PA System! The STAGEPAS is an all-in-one portable PA system, consisting of two dedicated speakers and a powered mixer. It is designed to amplify music or speeches at live events or during other productions.
This owner’s manual explains how to set up and operate the STAGEPAS for use as a loudspeaker for music and speeches by individuals, companies, or schools. To get the most out of your new STAGEPAS and its sophisticated functions, we suggest that you read through this manual thoroughly, and keep it in a safe place for future reference.
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 NOTICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Model description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Attaching a speaker to a speaker stand . . . . . . . . . . . . . . . . . . .7 Attaching non-skid pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Controls and Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Quick Start Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Using a Bluetooth® device . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Features
•High-output power amplifier for versatility in a wide variety of performance applications.
•Two-way bass-reflex type speakers for high-quality, powerful sound.
•Multi-channel mixer supports a wide range of inputs.
•Bluetooth input for wireless high-quality sound from smartphones or tablets.
•Yamaha’s high-quality SPX reverb, which provides optimum processing for instruments or vocals.
•Feedback Suppressor, which automatically cuts and prevents undesirable feedback noise.
•Independent equalizer on each channel for tonal adjustment and sound control.
Package Contents (Please confirm that all items are included.)
•Main unit
(Dedicated speakers (STAGEPAS 600BT: MODEL 600S, STAGEPAS 400BT: MODEL 400S) x 2, powered mixer x 1)
•Power cord (2m) x 1
•Speaker cables (6m) x 2
•Non-skid pads x 12
•Ferrite core x 2
•Cable tie x 2
•Owner’s Manual (this book)
6 STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual
There are two models of Bluetooth-enabled STAGEPAS. The following table describes the differences in mixer functions between these models.
Model name |
Line-in channels |
Equalizer |
STAGEPAS 600BT |
CH 5/6, CH7/8, CH9/10 |
HIGH, MID, LOW |
|
|
|
STAGEPAS 400BT |
CH 5/6, CH7/8 |
HIGH, LOW |
|
|
|
NOTE
This manual primarily uses the STAGEPAS 600BT for purposes of explanation.
Model description
1. |
Attach the speaker to the speaker stand with the lock lever moved up (release |
English |
|
||
|
position). |
|
2. |
Move the lock lever down to lock to the stand. |
|
1. Release
Lock lever
2. Lock
If you plan to lay the speaker flat on its side, attach the included non-skid pads in the locations indicated by arrows in the figure below.
STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual |
7 |
Controls and Functions
|
4 |
5 |
|
8 |
|
1 |
|
|
|
|
|
|
|
|
6 |
|
|
2 |
3 |
|
7 |
|
N |
|
|
0 |
G |
|
|
|
|
|
|
9 |
|
|
|
|
|
|
|
B |
|
A |
|
|
|
|
|
|
|
|
|
|
|
C |
H |
|
|
|
|
|
|
|
|
E |
|
D |
I |
|
|
F |
|
|
|
||
|
|
|
|
|
|
J |
|
K |
L |
M |
O |
1 Mic/Line input jacks (channels 1-4) |
|
|
2 MIC/LINE switches (channels 1-4) |
Connect microphones, guitars, electronic musical |
|
|
For low-level signals (including microphones), set the switch to the MIC (N) |
instruments or audio equipment. |
|
|
position. For high-level signals (including electronic instruments and audio |
Channels 3 and 4 provide combo jacks that |
XLR |
Phone |
equipment), set the switch to the LINE (O) position. |
support both XLR and phone plugs. |
|
||
|
|
|
8 STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual
3Hi-Z switch (channel 4)
This switch is used when connecting a device directly to the mixer without a DI (direct box) — for example, instruments with passive pickups, such as an acoustic-electric guitar or electric bass without a battery. This function is effective only for the phone jack input.
4Line (stereo) input jacks
STAGEPAS 600BT (channels 5/6, 7/8, 9/10) STAGEPAS 400BT (channels 5/6, 7/8)
Connect line-level devices such as electronic instruments, acoustic-electric guitars, CD players, and portable audio players. These
jacks support phone, RCA-pin, and stereo-mini |
RCA Pin |
Stereo Mini |
|
|
|
plugs. |
|
|
NOTE
For the channel 7/8 input (STAGEPAS 600BT), or for the channel 5/6 input (STAGEPAS 400BT), if both phone and RCA-pin jacks are used at the same time, the phone jack will take priority. For the channel 9/10 input (STAGEPAS 600BT), or the channel 7/8 (STAGEPAS 400BT), if both phone and stereo mini jacks are used at the same time, the stereo mini jack will take priority. The signal from the device connected to another jack will be muted. The signals from the Bluetooth device specified by the Bluetooth button 9are always mixed to channels 9/10 (STAGEPAS 600BT) or channels 7/8 (STAGEPAS 400BT).
5MONITOR OUT jacks
These connect to powered speakers for monitoring purposes, and output a mix of the signals from channels 1 to 9/10 (STAGEPAS 600BT) or channels 1 to 7/8
(STAGEPAS 400BT). You can adjust the output level using the MONITOR OUT control A. If only the L (MONO) jack is used, the signals from the L and R channels are mixed and output.
6SUBWOOFER OUT jack
This connects to a powered subwoofer, and outputs a mono signal. If this jack is in
use, the low frequencies below 120Hz to the SPEAKERS L/R jacks will be cut. The output level is linked to that of the MASTER LEVEL control L.
7REVERB FOOT SW jack
This connects to an unlatched-type footswitch, such as the Yamaha FC5. This can be useful for solo performers, since you can toggle the reverb on and off as needed with your foot.
8SPEAKERS L/R jacks
Use the included speaker cables to connect the dedicated speakers.
|
|
|
Controls and Functions |
|
|
9 Bluetooth button/LED |
|
|
|
||
|
|
|
|||
|
This button switches the Bluetooth function on or off. It is also used to pair |
English |
|||
|
(register) a Bluetooth device (page 15). The Bluetooth LED indicates the following |
||||
|
|
||||
|
status: |
|
|
|
|
|
|
|
|
|
|
|
LED |
|
Status |
|
|
|
Off |
|
Bluetooth off |
|
|
|
|||||
|
|
|
|
|
|
|
Lit steadily |
|
Bluetooth connected |
|
|
|
|
|
|
|
|
|
Flashing slowly |
|
Waiting for Bluetooth connection |
|
|
|
|
|
|
|
|
|
Flashing fast |
|
Pairing a Bluetooth device |
|
|
|
|
|
|
|
|
NOTE
The STAGEPAS enables you to pair (register) up to eight Bluetooth devices. Once the ninth Bluetooth device has been paired successfully, the pairing information for the Bluetooth device that was connected earliest will be deleted.
0PHANTOM (CH1/2) switch /LED
When this switch is on, the LED lights up, indicating that phantom power is available for channels 1 and 2. Turn this switch on to supply power to condenser microphones or a DI (direct box).
Notice
Follow the important precautions below to prevent noise and possible damage to external devices and the unit when you operate this switch.
•Be sure to leave this switch off if you do not need phantom power, or when you connect a device that does not support phantom power to channels 1 or 2.
•Do not connect/disconnect a cable to/from channels 1 and 2 while this switch is on.
•Turn the LEVEL control of the channels 1 and 2 to the minimum before operating this switch.
AMONITOR OUT control
Determines the signal level output from the MONITOR OUT jacks 5. The MASTER LEVEL control does not affect the MONITOR OUT signal.
BEqualizer controls (HIGH, MID*, LOW) *Only for STAGEPAS 600BT
This three-band equalizer adjusts the channel’s high, mid*, and low frequency bands. Setting the control to the “D” position produces a flat response in the corresponding band. Turning the control clockwise boosts the selected band. If you start getting feedback, turn the control back slightly.
CREVERB switch/LED
When this switch is on, the LED lights up, indicating that you can apply reverb. This switch is off when you turn on the unit. (Unlike other switches, this switch cannot be locked.)
STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual |
9 |
Controls and Functions
DREVERB TYPE/TIME control
Determines the reverb type and length. Turning the control to the right lengthens the time of the selected reverb type.
HALL: Simulated reverb of a large space, such as a concert hall.
PLATE: Simulated metal plate reverb, producing a more hard-edged and bright sound.
ROOM: Simulated acoustic ambience of a small room. ECHO: Echo effect suitable for vocals.
EREVERB controls (channels 1-4)
Determines the amount of reverb for each channel when the REVERB switch C is on.
FST/MONO switches
STAGEPAS 600BT (channels 5/6, 7/8, 9/10) STAGEPAS 400BT (channels 5/6, 7/8)
Setting the switch to ST (STEREO) (N) will assign the signals from the L and R channels to each left and right speaker and output each signal. Setting the switch to MONO (O) will mix the output of different L and R sources to output the same signal to both the left and right speakers. For keyboards with mono output, guitars, or other non-stereo sound sources, when the switch is set to MONO (O), the stereo input jacks can be conveniently used as multiple mono jacks.
GLEVEL meter
The LEVEL meter shows the level of output signal from the SPEAKERS L/R jacks.
Notice
If the unit is operated at a sufficiently high volume to make the LIMITER LED flashes continuously, the internal power amplifier section is being excessively overloaded and may malfunction. Reduce the output level with the MASTER LEVEL control so that the indicator flashes only briefly on the highest transient peaks.
HPOWER LED
This LED lights when the power is turned on by pressing the power switch.
IFEEDBACK SUPPRESSOR switch/LED
When this switch is on, the LED lights up, indicating that feedback is automatically suppressed. (This configuration utilizes a seven-band notch filter. When this switch or the power switch is off, the notch filter will be reset.)
JLEVEL controls
Use these controls to adjust the volume for each channel. To reduce noise, set any LEVEL controls on unused channels to the minimum.
KMASTER EQ (equalizer) control
Use this control to adjust the overall sound frequency balance. The center position “MUSIC” is a basic setting. If you turn the control counterclockwise, it will create an optimum setting for speech, cutting unneeded low range frequencies. If you turn the control clockwise, it will create an optimum setting for playback of sound sources, since the low range is boosted. If you turn the control further clockwise, the LED will light up, indicating that the bass boost function turns on, giving you an even more powerful bass tone.
LMASTER LEVEL control
Determines the volume of the signal output from the SPEAKERS L/R jacks. This allows you to adjust the overall volume without changing the relative volume balance among the various channels.
MVents
These are the vents for the cooling fan inside the mixer. Do not block the vents when in use.
NAC IN jack
Connect the included power cord here.
OP (power) switch
For turning the power of the mixer on (O) and off (N).
NOTE
Rapidly turning the unit on and off in succession may cause it to malfunction. After turning the unit off, wait for about 5 seconds before turning it on again.
10 STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual