PRODUCT SPECIFICATION |
transmission and power |
|
|
EC-3000C/U Series EthernetConnect™ Extender
1, 4, 8, OR 16 PORTS WITH TRUE POE TO 30 WATTS, LOCAL OR REMOTE
Product Features
•Transmits Individual Ethernet Data Channels with Power over Ethernet Plus (PoE+) Power Injection and Pass-Through PoE+ over Standard Cat5/Cat5e/Cat6 UTP Cable or Coaxial Cable
•Extends Ethernet up to 914 m (3,000 ft) at 10 Mbps or
610 m (2,000 ft) at 100 Mbps over Cat5/Cat5e/Cat6 UTP Cable
•Extends Ethernet up to 1,524 m (5,000 ft) at 10 Mbps or 549 m (1,800 ft) at 100 Mbps over Coaxial Cable
•Extended Temperature Operation from –40° to 75°C (–40° to 167°F)
•Extended Pass-Through PoE Meets the IEEE802.3at Standard for Power over Ethernet
•Full 10/100 Mbps Bandwidth
•Supports Multicast, Unicast, and Jumbo Frame
•Symmetric Bandwidth Provides Consistent Upload and Download with Virtually Zero Packet Loss over the Total Usable Distance
•Type Tested to RFC-2544 TCP/IP Network Bandwidth Packet Transmission Standards
•User-Selectable Data Rate for Maximum Bandwidth and Transmission Distance Utilization
•Complies with all Major IEEE Standards and RFC Network Protocols for UDP, TCP/IP, HTTP/HTTPs
The EC-3000C Series is ideally suited for applications where the existing coaxial cable needs to be leveraged for transmission of IP signals. For UTP applications, the EC-3000U Series is an effective Cat5/Cat5e/Cat6 UTP extender device beyond the 100 m (328 feet) limit of traditional Ethernet. In addition, for system configurations that have a single cable connected to the camera, the EC-3000C/U Series can become a true PoE device and source PoE to the powered device. This eliminates the need for midspans or PoE-enabled Ethernet switches to provide a fully 802.3at compatible application. Designed to be a cost-effective, advanced-use product, the EC-3000C/U Series provides maximum flexibility in these applications without any programming.
•Tested and Certified by an Independent Laboratory for Full Compliance with the Environmental Requirements (Ambient Operating Temperature, Mechanical Shock, Vibration, Humidity with Condensation, High-Line/Low-Line Voltage Conditions, and Transient Voltage Protection) of NEMA TS-1/TS-2 and the Caltrans Specification for Traffic Signal Control Equipment
•LED Status Indicators Confirm Operating Status
•Available in Small Unit Size, Interchangeable Stand Alone, or 1 RU Rack Mounted-Models
•Designed and Manufactured in the USA
The EthernetConnect™ EC-3000C/U Series is used to extend Ethernet over copper (EoC). The EC-3000C Series extends up to 16 channels of 10/100 Mbps Ethernet with PoE+ power injection and pass-through PoE+ over coaxial cable. The EC-3000U Series extends up to 16 channels of 10/100 Mbps Ethernet with PoE+ power injection and pass-through PoE+ over twisted pair cable (Cat5/ Cat5e/6 UTP). With the ability to connect directly to a PoE+ switch or the ability to generate PoE+ power with a 48 V input to either the local or remote ends, these units provide the ultimate flexibility for extending a powered device (PD) over long distance copper.
A complete set includes both a local and a remote module. Remote modules are small unit size in either a oneor four-channel configuration. Local modules are also available in the small unit size in oneor four-channel configuration as well as available in a 1 RU rack size for larger channel counts. All application configurations should be verified at the time of ordering to facilitate ease of installation.
International Standards
Organization Registered Firm;
ISO 9001 Quality System
C3977 / NEW 3-10-14
TECHNICAL SPECIFICATIONS
TYPICAL APPLICATIONS
Note: Coaxial applications use EC-3000C modules; UTP applications use EC-3000U modules.
PoE PASS-THROUGH MODE
REMOTE PoE INJECTION MODE
LOCAL PoE INJECTION MODE
MULTICHANNEL PoE APPLICATION
IMPORTANT NOTE. PLEASE READ. The network implementations are shown as general representations only and are not intended to show detailed network topologies. Your actual network will differ, requiring changes or perhaps additional network equipment to accommodate the systems as illustrated. Please contact your local Pelco representative to discuss your specific requirements.