Samsung DV365ETBGWR-PKG, DV365ETBGWR, DV365ETBGWRA3 User Manual

DV365*

Gas and Electric Dryer

user manual

This manual is made with 100% recycled paper.

imagine the possibilities

Thank you for purchasing this Samsung product. To receive more complete service or accessory parts, please register your product at or contact

www.samsung.com/register

1-800-SAMSUNG (726-7864)

DV365-03064C_EN.indd 1

2012-06-07 7:54:08

features

1. Extra Large Capacity

Ultra drying capabilities are at your fingertips! Now you can dry extra-large loads. Our ultra large 7.3 cu.ft. capacity dryer circulates more air through your clothes, drying them faster for a wrinkle-free result.

2. Various Drying Cycles & Fuzzy Logic Algorithm

Simply turn the Jog Dial to select one of the 9 automatic drying cycles, including normal and heavy duty, or let the Fuzzy Logic Control measure the degree of dampness and

automatically set the drying time. Precision drying has never been easier than with Samsung.

3. Time Saving

Our cycles are designed with you in mind. All our dryers are designed to dry your clothes in less time... just 42 minutes! Giving you time for more important things in life.

4. Energy Saving

Samsung dryers are super energy efficient. You can dry up to 3.01 pounds of laundry with 1kWh. Also, both the large capacity and Fuzzy Logic Control save energy by automatically drying your clothes the most efficient way.

5. Easy Reversible Door

Our dryers will fit just about anywhere. The direction of our reversible door can be changed easily.

6. Pedestal with Storage Drawers

An optional 15” pedestal is available to raise the dryer for easier loading and unloading. It also offers a built-in storage drawer that can hold a 100 oz. bottle of detergent

7. Stacking (MODEL NO: SK-3A1, SK-4A, SK-5A)

Samsung’s Washers and Dryers can be stacked to maximize usable space.

The Dryer legs need to be removed to stack the Washer and Dryer. An optional stacking kit is available for purchase from your Samsung retailer.

8. Sanitize course

This course allows you to sanitize garments by permeating high temperature heat deep into the fabric during the drying cycle. Use this course to keep your bedding and curtains clean. When selecting this cycle, 99.9% of all bacteria is eliminated through high temperature heat. Use this cycle for clothing, bedding, towels, or other items needing sanitization.

This certification is conducted by NSF International, an independent third-party testing and certification organization.

NSF Protocol P154

Sanitization Performance of

Residential Clothes Dryers

9. 4-way Vent (electric model only : DV365*)

You can install the exhaust vent in the following four (4) positions: back, either side, bottom.

2_ features

DV365-03064C_EN.indd Sec9:2

2012-06-07 7:54:46

safety instructions

Congratulations on your new Samsung Dryer. This manual contains valuable information on the installation, use, and care of your appliance. Please take the time to read this manual to take full advantage of your dryer’s many benefits and features.

WARNING - Risk of Fire

•Clothes dryer installation must be performed by a qualified installer.

•Install the clothes dryer according to the manufacturer’s instructions and local codes.

•Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire.

•To reduce the risk of severe injury or death, follow all installation instructions.

WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS

Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur. It is your responsibility to use common sense, caution, and care when installing, maintaining, or operating your dryer.

Always contact your manufacturer about problems or conditions you do not understand.

IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS

Hazards or unsafe practices that may result in severe personal injury or death.

WARNING

Follow the information in this manual to minimize the risk of fire or explosion or to prevent property damage, personal injury, or death.

Do not store or use gasoline or other flammable vapors and liquids near this or any other appliance.

Hazards or unsafe practices that may result in minor personal injury or

property damage.

CAUTION

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions explicity.

Unplug the power plug from the wall socket.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

SAVE THESE INSTRUCTIONS

safety instructions _3

DV365-03064C_EN.indd Sec1:3

2012-06-07 7:54:46

safety instructions

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your WARNING appliance, follow basic precautions, including the following:

1.Read all instructions before using this appliance.

2.Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode.

3.Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children.

4.Before the appliance is removed from service or discarded, remove the door to the drying compartment.

5.Do not reach into the appliance if the drum is moving.

6.Do not install or store this appliance where it will be exposed to the weather.

7.Do not tamper with controls.

8.Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published userrepair instructions that you understand and have the skills to carry out.

9.Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

10.Clean lint screen before or after each load.

11.Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.

12.Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt.

13.The interior of the appliance and exhaust duct should be cleaned periodically by qualified service personnel.

14.Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

State of California Proposition 65 Warnings:

WARNING

The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances known to the State of California to cause cancer, birth defects, or other reproductive harm, and requires businesses to warn of potential exposure to such substances.

This product contains a chemical known to the State of California to cause cancer, birth defects, or other reproductive harm. This appliance can cause low-level exposure to some of the substances listed, including benzene, formaldehyde, and carbon monoxide.

Gas appliances may cause low-level exposure to some of the substances listed including benzene, formaldehyde, carbon monoxide, and soot; as a result of possible incomplete combustion of natural gas or LP fuels. Exposure to these substances can be minimized further by properly venting the dryer to the outdoors.

SAVE THESE INSTRUCTIONS

4_ safety instructions

DV365-03064C_EN.indd Sec1:4

2012-06-07 7:54:46

WHAT TO DO IF YOU SMELL GAS:

•Do not try to light any appliance.

•Do not turn on the appliance.

•Do not touch any electrical switch.

•Do not use any phone in your building.

•Clear the room, building or area of all occupants.

•Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

•If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

Read all instructions before using the appliance.

To reduce the risk of fire or explosion:

WARNING

•Do not dry items that have been previously cleaned, washed, soaked, or spotted with gasoline, dry cleaning solvents, or other flammable or explosive substances. They emit vapors that could ignite or explode. Any material that has been in contact with a cleaning solvent or flammable liquids or solids should not be placed in the dryer until all traces of these flammable liquids or solids and their fumes have been removed.

There are many highly flammable items used in homes, such as acetone, denatured alcohol, gasoline, kerosene, some liquid household cleaners, some spot removers, turpentine, waxes, and wax removers

•Items containing foam rubber (may be labeled latex foam) or similarly textured rubberlike materials must not be dried on a heat setting. Heated foam rubber materials can, under certain circumstances, produce fire by spontaneous combustion.

Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is necessary when the appliance is used near children and pets.

Before discarding or removing your dryer from service, remove the door to the drying compartment to prevent children or animals from becoming trapped inside.

Do not reach into the appliance when the drum is moving.

Do not install or store this appliance where it will be exposed to the weather.

Do not tamper with the controls.

Do not repair, replace, or attempt to service any part of the appliance unless specifi cally instructed to in the user-repair instructions and only if you have the understanding and skills to carry out the repair, replacement, or service procedure.

Do not use fabric softeners or products to eliminate static unless the softener or product is recommended for use in dryers.

Clean the lint screen before or after each load.

Keep the area around the exhaust opening and surrounding areas free from lint, dust, and dirt.

The interior of the dryer and exhaust duct should be cleaned periodically by qualified service personnel.

SAVE THESE INSTRUCTIONS

safety instructions _5

DV365-03064C_EN.indd Sec1:5

2012-06-07 7:54:46

safety instructions

This appliance must be properly grounded. Never plug the power cord into a receptacle that is not grounded adequately and in accordance with local and national codes. See the installation instructions for information about grounding this appliance.

Do not sit on top of the dryer.

Because of continuing product improvements, Samsung reserves the right to change specifications without notice. For complete details, see the Installation Instructions packed with your product before selecting cabinetry, making cutouts, or beginning installation.

Ensure pockets are free from small, irregularly shaped, hard objects, foreign material, etc. WARNING ie. coins, knives, pins, etc. These objects could damage your dryer.

Do not wash clothing with large buckles, buttons, or other heavy metal or solid objects.

Gas leaks may occur in your system, resulting in a dangerous situation.

WARNING

Gas leaks may not be detected by smell alone.

Gas suppliers recommend you purchase and install a UL-approved gas detector.

Install and use in accordance with the manufacturer’s instructions.

Do not place items in your dryer that have been spotted or soaked with vegetable oil or cooking oil. Even after being washed, these items may contain significant amounts of these oils.

Residual oil on clothing can ignite spontaneously. The potential for spontaneous combustion increases when items containing vegetable oil or cooking oil are exposed to heat. Heat sources such as your dryer can warm these items, allowing an oxidation reaction in the oil to occur. Oxidation creates heat. If this heat cannot escape, the items can become hot enough to catch fire. Piling, stacking, or storing these kinds of items may prevent heat from escaping and can create a fire hazard.

All washed and unwashed fabrics that contain vegetable oil or cooking oil can be dangerous. Washing these items in hot water with extra detergent will reduce, but not eliminate, the hazard. Always use the Cool Down cycle for these items to reduce their temperature. Never remove these items from the dryer hot or interrupt the drying cycle until the items have run through the Cool Down cycle. Never pile or stack these items when they are hot.

SAVE THESE INSTRUCTIONS

6_ safety instructions

DV365-03064C_EN.indd Sec1:6

2012-06-07 7:54:46

contents

INSTALLING YOUR DRYER

8

OPERATING INSTRUCTIONS, TIPS

22

CARE AND CLEANING

27

SPECIAL LAUNDRY TIPS

28

TROUBLESHOOTING

29

APPENDIX

31

8Unpacking your dryer

8The Dryer’s Exterior

8Key installation requirements

9Tools needed for installation

9Replacement parts and accessories

10Ducting requirements

12Important to installer

12Location considerations

12Alcove or closet installation

13Mobile home installation

13Exhausting

14Gas requirements

15Electrical requirements

15Grounding

16Electrical connections

17Installation - General procedure

19Final installation checklist

20Dryer Exhaust Tips

21Door Reversal

22 Overview of the control panel

24Child lock

24Sound Off

25Drying Rack (Optional Part)

26Clean the lint filter

26Load the dryer properly

26Getting started

27Control Panel

27 Tumbler

27Powder coated tumbler

27Dryer Exterior

27Dryer Exhaust System

28Special laundry tips

29Check these pointers if your dryer…

30Information codes

31Fabric care chart

32Protecting the environment

32Declaration of conformity

32Specifications

33Cycle chart

contents _7

DV365-03064C_EN.indd Sec3:7

2012-06-07 7:54:46

installing your dryer

UNPACKING YOUR DRYER

Unpack your Dryer and inspect it for shipping damage. If your Dryer was damaged during shipping, contact 1-800-SAMSUNG (726-7864).To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the dryer.

Packing materials can be dangerous to children. Keep all packing material (plastic bags, polystyrene, WARNING etc.) well out of children’s reach.

THE DRYER’S EXTERIOR

Control panel

Door

Adjustable legs

A Drying Rack is not supplied with this model. The Drying Rack is optional. You can purchase it through a service center.

KEY INSTALLATION REQUIREMENTS

Hire a professional to install this dryer properly. If a service call has to be made as a result of poor setup, adjustment, or connection, it is considered the responsibility of the installer. If you install the dryer, you are responsible.

Make sure you have everything necessary for proper installation:

•A GROUNDED ELECTRICAL OUTLET. See Electrical Requirements. See page 15

•A POWER CORD for electric dryers (except Canada). See page 16.

•GAS LINES (if you are installing a gas dryer) must meet national and local codes.

•EXHAUST SYSTEM – must be rigid metal or flexible stiff-walled metal exhaust ducting. See the ducting and exhaust requirements on pages 10 - 11 and 13 and the dryer exhaust tips on page 20..

8_ installing your dryer

DV365-03064C_EN.indd Sec11:8

2012-06-07 7:54:46

TOOLS NEEDED FOR INSTALLATION

Gather the required tools and parts before starting the installation.

Read and follow the instructions provided with any tools listed here.

Tools and Parts

Pliers		Cutting knife		Pipe wrench (gas only)		Nut drivers

Level	Phillips Screwdriver	Duct tape	Wrench

REPLACEMENT PARTS AND ACCESSORIES

If your dryer requires replacement parts or accessories, contact the dealer from whom you purchased your dryer or the SAMSUNG customer care center at 1-800-SAMSUNG (726-7864).

installing your dryer _9

dryer your installing 01

DV365-03064C_EN.indd Sec11:9

2012-06-07 7:54:46

installing your dryer

DUCTING REQUIREMENTS

•Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct.

•Do not use a smaller duct.

•Ducts larger than 4 inches (10.2 cm) in diameter can cause increased lint accumulation. Lint accumulation should be cleaned regularly.

•If a flexible metal duct must be used, use the type with a stiff sheet metal wall. Do not use a flexible duct with a thin foil wall. Serious blockage can result if the flexible metal duct is bent too sharply.

•Never install any type of flexible duct in walls, ceilings, or other concealed spaces.

•Only a rigid or flexible metal duct should be used for exhausting.

•Keep the exhaust duct as straight and short as possible.

•Secure joints with duct tape. Do not use screws.

•DO NOT EXHAUST DRYER INTO ANY WALL, CEILING, CRAWL SPACE, OR CONCEALED SPACE OF A BUILDING, GAS VENT, OR ANY OTHER COMMON DUCT OR CHIMNEY. THIS COULD CREATE A FIRE HAZARD FROM LINT EXPELLED BY THE DRYER.

•A plastic flexible duct can kink, sag, be punctured, reduce airflow, extend drying times, and affect dryer operation.

•Exhaust systems longer than recommended can extend drying times, affect machine operation, and may collect lint.

•The exhaust duct should end with an exhaust hood that has a swing-out damper to prevent back drafts and the entry of wildlife. Never use an exhaust hood with a magnetic damper.

•The hood should have at least 12 inches (30.5 cm) of clearance between the bottom of the hood and the ground or other obstruction. The hood opening should point down.

•Never install a screen over the exhaust outlet.

•To avoid lint buildup, do not exhaust the dryer directly into a window well. Do not exhaust under a house or porch.

•If exhaust ductwork must run through an unheated area, the duct should be insulated and slope slightly down towards the exhaust hood to reduce condensation and lint buildup.

•Inspect and clean the interior of the exhaust system at least once a year. Unplug the power cord before cleaning.

•Check frequently to be sure the exhaust hood damper opens and closes freely.

•Check once per month, and clean at least one time per year. Note: If clothes are not getting dry, then check ducting for obstructions.

ELECTRIC AND GAS DRYER

Weather Hood Type

Recommended

Use only for short-run installation

	4” (10.16 cm)		2.5” (6.35 cm)
No. of 90° elbows	Rigid	Metallic Flexible*	Rigid	Metallic Flexible*
0	24.4 m (80 ft.)	12.4 m (41 ft.)	22.6 m (74 ft.)	10.1 m (33 ft.)
1	20.7 m (68 ft.)	11.2 m (37 ft.)	18.9 m (62 ft.)	8.8 m (29 ft.)
2	17.4 m (57 ft.)	10.1 m (33 ft.)	15.5 m (51 ft.)	7.6 m (25 ft.)
3	14.3 m (47 ft.)	9.0 m (29 ft.)	12.5 m (41 ft.)	6.5 m (21 ft.)

*Do not use non-metallic flexible duct.

10_ installing your dryer

DV365-03064C_EN.indd Sec11:10

2012-06-07 7:54:47

If the new Dryer is being installed into an existing exhaust system, you must make sure:

•The exhaust system meets all local, state, and national codes.

•That a flexible plastic duct is not used.

•To Inspect and clean all lint buildup from inside the existing duct.

•The duct is not kinked or crushed.

•The exhaust hood damper opens and closes freely.

The static pressure in any exhaust system must not exceed 0.83 inches of water column or be less than 0.

This can be measured while the Dryer is running with a manometer at the point where the exhaust duct connects to the Dryer. A no-heat setting should be used. The Dryer tumbler should be empty and the lint filter clean.

installing your dryer _11

dryer your installing 01

DV365-03064C_EN.indd Sec11:11

2012-06-07 7:54:47

installing your dryer

IMPORTANT TO INSTALLER

Please read the following instructions carefully before installing the dryer. These instructions should be kept for future reference.

REMOVE THE DOOR FROM ALL DISCARDED APPLIANCES TO AVOID THE DANGER OF A CHILD WARNING SUFFOCATING.

LOCATION CONSIDERATIONS

Locate the Dryer where there is enough space at the front for loading and enough space behind for the exhaust system. This Dryer is factory-ready for rear exhaust. To exhaust out the bottom or the left, use the accessory exhaust kit. Instructions are included with the kit. It’s important to make sure the room has enough fresh air. The Dryer must be located where there is no air-flow obstruction.

For gas Dryers, you must provide the clearance noted on the data plate to ensure adequate air for combustion and proper Dryer operation.

DO NOT INSTALL OR STORE THE DRYER IN AN AREA WHERE IT WILL BE EXPOSED TO WATER AND/ OR WEATHER. KEEP THE DRYER AREA CLEAR OF COMBUSTIBLE MATERIALS, GASOLINE, AND OTHER FLAMMABLE VAPORS AND LIQUIDS. A DRYER PRODUCES COMBUSTIBLE LINT. THE AREA AROUND THE DRYER SHOULD BE KEPT LINT-FREE.

ALCOVE OR CLOSET INSTALLATION

You must exhaust the dryer to the outside to reduce the risk of fire when installed in an alcove or

WARNING closet.

•No other fuel-burning appliance should be installed in the same closet as the Dryer.

•WARNING: To reduce the risk of fire, YOU MUST EXHAUST THIS DRYER TO THE OUTDOORS. See the EXHAUST INFORMATION section.

•Minimum clearances between the Dryer and adjacent walls or other surfaces are: 2” in front, 17” on top, 1” on either side, and 5” in the back.

•The closet front must have two unobstructed air openings for a combined minimum total area of 72 in² with 3” minimum clearance on the top and bottom. A louvered door with equivalent space clearance is acceptable.

12_ installing your dryer

DV365-03064C_EN.indd Sec11:12

2012-06-07 7:54:47

MOBILE HOME INSTALLATION

The installation of the Dryer in mobile homes must conform to the Manufactured Home Construction and Safety Standard Title 24 CFR, Part 32-80 {formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part 280), 1975} for the United States) or CSA Standards Z240 (for Canada).

When installing a Dryer in a mobile home, you must make provisions for anchoring the dryer to the floor. Locate the dryer in an area that has adequate fresh air.

A minimum of 72 in² (465 cm²) of unobstructed space is required.

Call 1-800-SAMSUNG (726-7864) for information about purchasing the Floor Anchoring Kit as an accessory. All mobile home installations must be exhausted to the outside with the exhaust duct termination securely fastened to the mobile home structure, using materials that will not support combustion.

The exhaust duct may not terminate underneath the mobile home. See Exhausting section for more information.

EXHAUSTING

Exhausting the Dryer to the outside will prevent large amounts of lint and moisture from being blown into the room.

In the United States:

•All dryers must be exhausted to the outside.

•The required exhaust duct is 4 inches (102 mm) in diameter.

•Use only those foil-type flexible ducts, if any, specifically identified for use with the appliance by the manufacturer and that comply with the Outline for Clothes Dryer Transition Duct, Subject 2158A.

•Do not assemble the duct with screws or other fasteners that extend into the duct and can catch lint.

In Canada:

•Use only those foil-type flexible ducts, if any, specifically identified for use with the appliance by the manufacturer.

•All dryers must be exhausted to the outside.

•The exhaust duct should be 4 inches (102 mm) in diameter.

Outside the U.S. and Canada:

•Refer to the local codes.

You must exhaust the dryer to the outside to reduce the risk of fi re when you install the WARNING dryer in an alcove or closet.

NEVER USE A PLASTIC OR NON-METAL FLEXIBLE DUCT.

If your existing ductwork is plastic, non-metal, or combustible, replace it with metal.

Use only a metal exhaust duct that is non-flammable to ensure containment of exhaust air, heat, and lint.

installing your dryer _13

dryer your installing 01

DV365-03064C_EN.indd Sec11:13

2012-06-07 7:54:47

installing your dryer

GAS REQUIREMENTS

Use only natural or LP (liquid propane) gases.

THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE UNITED STATES), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA).

Gas dryers are equipped with a burner vent for use with natural gas. If you plan to use your dryer with LP (liquid propane) gas, it must be converted for safe and proper performance by a qualified service technician. A 1/2” (1.27 cm) gas supply line is recommended and must be reduced to connect to the 3/8” (1 cm) gas line on your dryer. The National Fuel Gas Code requires that an accessible, approved manual gas shut-off valve be installed within 6’ of your dryer.

Gas dryers installed in residential garages must be raised 18 inches (46 cm) above the floor.

Additionally, a 1/8” (0.3 cm) N.P.T. (National Pipe Thread) plugged tapping, accessible for test gauge connection, must be installed immediately upstream of your dryer’s gas supply connection.

Your Dryer must be disconnected from the gas supply pipe system during any pressure testing of the system.

DO NOT reuse old flexible metal gas lines. Flexible gas lines must be design certified by the American Gas Association (CGA in Canada).

• Any pipe joint compound used must be resistant to the action of any liquefied petroleum gas.

•As a courtesy, most local gas utilities will inspect a gas appliance installation.

GAS IGNITION – Your Dryer uses an automatic ignition system to ignite the burner. There is no constant burning pilot.

Commonwealth of Massachusetts installation instructions

Your Dryer must be installed by a licensed plumber or gas fitter. A “T” handle manual gas valve must be installed in the gas supply line to your dryer. If a flexible gas connector is used to install your Dryer, the connector can be no longer than 3’ (36”).

- Gas leaks may occur in your system, creating a dangerous situation.

WARNING - Gas leaks may not be detected by smell alone.

-Gas suppliers recommend you purchase and install a UL-approved gas detector.

-Install and use in accordance with manufacturer’s instructions.

14_ installing your dryer

DV365-03064C_EN.indd Sec11:14

2012-06-07 7:54:47

ELECTRICAL REQUIREMENTS

A Wiring diagram is located on the back of the dryer.

•Improper connection of the equipment grounding conductor can result in a risk of electric shock.

WARNING Check with a qualified electrician or serviceman if you are in doubt as to whether your Dryer is properly grounded. Do not modify the plug provided with your Dryer – if it doesn’t fit the outlet, have a proper outlet installed by a qualified electrician.

•To prevent unnecessary risk of fire, electrical shock, or personal injury, all wiring and grounding must be done in accordance with local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA No. 70-Latest Revision (for the U.S.) or the Canadian Electrical Code CSA C22.1 – Latest Revisions and local codes and ordinances. It is your responsibility to provide adequate electrical services for your Dryer.

•All gas installations must be done in accordance with the national Fuel Code ANSI/Z2231 – Latest Revision (for the U.S.) or CAN/CGA – B149 Installation Codes – Latest Revision (for Canada) and local codes and ordinances.

GROUNDING

This Dryer must be grounded. In the event of a malfunction or breakdown, the ground will reduce the risk of electrical shock by providing a path of least resistance for the electrical current.

Gas models

WARNING

Your Dryer has a cord with an equipment-grounding conductor and a grounding plug.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided with your Dryer – if it doesn’t fit the outlet, have a proper outlet installed by a qualified electrician.

NEVER CONNECT THE GROUND WIRE TO PLASTIC PLUMBING LINES, GAS LINES, OR HOT WATER PIPES.

Electric models

WARNING

Your Dryer requires a cord with an equipment-grounding conductor and a grounding plug which is sold separately.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided with your Dryer – if it doesn’t fit the outlet, have a proper outlet installed by a qualified electrician.

If a power cord is not used and the Electric Dryer is to be permanently wired, the Dryer must be connected to a permanently grounded metal wiring system, or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal.

installing your dryer _15

dryer your installing 01

DV365-03064C_EN.indd Sec11:15

2012-06-07 7:54:47

installing your dryer

ELECTRICAL CONNECTIONS

Before operating or testing, follow all grounding instructions in the Grounding section.

An individual branch (or separate) circuit serving only your Dryer is recommended. DO NOT USE AN EXTENSION CORD.

Gas models – U.S. and Canada

A 120 volt, 60 Hz AC approved electrical service, with a 15-amp fuse or circuit breaker is required.

Electric models – U.S. only

Most U.S. dryers require a 120/240 volt, 60 Hz AC approved electrical service. Some require 120/208 volt, 60 Hz approved electrical service. The electric service requirements can be found on the data label located behind the door. A 30-amp fuse or circuit breaker on both sides of the line is required.

•If a power cord is used, the cord should be plugged into a 30-amp receptacle.

•The power cord is NOT provided with U.S. electric model dryers.

IMPORTANT:

When local codes allow, you can connect the dryer’s electrical supply with a new power supply cord kit, marked for use with a dryer, that is U.L. listed and rated at a minimum of 120/240 volts, 30-amp with three No. 10 copper wire conductors terminated with closed loop terminals, openend spade lugs with turned up ends, or with tinned leads.

•Do not reuse a power supply cord from an old Dryer. The power cord electric supply wiring must be retained at the dryer cabinet with a suitable UL-listed strain relief.

•Grounding through the neutral conductor is prohibited for (1) new branch-circuit installations,

(2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor. (Use 4-prong plug for 4 wire receptacle, NEMA type 14-30R.)

Electric models – Canada Only

•A 120/240 volt, 60 Hz AC approved electrical service fused through a 30-amp fuse or circuit breaker on both sides of the line is required.

•All Canadian models are shipped with the power cord attached. The power cord should be plugged into a 30-amp receptacle.

You may not convert a dryer in Canada to 208 volts.

16_ installing your dryer

DV365-03064C_EN.indd Sec11:16

2012-06-07 7:54:47

Installation - General procedure

For proper installation, we recommend that you hire a qualified installer.

Read these instructions completely before you begin the installation.

To install the dryer, follow these steps:

1.Move your dryer to an appropriate location for installation. Consider installing the dryer and washer side- by-side so you have easy access to both appliances.

To move the dryer easily, lay two of the carton cushion-tops on the floor. Tip your dryer on its side so it lies across both cushion-tops. Push the dryer so that it is near its final location. Set your dryer upright. Leave enough room around the dryer so you can attach the duct work, power cord, etc.

2.If you need to change the direction of the door, go to Door Reversal on page . When done, return to Step 3 below.

3.Review the Exhausting section before installing the exhaust system. Install the duct work from your dryer to the exhaust hood. The crimped end of the duct sections must point away from your dryer. DO NOT use sheet metal screws when assembling ducting. These joints should be taped. Never use plastic flexible exhaust material.

A tip for tight installations: Attach a section of the exhaust system to your dryer before putting it in place. Use duct tape to secure this section to your dryer, but do not cover the ventilation slots at the back of the dryer cabinet.

4.If you have an electric model, skip to Step 6. If you have a gas model, go to the next step.

5.Review the Gas Requirements section, then follow the lettered steps below.

a.Remove the pipe thread protective cap.

b.Apply pipe joint compound or about 1 1/2 wraps of Teflon tape over all threaded connections.

The pipe joint compound must be resistant to the action of any liquefied petroleum gas.

c.Connect the gas supply to your dryer. An additional fitting is required to connect the 3/4” (1.9 cm) female thread end of a flexible connector to the 3/8” (1 cm) male threaded end on the dryer.

d.Securely tighten the gas line fitting over the threads.

e.Turn on the gas supply. Check all gas connections for leaks using a soap solution. If bubbles appear, tighten the connections and recheck. DO NOT use an open flame to check for gas leaks.

f.Go to Step 6 on the next page

installing your dryer _17

dryer your installing 01

DV365-03064C_EN.indd Sec11:17

2012-06-07 7:54:47

installing your dryer

6.Review the Electrical Requirements section, then follow the 3 Wire system connection instructions (Step 7) or 4 Wire system instructions (Step 8) below.

7.Three Wire system instructions:

a.Loosen or remove the center terminal block screw.

b.Connect the neutral wire (white or center wire) of the power cord to the center, silver-colored terminal screw of the terminal block. Tighten screw.

c.Connect the other wires to outer terminal block screws. Tighten screws.

d.Tighten the strain relief screws.

e.Insert the tab of the terminal block cover into your dryer’s rear panel slot.

f.Secure the cover with a hold-down screw.

g.BEFORE OPERATING OR TESTING, follow the grounding instructions in the Grounding section.

If converting from a 4-wire electrical system to a 3-wire, WARNING you must connect the ground strap to the terminal block

support to ground the dryer frame to the neutral conductor.

We recommend using Ring terminals. If you use Strap terminals, please ensure you install them perfectly.

8.Four Wire System instructions:

a.Remove the center terminal block screw.

b.Connect the ground wire (green or unwrapped) of the power cord to the external ground conductor screw.

c.Connect the neutral wire (white or center wire) of the power cord and the appliance ground wire (green with yellow stripes) under the central screw of the terminal block.

d.Connect the other wires to the outer terminal block screws. Tighten screws.

e.Tighten the strain relief screws.

f.Insert the tab of the terminal block cover into your dryer’s rear panel slot.

g.Secure the cover with a hold-down screw.

h.BEFORE OPERATING OR TESTING, follow the grounding instructions in the Grounding section.

We recommend using Ring terminals. If you use Strap terminals, please ensure you install them perfectly.

18_ installing your dryer

Three Wire System

B W R

1.External ground connector

2.Neutral grounding wire (green/yellow) from dryer wiring harness

3.Center silver-colored terminal block screw

4.Neutral wire (white or center wire) from power cord.

5.3/4” (1.9 cm) UL listed strain relief

B - Black, W - White, R - Red

Four Wire System

G

B W R

1.External ground connector

2.Green or bare copper wire from power cord

3.3/4 in. (1.9 cm) UL listed strain relief

4.Center silver-colored terminal block screw

5.Grounding wire (green/yellow) from dryer wiring harness

6.Neutral wire (white or center wire) from power cord

B - Black, W - White, R - Red, G - Green

DV365-03064C_EN.indd Sec11:18

2012-06-07 7:54:47

U.S. MODELS:

IMPORTANT – All U.S. models are designed for a 3-WIRE SYSTEM CONNECTION. The dryer frame is grounded to the neutral conductor at the terminal block. A 4-WIRE SYSTEM CONNECTION is required for new or remodeled construction, mobile homes, or if local codes do not permit grounding through neutral. If you use the 4-wire system, you cannot ground the dryer frame to the neutral conductor at the terminal block.

Refer to the following instructions for 3- and 4-WIRE SYSTEM CONNECTIONS:

Remove the terminal block cover plate. Insert the power cord with a UL-listed strain relief through the hole provided in the cabinet near the terminal block.

A strain relief must be used. Do not loosen the nuts already installed on the terminal block. Be sure they are tight. Use a 3/8” (1 cm) deep well socket.

9. To ensure that the dryer provides optimal drying performance, it must
be level. To level the dryer, follow the lettered steps below:		Level
a. Using a level, check if the dryer is level side to side and then front
to back.
b. If the dryer is not level, adjust the leveling feet on the bottom of
the dryer until the washer is level side to side and back to front.
Turning the feet clockwise retracts the feet. Turning the feet
clockwise loosens and extends them.
To set the dryer to the same height as the washer, fully
retract the leveling feet by turning them counterclockwise,
then loosen the feet by turning them clockwise. Once
the dryer is the same height as the washer, follow the
directions above to level the dryer.
		Leveling feet
Retract fully	Then loosen

Adjust the leveling feet only as much as necessary to level the dryer. Extending the leveling feet more than necessary can cause the dryer to vibrate.

10.Make sure all gas connections (on gas models), exhaust, and electrical connections are complete. Plug in your dryer, and then check its operation by using the checklist below.

11.For GAS MODELS ONLY - DV231AE*:

The burner may not ignite initially due to air in the gas line. Allowing your dryer to operate on a heat setting will purge the line. If the gas does not ignite within 5 minutes, turn your dryer off and wait 5 minutes. Be sure the gas supply to your dryer has been turned on. To confirm gas ignition, check the exhaust for heat.

FINAL INSTALLATION CHECKLIST

The dryer is plugged into an electrical outlet and is properly grounded.

The exhaust ductwork is hooked up and joints are taped.

You have used rigid or stiff-walled flexible metal duct material, not plastic flexible duct.

The dryer is leveled and is sitting firmly on the fl oor.

For gas models: The gas is turned on and there are no gas leaks.

Start your dryer to confirm that it runs, heats, and shuts off.

dryer your installing 01

installing your dryer _19

DV365-03064C_EN.indd Sec11:19

2012-06-07 7:54:47

installing your dryer

DRYER EXHAUST TIPS

Plastic or non-metal flexible duct presents a potential fire hazard.

WARNING

1.Make sure your dryer is installed properly so it exhausts air easily.

2. Use a 4” diameter rigid metal duct. Tape all joints, including at the dryer.

Never use lint-trapping screws.

3. Keep ducts as straight as possible.

4. Clean all old ducts before installing your new dryer. Be sure the vent flap opens and closes freely. Inspect and clean the exhaust system annually.

Don’t let a poor exhaust system slow drying by:

1.	Restricting your dryer with a poor exhaust system. 1	2
2.	Using a plastic, thin foil, or non-metal flexible duct.
3.	Using unnecessarily long ducts that have many
	elbows.
4.	Using crushed or clogged vent or ducts.
	3	4

20_ installing your dryer

DV365-03064C_EN.indd Sec11:20

2012-06-07 7:54:48

DOOR REVERSAL

1.	Unplug the power cord.	8.	Reinsert the black screw
2.	Remove two door hinge		in the other hole.
	screws.
3.	Lift the door and remove
	it.
4.	Remove a screw on the	9.	Reinsert the screw (Step
	Frame Front.		4) on the Frame Front.

5. Remove the two screws	10. Place the door on the
on the opposite side of	other side and reattach it
the door hinge.	to the dryer.

6. Remove two screws from	11. Reattach the holder lever.
the holder lever.

7. Remove one black screw	12. Reattach the screws in
from the door hinge.	the remaining holes.

installing your dryer _21

dryer your installing 01

DV365-03064C_EN.indd Sec11:21

2012-06-07 7:54:48

operating Instructions, tips

OVERVIEW OF THE CONTROL PANEL

6

			To select a cycle, rotate the Cycle Selector dial to the desired cycle.
			The indicator light by the cycle name will illuminate. The Normal, Heavy Duty, Perm
			Press and Delicates cycles are Sensor Dry cycles. Sensor Dry automatically senses the
			moisture in the load and shuts the dryer off when the load reaches the dryness level
			((more dry to damp dry) you selected.
			Normal – Use this cycle to dry loads of cotton, underwear, and linen.
			Heavy Duty – Use this cycle to dry heavy fabrics such as jeans, corduroys, or work
			clothes with high temperature heat.
			Perm Press – Dry wrinkle-free cottons, synthetic fabrics, knits, and permanent press
			fabrics automatically.
			Delicates – The Delicates cycle is designed to dry heat-sensitive items at a low drying
			temperature.
	1 Cycle Selector		Sanitize - Lets you sanitize garments by infusing high temperature heat deep into the
			fabric during the drying cycle. Use this cycle to keep your bedding and curtains clean
			through sanitization.
			Time Dry – Time Dry allows you to select the desired cycle time in minutes. Turn the
			Cycle Selector dial to Time Dry, and then press the Time Key arrow to set the drying
			time.
			Press the arrow repeatedly to scroll through the time settings.
			Quick Dry – Provides a 30 minute drying cycle.
			Refresh – This cycle is best for smoothing out wrinkles and reducing odors from loads
			consisting of one to four dry items. In this cycle a small amount of water is sprayed into
			the dryer drum after several minutes of tumbling with heat.
			Wrinkle Away – The Wrinkle Away cycle removes wrinkles from clothes stored in
			closets, etc. It provides a wrinkle release via optimized steam care. You can change the
			drying time.(Minimum time : 20 minutes) *For best results, load no more than 3 items.
			The display window shows the estimated time remaining in the cycle after you have
			pressed the Start/Pause button. The estimated time remaining may fluctuate as the
			cycle progresses.
			The Drying light will illuminate and remain lit until the cycle is complete. When your dryer is
	2	Digital Graphic	in the cool-down phase, the Cooling light will illuminate. When your dryer is in the wrinkle
		Display	prevent phase, the Wrinkle Prevent light will illuminate.

When the cycle is complete, “END” appears in the display panel until you open the dryer door, press the Power, Close, or Start button, or 5 minutes have passed.

If your dryer is paused during a cycle, the indicator lights will blink until the Start/Pause button is pressed.

22_ operating Instructions, tips

DV365-03064C_EN.indd Sec5:22

2012-06-07 7:54:48

			Wrinkle Prevent provides approximately 180 minutes of intermittent tumbling in
		Wrinkle Prevent	unheated air at the end of the cycle to reduce wrinkling. Press the Wrinkle Prevent
	3		button to activate this feature.
		Selection Button
			The indicator light above the pad will illuminate when you select Wrinkle Prevent.
			The load is dry and you can remove it at any time during the Wrinkle Prevent cycle.
			To select the dry level in the Normal, Heavy Duty, or other Sensor Dry cycles, press the
		Dry Level	Dry Level button. An indicator light will illuminate next to the desired dryness level. Press
	4		the button repeatedly to scroll through the settings. Larger or bulkier loads may require
		Selection Button
			the Very Dry or More Dry setting for complete dryness. Damp Dry is designed to partially
			dry items. Use for items that lay flat or hang to dry.
			To select the correct temperature for a load, press the Temp button. An indicator light
			will illuminate next to the desired temperature. Press the button repeatedly to scroll
			through the settings.
	5	Temp Selection	High – For sturdy cottons or those labeled Tumble Dry.
			Medium – For permanent press, synthetics, lightweight cottons, or items labeled
		Button
			Tumble Dry Medium.
			Low – For heat sensitive items labeled Tumble Dry Low or Tumble Dry Warm.
			Extra Low – Provides the lowest heated dry temperature possible.
			When using Manual Dry cycles, you can adjust the time by pressing the Time Selection
	6	Time Selection	button.
		Button	During the Sensory Dry cycle, the time light indicator is off because exact drying times
			are determined by fluctuating humidity levels.
			You can add time to the automatically set times in the Manual Dry cycles (Time Dry,
			Quick Dry).
			If you press and hold the Adjust Time button, the time slowly increases until it reaches
			the maximum time setting. When you set the time to the maximum, and you briefly
	7	Adjust Time	press the button, the time returns to the lowest time setting.
			After selecting a preset time using the Time button, you can adjust the time using
			the Adjust Time button.
			For example, press the Time button to select 40 minutes, and then press the
			Adjust Time button to add 5 minutes.
	8	Start/Pause	Press to pause and restart programs.
		selection button
	9	Power button	Press once to turn your dryer on. Press again to turn it off. If you turn your dryer on and
			do not touch any buttons for 10 minutes, the power automatically turns off.

operating Instructions, tips _23

tips Instructions, operating 02

DV365-03064C_EN.indd Sec5:23

2012-06-07 7:54:48

operating Instructions, tips

CHILD LOCK

Child Lock prevents children from playing with your dryer.

Turning On and Off

To turn Child Lock on or off, press the Temp. and Time buttons simultaneously for 3 seconds.

Child Lock Details:

-You can set Child Lock while your dryer is running.

-Once you turn Child Lock on, no button, except for the Power button, will respond until you release the Child Lock function.

-The Child Lock indicator will be lit.

If you do not turn Child Lock off before you turn your dryer off, Child Lock will still be on when you turn your dryer on again. To turn Child Lock off, follow the instructions above.

When other buttons, except for the Power button, do not respond, check the Child Lock indicator. If Child Lock is on, follow the instructions above to turn Child Lock off.

SOUND OFF

Use this function to mute the button and operating sounds.

Setting and Releasing

To turn the Sound Off function on or off, press the Dry Level and Temp. buttons simultaneously for 3 seconds.

Sound Off Details:

-You can set Sound Off while your dryer is running.

-Once you have activated Sound Off, the button and operating sounds are muted until you deactivate it.

-The Sound Off indicator will be lit.

If you do not turn the Sound Off function off before you turn your dryer off, It will still be on when you turn your dryer on again. To turn Sound Off off, follow the instructions above.

24_ operating Instructions, tips

DV365-03064C_EN.indd Sec5:24

2012-06-07 7:54:48

DRYING RACK (OPTIONAL PART)

Installing and using the drying rack

1.Open the Dryer door.

2.Position the drying rack in the tumbler, placing the front lip of the drying rack on top of the lint filter.

3.Place the rear legs in the two recessed areas of the dryer’s back wall, and then push down the middle of the drying rack to fix.

4.Place the items to be dried on the rack, leaving space between them so air can circulate.

5.Close the Dryer door.

6.Use the Time Dry cycle. Select the time according to the moisture and weight of the items. Start the Dryer. It may be necessary to reset the timer if a longer drying time is needed.

SUGGESTED ITEMS	SUGGESTED TEMP. SETTINGS
Washable sweaters	Extra Low
(block to shape and lay flat on rack)
Stuffed toys	Extra Low
(cotton or polyester fiberfilled)

Drying foam rubber, plastic, or rubber on a heat setting may cause damage to the item and WARNING create a fire hazard.

Drying Rack is not supplied in this model. The Drying Rack is optional. You can purchase it through a service center. (Part code : DC61-01522A)

operating Instructions, tips _25

tips Instructions, operating 02

DV365-03064C_EN.indd Sec5:25

2012-06-07 7:54:48

operating Instructions, tips

CLEAN THE LINT FILTER

•After each load.

•To shorten drying time.

•To operate more energy efficiently.

Do not operate your dryer without the lint filter in place.

LOAD THE DRYER PROPERLY

•Place only one washload in your dryer at a time.

•In mixed loads, heavy and lightweight fabrics will dry differently. This may result in lightweight fabrics being dry while heavy fabrics remain damp at the end of a drying cycle.

•Add one or more additional similar items to your dryer when you are drying only one or two items. This improves the tumbling action and drying efficiency.

•Overloading restricts tumbling action, resulting in uneven drying as well as excessive wrinkling of some fabrics.

GETTING STARTED

1.Load your dryer loosely – DO NOT overload.

2.Close the door.

3.Select the appropriate cycle and options for the load (Refer to the “Cycle Chart” section on page 33).

4.Press the Start/Pause button.

5.The dryer indicator light will illuminate.

6.The estimated cycle time will appear in the display.

The time may fluctuate as humidity levels fluctuate in the dryer.

• When the cycle is complete, “End” will appear in the display.

•Pressing Power cancels the cycle and stops your dryer.

•The Drying, Cooling, and Done indicator lights will illuminate during those portions of the cycle.

Do not place anything on top of your dryer while it is running.

WARNING

26_ operating Instructions, tips

DV365-03064C_EN.indd Sec5:26

2012-06-07 7:54:49

care and cleaning

CONTROL PANEL

Clean with a soft, damp cloth. Do not use abrasive substances. Do not spray cleaners directly on the panel.

The control panel finish may be damaged by some laundry pre-treatment soil and stain remover products. Apply such products away from your Dryer and wipe up any spills or overspray immediately.

TUMBLER

Remove any stains such as crayon, ink, or fabric dye (from new items such as towels or jeans) with an allpurpose cleaner.

Tumble old towels or rags to remove any excess stain or cleaning substance.

Once these steps are followed, stains may still be visible, but should not transfer to subsequent loads.

POWDER COATED TUMBLER

To clean the powder coated tumbler, use a damp cloth with a mild, non-abrasive cleaner suitable for powder coated surfaces.

Remove the cleaner residue and dry with a clean cloth.

DRYER EXTERIOR

The entire dryer has a high-gloss finish. Clean with a soft, damp cloth. Do not use abrasive substances. Protect the surface from sharp objects as they may scratch or damage the finish. Do not place any heavy or sharp objects or a detergent box on the dryer. Keep them on the purchased pedestal or in a separate storage box.

DRYER EXHAUST SYSTEM

Inspect and clean the dryer exhaust system yearly to maintain optimum performance. The outside exhaust hood should be cleaned more frequently to ensure proper operation.

care and cleaning _27

cleaning and care 03

DV365-03064C_EN.indd Sec4:27

2012-06-07 7:54:49

special laundry tips

SPECIAL LAUNDRY TIPS

Please follow the care label or manufacturer’s instructions for drying special items. If care label instructions are not available, use the following information as a guide.

Bedspreads & Comforters	• Follow the care label instructions or dry using the Normal cycle with
	the temperature set to High.
	• Make sure the item is thoroughly dry before using or storing.
	• May require repositioning to ensure even drying.
Blankets	• Use the Normal cycle and dry only one blanket at a time for best
	tumbling action.
	• Make sure the blanket is thoroughly dry before using or storing.
Curtains & Draperies	• Use the Perm Press cycle and the Low or Extra Low temperature
	setting o help minimize wrinkling.
	• Dry in small loads for best results and remove as soon as possible.
Cloth Diapers	• Use the Normal cycle and the High temperature setting for soft,
	fluffy diapers.
Down–filled Items (jackets,	• Use the Normal cycle and the Low or Extra Low temperature setting.
sleeping bags, comforters,	• Adding a couple of dry towels shortens drying time and absorbs
etc.)	moisture.
Pillows	• Use the Normal cycle.
	• Add a couple of dry towels to help the tumbling action and to fluff the
	item.
	• DO NOT dry kapok or foam pillows in the dryer.
Plastics (shower curtains,	• Use the Time Dry cycle and the Low or Extra Low temperature
outdoor furniture covers,	settings depending on the care label instructions.
etc.)

THINGS TO AVOID :

•Fiberglass items (curtains, draperies, etc.).

•Woolens, unless recommended on the label.

•Vegetable or cooking oil-soaked items.

•Foam Rubber (rug backs, stuffed toys, shoulder pads, etc.)

28_ special laundry tips

DV365-03064C_EN.indd Sec6:28

2012-06-07 7:54:49

troubleshooting

CHECK THESE POINTERS IF YOUR DRYER…

PROBLEM	SOLUTION
Doesn’t run.	• Be sure the door is latched shut.
	• Be sure the power cord is plugged into a live electrical outlet.
	• Check your home’s circuit breakers or fuses.
	• Press the Start/Pause button again if the door is opened during the cycle.
Doesn’t heat.	• Check your home’s circuit breakers or fuses.
	• On a gas dryer, see if the gas supply is on.
	• Clean the lint filter and exhaust duct.
	• See if the Dryer has moved into the cool-down phase of the cycle.
Doesn’t dry.	• Check all of the above, plus...
	• Be sure the exhaust hood outside your home can open and close freely.
	• Check exhaust system for lint buildup. Ducting should be inspected
	and cleaned annually.
	• Use a 4” rigid metal exhaust duct.
	• Do not overload. 1 wash load = 1 dryer load.
	• Sort heavy items from lightweight items.
	• Large, bulky items like blankets or comforters may require
	repositioning to ensure even drying.
	• Check that the washer is draining properly to extract adequate water
	from the load.
	• The load may be too small to tumble properly. Add a few towels.
Is noisy.	• Check the load for objects such as coins, loose buttons, nails, etc.
	Remove promptly.
	• It is normal to hear the dryer gas valve or heating element cycle on
	and off during the drying cycle.
	• Be sure the Dryer is leveled properly as outlined in the installation
	instruction.
	• It is normal for the Dryer to hum due to the high volume of air moving
	through the dryer drum and exhaust system.
Dries unevenly.	• Seams, pockets, and other similarly heavy areas may not be
	completely dry when the rest of the load has reached the selected
	dryness level. This is normal. Select the More Dry setting if desired.
	• If one heavy item is dried with a lightweight load, such as one towel
	with sheets, it is possible that the heavy item will not be completely
	dry when the rest of the load has reached the selected dryness level.
	Sort heavy items from lightweight items for best drying results.
Has an odor.	• Household odors from paint, varnish, strong cleaners, etc. may enter
	the dryer with the surrounding room air. This is normal as the Dryer
	draws the air from the room, heats it, pulls it through the tumbler, and
	exhausts it outside.
	• When these odors linger in the air, ventilate the room completely
	before using the Dryer.

Shuts off before load is dry • The dryer load is too small. Add more items or a few towels and restart the cycle.

•The dryer load is too large. Remove some items and restart the dryer.

troubleshooting _29

troubleshooting 05

DV365-03064C_EN.indd Sec7:29

2012-06-07 7:54:49

troubleshooting

Lint on clothes	• Make sure the lint filter is cleaned before every load. With some loads
	that produce high amounts of lint, it may be necessary to clean the
	filter during the cycle.
	• Some fabrics are lint producers (for example, a fuzzy white cotton
	towel) and they should be dried separately from clothes that are lint
	trappers(for example, a pair of black linen pants).
	• Divide larger loads into smaller loads for drying.
	• Check pockets thoroughly before washing and drying clothes.
Garments still wrinkled after	• Small loads of 1 to 4 items work best.
Wrinkle-Away	• Load fewer garments.
	• Load similar-type garments.
Odors remain in clothing	• Fabrics having strong odors should be washed in a normal cycle.
after Refresh.
Water drips from the nozzle	• This is steam condensation. The dripping water will stop after a short
when Steam-Care starts	time.
Sprayed water is not visible	• Sprayed water is difficult to see when the door is closed.
during Steam-Care

INFORMATION CODES

Information codes may be displayed to help you better understand what is occurring with your Dryer.

	ERROR DISPLAY	MEANING	SOLUTION
	tS	Clogged Lint Screen	Clean the screen or vent.
		Vent is restricted	If the problem continues call for service.
	tO
	dO	Running the dryer with door open	Close the door and then restart.
	dE		If the problem continues call for service.
	dF	Door is not closing properly	Call for service.
	bE	Unit detects a button is being	Make sure a button is NOT being pressed
	bE2	pressed for over 30secs or button is	continuously. Try restarting the cycle.
		stuck	If the problem continues call for service.
	od	Invalid Dry time	Call for service.
	hE	Invalid heating Temp	Call for service.
	Et	EEPROM is not communicating	Try restarting the cycle.
		properly	If the problem continues call for service.
	FE	Invalid power source Frequency	Try restarting the cycle.
			If the problem continues call for service.

For any codes not listed above, call 1–800–726–7864 (1–800–SAMSUNG)

30_ troubleshooting

DV365-03064C_EN.indd Sec7:30

2012-06-07 7:54:49