Samsung DC48E-M, DC48E-H, DC55E-M, DC40E-M, DC32E-M User Manual

Reverse Side

Quick Setup Guide

DC32E-M DC40E-M DC48E-M DC55E-M

DC40E-H DC48E-H

−−The colour and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance.

−−Download the user manual from the website for further details. http://www.samsung.com/displaysolutions

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

BN68-07848H-00

Checking the Components

Contact the vendor where you purchased the product if any components are missing.

The pictures may look different from the actual components.

	Quick Setup Guide	Warranty card	MagicInfo Software
		(Not available in some locations)	DVD

	Power cord	Batteries	Remote Control
		(Not available in some locations)

RS232C(IN) adapter AV/Component adapter

AUDIO adapter

Control Panel

Speaker

DC32E-M

Speaker

1Power on the product.

If you press the button when the product is turned on, the control menu will be displayed.

-To exit the OSD menu, press and hold the panel key for at least one second.

2Move to the upper or lower menu. You can also adjust the value of an option.

3Move to the left or right menu.

-You can adjust the volume by moving the panel key left or right when the control menu is not displayed.

4Remote sensor

Press a button on the remote control pointing at the sensor on the front of the product to perform the corresponding function.

5Spacer logo (Optional)

Do not pull on the spacer logo using force. The logo may tear or break off.

DCE-M_DCE-H_India_QSG_BN68-07848H-00.indd 1

1Connects to the audio of a source device.

2Connects to a source device using the AV/Component adapter.

3Receives sound from a PC via an audio cable.

4Connect to a USB memory device.

5DVI IN: Connects to a source device using a DVI cable or HDMI-DVI cable.

MAGICINFO IN: Use the (dedicated) DP-DVI cable when connecting a network box (sold separately).

6Connects to a source device using an HDMI cable.

7Supplies power to the external sensor board or receives the light sensor signal.

8Connects to MDC using an RS232C adapter.

9Connects to a source device using a D-SUB cable.

0 Connects to MDC using a LAN cable.

Troubleshooting Guide

	Issues	Solutions
	The screen keeps	Check the cable connection between
	switching on and off.	the product and PC, and ensure the
		connection is secure.
	No Signal is displayed	Check that the product is connected
	on the screen.	correctly with a cable.
		Check that the device connected to the
		product is powered on.
	Not Optimum Mode is	This message is displayed when a signal
	displayed.	from the graphics card exceeds the product’s
		maximum resolution and frequency.
		Refer to the Standard Signal Mode Table
		and set the maximum resolution and
		frequency according to the product
		specifications.
	The images on the	Check the cable connection to the
	screen look distorted.	product.
	The screen is not clear.	Adjust Coarse and Fine.
	The screen is blurry.
		Remove any accessories (video extension
		cable, etc) and try again.
		Set the resolution and frequency to the
		recommended level.
	The screen appears	Check that the resolution and frequency
	unstable and shaky.	of the PC and graphics card are set within
		a range compatible with the product.
	There are shadows or
		Then, change the screen settings if
	ghost images left on
		required by referring to the Additional
	the screen.
		Information on the product menu and the
		Standard Signal Mode Table.

Issues	Solutions
The screen is too bright.	Adjust Brightness and Contrast.
The screen is too dark.
Screen colour is	Go to Picture and adjust the Colour Space
inconsistent.	settings.
White does not really	Go to Picture and adjust the White Balance
look white.	settings.
There is no sound.	Check the connection of the audio cable or
	adjust the volume.
	Check the volume.
The volume is too low.	Adjust the volume.
	If the volume is still low after turning
	it up to the maximum level, adjust the
	volume on your PC sound card or software
	programme.
The remote control	Make sure that the batteries are correctly
does not work.	in place (+/-).
	Check if the batteries are flat.
	Check for power failure.
	Make sure that the power cord is
	connected.
	Check for any special lighting or neon
	signs switched on in the vicinity.

2016-03-11 1:26:48