YAMAHA DTX750K User Manual

DTX750K			Digital Musical Instruments Division
	Assembly Manual		©2011 Yamaha Corporation
			WW60710 110PO***.*01C0
		EN

This pamphlet describes the standard procedure for DTX750K assembly.

After assembling the parts and connecting the cords as shown below, you will be ready to turn on the drum trigger module.

Standard Assembly Example
PCY135	PCY155
(Cymbal Pad)	(Cymbal Pad)
CH750		CH750
(Cymbal Holder)
		(Cymbal Holder)
	XP80
RHH135	(Tom Pad)
(Real Hi-hat Pad)
DTX700 Drum		PCY135
Trigger Module
		(Cymbal Pad)
	XP100SD	CH755
		(Cymbal Holder)
	(Snare Pad)
		XP80
		(Tom Pad)
HS650A
(Hi-hat Stand)
	KP65
	(Kick Pad)
		RS700
	SS662	(Rack System)
	(Snare Stand)

IMPORTANT

•For assembly, you will require four individual packages – an RS700 Rack System, a DTP750C Pad Set, a DTP750P Pad Set, and a DTX700 Drum Trigger Module.

•This pamphlet describes how to attach the pads and drum trigger module to the RS700 Rack System. Before carrying out the procedures described below, ensure that you have correctly assembled the rack system as described in its assembly manual.

Before starting assembly, lay a drum mat (sold separately) on the floor. Alternatively, before setting up the HS650A Hi-hat Stand and KP65 Kick Pad, you can place the packages' cardboard boxes on the floor to protect it from damage.

PRECAUTIONS

Before using, please read this assembly manual, and use this product in a safe and proper manner.

*Please keep this manual in a safe place for future reference.

*Make sure to read the Assembly Manual of the Rack System and the Owner’s Manual of the Pad.

	WARNING	If this symbol is ignored and the equipment is used improperly,
		fatal injury to persons or serious damage could occur.

•Do not let small children assemble or set up this product by themselves, or they may be injured. Always assemble this product with adult supervision.

•Be careful with the edges of the Cymbal Holders and the Tom Holders. The sharp holder ends may result in injury.

•Be careful with the edges of the spurs attached to the Kick Pad and foot pedal. The sharp ends may result in injury.

•If this product is used with a Rack System or Cymbal Stand, make sure all bolts are tightened firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts may result in the rack overturning or parts dropping, causing injury.

•Always set the product on a flat and solid surface. Placement on a sloping, unstable surface or on steps may result in the product being unstable and subject to overturning.

•When setting up the product, please pay close attention to the handling and setting of cables. Carelessly placed cables may cause the user and others to trip and fall.

•Do not alter the product. Doing so may result in injury or damage/deterioration to the product.

•Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury.

If this symbol is ignored and the equipment is used improperly,

CAUTION there is a danger or injury to persons handling the equipment, and material damage could occur.

•Watch your fingers when adjusting clamps. They may become pinched, resulting in injury.

•Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your fingers.

•Do not put your hands or feet under the foot pedal or foot switch. They may be pinched, resulting in injury.

•Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury.

NOTICE

•Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Also, never place any heavy or sharp objects on the cable. Applying excessive force to the cable may result in damage to the cable, such as the wires being severed, etc.

•Do not step on or place heavy objects on the product. It may result in damage.

•Do not use or keep the product in places with extremely high temperature (places in direct sunlight, close to a heater, in a closed car, etc.) or high humidity (bathroom, outside on a rainy day, etc.). Doing so may result in deformation, discoloration, damage or deterioration.

•When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration or deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as not to let the water and detergent come into contact with the cushions used in the product; doing so may result in deterioration.

*Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.

Assemble the RS700 Rack System.

1 For details, refer to the assembly manual that came with the rack system.

2Check the contents of each package.

Package 1: DTP750C

 PCY135	 PCY155	 RHH135
Cymbal Pad (x2)	Cymbal Pad (x1)	Real Hi-hat Pad (x1)

						 HS650A
 CH750			 CH755			Hi-hat Stand (x1)
Cymbal Holder (x2)			Cymbal Holder (x1)

 10-channel snake cable (x1)

 Tuning key (x1)

PCY100, PCY135, and PCY155 Owner’s Manual (x1)

RHH135 Owner’s Manual (x1)

Assembly Manual (this pamphlet)

Stand base for the RHH135 (x1)

Hi-hat clutch for the RHH135 (x1)

Cable band for the RHH135 (x1)

Stoppers for the PCY135 and PCY155 (x3)

Felts for the PCY135 and PCY155 (x3)

Cable bands (x10)

Package 2: DTP750P

 XP100SD	 XP80	 SS662
Snare Pad (x1)	Tom Pad (x3)	Snare Stand (x1)

 KP65

Kick Pad (x1)

 Clamp bolts (x4)

 Clamp bolt S (x1)

XP100T, XP100SD, XP120T, and XP120SD Owner’s Manual (x1)

XP70 and XP80 Owner’s Manual (x1)

KP65 Owner’s Manual (x1)

Package 3: DTX700

 DTX700 Drum Trigger	 Module stand (x1)	 AC power adaptor*
Module (x1)		(x1)
	 Module stand
	fastening screws (x4)
		* May not be included de-
 DTX700 Owner’s Manual (x1)		pending on your particular
		area. Please check with

	 DTX700 Data List (x1)	your Yamaha dealer.
	 DVD (containing software)

3	Mount the pads and the drum trigger module on the rack system.
	As described below, mount the pads and the trigger module on the rack system, and then position the kick pad and the hi-hat.

Mounting the cymbal holders

1. Mount the cymbal holders (CH750 x 2, CH755 x 1) on the rack system as shown below.

CH750

CH755

CH750

Mounting the tom pad

XP80

1. Attach the clamp bolt to each of the tom pads and provisionally tighten (by 5 or 6 turns).

Clamp bolt (to be tightened in the direction shown)

Tom pad (rear side)

2. Mount the tom pads on the rack’s clamp rods. As shown below, ensure that the rod section is fully inserted into each pad’s mounting hole, and then fully tighten the clamp bolt.

Tom pad	Clamp rod
	Rod
	section

Insert

Clamp bolt

3. If necessary, use clamp bolts A to E to adjust the height and angle of any of the pads. When doing so, be sure to adjust one bolt at a time (i.e., loosen a bolt, adjust the pad, and then retighten before loosening another).

Clamp bolt B

Clamp bolt D

Clamp bolt E

Clamp bolt A

Clamp bolt C

Continued on other side