HT-R340
Table of contents
Loading...
E
n
5.1ch Home Theater System
HT-SR600
AV Receiver (HT-R340)
Front Speakers (SKF-350F L/R)
Center Speaker (SKC-350C)
Surround Speakers (SKM-350S L/R)
Subwoofer (SKW-350)
Instruction Manual
Thank you for purchasing an Onkyo 5.1ch Home
Theater System. Please read this manual thoroughly
before making connections and plugging in the unit.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new 5.1ch Home Theater Sys-
tem.
Please retain this manual for future reference.
Contents
Introduction ..................................... 2
Connection .................................... 19
Turning On & First Time Setup..... 34
Basic Operation
Playing your AV components....... 36
Using the Tuner............................ 38
Enjoying the Listening Modes ..... 46
Advanced Operation..................... 48
Troubleshooting ............................ 55
Specifications................................ 58
2
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radia-
tors, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are pro-
vided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience recepta-
cles, and the point where they exit from the appara-
tus.
11. Only use attachments/accessories specified by the
manufacturer.
12.
Use only with the cart, stand,
tripod, bracket, or table spec-
ified by the manufacturer, or
sold with the apparatus.
When a cart is used, use cau-
tion when moving the cart/
apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
15. Damage Requiring Service
Unplug the apparatus from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
A. When the power-supply cord or plug is damaged,
B. If liquid has been spilled, or objects have fallen
into the apparatus,
C. If the apparatus has been exposed to rain or
water,
D. If the apparatus does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the apparatus to its normal operation,
E. If the apparatus has been dropped or damaged in
any way, and
F. When the apparatus exhibits a distinct change in
performance this indicates a need for service.
16. Object and Liquid Entry
Never push objects of any kind into the apparatus
through openings as they may touch dangerous volt-
age points or short-out parts that could result in a
fire or electric shock.
The apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases shall be placed on the apparatus.
Don’t put candles or other burning objects on top of
this unit.
17. Batteries
Always consider the environmental issues and fol-
low local regulations when disposing of batteries.
18. If you install the apparatus in a built-in installation,
such as a bookcase or rack, ensure that there is ade-
quate ventilation.
Leave 20 cm (8") of free space at the top and sides
and 10 cm (4") at the rear. The rear edge of the shelf
or board above the apparatus shall be set 10 cm (4")
away from the rear panel or wall, creating a flue-like
gap for warm air to escape.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS
TO RAIN OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS
OUVRIR
AVIS
PORTABLE CART WARNING
S3125A
3
Precautions
1. Recording Copyright
—Unless it’s for personal use
only, recording copyrighted material is illegal with-
out the permission of the copyright holder.
2. AC Fuse
—The AC fuse inside the unit is not user-
serviceable. If you cannot turn on the unit, contact
your Onkyo dealer.
3. Care
—Occasionally you should dust the unit all
over with a soft cloth. For stubborn stains, use a soft
cloth dampened with a weak solution of mild deter-
gent and water. Dry the unit immediately afterwards
with a clean cloth. Don’t use abrasive cloths, thin-
ners, alcohol, or other chemical solvents, because
they may damage the finish or remove the panel let-
tering.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SEC-
TION CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear panel
(e.g., AC 230–240 V, 50 Hz or AC 120 V, 60 Hz).
Some models have a voltage selector switch for
compatibility with power systems around the world.
Before you plug in such a model, make sure that the
voltage selector is set to the correct voltage for your
area.
Pressing the [STANDBY/ON] button to select
Standby mode does not fully shutdown the unit. If
you do not intend to use the unit for an extended
period, remove the power cord from the AC outlet.
5. Never Touch this Unit with Wet Hands
—Never
handle this unit or its power cord while your hands
are wet or damp. If water or any other liquid gets
inside this unit, have it checked by your Onkyo
dealer.
6. Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you origi-
nally bought it.
• Do not leave rubber or plastic items on this unit
for a long time, because they may leave marks on
the case.
• This unit’s top and rear panels may get warm
after prolonged use. This is normal.
• If you do not use this unit for a long time, it may
not work properly the next time you turn it on, so
be sure to use it occasionally.
For U.S. models
FCC Information for User
CAUTION:
The user changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interfer-
ence in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interfer-
ence to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV tech-
nician for help.
For Canadian Models
NOTE:
THIS CLASS B DIGITAL APPARATUS
COMPLIES WITH CANADIAN ICES-003.
For models having a power cord with a polarized plug:
CAUTION:
TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
Modèle pour les Canadien
REMARQUE:
CET APPAREIL NUMÉRIQUE DE
LA CLASSE B EST CONFORME À LA NORME
NMB-003 DU CANADA.
Sur les modèles dont la fiche est polarisée:
ATTENTION:
POUR ÉVITER LES CHOCS ÉLEC-
TRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE CORRE-
SPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
4
Precautions
—Continued
For British models
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by
qualified service personnel.
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured mark-
ings identifying the terminals in your plug, proceed as
follows:
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or
coloured red.
IMPORTANT
The plug is fitted with an appropriate fuse. If the fuse
needs to be replaced, the replacement fuse must
approved by ASTA or BSI to BS1362 and have the same
ampere rating as that indicated on the plug. Check for
the ASTA mark or the BSI mark on the body of the fuse.
If the power cord’s plug is not suitable for your socket
outlets, cut it off and fit a suitable plug. Fit a suitable
fuse in the plug.
For European Models
Memory Backup
The AV receiver uses a battery-less memory backup
system in order to retain radio presets and other settings
when it’s unplugged or in the case of a power failure.
Although no batteries are required, the AV receiver
must be plugged into an AC outlet in order to charge the
backup system. Once it has been charged, the AV
receiver will retain the settings for several weeks,
although this depends on the environment and will be
shorter in humid climates.
Speaker Precautions
Placement
• The subwoofer cabinet is made out of wood and is
therefore sensitive to extreme temperatures and
humidity, do not put it in locations subject to direct
sunlight or in humid places, such as near an air condi-
tioner, humidifier, bathroom, or kitchen.
• Do not put water or other liquids close to the speakers.
If liquid is spilled over the speakers, the drive units
may be damaged.
• Speakers should only be placed on sturdy, flat surfaces
that are free from vibration. Putting them on uneven or
unstable surfaces, where they may fall and cause dam-
age, will affect the sound quality.
• Subwoofer is designed to be used in the upright verti-
cal position only. Do not use it in the horizontal or
tilted position.
• If the unit is used near a turntable, CD player or DVD
player, howling or slipping of sound may occur. To
prevent this, move the unit away from the turntable,
CD player or DVD player, otherwise lower the unit’s
output level.
Using Close to a TV or Computer
TVs and computer monitors are magnetically sensitive
devices and as such are likely to suffer discoloration or
picture distortion when conventional speakers are
placed nearby. To prevent this, the SKF-350F and
SKC-350C feature internal magnetic shielding. In some
situations, however, discoloration may still be an issue,
in which case you should turn off your TV or monitor,
wait 15 to 30 minutes, and then turn it back on again.
This normally activates the degaussing function, which
neutralizes the magnetic field, thereby removing any
discoloration effects. If discoloration problems persist,
try moving the speakers away from your TV or monitor.
Note that discoloration can also be caused by a magnet
or demagnetizing tool that’s too close to your TV or
monitor.
Do not place SKM-350S close to TV or a computer
monitor because they have no magnetic shield.
Input Signal Warning
The speakers can handle the specified input power when
used for normal music reproduction. If any of the fol-
lowing signals are fed to them, even if the input power is
within the specified rating, excessive current may flow
in the speaker coils, causing burning or wire breakage:
1. Interstation noise from an untuned FM radio.
2. Sound from fast-forwarding a cassette tape.
3. High-pitched sounds generated by an oscillator,
electronic musical instrument, and so on.
4. Amplifier oscillation.
5. Special test tones from audio test CDs and so on.
6. Thumps and clicks caused by connecting or discon-
necting audio cables (Always turn off your amplifier
before connecting or disconnecting cables.)
7. Microphone feedback.
Declaration of Conformity
We,
ONKYO EUROPE
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
GROEBENZELL, GERMANY
ONKYO EUROPE ELECTRONICS GmbH
K. MIYAGI
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
corresponding technical standards such as EN60065,
EN55013, EN55020 and EN61000-3-2, -3-3.
5
Features
HT-R340 AV Receiver
• 100 W/channel into 6 ohms (FTC)
• 100 W/channel into 6 ohms (DIN)
• 120 W/channel into 6 ohms (JEITA)
• Dolby
*1
Digital and Dolby Pro Logic II
• DTS and DTS Neo:6
*2
5.1
• Optimum Gain Volume Circuitry
• Massive High Current Power Supply (H.C.P.S.) trans-
former
• CinemaFILTER
• Non-Scaling Configuration
• A-Form — Auto Format Sensing
• OR-EQ (OptiResponse Equalizer)
*3
function
• 192 kHz/24-bit D/A converters
•Powerful and highly accurate Analog Devices 32-bit
DSP processing
•3 digital inputs (2 optical, 1 coaxial)
• HDTV-ready component video switching (3 inputs, 1
output)
• Adjustable crossover (40/50/60/80/100/120/150/
200 Hz)
• Speaker A/B terminal
• Color-coded speaker terminal posts
• system control
HTP-350 Speaker Package
SKF-350F L/R 2-Way Front Speakers
• 3-1/4" (8 cm) cone woofer
• 3/4" (2 cm) ceramic tweeter
• Magnetically shielded
• Color-coded speaker terminals and speaker cable
• 6-ohm impedance
SKC-350C 2-Way Center Speaker
• 3-1/4" (8 cm) cone woofer
• 3/4" (2 cm) ceramic tweeter
• Magnetically shielded
• Color-coded speaker terminals and speaker cable
• 6-ohm impedance
SKM-350S L/R Surround Speakers
• 3-1/4" (8 cm) cone full-range speaker
• 6-ohm impedance
• Color-coded speaker terminals and speaker cable
SKW-350 Bass Reflex Subwoofer
• 8" (20 cm) cone woofer
• Color-coded speaker terminals and speaker cable
Contents
Important Safety Instructions.................2
Precautions ..............................................3
Speaker Precautions ...............................4
Features....................................................5
Package Contents ...................................6
Before Using the AV receiver................... 7
Front & Rear Panels ................................ 8
Speaker Package...................................11
Remote Controller ................................. 12
Enjoying Home Theater ........................19
Connecting Your Speakers...................20
Connecting Antenna .............................22
Connecting Your Components .............. 24
Turning On ............................................. 34
First Time Setup ....................................35
Playing Your AV Components..............36
Using the Tuner ..................................... 38
Common Functions...............................42
Recording............................................... 45
Using the Listening Modes...................46
Adjusting the Listening Modes ............ 48
Advanced Setup ....................................50
If you can’t resolve an issue, try resetting the AV
receiver by holding down the [VIDEO 1] button
and pressing the [STANDBY/ON] button.
*1. Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are regis-
tered trademarks of Dolby Laboratories.
*2. “DTS” and “Neo:6” are trademarks of Digital Theater Sys-
tems, Inc.
*3. OptiResponse, and OR-EQ are trademarks of Onkyo Cor-
poration.
Introduction
Connection
Turning On & First Time Setup
Basic Operation
Enjoying the Listening Modes
Advanced Operation
Troubleshooting .................................... 55
Specifications........................................ 58
6
Package Contents
Make sure you have the following items:
* In catalogs and on packaging, the letter at the end of the
product name indicates the color. Specifications and oper-
ation are the same regardless of color.
HT-R340
HT-R340
Remote controller & two batteries (AA/R6)
Indoor FM antenna
(Connector type varies from country to country.)
AM loop antenna
Power-plug adapter
Only supplied in certain countries. Use this adapter if
your AC outlet does not match with the plug on the AV
receiver’s power cord. (Adapter varies from country to
country.)
(American type shown)
HTP-350
Speaker cable for front speakers and center speaker
11 ft. (3.5 m)
Speaker cables for surround speakers 30 ft. (9 m)
Speaker cables for subwoofer 15 ft. (4.5 m)
16 thin rubber stoppers, 12 thick rubber stoppers
Front speakers
(SKF-350F L/R)
Center speaker
(SKC-350C)
Surround speakers
(SKM-350S)
Subwoofer (SKW-350)
(Red) (White) (Green)
(Blue) (Gray)
(Purple)
7
Before Using the AV receiver
Some models have a voltage selector switch for compat-
ibility with power systems around the world. Before you
plug in this model, make sure that the voltage selector is
set to the correct voltage for your area. If it isn’t, use a
small screwdriver to set it as appropriate. For example, if
the voltage in your area is 120 volts, set the selector to
“120V.” If it’s between 220 and 240 volts, set it to “220-
240V.”
Notes:
• If the remote controller doesn’t work reliably, try
replacing the batteries.
• Don’t mix new and old batteries or different types of
batteries.
• If you intend not to use the remote controller for a long
time, remove the batteries to prevent damage from
leakage or corrosion.
• Expired batteries should be removed as soon as possi-
ble to prevent damage from leakage or corrosion.
To use the remote controller, point it at the AV receiver’s
remote control sensor, as shown below.
Notes:
• The remote controller may not work reliably if the AV
receiver is subjected to bright light, such as direct sun-
light or inverter-type fluorescent lights. Keep this in
mind when installing.
• If another remote controller of the same type is used in
the same room, or the AV receiver is installed close to
equipment that uses infrared rays, the remote control-
ler may not work reliably.
• Don’t put anything, such as a book, on the remote con-
troller, because the buttons may be pressed inadvert-
ently, thereby draining the batteries.
• The remote controller may not work reliably if the AV
receiver is installed in a rack behind colored glass
doors. Keep this in mind when installing.
• The remote controller will not work if there’s an obsta-
cle between it and the AV receiver’s remote control
sensor.
Setting the Voltage Selector
(on some models)
Installing the Batteries
1
To open the battery compartment, press
the small hollow and slide open the cover.
2
Insert the two supplied batteries (AA/R6)
in accordance with the polarity diagram
inside the battery compartment.
3
Slide the cover shut.
Using the Remote Controller
Approx. 16 ft.
(5 m)
Remote control sensor
STANDBY indicator
AV receiver
8
Front & Rear Panels
For detailed information, see the pages in parentheses.
A
STANDBY/ON button (34)
This button is used to set the AV receiver to On or
Standby.
B
STANDBY indicator (34)
This indicator lights up when the AV receiver is in
Standby mode, and it flashes while a signal is being
received from the remote controller.
C
Remote-control sensor (7)
This sensor receives control signals from the remote
controller.
D
STEREO button (46)
This button is used to select the Stereo listening
mode.
E
LISTENING MODE [ ]/[ ] buttons (46)
These buttons are used to select the listening modes.
F
Display
See “Display” on page 9.
G
DISPLAY button (37)
This button is used to display various information
about the currently selected input source.
H
DIGITAL INPUT button (35, 54)
This button is used to assign the digital inputs and to
specify the format of digital input signals.
I
DIMMER or RT/PTY/TP button (41, 42)
This button is used to adjust the display brightness.
On the European model, this is the RT/PTY/TP but-
ton, and it’s used with RDS (Radio Data System).
See “Using RDS (European models only)” on
page 40.
Front Panel
TONE
+
STEREO
LISTENING MODE
DISPLAY
DIGITAL INPUT
DIMMER MEMORY
TUNING MODE
RETURN
TUNING / PRESET
ENTER
SETUP
STANDBY
STANDBY/ON
CLEAR
PHONES
MULTl CH DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER CD
MASTER VOLUME
A SPEAKERS B
1
QN O P R S
2
3 4 5 7 8 9 J K L M6
TONE
+
STEREO
LISTENING MODE
DISPLAY
DIGITAL INPUT
RT/PTY/TP MEMORY
TUNING MODE
RETURN
TUNING / PRESET
ENTER
SETUP
STANDBY
STANDBY/ON
CLEAR
PHONES
MULTl CH DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER CD
MASTER VOLUME
A SPEAKERS B
9
North American and Asian Models
European Models
9
Front & Rear Panels
—Continued
J
MEMORY button (39)
This button is used when storing or deleting radio
presets.
K
TUNING MODE button (38)
This button is used to select the Auto or Manual tun-
ing mode.
L
Arrow/TUNING/PRESET & ENTER buttons
(48, 50–53)
When the AM or FM input source is selected, the
TUNING [ ] [ ] buttons are used to tune the
tuner, and the PRESET [ ] [ ] buttons are used
to select radio presets (see pages 38, 39). When the
setup menus are used, they work as arrow buttons
and are used to select and set items. The ENTER
button is also used with the setup menus.
M
MASTER VOLUME control (36)
This control is used to adjust the volume of the AV
receiver.
N
PHONES jack (42)
This 1/4-inch phone jack is for connecting a stan-
dard pair of stereo headphones for private listening.
O
SPEAKERS A & B buttons (36)
These buttons are used to turn speaker sets A and B
on or off.
P
TONE, [–] & [+] buttons (42)
These buttons are used to adjust the bass and treble.
Q
Input selector buttons (35–37)
These buttons are used to select from the following
input sources: MULTI CH, DVD, VIDEO 1/VCR,
VIDEO 2, VIDEO 3, TAPE, TUNER, or CD.
The [MULTI CH] button selects the DVD analog
multichannel input.
R
RETURN button (48, 50, 51, 53)
This button is used to return to the previously dis-
played setup menu.
S
SETUP button (48, 50–53)
This button is used to access various settings.
For detailed information, see the pages in parentheses.
1
A & B speaker indicators (19, 36)
Indicator A lights up when speaker set A is on. Indi-
cator B lights up when speaker set B is on.
2
MUTING indicator (43)
This indicator flashes when the AV receiver is
muted.
3
Source/listening mode indicators (47, 54)
These indicators show the currently selected listen-
ing mode and digital audio format.
4
Tuning indicators
TUNED (38):
This indicator lights up when the AV
receiver is tuned to a radio station.
AUTO (38):
This indicator lights up when Auto
Tuning is selected and disappears when Manual
Tuning is selected.
RDS (European model only) (40):
This indica-
tor lights up when the AV Receiver is tuned to a
radio station that supports RDS (Radio Data Sys-
tem).
MEMORY (39):
This indicator lights up when pre-
setting radio stations.
FM STEREO (38):
This indicator lights up when
the AV receiver is tuned to a stereo FM station.
5
SLEEP indicator (43)
This indicator lights up when the Sleep function has
been set.
6
Message area
This area of the display shows various information
about the currently selected source.
Display
2134
5
6
10
Front & Rear Panels
—Continued
A
DIGITAL IN OPTICAL 1, 2 & COAXIAL
These optical and coaxial jacks can be used to con-
nect a CD or DVD player and other components
with digital audio outputs.
B
COMPONENT VIDEO
A DVD player, TV, or other component that sup-
ports component video can be connected here.
C
AM ANTENNA
These push terminals are for connecting an AM
antenna.
D
FM ANTENNA
This jack is for connecting an FM antenna.
E
MONITOR OUT
The composite video output should be connected to
a video input on your TV or projector.
F
FRONT SPEAKERS B
These push terminals are for connecting speaker
set B.
G
FRONT SPEAKERS A, SURROUND
SPEAKERS, CENTER SPEAKER &
SUBWOOFER SPEAKER
These push terminals are for connecting speaker
set A.
H
VOLTAGE SELECTOR (only some models)
This voltage selector provides compatibility with
power systems around the world.
I
This (Remote Interactive) jack can be con-
nected to the jack on another Onkyo compo-
nent. The AV receiver’s remote controller can then
be used to control that component.
To use , you must make an analog audio connec-
tion (RCA) between the AV receiver and the other
component, even if they are connected digitally.
Note:
can only be used with Onkyo components.
J
CD IN
These analog inputs can be used to connect a CD
player with analog outputs.
K
TAPE IN/OUT
These analog inputs and outputs can be used to con-
nect a cassette recorder, MiniDisc recorder, or other
recorder with analog inputs and outputs.
L
VIDEO 1 IN/OUT, VIDEO 2 IN & VIDEO 3 IN
The VIDEO 1, composite video, and audio inputs
and outputs can be used to connect a VCR. The
VIDEO 2, VIDEO 3, composite video, and audio
inputs can be used to connect another video source
(e.g., cable TV, satellite TV, or a set-top box).
M
DVD IN
The FRONT, SURROUND, CENTER, and SUB-
WOOFER jacks can be used to connect a compo-
nent with an analog multichannel audio output, such
as a DVD player with a 5.1-channel analog output.
The composite video input should be connected to a
video output on the DVD player.
Rear Panel
9 J K L M
1 B 3 4 5 876
See pages 19–33 for connection information.
11
Speaker Package
A
Speaker terminals
These push terminals are for connecting the speaker
to the HT-R340 with the supplied speaker cables.
The supplied speaker cables are color-coded for
easy identification. Simply connect each cable to the
same-colored positive speaker terminal.
B
Keyhole slots
These keyhole slots can be used to wall-mount the
speaker. See page 21 for mounting instructions.
C
Speaker mount/bracket inserts
These threaded inserts can be used to attach the
speaker to a speaker mount or bracket. See page 21
for mounting instructions.
Note:
Use commercially available machine screws to
attach the speaker to a speaker mount or bracket.
North American models require 1/4-inch screws.
Other models require M5 (5 mm) screws.
Caution:
The front grilles are not designed to be removed so
do not attempt to remove them forcibly, as this will
damage them.
Front, Center, Surround, & Subwoofer speakers
(SKF-350F, SKC-350C, SKM-350S, SKW-350)
3
2
3
2
2
1
1
3 1
1
22
■ Rear
SKF-350F
SKC-350C
SKW-350
SKM-350S
12
Remote Controller
Including the AV receiver, the remote controller can be
used to control up to six different components. The
remote controller has a specific operating mode for use
with each type of component. Modes are selected by
using the five REMOTE MODE buttons.
■
RECEIVER/TAPE Mode
In RECEIVER/TAPE mode, you can control
the AV receiver and an Onkyo cassette
recorder connected via .
■
DVD, CD, MD, CDR & HDD Modes
With these modes, you can control an Onkyo
DVD player and CD/MD/CDR/HDD
player/recorder.
Note:
Some of the remote controller operations described in
this manual may not work as expected with other com-
ponents.
RECEIVER mode is used to control the AV receiver.
To set the remote controller to RECEIVER mode,
press the [RECEIVER] REMOTE MODE button.
How to Use the Remote Controller
1
Use the REMOTE MODE buttons to select
a mode.
2
Use the buttons supported by that mode
to control the component.
RECEIVER mode: see right column
DVD mode: see page 14
CD mode: see page 15
MD/CDR mode: see page 16
HDD mode: see page 17
TAPE mode: see page 18
TAPE
RECEIVER
HDD
CDR
MD
DVD
C
D
RECEIVER Mode
MUTING
MENU
TOP MENU
SP A
/
B
SETUPRETURN
PLAYLIST PLAYLIST
RANDOM
SUBTITLE
PLAY MODE
AUDIO REPEAT
RC
-
646S
--
/
---
TAPE
ON/STANDBY
DIMMER SLEEP
INPUT SELECTOR
REMOTE MODE
V
1
V
2
V
3
C
DTAPE TUNER
DVD
MULTI CH
LISTENING MODE
DISPLAY
OR-EQ
TEST
TONE
CH SEL
SURROUND
STEREO
CINE FLTR
LEVEL
+
LEVEL
-
L NIGHT
VOL
HDD
CDR
MD
DVD
RECEIVER
C
D
+
10
0
CLR
123
456
789
ENTER
CH
DISC
ALBUM
9
K
J
7
L
P
5
4
8
2
3
A
N
M
O
Q
R
S
6
TAPE
RECEIVER
13
Remote Controller
—Continued
For detailed information, see the pages in parentheses.
A
ON/STANDBY button (34)
This button is used to set the AV receiver to On or
Standby.
B
INPUT SELECTOR buttons (36)
These buttons are used to select the input sources.
C
MULTI CH button (37)
This button is used to select the multichannel DVD
input.
D
DIMMER button (42)
This button is used to adjust the display brightness.
E
CH +/– button (39)
This button is used to select radio presets.
F
SP A/B button (36)
This button is used to turn speaker sets A and B on
or off.
G
Arrow [ ]/[ ]/[ ]/[ ] & ENTER buttons
(48, 50–53)
These buttons are used to select and adjust settings.
H
RETURN button (48, 50, 51, 53)
This button is used to return to the previous display
when changing settings.
I
LISTENING MODE buttons (46)
These buttons can be used to select listening modes
regardless of the currently selected remote control-
ler mode.
STEREO button
This button selects the Stereo listening mode.
SURROUND button
This button selects the Dolby and DTS listening
modes.
[ ]/[ ] buttons
These buttons can be used to select any of the avail-
able listening modes.
J
TEST TONE, CH SEL, LEVEL- & LEVEL+
buttons (34, 44, 51)
These buttons are used to adjust the level of each
speaker.
K
DISPLAY button (37)
This button is used to display various information
about the currently selected input source.
L
REMOTE MODE buttons (12)
These buttons are used to select the remote control-
ler modes. When you press a button on the remote
controller, the REMOTE MODE button for the cur-
rently selected mode lights up.
M
SLEEP button (43)
This button is used to set the Sleep function.
N
VOL [ ]/[ ] button (36)
This button can be used to adjust the volume of the
AV receiver regardless of the currently selected
remote controller mode.
O
MUTING button (43)
This button is used to mute the AV receiver.
P
SETUP button (48, 50–53)
This button is used to access various settings.
Q
CINE FLTR button (49)
This button is used to set the CinemaFILTER func-
tion.
R
L NIGHT button (49)
This button is used to set the Late Night function.
S
OR-EQ button (43)
This button is used to turn on the OptiResponse
Equalizer, which optimizes performance when the
HT-R340 is used with the speakers included in the
HTP-350 Home Theater Speaker Package. When
the OptiResponse Equalizer is on, you can enjoy a
powerful sound with movies or music even at low
volume levels.
14
Remote Controller
—Continued
To set the remote controller to DVD mode, press the
[DVD] REMOTE MODE button.
A
ON/STANDBY button
This button sets the DVD player to On or Standby.
B
Number buttons
These buttons are used to enter title, chapter, and
track numbers and to enter times for locating spe-
cific points in time.
C
DISC +/– button
This button selects discs on a DVD changer.
D
TOP MENU button
This button is used to select a DVD’s top menu.
E
Arrow [ ]/[ ]/[ ]/[ ] & ENTER buttons
These buttons are used to navigate DVD menus and
the DVD player’s onscreen setup menus.
F
RETURN button
This button is used to exit the DVD player’s
onscreen setup menu and to restart menu playback.
G
Playback buttons
From left to right: Pause, Play, Stop, Fast Reverse,
Fast Forward, Previous, and Next.
H
SUBTITLE button
This button is used to select subtitles.
I
AUDIO button
This button selects foreign language soundtracks
and audio formats (e.g., Dolby Digital or DTS).
J
DISPLAY button
This button is used to display information about the
current disc, title, chapter, or track on the DVD
player’s display, including the elapsed time, remain-
ing time, total time, and so on.
K
CLR button
This button is used to cancel functions and to clear
entered numbers.
L
MENU button
This button is used to display a DVD’s menu.
M
SETUP button
This button is used to access the DVD player’s
onscreen setup menus.
N
RANDOM button
This button is used with the random playback func-
tion.
O
REPEAT button
This button is used to set the repeat playback func-
tions.
P
PLAY MODE button
This button is used to select play modes on a com-
ponent with selectable play modes.
DVD Mode
DVD
6
To select your DVD player as the input source, press:
RECEIVER
MUTING
MENU
TOP MENU
SP A
/
B
SETUPRETURN
PLAYLIST PLAYLIST
RANDOM
SUBTITLE
PLAY MODE
AUDIO REPEAT
RC
-
646S
--
/
---
TAPE
ON/STANDBY
DIMMER SLEEP
INPUT SELECTOR
REMOTE MODE
V
1
V
2
V
3
C
DTAPE TUNER
DVD
MULTI CH
LISTENING MODE
DISPLAY
OR-EQ
TEST
TONE
CH SEL
SURROUND
STEREO
CINE FLTR
LEVEL
+
LEVEL
-
L NIGHT
VOL
HDD
CDR
MD
DVD
RECEIVER
C
D
+
10
0
CLR
123
456
789
ENTER
CH
DISC
ALBUM
1
6
7
L
P
5
4
8
2
3
N
M
O
9
J
DVD
K
15
Remote Controller
—Continued
To set the remote controller to CD mode, press the
[CD] REMOTE MODE button.
A
ON/STANDBY button
This button sets the CD player to On or Standby.
B
Number buttons
These buttons are used to enter track numbers and
to enter times for locating specific points in time.
C
DISC +/– button
This button selects discs on a CD changer.
D
Playback buttons
From left to right: Pause, Play, Stop, Fast Reverse,
Fast Forward, Previous and Next.
E
DISPLAY button
This button is used to display information about the
current disc or track on the CD player’s display,
including the elapsed time, remaining time, total
time, and so on.
F
CLR button
This button is used to cancel functions and to clear
entered numbers.
G
RANDOM button
This button is used with the random playback func-
tion.
H
REPEAT button
This button is used to set the repeat playback func-
tions.
✽
The VOL [ ]/[ ] and LISTENING MODE but-
tons work the same as for RECEIVER mode.
CD Mode
C
D
9
To select your CD player as the input source, press:
RECEIVER
MUTING
MENU
TOP MENU
SP A
/
B
SETUPRETURN
PLAYLIST PLAYLIST
RANDOM
SUBTITLE
PLAY MODE
AUDIO REPEAT
RC
-
646S
--
/
---
TAPE
ON/STANDBY
DIMMER SLEEP
INPUT SELECTOR
REMOTE MODE
V
1
V
2
V
3
C
DTAPE TUNER
DVD
MULTI CH
LISTENING MODE
DISPLAY
OR-EQ
TEST
TONE
CH SEL
SURROUND
STEREO
CINE FLTR
LEVEL
+
LEVEL
-
L NIGHT
VOL
HDD
CDR
MD
DVD
RECEIVER
C
D
+
10
0
CLR
123
456
789
ENTER
CH
DISC
ALBUM
1
6
5
4
7
2
3
8
C
D
✽
✽
16
Remote Controller
—Continued
To set the remote controller to MD or CDR mode,
press the [MD] or [CDR] REMOTE MODE button.
A
ON/STANDBY button
This button sets the MD/CD recorder to On or
Standby.
B
Number buttons
These buttons are used to enter track numbers and
to enter times for locating specific points in time.
The [+10] button is used to enter numbers above 10.
C
Playback buttons
From left to right: Pause, Play, Stop, Fast Reverse,
Fast Forward, Previous and Next.
D
DISPLAY button
This button is used to display information about the
current disc or track on the MD/CD recorder’s dis-
play, including the elapsed time, remaining time,
total time, and so on.
E
CLR button
This button is used to cancel functions and to clear
entered numbers.
F
RANDOM button
This button is used with the random playback func-
tion.
G
REPEAT button
This button is used to set the repeat playback func-
tions.
H
PLAY MODE button
This button is used to select play modes on a com-
ponent with selectable play modes.
✽
The VOL [ ]/[ ] and LISTENING MODE but-
tons work the same as for RECEIVER mode.
MD, & CDR Mode
TAPE
7
To select your MiniDisc or CD recorder as the input
source, press:
RECEIVER
*You must change the Input Display (see page 35).
MD or CD recorder
MUTING
MENU
TOP MENU
SP A
/
B
SETUPRETURN
PLAYLIST PLAYLIST
RANDOM
SUBTITLE
PLAY MODE
AUDIO REPEAT
RC
-
646S
--
/
---
TAPE
ON/STANDBY
DIMMER SLEEP
INPUT SELECTOR
REMOTE MODE
V
1
V
2
V
3
C
DTAPE TUNER
DVD
MULTI CH
LISTENING MODE
DISPLAY
OR-EQ
TEST
TONE
CH SEL
SURROUND
STEREO
CINE FLTR
LEVEL
+
LEVEL
-
L NIGHT
VOL
HDD
CDR
MD
DVD
RECEIVER
C
D
+
10
0
CLR
123
456
789
ENTER
CH
DISC
ALBUM
1
5
4
3
6
2
7
8
MD
CDR
✽
✽
17
Remote Controller
—Continued
To set the remote controller to HDD mode, press the
[HDD] REMOTE MODE button.
A
ON/STANDBY button
This button sets the HDD component to On or
Standby.
B
ALBUM +/– button
This button selects the next or previous album on an
HDD component.
C
PLAYLIST [ ]/[ ] buttons
These buttons select the previous or next playlist on
the HDD component.
D
Playback buttons
From left to right: Pause, Play, Stop, Fast Reverse,
Fast Forward, Previous and Next.
E
DISPLAY button
This button turns on the HDD component’s display
for 30 seconds.
F
MENU, ENTER, and Up and Down [ ]/[ ]
buttons
MENU button:
Displays the HDD component’s
menu.
[ ]/[ ] buttons:
Select options on the HDD
component’s menu.
ENTER button:
Confirms the selection on the
HDD component’s menu.
G
RANDOM button
This button is used with the random playback func-
tion.
H
REPEAT button
This button is used to set the repeat playback func-
tions.
HDD Mode
TAPE
7
To select your HDD component as the input source,
press:
RECEIVER
*You must change the Input Display (see page 35).
3
V
3
or
MUTING
MENU
TOP MENU
SP A
/
B
SETUPRETURN
PLAYLIST PLAYLIST
RANDOM
SUBTITLE
PLAY MODE
AUDIO REPEAT
RC
-
646S
--
/
---
TAPE
ON/STANDBY
DIMMER SLEEP
INPUT SELECTOR
REMOTE MODE
V
1
V
2
V
3
C
DTAPE TUNER
DVD
MULTI CH
LISTENING MODE
DISPLAY
OR-EQ
TEST
TONE
CH SEL
SURROUND
STEREO
CINE FLTR
LEVEL
+
LEVEL
-
L NIGHT
VOL
HDD
CDR
MD
DVD
RECEIVER
C
D
+
10
0
CLR
123
456
789
ENTER
CH
DISC
ALBUM
1
5
4
7
2
8
HDD
6
3
18
Remote Controller
—Continued
TAPE mode is used to control an Onkyo cassette
recorder connected to the AV receiver via .
To set the remote controller to TAPE mode, press the
[RECEIVER] REMOTE MODE button.
For twin cassette decks, only deck B can be controlled.
A
Play [ ] button
This button is used to start playback.
B
Stop [ ] button
This button is used to stop playback.
C
Reverse Play [ ] button
This button is used to start reverse playback.
D
Rewind & FF [ ]/[ ] buttons
The Rewind [ ] button is used to start rewind. The
FF [ ] button is used to start fast forward.
TAPE Mode
TAPE
7
To select your Cassette deck as the input source,
press:
RECEIVER
MUTING
MENU
TOP MENU
SP A
/
B
SETUPRETURN
PLAYLIST PLAYLIST
RANDOM
SUBTITLE
PLAY MODE
AUDIO REPEAT
RC
-
646S
--
/
---
TAPE
ON/STANDBY
DIMMER SLEEP
INPUT SELECTOR
REMOTE MODE
V
1
V
2
V
3
C
DTAPE TUNER
DVD
MULTI CH
LISTENING MODE
DISPLAY
OR-EQ
TEST
TONE
CH SEL
SURROUND
STEREO
CINE FLTR
LEVEL
+
LEVEL
-
L NIGHT
VOL
HDD
CDR
MD
DVD
RECEIVER
C
D
+
10
0
CLR
123
456
789
ENTER
CH
DISC
ALBUM
B
C
D
A
TAPE
RECEIVER
Loading...