CLT-9911-16E 3/14/03 3:40 PM Page 1
INSTRUCTION CLT-9911
MANUAL
CLT-9916
900-MHz
Cordless Telephone
IMPORTANT
Charge the handset battery for 12 continuous hours prior to first use.
The exclamation point within the triangle is a warning sign alerting you of important instructions accompanying the product.
SANYO Canada Inc.
www.sanyocanada.com
INTRODUCTION
Congratulations on your purchase of this Sanyo cordless telephone.
Your Sanyo 900-MHz cordless telephone is a finequality home communications product. It is carefully designed and produced by a world leader of consumer and industrial electronics equipment. With proper maintenance and care, it will provide you with years of enjoyment and convenience.
Main Features
900-MHz Technology
Extended Range -The use of 900-MHz frequency band for signal transmission between base and handset means greater communication range compared to conventional 43 – 49 MHz cordless telephones. Ultra-Low Noise -The high frequency communication has also significantly reduced noise level.
40-Channel Auto/Manual Scan -Your new telephone uses one of 40 channels in the 900-MHz frequency band. It automatically selects a clear channel every time you receive or place a call on the handset.
COMPANDER PLUS Noise Reduction
This fourth generation of the Sanyo’s original noise reduction technology now filters out more background noise.
•10-number speed dial memory
•Lighted keypad (CLT-9916 only)
•Ringer on/off switch
•Voice mail waiting indicator*
•Wall-mountable
•Belt clip (CLT-9916 only)
*Important:
Reuires a subscription to digital voice mail box provided by your local telephone company.
GETTING STARTED
Checking the package contents
Make sure your package includes the items shown here.
Base |
Handset |
AC |
|
|
adaptor |
Telephone |
Belt clip |
A10920 |
line cord |
(CLT-9915 only) |
Replacement Battery Order Form
Modular jack
To properly connect your phone to your telephone lines, you will need an RJ11 type modular phone jack. If you do not have a modular jack, call your local phone company to find out how to get one installed.
Installation note: Avoid places near electrical equipment such as refrigerators, computers, TVs or fluorescent lamps. These may cause interference or reduce the operating range of the cordless telephone.
Digital Security System
Your cordless phone uses a digital security system to provide protection against false ringing, unauthorized access and charges to your phone line.
When you place the handset in the base, the unit verifies its security code. After a power outage or battery replacement, place the handset in the base for about 20 seconds to reset the code.
CLT-9911-16E 3/14/03 3:40 PM Page 2
INSTALLATION
Connections
1 RINGER
ON
2
3
1.Set the RINGER switch on the front of handset to ON and place the handset in the base.
2.Plug the AC adaptor into the POWER 9V DC jack on the bottom of the base and the other end into an electrical outlet. The VOICE MAIL/CHARGE/ IN USE indicator lights, verifying the battery is charging.
Charge the handset battery for 12 continuous hours prior to first use. The initial, uninterrupted battery charge is important for best performance.
Note: The handset can be charged facing up or down.
Low Battery Warning: When the battery is low you will hear a short beep every 7 seconds. Please follow the same steps as above to recharge your battery for best performance.
Important: Do not connect the telephone line to the modular jack until the phone has been charged for 12 continuous hours.
3.Plug the telephone line cord into the PHONE LINE jack on the bottom of the base and into a modular jack.
Caution: Use only Sanyo AC adaptor, A10920, that came with this phone. Using other adaptors may damage the phone.
Note: The phone automatically defaults to touch tone dialing. To change to pulse (rotary) dialing, see Tone/Pulse setting. If you do not know which type of service you have, check with your telephone company.
Mounting on a wall
Do not attempt to wall-mount the phone before initial 12-hour charging is completed.
RINGER 1
ON
4
3
2
1.Follow steps 1–2 above to charge the handset. Wait at least 12 hours.
2.Plug the telephone line cord into the PHONE LINE jack on the bottom of the base and the other end into a modular jack.
3.Slip the mounting holes on the bracket over the wall plate posts and firmly slide the base down into place (wall plate not included).
4.Place the handset in the base.
Note: If desired, gather the extra line cord together, and fasten with a wire tie.
CLT-9911-16E 3/14/03 3:40 PM Page 3
NAMES AND CONTROLS
VOL (volume)
▼ key
REDIAL key
MEM (memory) key
TONE key
CHAN (channel) key
TALK key
VOL (volume)
▲ key
PAUSE key
FLASH/
PROG (program) key
Ringer switch:
RINGER ON/OFF
TONE/PULSE setting
The dialing mode of your telephone is set to TONE at factory.
To change it to PULSE mode:
1.Make sure the phone is off (not in TALK mode).
2.Press FLASH/PROG twice.
3.Press number 2 key to select PULSE dialing.
4.Press FLASH/PROG twice to confirm.
BASICS
Receiving a call
Press TALK.
Ringer switch
The RINGER switch must be ON for the handset to ring during incoming calls.
Volume
While talking, press VOL keys ( ▲ and ▼ ) to control the receiver volume.
There are four volume levels. Press ▲ to increase the volume level, and press ▼ to decrease.
Making a call
Press TALK before you dial and press it again to hang up.
Redialing a call
Press TALK and then REDIAL to redial the last number you dialed (up to 32 digits). If you get a busy signal, and want to keep dialing the number, just press REDIAL again (you do not have to turn the phone off and back on).
FLASH key
Use the FLASH/PROG key to use special calling services such as Call Waiting or Call Transfer. You must subscribe to these services available through your local phone company.
Tip: Do not use TALK to activate custom calling services or you’ll hang up the phone.
VOICE MAIL/CHARGE/IN USE indicator
•Flashes when you have a new voice mail
• Lights when the handset is being charged in the base
• Lights when the handset is in use.
Voice mail
When you subscribe to a voice mail service offered by your phone company, the VOICE MAIL/ CHARGE/IN USE indicator on the base flashes to indicate there is voice mail waiting. After the voice mail has been reviewed. the indicator stops flashing.
This indicator does not work with your answering machine.
Note: The phone will only work with an FSK type of VMWI system. It will not work with the Stutter Dial Tone type of VMWI system.
CHAN (Channel) key
Press and release CHAN to advance to the next channel to get rid of static while talking.
Temporary tone
This feature enables pulse (rotary) service phone users to access touch-tone services offered by banks, credit card companies, etc.
1.Call the bank’s information line.
2.Press TONE after your call is connected.
3.Follow the voice instructions to complete your transaction.
4.Hang up when finished. The phone returns to pulse (rotary) service.
Handset locator
This feature helps to locate a misplaced handset. Press PAGE on the base. The handset beeps continuously for about two minutes or until you press any key on the handset. Press PAGE to cancel.
Note: The RINGER switch does not have to be ON for this feature to work.
Loading...