Toshiba SD-260SA, SD-260SV, SD-260SY User Manual

DIGITAL VIDEO

DVD VIDEO PLAYER

SD-260SV SD-260SA SD-260SY

OWNER’S MANUAL

Introduction

Connections

Basic playback

Advanced playback

Function setup

Others

2

16

24

32

50

60

© 2005 Toshiba Corporation

Introduction

SAFETY PRECAUTIONS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:	TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
	APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT
	INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO
	QUALIFIED PERSONNEL ONLY.
CAUTION:	This Digital Video Disc Player employs a Laser System.
	To ensure proper use of this product, please read this owner’s manual carefully and retain for
	future reference. Should the unit require maintenance, contact an authorized service location.
	Use of controls or adjustments or performance of procedures other than those specified herein
	may result in hazardous radiation exposure.
	To prevent direct exposure to laser beam, do not try to open the enclosure.
	Visible and invisible laser radiation when open and interlocks defeated.
	DO NOT STARE INTO BEAM.

CLASS 1

LASER PRODUCT

In the spaces provided below, record the Model and Serial No. located on the rear panel of your DVD video player.

Model No.		Serial No.

Retain this information for future reference.

2

Location of the required label

Introduction

The rating plate and the safety caution are on the rear of the unit.

3

Introduction

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS GIVEN IN THIS OWNER’S MANUAL AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.

This set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this unit will protect you if you observe the following procedures for installation, use and servicing. This unit is fully transistorized and does not contain any parts that can be repaired by the user.

DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

4

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Introduction

8.Do not restrict the air flow of the unit by placing it in a place with poor air flow, by covering it with a cloth, or by placing it on carpeting.

9.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

S3125A

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

5

Introduction

IMPORTANT SAFETY INSTRUCTIONS

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

ADDITIONAL SAFETY INSTRUCTIONS

15.When you use headphones, keep the volume at a moderate level. If you use the headphones continuously with high volume sound, it may cause hearing damage.

16.Do not overload wall outlets; extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

17.Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

18.Keep your fingers well clear of the disc tray as it is closing. Neglecting to do so may cause serious personal injury.

6

19.Do not place a heavy object on or step on the apparatus. The object may fall, causing serious personal injury and serious damage to the apparatus.

Introduction

20.Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personal injury and apparatus malfunction.

21.Be sure to use the unit near the wall outlet. If a malfunction occurs, disconnect the plug from the wall outlet at once.

22.The mains plug is used as the disconnect device, the disconnect device shall remain readily operable at any time.

7

Introduction

Precautions

Notes on handling

Notes on moisture condensation

When shipping the DVD video player, the original shipping carton and packing materials come in handy. For maximum protection, repack the unit as it was originally packed at the factory. Take care not to give it a shock or shake when carrying.

Do not use volatile liquids, such as insect spray, near the DVD video player. Do not leave rubber or plastic products in contact with the DVD video player for a long time. They will leave marks on the finish.

The top and rear panels of the DVD video player may become warm after a long period of use. This is not a malfunction.

When the DVD video player is not in use, be sure to remove the disc and turn off the power.

If you do not use the DVD video player for a long period, the unit may not function properly in the future. Turn on and use the DVD video player occasionally.

Notes on locating

Place the DVD video player on a level surface. Do not use it on a shaky or unstable surface such as a wobbling table or inclined stand. The loaded disc may come off the proper position and cause damage to the DVD video player.

When you place this DVD video player near a TV, radio, or VCR, the playback picture may become poor and the sound may be distorted. In this case, place the DVD video player away from the TV, radio, or VCR.

Notes on cleaning

Use a soft, dry cloth for cleaning.

For stubborn dirt, soak the cloth in a weak detergent solution, wring well and wipe. Use a dry cloth to wipe it dry.

Do not use any type of solvent, such as thinner and benzine, as they may damage the surface of the DVD video player.

If you use a chemical saturated cloth to clean the unit, follow that product’s instructions.

To obtain a clear picture

The DVD video player is a high technology, precision device. If the optical pick-up lens and disc drive parts are dirty or worn down, the picture quality becomes poor. To obtain a clear picture, we recommend regular inspection and maintenance (cleaning or parts replacement) every 1,000 hours of use depending on the operating environment. For details, contact your nearest dealer.

Moisture condensation damages the DVD video player. Please read the following carefully.

Moisture condensation occurs, for example, when you pour a cold drink into a glass on a warm day. Drops of water form on the outside of the glass. In the same way, moisture may condense on the optical pick-up lens inside this unit, one of the most crucial internal parts of the DVD video player.

Moisture condensation occurs during the following cases.

When you bring the DVD video player directly from a cold place to a warm place.

When you use the DVD video player in a room where you just turned on the heater, or a place where the cold wind from the air conditioner directly hits the unit.

In summer, when you use the DVD video player in a hot and humid place just after you move the unit from an air conditioned room.

When you use the DVD video player in a humid place.

Do not use the DVD video player when moisture condensation may occur.

If you use the DVD video player in such a situation, it may damage discs and internal parts. Remove the disc, connect the power cord of the DVD video player to the wall outlet, turn on the DVD video player, and leave it for two or three hours. After two or three hours, the DVD video player will have warmed up and evaporated any moisture. Keep the DVD video player connected to the wall outlet and moisture condensation will seldom occur.

8

Notes on Discs

On handling discs

Do not touch the playback side of the disc.

Playback side

Do not attach paper or tape to discs.

On cleaning discs

Structure of disc contents

Normally, DVD video discs are divided into titles, and the titles are sub-divided into chapters. VIDEO CDs and audio CDs are divided into tracks.

DVD video disc

DVD video disc

Title 1

Title 2

Chapter

Chapter 1

1 Chapter 2

Chapter 2 Chapter 3

VIDEO CD/audio CD

VIDEO CD/audio CD

Track 1

Track 2

Track 3

Track 4

Track 5

Fingerprints and dust on the disc cause picture and sound deterioration. Wipe the disc from the center outwards with a soft cloth. Always keep the disc clean.

If you cannot wipe off the dust with a soft cloth, wipe the disc lightly with a slightly moistened soft cloth and finish with a dry cloth.

Do not use any type of solvent such as thinner, benzine, commercially available cleaners or antistatic spray for vinyl LPs. It may damage the disc.

On storing discs

Do not store discs in a place subject to direct sunlight or near heat sources.

Do not store discs in places subject to moisture and dust such as a bathroom or near a humidifier. Store discs vertically in a case. Stacking or placing objects on discs outside of their case may cause warping.

Each title, chapter or track is assigned a number, which is called “title number”, “chapter number” or “track number” respectively.

There may be discs that do not have these numbers.

Notes on copyright

The unauthorized recording, use, distribution, or revision of copyrighted materials including, without limitation, television programs, videotapes, and DVDs, is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Introduction

9

Introduction

Notes on Discs (continued)

About this owner’s manual

This owner’s manual explains the basic instructions of this DVD video player. Some DVD video discs are produced in a manner that allows specific or limited operation during playback. As such, the DVD video player may not respond to all operating commands. This is not a defect in the DVD video player. Refer to instruction notes of discs.

“ ” may appear on the TV screen during operation.

A “ ” means that the operation is not permitted by the DVD video player or the disc.

Notes on region numbers

The DVD video player is alloted one of region numbers, which stand for their playable area. If the numbers are printed on your DVD video disc, and are different from that of the DVD video player, disc playback will not be allowed by the player. (In this case, the DVD video player will display message on screen).

The region number of this DVD video player is printed on the rear panel of the main unit and on the carton.

DVD discs printed with can also be played back in this DVD disc player.

If the DVD disc does not have any region number printed, the disc playback is not guaranteed.

On VIDEO CDs

This DVD video player supports VIDEO CDs equipped with the PBC (Version 2.0) function. (PBC is the abbreviation of Playback Control.) You can enjoy two playback variations depending on types of discs.

•VIDEO CD not equipped with PBC function (Version 1.1)

Sound and movie can be played on this DVD video player in the same way as an audio CD.

•VIDEO CD equipped with PBC function (Version 2.0)

In addition to operation of a VIDEO CD not equipped with the PBC function, you can enjoy playback of interactive software with search function by using the menu displayed on the TV screen (Menu Playback). Some of the functions described in this owner’s manual may not work with some discs.

Playable discs

This DVD video player can play the following discs.

	Disc Mark		Contents	Disc	Maximum
				Size	playback time
					Approx. 4 hours
					(single sided disc)
			Audio	12 cm
					Approx. 8 hours
DVD			+		(double sided disc)
			video
video
			(moving
discs					Approx. 80 minutes
			pictures)
					(single sided disc)
				8 cm
					Approx. 160 minutes
					(double sided disc)
			Audio	12 cm	Approx. 74 minutes
VIDEO			+
			video
CDs
	DIGITAL VIDEO		(moving
			pictures)
				8 cm	Approx. 20 minutes
				12 cm	Approx. 74 minutes
Audio			Audio
CDs				8 cm
				(CD	Approx. 20 minutes
				single)

The following discs are also available.

DVD-R/DVD-RW discs of DVD video format

CD-R/CD-RW discs of CD-DA, Video CD, MP3, WMA or JPEG format

Some of these discs may be incompatible.

•You cannot play discs other than those listed above.

•You cannot play DVD-RAM discs or non-standardized discs, etc., even if they may be labeled as above.

•This DVD video player uses the NTSC/PAL color system, and cannot play DVD video discs recorded in any other color system (SECAM, etc.).

10

Table of Contents

Introduction
SAFETY PRECAUTIONS ..........................	2
IMPORTANT SAFETY INSTRUCTIONS ...	4
Precautions ..............................................	8
Notes on Discs .........................................	9
Notes on region numbers ...............................	10
Table of Contents ...................................	11
Identification of Controls .......................	12
Front panel .....................................................	12
Rear panel ......................................................	12
Remote control ...............................................	13
Loading batteries ...........................................	14
Operating with the remote control ..................	14
Connections
Connecting to a TV .................................	16
Connecting to a TV .........................................	16
Connecting to an audio system and TV
equipped with component video inputs .......	17
Connecting to Optional Equipment ......	18
Connecting to an amplifier equipped with a
Dolby Digital decoder ...................................	19
Connecting to an amplifier equipped with
Dolby Surround Pro Logic ............................	19
Connecting to an amplifier equipped with a
DTS decoder ................................................	19
Connecting to an amplifier equipped with an
MPEG2 audio decoder .................................	20
Connecting to an amplifier equipped with a
digital audio input .........................................	21
Basic playback
Playing a Disc .........................................	24
Basic playback ...............................................	24
Variable Speed Playback .......................	26
Playing in fast reverse or fast forward
directions ......................................................	26
Playing frame by frame ..................................	26
Playing in slow-motion ...................................	27
Resuming playback from the same location ..	27
Locating a Desired Section ...................	28
Locating a title using the top menu ................	28
Locating a desired section by entering the
corresponding number .................................	29
Locating a specific chapter or track ...............	29

Advanced playback

Accessing a Specific Location Directly ... 32

Entering the time counter of the desired
location .........................................................	32
Repeating a Specific Segment ..............	33
Repeating a specific segment ........................	33
Playing in a Varied Order .......................	34
Playing titles, chapters or tracks in a varied
order .............................................................	34
Playing in a Favourite Order ..................	35
Setting titles, chapters, or tracks in a favourite
order .............................................................	35
Zooming a Picture ..................................	36
Zooming a picture ..........................................	36
Selecting the Picture Enhancement
(E.P.M.) ....................................................	37
Selecting the picture enhancement ................	37
Selecting the Sound Enhancement
(E.A.M.) ...................................................	38
Selecting the sound enhancement .................	38
Selecting the Camera Angle ..................	39
Changing the camera angle ...........................	39
Selecting Subtitles .................................	40
Selecting a subtitle language .........................	40
Selecting a Language ............................	41
Selecting a playback audio setting .................	41
On-screen Display Operation ................	42
On-screen display operation ..........................	42
Playing MP3/WMA Files .........................	44
Playing MP3/WMA files ..................................	44
Viewing JPEG Files ................................	46
Viewing JPEG files .........................................	46
Viewing a thumbnail view ...............................	47
Function setup
Customizing the Function Settings ......	50
Setting procedure ...........................................	50
Setting details .................................................	52
Table of Languages ................................	57
Others
Before Calling Service Personnel .........	60
Specifications .........................................	61

Introduction

11

Introduction

Identification of Controls

See the page in for details.

Front panel

24		24
			14
		24	29
				24
			25
Rear panel
16
		17
	19	20	21
16	17
		16
12

Identification of Controls (continued)

The instructions in this manual describe the functions on the remote control. See the page in for details.

Remote control

24

43

42

39

28

40

28

29

25

29

26

17

38

24

24

36

41

28

50

25 26

24

29

26

27 37

29

29
50	33
35	34

* MENU button

Use the MENU button to display the menu included on many DVD video discs. To operate a menu, follow the instructions in “Locating a title using the top menu.”

28

Introduction

13

Introduction

Loading batteries

1 Open the cover.

2 Insert batteries (R03/AAA size).

Make sure to match the + and – on the batteries to the marks inside the battery compartment.

Caution

• Never throw batteries into fire.

Notes

•Be sure to use R03/AAA size batteries.

•Dispose of batteries in a designated disposal area.

•Attention should be drawn to the environmental aspects of battery disposal.

•Do not mix different battery types or combine used batteries with new ones.

•If the remote control does not operate correctly, or if the operating range becomes reduced, replace both batteries with new ones.

•If the batteries are dead or if you will not be using the remote control for a long time, remove the batteries to prevent battery acid from leaking into the battery compartment.

Operating with the remote control

Point the remote control at the remote sensor and press the buttons.

Distance: About 7 m (23 feet) from the front of the remote sensor

Angle: About 30° in each direction of the front of the remote sensor

*Do not expose the remote sensor of the DVD video player to a strong light source such as direct sunlight or other illumination. If you do so, you may not be able to operate the DVD video player via the remote control.

Notes on the remote control

•Direct the remote control at the remote sensor of the DVD video player.

•When using the remote control, press the buttons at intervals of about 1 second to ensure the correct mode of operation.

•Do not drop or give the remote control a shock.

•Do not leave the remote control near an extremely hot or humid place.

•Do not spill water or put anything wet on the remote control.

•Do not open the remote control.

14

Introduction

Connections

Read this chapter first to make all necessary preparations.

Connecting to a TV

Connecting to an audio system and TV equipped with component video inputs

Connecting to an amplifier equipped with a Dolby Digital decoder

Connecting to an amplifier equipped with Dolby Surround Pro Logic

Connecting to an amplifier equipped with a DTS decoder

Connecting to an amplifier equipped with an MPEG2 audio decoder

Connecting to an amplifier equipped with a digital audio input

15

Connections

Connecting to a TV

Connect the DVD video player to your TV.

For details of output sound, see 41 .

Connecting to a TV

• Make the following setting.

	On-screen display	Select:	Page
	“Digital Output”	“PCM” or	50	55
		“Bitstream”
	“Video Output”	Composite	50	54
		* Component

* Only for analog video out jack (yellow) connection with progressive scan off.

Notes

•Refer to the owner’s manual of the connected TV as well.

•When you connect the DVD video player to your TV, be sure to turn off the power and unplug both units from the wall outlet before making any connections.

•If your television set has one audio input, connect the left and right audio outputs of the DVD video player to a Y cable adapter (not supplied) and then connect to your TV.

•Connect the DVD video player directly to your TV. If you connect the DVD video player to a VCR, TV/VCR combination or video selector, the playback picture may be distorted as DVD video discs are copy protected.

•Analog audio out will not have sound if DTS playback is selected.

16

Interlaced outputs

Some TVs or monitors are equipped with component video inputs. Connecting to these inputs allows you to enjoy higher quality picture playback.

Actual labels for component video inputs may vary depending on the TV manufacturer. (ex. Y, R-Y, B-Y or Y, CB, CR)

In some TVs or monitors, the color levels of the playback picture may be reduced slightly or the tint may change. In such a case, adjust the TV or monitor for optimum performance.

Progressive outputs

Some TVs or monitors are equipped with component video inputs that are capable of reproducing a progressively scanned video signal. Connecting to these inputs allows you to view the highest quality pictures with less flicker.

Consumers should note that not all high definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of 525 progressive scan picture problems, it is recommended that the user switch the connection to the “standard definition” output. If there are questions regarding our TV set compatibility with this model 525p DVD player, please contact our Customer Service Center.

Connecting to an audio system and TV equipped with component video inputs

Connections

Switching the output signal (interlaced/progressive) using the remote control

You can temporarily switch the output signal for better picture quality.

Press PROGRESSIVE on the remote control during stop mode. Press PROGRESSIVE again to turn off progressive mode.

Notes

• Make the following setting.

On-screen display	Select:	Page
“Digital Output”	“PCM” or	50	55
	“Bitstream”
“Video Output”	Component	50	54

•Refer to the owner’s manual of the connected equipment as well.

•When you connect the DVD video player to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connections.

•If you place the DVD video player near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the DVD video player away from the tuner and radio.

•The output sound of the DVD video player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening level. Otherwise, high volume sound may damage your hearing as well as the speakers.

•Turn off the amplifier before you connect or disconnect the

DVD video player’s power cord. If you leave the amplifier power on, the speakers may be damaged.

•Progressive can be on/off only when “Video Output” is set to Component 54 .

•In component connections, the screen might become pinkish in color when the “Video Output” is set to

Composite. This is not a defect of this unit 54 .

•When Progressive is on, only component video will be output.

•Analog audio out will not have sound if DTS playback is selected.

•When using component video cables, do not connect the S video cable.

•When the TV system is set to NTSC mode, all output will be forced to NTSC type (eg. 525p, 525i) 54 .

•When the TV system is set to PAL mode, progressive scan will be prohibited. All output will be forced to PAL type (eg. 625i) 54 .

•When the TV system is set to Auto mode and Video

Output is set to Component, all component output will be forced to NTSC type (e.g. 525p, 525i ) 54 .

17

Connections

Connecting to Optional Equipment

You can enjoy high quality dynamic sounds by connecting the DVD video player to optional audio equipment.

• For connection to your TV, see “Connecting to a TV”

16 17 .

• For details of output sound, see 41 .

• This section uses the following reference marks.

: Front speaker

: Rear speaker

: Sub woofer

: Center speaker

: Signal flow

Notes

•DO NOT connect the COAXIAL DIGITAL AUDIO OUT jack of the DVD video player to the AC-3 RF input of a

Dolby Digital Receiver. This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the COAXIAL DIGITAL AUDIO OUT jack of the DVD video player.

•Connect the COAXIAL DIGITAL AUDIO OUT jack of the

DVD video player to the “DIGITAL (COAXIAL)” input of a

Receiver or Processor.

•Refer to the owner’s manual of the connected equipment as well.

•When you connect the DVD video player to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connections.

•The output sound of the DVD video player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.

•Turn off the amplifier before you connect or disconnect the DVD video player’s power cord. If you leave the amplifier power on, the speakers may be damaged.

Warning

•When you are connecting (via the COAXIAL DIGITAL AUDIO OUT jack) an AV decoder that does not have Dolby Digital, Digital Theater Systems (DTS) or MPEG2 decoding function, be sure to set “Digital Output” to

“PCM” from the on-screen displays 50 55 . Otherwise, high volume sound may damage your hearing as well as the speakers.

•When playing DTS-encoded discs (audio CDs), excessive noise may be output from the analog audio output jacks. To avoid possible damage to the audio system, you should take proper precautions when the analog audio output jacks of the DVD video player are connected to an amplification system. To enjoy DTS Digital Surround™ playback, an external 5.1 channel

DTS Digital Surround™ decoder system must be connected to the COAXIAL DIGITAL AUDIO OUT jack of the DVD video player.

18

Connecting to an amplifier equipped with a Dolby Digital decoder

Dolby Digital

Dolby Digital is the surround sound technology used in theaters showing the latest movies, and is now available to reproduce this realistic effect in the home. You can enjoy motion picture and live concert DVD video discs with this dynamic realistic sound by connecting the DVD video player to a 6 channel amplifier equipped with a Dolby Digital decoder or Dolby Digital processor. If you have a Dolby Surround Pro Logic decoder, you will obtain the full benefit of Pro Logic from the same DVD movies that provide full 5.1-channel Dolby Digital soundtracks, as well as from titles with the Dolby Surround mark.

Amplifier equipped with a

Dolby Digital decoder

To COAXIAL type

digital audio input To COAXIAL DIGITAL AUDIO

OUT

Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. Confidential unpublished works. Copyright 1992-1997 Dolby Laboratories. All rights reserved.

•Use DVD video discs encoded via the Dolby Digital recording system.

•Make the following setting.

	On-screen display	Select:	Page
	“Digital Output”	“Bitstream” or	50
		“PCM”	55
	Recording system	D	41

75 Ω coaxial cable

Connecting to an amplifier equipped with Dolby Surround Pro Logic

Dolby Surround Pro Logic

You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by connecting an amplifier and speaker system (right and left front speakers, a center speaker, and one or two rear speakers).

With an amplifier equipped with Dolby Digital

Connect the equipment the same way as described in “Connecting to an amplifier equipped with a Dolby Digital decoder.” Refer to that amplifier’s owner’s manual and set the amplifier so you can enjoy Dolby Surround Pro Logic sound.

With an amplifier not equipped with Dolby Digital

Connect the equipment as follows.

*	Amplifier equipped with
	Dolby Surround Pro Logic
	To audio input	To ANALOG
		AUDIO OUT

• Make the following setting.

	On-screen display	Select:	Page
	“Digital Output”	“Bitstream” or	50
		“PCM”	55

* Connect one or two rear speakers. The output sound from the rear speakers will be monaural even if you connect two rear speakers.

Audio cable

Connections

19