Samsung DV220AGW/XAA, DV220AEW/XAA, DV210AGW/XAA, DV210AEW/XAA User Manual

DV210A*

DV220A*

Gas and Electric Dryer

user manual

This manual is made with 100% recycled paper.

imagine the possibilities

Thank you for purchasing this Samsung product. To receive more complete service or accessory parts, please register your product at or contact

www.samsung.com/register

1-800-SAMSUNG (726-7864)

DV220AE-02810A-10_EN.indd 1

2013-04-23 3:39:45

features

1. Extra Large Capacity

Ultra drying capabilities are at your fingertips! Now you can dry extra-large loads. Our ultra large 7.3 cu.ft. capacity dryer circulates more air through your clothes, drying them faster for a wrinkle-free result.

2. Various Drying Cycles & Fuzzy Logic Algorithm

Simply turn the Jog Dial to select one of the 7 automatic drying cycles, including normal and heavy duty, or let the Fuzzy Logic Control measure the degree of dampness and

automatically set the drying time. Precision drying has never been easier than with Samsung.

3. Time Saving

Our cycles are designed with you in mind. All our dryers are designed to dry your clothes in less time... just 42 minutes! Giving you time for more important things in life.

4. Energy Saving

Samsung dryers are super energy efficient. You can dry up to 3.01 pounds of laundry with 1kWh. Also, both the large capacity and Fuzzy Logic Control save energy by automatically drying your clothes the most efficient way.

5. Easy Reversible Door

Our dryers will fit just about anywhere. The direction of our easy reversible door can be changed with just four screws.

6. Pedestal with Storage Drawers

An optional 15” pedestal is available to raise the dryer for easier loading and unloading. It also offers a built-in storage drawer that can hold a 100 oz. bottle of detergent

7. Stacking (MODEL NO: SK-3A1, SK-4A, SK-5A)

Samsung’s Washers and Dryers can be stacked to maximize usable space.

The Dryer legs need to be removed to stack the Washer and Dryer. An optional stacking kit is available for purchase from your Samsung retailer.

8. 4-way Vent (electric model only)

You can install the exhaust vent in the following four (4) positions: back, either side, bottom.

2_ features

DV220AE-02810A-10_EN.indd Sec9:2

2013-04-23 3:39:49

safety instructions

Congratulations on your new Samsung Dryer. This manual contains valuable information on the installation, use, and care of your appliance. Please take the time to read this manual to take full advantage of your dryer’s many benefits and features.

WARNING - Risk of Fire

•Clothes dryer installation must be performed by a qualified installer.

•Install the clothes dryer according to the manufacturer’s instructions and local codes.

•Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire.

•To reduce the risk of severe injury or death, follow all installation instructions.

WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS

Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur. It is your responsibility to use common sense, caution, and care when installing, maintaining, or operating your dryer.

Always contact your manufacturer about problems or conditions you do not understand.

IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS

Hazards or unsafe practices that may result in severe personal injury or death.

WARNING

Follow the information in this manual to minimize the risk of fire or explosion or to prevent property damage, personal injury, or death.

Do not store or use gasoline or other flammable vapors and liquids near this or any other appliance.

Hazards or unsafe practices that may result in minor personal injury or

property damage.

CAUTION

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions explicity.

Unplug the power plug from the wall socket.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

SAVE THESE INSTRUCTIONS

safety instructions _3

DV220AE-02810A-10_EN.indd Sec1:3

2013-04-23 3:39:49

safety instructions

IMPORTANT SAFTY INSTRUCTION

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your WARNING appliance, follow basic precautions, including the following:

1.Read all instructions before using this appliance.

2.Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode.

3.Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children.

4.Before the appliance is removed from service or discarded, remove the door to the drying compartment.

5.Do not reach into the appliance if the drum is moving.

6.Do not install or store this appliance where it will be exposed to the weather.

7.Do not tamper with controls.

8.Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published userrepair instructions that you understand and have the skills to carry out.

9.Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

10.Clean lint screen before or after each load.

11.Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.

12.Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt.

13.The interior of the appliance and exhaust duct should be cleaned periodically by qualified service personnel.

14.Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

State of California Proposition 65 Warnings:

WARNING

The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances known to the State of California to cause cancer, birth defects, or other reproductive harm, and requires businesses to warn of potential exposure to such substances.

This product contains a chemical known to the State of California to cause cancer, birth defects, or other reproductive harm. This appliance can cause low-level exposure to some of the substances listed, including benzene, formaldehyde, and carbon monoxide.

Gas appliances may cause low-level exposure to some of the substances listed including benzene, formaldehyde, carbon monoxide, and soot; as a result of possible incomplete combustion of natural gas or LP fuels. Exposure to these substances can be minimized further by properly venting the dryer to the outdoors.

SAVE THESE INSTRUCTIONS

4_ safety instructions

DV220AE-02810A-10_EN.indd Sec1:4

2013-04-23 3:39:49

WHAT TO DO IF YOU SMELL GAS:

•Do not try to light any appliance.

•Do not turn on the appliance.

•Do not touch any electrical switch.

•Do not use any phone in your building.

•Clear the room, building or area of all occupants.

•Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

•If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

Read all instructions before using the appliance.

To reduce the risk of fire or explosion:

WARNING

•Do not dry items that have been previously cleaned, washed, soaked, or spotted with gasoline, dry cleaning solvents, or other flammable or explosive substances. They emit vapors that could ignite or explode. Any material that has been in contact with a cleaning solvent or flammable liquids or solids should not be placed in the dryer until all traces of these flammable liquids or solids and their fumes have been removed.

There are many highly flammable items used in homes, such as acetone, denatured alcohol, gasoline, kerosene, some liquid household cleaners, some spot removers, turpentine, waxes, and wax removers

•Items containing foam rubber (may be labeled latex foam) or similarly textured rubberlike materials must not be dried on a heat setting. Heated foam rubber materials can, under certain circumstances, produce fire by spontaneous combustion.

Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is necessary when the appliance is used near children and pets.

Before discarding or removing your dryer from service, remove the door to the drying compartment to prevent children or animals from becoming trapped inside.

Do not reach into the appliance when the drum is moving.

Do not install or store this appliance where it will be exposed to the weather.

Do not tamper with controls.

Do not repair, replace, or attempt to service any part of the appliance unless specifically recommended in the user-repair instructions and you understand and have the skills to carry those out.

Do not use fabric softeners or products to eliminate static unless recommended for dryer use by the manufacturer of the fabric softener or product.

Clean the lint screen before or after each load.

Keep the area around the exhaust opening and surrounding areas free from lint, dust, and dirt.

The interior of the dryer and exhaust duct should be cleaned periodically by qualified service personnel.

SAVE THESE INSTRUCTIONS

safety instructions _5

DV220AE-02810A-10_EN.indd Sec1:5

2013-04-23 3:39:49

safety instructions

This appliance must be properly grounded. Never plug the power cord into a receptacle that is not grounded adequately and in accordance with local and national codes. See installation instructions for grounding this appliance.

Do not sit on top of the dryer.

Because of continuing product improvements, Samsung reserves the right to change specifications without notice. For complete details, see the Installation Instructions packed with your product before selecting cabinetry, making cutouts, or beginning installation.

Ensure pockets are free from small irregularly shaped hard objects, foreign material, etc. ie. WARNING coins, knives, pins, etc. These objects could damage your dryer.

Do not wash clothing with large buckles, buttons, or other heavy metal or solid things.

Gas leaks may occur in your system, resulting in a dangerous situation.

WARNING

Gas leaks may not be detected by smell alone.

Gas suppliers recommend you purchase and install a UL-approved gas detector.

Install and use in accordance with the manufacturer’s instructions.

Do not place items in your dryer that have been spotted or soaked with vegetable oil or cooking oil. Even after being washed, these items may contain significant amounts of these oils.

Residual oil on clothing can ignite spontaneously. The potential for spontaneous combustion increases when items containing vegetable oil or cooking oil are exposed to heat. Heat sources such as your dryer can warm these items, allowing an oxidation reaction in the oil to occur. Oxidation creates heat. If this heat cannot escape, the items can become hot enough to catch fire. Piling, stacking, or storing these kinds of items may prevent heat from escaping and can create a fire hazard.

All washed and unwashed fabrics that contain vegetable oil or cooking oil can be dangerous. Washing these items in hot water with extra detergent will reduce, but not eliminate, the hazard. Always use the Cool Down cycle for these items to reduce their temperature. Never remove these items from the dryer hot or interrupt the drying cycle until the items have run through the Cool Down cycle. Never pile or stack these items when they are hot.

SAVE THESE INSTRUCTIONS

6_ safety instructions

DV220AE-02810A-10_EN.indd Sec1:6

2013-04-23 3:39:49

contents

INSTALLING YOUR DRYER	8	Tools needed for installation
8	8	See Dryer Exterior
	9	Ducting requirements
	10	Important to installer
	10	Location considerations
	10	Alcove or closet installation
	11	Mobile home installation
	11	Exhausting
	12	Gas requirements
	13	Electrical requirements
	13	Grounding
	14	Electrical connections
	15	Replacement parts and accessories
	15	Installation
	17	Final installation checklist
	18	Dryer Exhaust Tips
	19	Door Reversal
OPERATING INSTRUCTIONS, TIPS	20	Overview of the control panel
20	22	Child lock
	23	Rack Dry (Optional Part)
	24	Clean the lint filter
	24	Load the dryer properly
	24	Getting started
CARE AND CLEANING	25	Control Panel
25	25	Tumbler
	25	Powder coated tumbler
	25	Dryer Exterior
	25	Dryer Exhaust System
SPECIAL LAUNDRY TIPS	26	Special laundry tips
26
TROUBLESHOOTING	27	Check these points if your dryer…
27	28	Information codes
APPENDIX	29	Fabric care chart
29	30	Protecting the environment
	30	Declaration of conformity
	30	Specifications
	31	Cycle chart

contents _7

DV220AE-02810A-10_EN.indd Sec3:7

2013-04-23 3:39:49

installing your dryer

TOOLS NEEDED FOR INSTALLATION

Hire a professional to install this dryer properly. If there is a service call performed as a result of poor setup, adjustment, and connection, it is considered the responsibility of the installer. If you install the dryer, you are responsible.

Make sure you have everything necessary for proper installation.

1.A GROUNDED ELECTRICAL OUTLET is required. See Electrical Requirements. See page 12.

2.A POWER CORD for electric dryers (except Canada). See page 13.

3.GAS LINES (if a gas dryer) must meet national and local codes.

4.EXHAUST SYSTEM – must be rigid metal or flexible stiff-walled metal exhaust ducting. See the exhaust requirements on pages 8-10.

SEE DRYER EXTERIOR

Drying Rack is not supplied in this model. The Drying Rack is optional. You can purchase it through a service center.

Control panel

Door

Adjustable legs

8_ installing your dryer

DV220AE-02810A-10_EN.indd Sec11:8

2013-04-23 3:39:49

DUCTING REQUIREMENTS

• Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct.
• Do not use a smaller duct.
• Ducts larger than 4 inches (10.2 cm) in diameter can result in increased lint accumulation.
Lint accumulation should be cleaned regularly.			01
• If a flexible metal duct must be used, use the type with a stiff sheet metal wall. Do not use a flexible duct
			installing
with a thin foil wall. Serious blockage can result if the flexible metal duct is bent too sharply.
• Never install any type of flexible duct in walls, ceilings, or other concealed spaces.
• Only a rigid or flexible metal duct should be used for exhausting.			your
• Keep the exhaust duct as straight and short as possible.
• Secure joints with duct tape. Do not use screws.			dryer
• DO NOT EXHAUST DRYER INTO ANY WALL, CEILING, CRAWL SPACE, OR CONCEALED SPACE OF
A BUILDING, GAS VENT, OR ANY OTHER COMMON DUCT OR CHIMNEY. THIS COULD CREATE A
FIRE HAZARD FROM LINT EXPELLED BY THE DRYER.
• A plastic flexible duct can kink, sag, be punctured, reduce airflow, extend drying times, and affect dryer
operation.
• Exhaust systems longer than recommended can extend drying times, affect machine operation, and
may collect lint.
• The exhaust duct should end with an exhaust hood with a swing-out damper to prevent back drafts and
entry of wildlife. Never use an exhaust hood with a magnetic damper.
• The hood should have at least 12 inches (30.5 cm) of clearance between the bottom of the hood and
the ground or other obstruction. The hood opening should point down.
• Never install a screen over the exhaust outlet.
• To avoid lint buildup, do not exhaust the dryer directly into a window well. Do not exhaust under a house
or porch.
• If exhaust ductwork must run through an unheated area, the duct should be insulated and slope slightly
down towards the exhaust hood to reduce condensation and lint buildup.
• Inspect and clean the interior of the exhaust system at least once a year. Unplug the power cord before
cleaning.
• Check frequently to be sure the exhaust hood damper opens and closes freely.
• Check once per month, and clean at least one time per year. Note: If clothes are not getting dry, then
check ducting for obstructions.
	ELECTRIC AND GAS DRYER
	Weather Hood Type
	Recommended	Use only for short-run installation

	4” (10.16 cm)		2.5” (6.35 cm)
No. of 90° elbows	Rigid	Metallic Flexible*	Rigid	Metallic Flexible*
0	24.4 m (80 ft.)	12.4 m (41 ft.)	22.6 m (74 ft.)	10.1 m (33 ft.)
1	20.7 m (68 ft.)	11.2 m (37 ft.)	18.9 m (62 ft.)	8.8 m (29 ft.)
2	17.4 m (57 ft.)	10.1 m (33 ft.)	15.5 m (51 ft.)	7.6 m (25 ft.)
3	14.3 m (47 ft.)	9.0 m (29 ft.)	12.5 m (41 ft.)	6.5 m (21 ft.)

*Do not use non-metallic flexible duct.

installing your dryer _9

DV220AE-02810A-10_EN.indd Sec11:9

2013-04-23 3:39:49

installing your dryer

If the new Dryer is installed into an existing exhaust system you must make sure:

•The exhaust system meets all local, state, and national codes.

•That a flexible plastic duct is not used.

•To Inspect and clean all lint buildup from inside the existing duct.

•The duct is not kinked or crushed.

•The exhaust hood damper opens and closes freely.

The static pressure in any exhaust system must not exceed 0.83 inches of water column, or be less than 0.

This can be measured while the Dryer is running with a manometer at the point where the exhaust duct connects to the Dryer. A no-heat setting should be used. The Dryer tumbler should be empty and the lint filter clean.

IMPORTANT TO INSTALLER

Please read the following instructions carefully before installing the dryer. These instructions should be kept for future reference.

REMOVE THE DOOR FROM ALL DISCARDED APPLIANCES TO AVOID THE DANGER OF A CHILD WARNING SUFFOCATING.

LOCATION CONSIDERATIONS

The dryer should be located where there is enough space at the front for loading the Dryer, and enough space behind for the exhaust system. This Dryer is factory-ready for rear exhaust. To exhaust out the bottom or the left, use the accessory exhaust kit. Instructions are included with the kit. It’s important to make sure the room has enough fresh air. The Dryer must be located where there is no air-flow obstruction. On gas Dryers, adequate clearance as noted on the data plate must be maintained to ensure adequate air for combustion and proper Dryer operation.

THE DRYER MUST NOT BE INSTALLED OR STORED IN AN AREA WHERE IT WILL BE EXPOSED TO WATER AND/OR WEATHER. THE DRYER AREA IS TO BE KEPT CLEAR OF COMBUSTIBLE MATERIALS, GASOLINE, AND OTHER FLAMMABLE VAPORS AND LIQUIDS. A DRYER PRODUCES COMBUSTIBLE LINT. THE AREA AROUND THE DRYER SHOULD BE KEPT LINT-FREE.

ALCOVE OR CLOSET INSTALLATION

The Dryer must be exhausted to the outside to reduce the risk of fire when installed in an alcove or

WARNING closet.

•No other fuel-burning appliance should be installed in the same closet as the Dryer.

•WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED TO THE OUTDOORS. See EXHAUST INFORMATION section.

•Minimum clearances between the Dryer and adjacent walls or other surfaces are: 2” in front, 17” on top, 1” on either side, and 5” in the back.

•The closet front must have two unobstructed air openings for a combined minimum total area of 72 in² with 3” minimum clearance on the top and bottom. A louvered door with equivalent space clearance is acceptable.

10_ installing your dryer

DV220AE-02810A-10_EN.indd Sec11:10

2013-04-23 3:39:49

MOBILE HOME INSTALLATION

The installation of the Dryer in mobile homes must conform to the Manufactured Home Construction and Safety Standard Title 24 CFR, Part 32-80 {formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part 280), 1975} for the United States) or CSA Standards Z240 (for Canada).

When installing a Dryer in a mobile home, provisions for anchoring the Dryer to the floor must be made. Locate an area that has adequate fresh air.

A minimum of 72 in² (465 cm²) of unobstructed space is required.

Call 1-800-SAMSUNG (726-7864) for information on purchasing the Floor Anchoring Kit as an accessory. All mobile home installations must be exhausted to the outside with the exhaust duct termination securely fastened to the mobile home structure, using materials that will not support combustion.

The exhaust duct may not terminate underneath the mobile home. See Exhausting section for more information.

EXHAUSTING

Exhausting the Dryer to the outside will prevent large amounts of lint and moisture from being blown into the room.

In the United States:

•All dryers must be exhausted to the outside.

•The required exhaust duct is 4 inch (102 mm) in diameter.

•Only those foil-type flexible ducts, if any, specifically identified for use with the appliance by the manufacturer and that comply with the Outline for Clothes Dryer Transition Duct, Subject 2158A, shall be used.

•The duct shall not be assembled with screws or other fastening means that extend into the duct and catch lint.

In Canada:

•Only those foil-type flexible ducts, if any, specifically identified for use with the appliance by the manufacturer shall be used.

•All dryers must be exhausted to the outside.

•The exhaust duct should be 4 inch (102 mm) in diameter.

Outside the U.S. and Canada:

•Refer to the local codes.

The dryer must be exhausted to the outside to reduce the risk of fire when installed in an WARNING alcove or closet.

NEVER USE A PLASTIC OR NON-METAL FLEXIBLE DUCT.

If your existing ductwork is plastic, non-metal, or combustible, replace it with metal.

Use only a metal exhaust duct that is non-flammable to ensure containment of exhaust air, heat, and lint.

installing your dryer _11

dryer your installing 01

DV220AE-02810A-10_EN.indd Sec11:11

2013-04-23 3:39:49

installing your dryer

GAS REQUIREMENTS

Use only natural or LP (liquid propane) gases.

THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE UNITED STATES), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA).

Gas dryers are equipped with a burner vent for use with natural gas. If you plan to use your dryer with LP (liquid propane) gas, it must be converted for safe and proper performance by a qualified service technician. A 1/2” (1.27 cm) gas supply line is recommended and must be reduced to connect to the 3/8” (1 cm) gas line on your dryer. The National Fuel Gas Code requires that an accessible, approved manual gas shut-off valve be installed within 6’ of your dryer.

Gas dryers installed in residential garages must be raised 18 inches (46 cm) above the floor.

Additionally, a 1/8” (0.3 cm) N.P.T. (National Pipe Thread) plugged tapping, accessible for test gauge connection, must be installed immediately upstream of your dryer’s gas supply connection.

Your Dryer must be disconnected from the gas supply pipe system during any pressure testing of the system.

DO NOT reuse old flexible metal gas lines. Flexible gas lines must be design certified by the American Gas Association (CGA in Canada).

• Any pipe joint compound used must be resistant to the action of any liquefied petroleum gas.

•As a courtesy, most local gas utilities will inspect a gas appliance installation.

GAS IGNITION – Your Dryer uses an automatic ignition system to ignite the burner. There is no constant burning pilot.

Commonwealth of Massachusetts installation instructions

Your Dryer must be installed by a licensed plumber or gas fitter. A “T” handle manual gas valve must be installed in the gas supply line to your dryer. If a flexible gas connector is used to install your Dryer, the connector must have a maximum length of 3’ (36”).

- Gas leaks may occur in your system, creating a dangerous situation.

WARNING - Gas leaks may not be detected by smell alone.

-Gas suppliers recommend you purchase and install a UL-approved gas detector.

-Install and use in accordance with manufacturer’s instructions.

12_ installing your dryer

DV220AE-02810A-10_EN.indd Sec11:12

2013-04-23 3:39:49

ELECTRICAL REQUIREMENTS

	A Wiring diagram is located on the back of the dryer.
	• Improper connection of the equipment grounding conductor can result in a risk of electric shock.	01
WARNING	Check with a qualified electrician or serviceman if you are in doubt as to whether your Dryer is
	properly grounded. Do not modify the plug provided with your Dryer – if it doesn’t fit the outlet,	installing
	have a proper outlet installed by a qualified electrician.
	• To prevent unnecessary risk of fire, electrical shock, or personal injury, all wiring and grounding
	must be done in accordance with local codes, or in the absence of local codes, with the National	your
	Electrical Code, ANSI/NFPA No. 70-Latest Revision (for the U.S.) or the Canadian Electrical Code
	CSA C22.1 – Latest Revisions and local codes and ordinances. It is your responsibility to provide	dryer
	adequate electrical services for your Dryer.
	• All gas installations must be done in accordance with the national Fuel Code ANSI/Z2231 – Latest
	Revision (for the U.S.) or CAN/CGA – B149 Installation Codes – Latest Revision (for Canada) and
	local codes and ordinances.

GROUNDING

This Dryer must be grounded. In the event of a malfunction or breakdown, the ground will reduce the risk of electrical shock by providing a path of least resistance for the electrical current.

Gas models

WARNING

Your Dryer has a cord with an equipment-grounding conductor and a grounding plug.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided with your Dryer – if it doesn’t fit the outlet, have a proper outlet installed by a qualified electrician.

NEVER CONNECT GROUND WIRE TO PLASTIC PLUMBING LINES, GAS LINES, OR HOT WATER PIPES.

Electric models

WARNING

Your Dryer has a cord with an equipment-grounding conductor and a grounding plug, sold separately.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided with your Dryer – if it doesn’t fit the outlet, have a proper outlet installed by a qualified electrician.

If a power cord is not used and the Electric Dryer is to be permanently wired, the Dryer must be connected to a permanently grounded metal wiring system, or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal.

installing your dryer _13

DV220AE-02810A-10_EN.indd Sec11:13

2013-04-23 3:39:50

installing your dryer

ELECTRICAL CONNECTIONS

Before operating or testing, follow all grounding instructions in the Grounding section.

An individual branch (or separate) circuit serving only your Dryer is recommended. DO NOT USE AN EXTENSION CORD.

Gas models – U.S. and Canada

A 120 volt, 60 Hz AC approved electrical service, with a 15-amp fuse or circuit breaker is required.

Electric models – U.S. only

Most U.S. dryers require a 120/240 volt, 60 Hz AC approved electrical service. Some require 120/208 volt, 60 Hz approved electrical service. The electric service requirements can be found on the data label located behind the door. A 30-amp fuse or circuit breaker on both sides of the line is required.

•If a power cord is used, the cord should be plugged into a 30-amp receptacle.

•The power cord is NOT provided with U.S. electric model dryers.

IMPORTANT:

When local codes allow, the dryer electrical supply may be connected by means of a new power supply cord kit, marked for use with a dryer, that is U.L. listed and rated at a minimum of 120/240 volts, 30-amp with three No. 10 copper wire conductors terminated with closed loop terminals, open-end spade lugs with turned up ends, or with tinned leads.

•Do not reuse a power supply cord from an old Dryer. The power cord electric supply wiring must be retained at the dryer cabinet with a suitable UL-listed strain relief.

•Grounding through the neutral conductor is prohibited for (1) new branch-circuit installations,

(2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor. (Use 4-prong plug for 4 wire receptacle, NEMA type 14-30R.)

Electric models – Canada Only

•A 120/240 volt, 60 Hz AC approved electrical service fused through a 30-amp fuse or circuit breaker on both sides of the line is required.

•All Canadian models are shipped with the power cord attached. The power cord should be plugged into a 30-amp receptacle.

It is not permissible to convert a dryer in Canada to 208 volts.

14_ installing your dryer

DV220AE-02810A-10_EN.indd Sec11:14

2013-04-23 3:39:50

REPLACEMENT PARTS AND ACCESSORIES

If your dryer requires replacement parts or accessories, contact the dealer from whom you purchased your dryer or the SAMSUNG customer care center at 1-800-SAMSUNG(726-7864).

INSTALLATION

Gather the required tools and parts before starting the installation.

Read and follow the instructions provided with any tools listed here.

Tools and Parts

Pliers		Cutting knife		Pipe wrench (gas only)		Nut drivers

dryer your installing 01

Level	Phillips Screwdriver	Duct tape	Wrench

For proper installation, we recommend that you hire a professional. To install:

1.Move your dryer to an appropriate location for installation. Consider installing the dryer and washer side by-side. This will allow access to gas, electrical, and exhaust connections.

Lay two of the carton cushion-tops on the floor. Tip your dryer on its side so it will lay across both cushion-tops.

2.Set your dryer back in an upright position.

3.To ensure that the dryer provides optimal drying performance, it must be level. To minimize vibration, noise, and unwanted movement,the floor must be a perfectly level, solid surface.

	To set the dryer to the same height as the washer, fully retract the	Level
	leveling feet by turning them counterclockwise, then loosen the legs
	by turning them clockwise

Retract fully

Then loosen

Adjust the leveling feet only as much as necessary to level the dryer. Extending the leveling feet more than necessary can cause the dryer to vibrate.

Leveling feet

installing your dryer _15

DV220AE-02810A-10_EN.indd Sec11:15

2013-04-23 3:39:50

installing your dryer

4.Review the Exhausting section before installing the exhaust system. Install the ductwork from your dryer to the exhaust hood. The crimped end of the duct sections must point away from your dryer.

DO NOT use sheet metal screws when assembling ducting. These joints should be taped.

Never use plastic flexible exhaust material.

Tip for tight installations: install a section of exhaust system to your dryer before putting it in place. Use duct tape to secure this section to your dryer, but do not cover ventilation slots at the back of the unit in the dryer cabinet.

5.Review Electrical Requirements section.

BEFORE OPERATING OR TESTING, follow the grounding instructions in the Grounding section.

U.S. MODELS:

IMPORTANT – All U.S. models are produced for a 3-WIRE SYSTEM CONNECTION. The Dryer frame is grounded to the neutral conductor at the terminal block.

A 4-WIRE SYSTEM CONNECTION is required for new or remodeled construction, mobile homes, or if local codes do not permit grounding through neutral conductor. If the 4-wire system is used, the Dryer frame cannot be grounded to the neutral conductor at the terminal block. Refer to the following instructions for 3- and 4-WIRE SYSTEM CONNECTIONS.

Remove the terminal block cover plate.

Insert the power cord with a UL-listed strain relief through the hole provided in the cabinet near the terminal block.

A strain relief must be used.

Do not loosen the nuts already installed on the terminal block. Be sure they are tight. Use a 3/8” (1cm) deep well socket.

6.Review Gas Requirements section. Remove the pipe thread protective cap.

Apply pipe joint compound or about 1 1/2 wraps of Teflon tape over all threaded connections. Pipe joint compound must be resistant to the action of any liquefied petroleum gas.

Connect the gas supply to your Dryer.

An additional fitting is required to connect the 3/4” (1.9 cm) female thread end of a flexible connector to the 3/8” (1 cm) male threaded end on the dryer.

Securely tighten the gas line fitting over threads.

Turn on the gas supply. Check all gas connections for leaks using a soap solution. If bubbles appear, tighten the connections and recheck.

DO NOT use an open flame to check for gas leaks.

16_ installing your dryer

DV220AE-02810A-10_EN.indd Sec11:16

2013-04-23 3:39:50

3-WIRE system connections

1.Loosen or remove the center terminal block screw.

2.Connect the neutral wire (white or center wire) of the power cord to the center, silver-colored terminal screw of the terminal block. Tighten screw.

3.Connect the other wires to outer terminal block screws. Tighten screws.

4.Tighten the strain relief screws.

5.Insert the tab of the terminal block cover into your Dryer’s rear panel slot.

Secure the cover with a hold-down screw. 1. External ground connector

2. Neutral grounding wire (green/yellow)

3. Center silver-colored terminal block screw

4. Neutral wire (white or center wire)

5. 3/4” (1.9 cm) UL-listed strain relief

If converting from a 4-wire electrical system to a 3-wire, the ground strap must be WARNING reconnected to the terminal block support to ground the Dryer frame to the neutral

conductor.

4-WIRE system connections

1.Remove the center terminal block screw.

2.Connect the ground wire (green or unwrapped) of the power cord to the external ground conductor screw.

3.Connect the neutral wire (white or center wire) of the power cord and the appliance ground wire (green with yellow stripes) under the central screw of the terminal block.

4.Connect the other wires to the outer terminal block screws. Tighten screws.

5.Tighten the strain relief screws.

6.Insert the tab of the terminal block cover into your Dryer’s rear panel slot. Secure the cover with a hold-down screw.

1.External ground connector

2.Green or bare copper wire of power cord

3.3/4 in. (1.9 cm) UL-listed strain relief

4.Center silver-colored terminal block screw

5.Grounding wire (green/yellow)

6.Neutral wire (white or center wire)

7.With a level, check your Dryer and make necessary adjustments to the leveling legs.

8.At this time, make sure all gas connections (on gas models), exhaust and electrical connections are complete. Plug in your Dryer, and check operation by using the checklist below.

9.(GAS MODELS ONLY)

The burner may not ignite initially due to air in the gas line. Allowing your Dryer to operate on a heat setting will purge the line. If the gas does not ignite within 5 minutes, turn your Dryer off and wait 5 minutes. Be sure the gas supply to your Dryer has been turned on. In order to confirm gas ignition, check the exhaust for heat.

FINAL INSTALLATION CHECKLIST

Dryer is plugged into an electrical outlet and is properly grounded.

Exhaust ductwork is hooked up and joints are taped.

Plastic flexible duct is NOT used.

Used rigid or stiff-walled flexible metal vent material.

Dryer is leveled and is sitting firmly on the floor.

Gas models – gas is turned on with no gas leaks.

Start your dryer to confirm that it runs, heats, and shuts off.

installing your dryer _17

dryer your installing 01

DV220AE-02810A-10_EN.indd Sec11:17

2013-04-23 3:39:50

installing your dryer

DRYER EXHAUST TIPS

Plastic or non-metal flexible duct presents a potential fire hazard.

WARNING

1.Make sure your dryer is installed properly so it exhausts air easily.

2. Use a 4” diameter rigid metal duct. Tape all joints, including at the dryer.

Never use lint-trapping screws.

3. Keep ducts as straight as possible.

4. Clean all old ducts before installing your new dryer. Be sure the vent flap opens and closes freely. Inspect and clean the exhaust system annually.

Don’t let a poor exhaust system slow drying by:

1.	Restricting your dryer with a poor exhaust system. 1	2
2.	Using a plastic, thin foil, or non-metal flexible duct.
3.	Unnecessarily using long ducts that have many
	elbows.
4.	Having crushed or clogged ducts and vent.
	3	4

18_ installing your dryer

DV220AE-02810A-10_EN.indd Sec11:18

2013-04-23 3:39:50

DOOR REVERSAL

1.	Unplug the power cord.	8.	Reinsert the black screw
2.	Remove two door hinge		in the other hole.
	screws.
3.	Lift the door and remove
	it.
4.	Remove a screw on the	9.	Reinsert the screw (Step
	Frame Front.		4) on the Frame Front.

5. Remove the two screws	10. Place the door on the
on the opposite side of	other side and reattach it
the door hinge.	to the dryer.

6. Remove two screws from	11. Reattach the holder lever.
the holder lever.

7. Remove one black screw	12. Reattach the screws in
from the door hinge.	the remaining holes.

installing your dryer _19

dryer your installing 01

DV220AE-02810A-10_EN.indd Sec11:19

2013-04-23 3:39:51

operating Instructions, tips

To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFTY WARNING INSTRUCTION before operating this appliance.

OVERVIEW OF THE CONTROL PANEL

							3				5	6	7	8
1			2							4					9	10
			To select a cycle, rotate the Cycle Selector dial to the desired cycle.
			The indicator light by the cycle name will illuminate. The Normal, Heavy Duty,
			Perm Press and Delicates cycles are Sensor Dry cycles.
			Sensor Dry automatically senses the moisture in the load and shuts the dryer
			off when the selected dryness level (more dry to damp dry) is reached.
			Normal – Use this cycle to dry loads such as cotton, underwear, and linen.
			Heavy Duty – Use this cycle to get high heat for heavy fabrics such as jeans,
			corduroys, or work clothes.
			Perm Press – Dry wrinkle-free cottons, synthetic fabrics, knits, and
			permanent press fabrics automatically.
1 Cycle Selector			Delicates – The Delicates cycle is designed to dry heat-sensitive items at a

low drying temperature.

Time Dry – Time Dry allows you to select the desired cycle time in minutes. Turn the Cycle Selector dial to Time Dry, then press the Adjust Time up arrow to set the drying time.

Press the arrow repeatedly to scroll through the time settings.

Wrinkle Release – The Wrinkle Release cycle will release wrinkles from items that are clean, dry, and only slightly wrinkled, such as clothes from a crowded closet, suitcase or items that have been in the dryer too long after the cycle has ended. Wrinkle Release can be used with any temperature selection.

Air Fluff – The Air Fluff cycle tumbles the load in room temperature air.

Time can be added or subtracted from the automatically set times in the

Manual Dry cycles (Time Dry, Wrinkle Release, or Air Fluff cycles).

2 Adjust Time	To add or subtract time from the cycle, press the Adjust Time arrow pad up
	or down until the desired time is displayed.
	Wrinkle Prevent provides approximately 90 minutes of intermittent tumbling
	in unheated air at the end of the cycle to reduce wrinkling. Press the Wrinkle
Wrinkle Prevent	Prevent button to activate this feature.
3	The indicator light above the pad will illuminate when Wrinkle Prevent is
Selection Button
	selected. The load is dry, and can be removed at any time during the Wrinkle
	Prevent cycle.

20_ operating Instructions, tips

DV220AE-02810A-10_EN.indd Sec5:20

2013-04-23 3:39:51

			The display window shows the estimated time remaining in the cycle after the
			Start/Pause button is pressed. The estimated time remaining may fluctuate as
			the cycle progresses.
			The Drying light will illuminate and remain lit until the cycle is complete.
			When your dryer is in the cool-down phase, the Cooling light will illuminate.
	4	Digital Graphic	When your dryer is in the wrinkle prevent phase, the Wrinkle Prevent light will
		Display	illuminate.
			When the cycle is complete, “END” appears in the display panel until the
			dryer door is opened, the Power, Close or Start button is pressed or 5
			minutes have passed.
			If your dryer is paused during a cycle, the indicator lights will blink until the
			Start/Pause button is pressed.
			To select the dry level in the Normal, Heavy Duty, or other Sensor Dry cycles,
			press the Dry Level button. An indicator light will illuminate next to the desired
		Dry Level	dryness level. Press the button repeatedly to scroll through the settings.
	5		Larger or bulkier loads may require the More Dry setting for complete
		Selection Button
			dryness. The Less Dry setting is best suited for lightweight fabrics or for
			leaving some moisture in the clothing at the end of the cycle. Use for items
			that lay flat or hang to dry.
			To select the correct temperature for the load, press the Temp button. An
			indicator light will illuminate next to the desired temperature. Press the button
			repeatedly to scroll through the settings.
	6	Temp Selection	High – For sturdy cottons or those labeled Tumble Dry.
		Button	Medium – For permanent press, synthetics, lightweight cottons, or items
			labeled Tumble Dry Medium.
			Low – For heat sensitive items labeled Tumble Dry Low or Tumble Dry Warm.
			Extra Low – Provides the lowest heated dry temperature possible.
			When using Manual Dry cycles, time can be adjusted by pressing the Time
	7	Time Selection	Selection button.
		Button	During the Sensory Dry cycle, the time light indicator is off because exact
			drying times are determined by fluctuating humidity levels.
	8	Start/Pause	Press to pause and restart programs.
		selection button
			Press once to turn your dryer on, press again to turn it off. If your dryer is left
	9	Power button	on for more than 10 minutes without any buttons being touched, the power
			automatically turns off.
			This is an alarm that notifies the user when the average dry level is damp dry
			(80% dried). This is useful when the laundry contains various types of clothing
	10	Mixed load bell	you do not want to dry completely. An alarm sounds for five (5) seconds while
		button	continuing to perform the cycle.

This function can only be selected in the Sensor Dry course, and the dry level can only be selected from among Normal Dry, More Dry.

operating Instructions, tips _21

tips Instructions, operating 02

DV220AE-02810A-10_EN.indd Sec5:21

2013-04-23 3:39:51