lg DU-42PZ60A, DU-42PZ60B, DU-42PZ60C, DU-42PZ60K, DU-42PZ60R OWNER’S MANUAL

PLASMA TV

OWNER’S MANUAL

MODELS:

DU-42PZ60/60A/60B/60C/60K/60R/60S DU-42PZ60H/60HA/60HB/60HC/60HK/60HR/60HS DU-42PZ70/70A/70B/70C/70K/70R/70S DU-42PZ70H/70HA/70HB/70HC/70HK/70HR/70HS DU-50PZ60/60A/60B/60C/60K/60R/60S DU-50PZ60H/60HA/60HB/60HC/60HK/60HR/60HS DU-50PZ70/70A/70B/70C/70K/70R/70S DU-50PZ70H/70HA/70HB/70HC/70HK/70HR/70HS

Please read this manual carefully and completely before operating your TV.

Retain this manual for future reference.

Record model number and serial number of the TV in the spaces provided below.

See the label attached on the back cover and relate this information to your dealer if you require service.

Model Number :

Serial Number :

Internet Home Page : http://www.lge.com

Warning

Warning

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

COMPLIANCE:

The responsible party for this product’s compliance is:

LG Electronics.

CAUTION:

Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product.

Marketed and Distributed in the United States by LG Electronics U.S.A., Inc. 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632

2 Plasma TV

Safety Instructions

Safety Instructions

Important safeguards for you and your new product

Your product has been manufactured and tested with your safety in mind. However, improper use can result in electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference.

Observing the simple precautions discussed in this manual can help you get many years of enjoyment and safe operation that are built into your new product.

This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.

1. Read Instructions	9. Attachments
All the safety and operating instructions should be read	Do not use attachments not recommended by the product
before the product is operated.	manufacturer as they may cause hazards.

2. Follow Instructions

All operating and use instructions should be followed.

3. Retain Instructions

The safety and operating instructions should be retained for future reference.

4. Heed Warnings

All warnings on the product and in the operating instructions should be adhered to.

5. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6. Water and Moisture

Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.

7. Accessories, Carts, and Stands

Do not place this product on a slippery or tilted surface, or on an unstable cart, stand, tripod, bracket, or table. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

8. Transporting Product

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

10. Ventilation

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

11. Power Sources

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12. Power-Cord Polarization

This product is equipped with a three-wire grounding type plug, a plug having a third (grounding) pin. This plug will only fit into the grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

13. Power-Cord Protection

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

PORTABLE CART WARNING

Owner’s Manual 3

Safety Instructions

Safety Instructions continued

14. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-dis- charge unit, connection to grounding electrodes, and requirements for the grounding electrode.

Example of Grounding According to National Electrical Code Instructions

Ground Clamp

				Antenna Lead in Wire
				Antenna Discharge Unit
				(NEC Section 810-20)
				Grounding Conductor
Electric Service				(NEC Section 810-21)
Equipment				Ground Clamps
				Power Service Grounding
				Electrode System (NEC
				Art 250, Part H)

NEC - National Electrical Code

15. Lightning

For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

16. Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

17. Overloading

Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

18. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

19. Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a.If the power-supply cord or plug is damaged.

b.If liquid has been spilled, or objects have fallen into the product.

c.If the product has been exposed to rain or water.

d.If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.

e.If the product has been dropped or the cabinet has been damaged.

f.If the product exhibits a distinct change in performance.

21. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

22. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

23. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product.

24. Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

4 Plasma TV

Contents

Contents

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4

Introduction

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Connection Options . . . . . . . . . . . . . . . . . . . . . .8

Remote Control Key Functions . . . . . . . . . . . . . .9

Installation

Installation Instruction . . . . . . . . . . . . . . . . . . . . . .10

External Equipment Connections . . . . . . . . . .11~15

Antenna Connection . . . . . . . . . . . . . . . . . . . . .11

VCR Setup / Cable TV Setup . . . . . . . . . . . . . .12

External A/V Source Setup . . . . . . . . . . . . . . . .13

Monitor Out Setup / DVD Setup . . . . . . . . . . . .13

HDSTB Setup / Digital Audio Output . . . . . . . . .14

PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Operation

Screen Setup for PC mode

Adjustments for screen position, clock, and phase . .16

Turning the TV On . . . . . . . . . . . . . . . . . . . . . . . .17

On-screen Menus Language Selection . . . . . . . . .17

Setup Menu Options

EZ Scan (Channel Search) . . . . . . . . . . . . . . . .18

Channel Edit . . . . . . . . . . . . . . . . . . . . . . . . . . .18

DTV Signal Strength . . . . . . . . . . . . . . . . . . . . .19

Channel Label Setup . . . . . . . . . . . . . . . . . . . .19

Main Picture Source Selection . . . . . . . . . . . . .20

Front LED (Light Emitting Diode) Display . . . . .20

Video Menu Options

EZ Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Manual Picture Control (User Option) . . . . . . . .21

Color Temperature Control . . . . . . . . . . . . . . . .21

Video Preset . . . . . . . . . . . . . . . . . . . . . . . . . .21

Audio Menu Options

Audio Language . . . . . . . . . . . . . . . . . . . . . . . .22

EZ SoundRite / EZ Sound . . . . . . . . . . . . . . . . .22

Manual Sound Control (User Option) . . . . . . . .22

Stereo/SAP Broadcasts Setup . . . . . . . . . . . . .23

Front Surround . . . . . . . . . . . . . . . . . . . . . . . . .23

TV Speakers On/Off Setup . . . . . . . . . . . . . . . .23

Time Menu Options

Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . .24 Manual Clock Setup . . . . . . . . . . . . . . . . . . . . .24 On/Off Timer Setup . . . . . . . . . . . . . . . . . . . . .24 Sleep Timer / Auto Off . . . . . . . . . . . . . . . . . . . .25

Option Menu Features

Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Caption / Caption Mode . . . . . . . . . . . . . . . . . .27 Caption Option / EZ Demo . . . . . . . . . . . . . . . .28 ISM Method . . . . . . . . . . . . . . . . . . . . . . . . . . .28 White Wash . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Low power . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Lock Menu Options

Parental Lock Setup . . . . . . . . . . . . . . . . . . . . .31 PIP (Picture-in-Picture)/Twin Picture

Watching PIP/POP/Twin Picture . . . . . . . . . . . ..32 Selecting an Input Signal Source for PIP/Twin Picture . .32 Swapping PIP/Twin Picture . . . . . . . . . . . . . . . .32

TV Program Selection for PIP . . . . . . . . . . . . . .32 Moving the PIP sub picture . . . . . . . . . . . . . . . .33 Adjusting Main and Sub Picture Sizes for Twin Picture . .33 POP (Picture-out-of-Picture: Channel Scan) . . .33

External Control Device Setup . . . . . . . . . . . . . . .	.34~38
IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	39~40
Programming the Remote . . . . . . . . . . . . . . . . . . .	. . .41
Programming Codes . . . . . . . . . . . . . . . . . . . . . . .	42~43
Troubleshooting Checklist . . . . . . . . . . . . . . . . . . .	. . .44
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . .45
Product Specifications . . . . . . . . . . . . . . . . . . . . . .	. . .46
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	47~48

Setup and Operation Checklist

Setup and Operation Checklist

(See pages 11~15 for available connection and operational setup options.)

1.Unpack TV and all accessories.

2.Connect all external video and audio equipment. see pages 12 ~ 14.

3Install batteries in remote control. See page 9.

4.Turn TV on. See page 17.

5.Turn video source equipment on.

6.Select viewing source for TV. See page 20.

7.Fine-tune source image and sound to your personal preference or as required by source.

See pages 21 ~ 23.

8.Additional features set up See Contents above.

After reading this manual, keep it handy for future reference.

Owner’s Manual 5

Introduction

Introduction

What is a Plasma Display Panel (PDP)?

A plasma display panel is the latest display technology and the best way to achieve flat panel displays with excellent image quality and large screen sizes that are easily viewable. The PDP can be thought of as a descendant of the neon lamp and it can be also be viewed as a series of fluorescent lamps.

How does it work?

PDP is an array of cells, known as pixels, which are comprised of 3 sub pixels, corresponding to the colors red, green, and blue.

Gas in a plasma state is used to react with phosphors in each sub-pixel to produce colored light (red, green, or blue). These phosphors are the same types used in Cathode Ray Tube (CRT) devices such as televisions and common computer monitors.

You get the rich, dynamic colors that you expect. Each sub-pixel is individually controlled by advanced electronics to produce over 16 million different colors. All of this means that you get perfect images that are easily viewable in a display that is less than 5 inches thick.

160° - Wide angle range of vision

Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is clear and visible to viewers anywhere in the room who can see the screen.

Wide Screen

The screen of the Plasma Display is so wide that your viewing experience is as if you are in a theater.

Multimedia

Connect your plasma display to a PC and you can use it for conferencing, games, and Internet browsing. The Picture-in-Picture feature allows you to view your PC and video images simultaneously.

Versatile

The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs will not fit.

The PDP Manufacturing Process: a few minute colored dots may be present on the PDP screen

The PDP (Plasma Display Panel), which is the display device of this product is composed of 0.9 to 2.2 million cells. A few cell defects will normally occur in the PDP manufacturing process. Several tiny, minute colored dots visible on the screen should be acceptable. This also occurs in other PDP manufacturers' products. The tiny dots appearing does not mean that this PDP is defective. Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology minimizes these cell defects during the manufacture and operation of this product.

Cooling Fan Noise

In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the PDP is equipped with cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operating and cooling the PDP.

The fan noise doesn't have any negative effect on the PDP's efficiency or reliability. The noise from these fans is normal during the operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable and is not sufficient cause for the PDP to be exchanged or returned.

6 Plasma TV

Introduction

Controls

-This is a simplified representation of front panel.

Here shown may be somewhat different from your TV.

-This manual explains the features available on the DU-50PZ60/70 series TVs.

		Front Panel Controls
			Remote Control Sensor
ON/OFF S-VIDEO VIDEO	AUDIO	TV/VIDEO MENU VOL	CH

ON/OFF

S-VIDEO

A/V INPUT 2
VIDEO L/MONO AUDIO	R

VOL

CH

AUDIO Input

Power Button

Use to connect

stereo sound

external device.

VIDEO Input

Power Standby Indicator

Connects the video signal

from a video device.

Illuminates red in standby mode,

Illuminates green when the TV is

turned on.

S-VIDEO Input

A connection available to provide better

picture quality than the video input.

CHANNEL (E, D) Buttons

VOLUME (F,G) Buttons

Owner’s Manual 7

Introduction

Connection Options

Back Connection Panel

DVD/DTV Input (Component 1-2)

Connect a component video/audio device to these jacks.

S-Video Input

Digital Audio (DVI: Digital Visual

Connect S-Video out from an S-VIDEO

device to the S-VIDEO input.

Interface/Component1) Input/

Digital Audio Output

Connect digital audio from various types

Monitor Output

Remote Control Port

of equipment. Note: In standby mode,

Connect a second TV or

Connect your wired remote

these ports will not work.

Monitor.

control here.

AUDIO INPUT

VIDEO INPUT

DVI

COMPONENT1

R

L

R AUDIO

L

VIDEO

INPUT OUTPUT

INPUT

COMPONENT 2

DVD

MONITOR

R

L

Antenna1

Antenna 2

RGB INPUT

OUTPUT

AUDIO INPUT

DVI INPUT

/DTV

RS-232C INPUT

REMOTE

INPUT

A/V

EXTERNAL SPEAKER

AC INPUT

COMPONENT 1

S-VIDEO (CONTROL/SERVICE)

CONTROL

DIGITAL AUDIO

INPUT1

(MONO)

(OPTICAL)

								Audio/Video Input 1
	Antenna 1-2 Inputs						Connect audio/video output from an
	Connect cable or antenna							external device to these jacks.
	signals to the TV, either
	directly or through your							External Speaker (8 ohm Output)
	cable box. For DTV use
								Connect to optional external speaker(s).
	Antenna 2 only.
								* For further information, refer to ‘Speaker &
								Speaker Stand’ manual.
				RGB Input/Audio Input/DVI Input

Connect the monitor output connector from a PC to the appropriate input port.

Power Cord Socket

This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power.

- This manual explains the features available on the DU-50PZ60/70 series TVs.

8 Plasma TV

Installation

Remote Control Key Functions

- When using the remote control, aim it at the remote control sensor on the TV.

LIGHT

MODE

Illuminates the remote control buttons.

TV/VIDEO
Selects: DTV, Analog, Video1-2,
Component 1-2, RGB-DTV (or RGB-PC),
DVI-DTV (or DVI-PC) input sources.
				LIGHT
COMP/RGB/DVI				TV/VIDE			O
Selects: Component 1-2, RGB-DTV (or RGB-
PC), DVI-DTV (or DVI-PC) input sources.
NUMBER buttons
DASH
Used to enter a program number for multiple
program channels such as 2— 1,2— 2,etc.
MUTE				MUTE
Switches the sound on or off.
VOLUME UP/DOWN
Increases/decreases the sound level.				INFO
INFO
When you watch the TV, displays information
on top of the screen. Not available in
Component 1-2, RGB and DVI mode.
SAP
Selects MTS sound: Mono, Stereo, and SAP.				MENU
Change the audio language in DTV mode.
				PLAY
THUMBSTICK (Up/Down/Left/Right/OK)
Allows you to navigate the on-screen				REW
menus and adjust the system settings to
your preference.				PIP
MENU
Brings up the main menu to the screen.				FREEZE
SOUND				ADJUST
Selects the sound appropriate
for the program's character.
FREEZE
Freezes the currently-viewed picture. Main
picture is frozen in PIP/Twin picturre mode.
ADJUST

				Selects the remote operating mode: TV,
				VCR, DVD, CABLE, HDSTB or AUDIO.
				Select other operating modes, for the
				remote to operate external devices.
			POWER	POWER
	MODE			Turns your TV or any other programmed
	COMP/RGB/DVI		TIMER	equipment on or off, depending on mode.
				TIMER
				Lets you select the amount of time before
				your TV turns itself off automatically.
		FLASHBK		FLASHBK
				Tunes to the last channel viewed.
			SURF	SURF
				Use to scroll the Surf channel list.
	VOL	CH
				CHANNEL UP/DOWN
	SAP	RATIO		Selects available channels found
			CC	with EZ scan.
				RATIO
				Changes the aspect ratio.
	OK			CC
				Select a closed caption:
				Off, EZ Mute, and On.
			EXIT	EXIT
	SOUND	VIDEO
				Clears all on-screen displays and returns to
	PAUSE	STOP	RECORD	TV viewing from any menu.
	FF	SKIP		VIDEO
				Adjusts the factory preset picture according
	PIPCH-	PIPCH+	PIPINPUT	to the room.
	ZOOM	SIGNAL	SWAP	VCR/DVD BUTTONS
				Control some video cassette recorders or
				DVD player ("RECORD" button is not avail-
				able for DVD player).
				PIP
				Switches between PIP, POP (Picture-out-of-
				Picture) and Twin picture modes.
				PIPCH-/PIPCH+
				Changes to next higher/lower PIP channel.

Adjusts screen position, clock, and phase in PC mode.

ZOOM

Enlarges the main picture size.

SIGNAL

Displays the digital signal strength.

PIP INPUT

Selects the input source for the sub picture.

SWAP

Exchanges the PIP/main images.

Installing Batteries

•Open the battery compartment cover on the back side and install the batteries matching correct polarity (+ with +, - with -).

•Install two 1.5V AA batteries. Don’t mix old or used batteries with new ones. Replace cover.

Owner’s Manual 9

Installation

Installation

Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product.

	1.5V
Owner’s Manual	Batteries	Power Cord	75Ω Round Cable	Remote Control

Installation Instructions

•The TV can be installed in various ways such as on a wall, or on a desktop etc.

•The TV is designed to be mounted horizontally. The speakers shown are optional.

GROUNDING

Ensure that you connect the grounding / earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.

Power

Supply

Short-circuit

Breaker

Wall Mount: Horizontal installation

Desktop Pedestal Installation

For proper ventilation, allow a clearance of 4” on each side and 2” from the wall. Detailed installation instructions are available from your dealer, see the optional Wall Mounting Bracket Installation and Setup Guide.

	2 inches
	4 inches
4 inches	4 inches
	4 inches

For proper ventilation, allow a clearance of 4” on each side and the top, 2.36” on the bottom, and 2” from the wall. Detailed installation instructions are included in the optional Desktop Stand Installation and Setup

Guide available from your dealer.

4 inches

2 inches

4 inches

4 inches

2.36 inches

10 Plasma TV

Installation

External Equipment Connections

Antenna Connection

Analog and Digital TV signals provided on one antenna

a Cable Box Connections

antenna direction if needed.

Multi-family Dwellings/Apartments (Connect to wall antenna socket)

Wall Antenna

Socket

Bronze Wire

RF Coaxial Wire (75 ohm)

			DVI	COMPONENT1
Antenna 2			INPUT OUTPUT	INPUT
	RGB INPUT	AUDIO INPUT	DVI INPUT
			DIGITAL AUDIO
			(OPTICAL)

VHF Antenna	Turn clockwise to tighten.
UHF Antenna
		Bronze Wire
	Outdoor
	Antenna	Be careful not to bend the bronze wire when
Single-family Dwellings /Houses		connecting the antenna.
(Connect to wall jack for outdoor antenna)
Plasma TV		• In a poor signal area to improve picture quality, purchase
		and install a signal amplifier.

needs to be split for two TV’s, install a “2- ” in the connections.

RGB INPUT	AUDIO INPUT DVI INPUT	COMPONENT1	not installed properly, contact your deal-
	DVI
	INPUT OUTPUT	INPUT
	(OPTICAL)		Signal
	DIGITAL AUDIO
			Amplifier

Analog and Digital TV signals provided on two separate antennas

Wall Antenna	Bronze Wire
Socket	RF Coaxial Wire (75 ohm)
	Analog Antenna
Wall Antenna	Turn clockwise to tighten.
Socket	RF Coaxial Wire (75 ohm)

Antenna1

Antenna 2

RGB INPUT

AUDIO INPUT

DVI INPUT

Digital Antenna

Bronze Wire

NOTE: If you are not sure of the type of signal(s) you are receiving, let EZ Scan complete all the channel signal-type searches.

The TV will let you know when the analog, cable, and digital channel scans are complete.

Owner’s Manual 11

Installation

NOTE: All cables shown are not included with the TV

VCR Setup

(interference), leave an adequate distance between the VCR and TV

(on the Option menu) feature to avoid having a fixed image remain on the screen for a long period of time. picture from a VCR. If the 4:3 picture format is used; the fixed images on the sides of the screen may screen.

1

to 3 or 4 and then tune

number.

2

and video cables from the

to the TV input jacks, as

R

L

VIDEO INPUT

R AUDIO L

VIDEO

AUDIO INPUT

.

DVI

OUTPUT

COMPONENT1

MONITOR

INPUT

INPUT

COMPONENT 2

Antenna 1

Antenna 2

RGB INPUT

AUDIO INPUT DVI INPUT

DVD

OUTPUT

/DTV

RS-232C INPUT REMOTE

DIGITAL AUDIO

COMPONENT 1

INPUT

A/V

S-VIDEO

TV to VCR, match the

INPUT1

(MONO)

(CONTROL/SERVICE) CONTROL

(OPTICAL)

yellow, Audio Left = white,

.

-VIDEO output from VCR to

the picture quality is

1

to connecting a regular

.

into the VCR and press

2

(Refer to the VCR owner’s

with using the

ANT OUT

the remote control. (If

S-VIDEO

VCR

1, select Video 1

OUT

ANT IN

OUTPUT		(R) AUDIO (L)	VIDEO
SWITCH
3	4	IN

to both Video and the same time.

Cable TV Setup

cable TV service from a local provider and installing a converter, you can watch cable TV programming.

TV programming unless a TV tuner device or cable TV converter box is connected to the TV. regarding cable TV service, contact your local cable TV service provider(s).

switch on cable

the same selected box.

cable box or with the

.

AUDIO INPUT

VIDEO INPUT

DVI

COMPONENT1

R

L

R AUDIO

L

VIDEO

OUTPUT

MONITOR

INPUT

INPUT

COMPONENT 2

1

Antenna 2

RGB INPUT

DVD

OUTPUT

AUDIO INPUT

DVI INPUT

/DTV

RS-232C INPUT

REMOTE

INPUT

A/V

DIGITAL AUDIO

COMPONENT 1

INPUT1

(MONO)

S-VIDEO (CONTROL/SERVICE)

CONTROL

(OPTICAL)

video cables from the

1

to the TV input jacks,	2

to a Cable Box,
(Video = yellow, Audio
Right = red).		OUTPUT		(R) AUDIO (L)	VIDEO
with using the		SWITCH		TV
		3	4
remote control. (If	RF	Cable		VCR
1, select Video 1		Cable Box
channel with the remote

12 Plasma TV

Installation

External A/V Source Setup

the external equipas shown in the

match the

= white, and Audio

TV/VIDEO button on INPUT 1, select

. Refer to

AUDIO INPUT

VIDEO INPUT

R

L

R AUDIO L

VIDEO

COMPONENT 2		MONITOR
	DVD	OUTPUT
	/DTV				RS-232C INPUT	REMOTE
	INPUT	A/V		S-VIDEO
COMPONENT 1		INPUT1	(MONO)		(CONTROL/SERVICE)	CONTROL

Camcorder

Monitor Out Setup

R AUDIO L

VIDEO

	MONITOR
DVD	OUTPUT
/DTV				RS-232C INPUT
INPUT	A/V		S-VIDEO
	INPUT1	(MONO)		(CONTROL/SERVICE)

R AUDIO L VIDEO

Video Game Set

The TV has a special signal output capability which allows you to hook up a second TV or monitor.

Connect the second TV or monitor to the TV’s MONITOR OUTPUT.

See the Operating Manual of the second TV or monitor for further details regarding that device’s input settings.

NOTE

•Component, RGB-PC/RGB-DTV, DVI-PC/DVI-DTV, DTV input sources cannot be used for Monitor out.

IN

(R) AUDIO (L)

VIDEO

, PR) to the COMPONENT (Y,
the DVD audio outputs to
shown in the figure.
jack, connect this to the S-
DVD audio outputs to the
in the figure.				AUDIO INPUT		VIDEO INPUT
	DVI		COMPONENT1	R	L		R AUDIO L	VIDEO
component video output, use	INPUT	OUTPUT	INPUT		COMPONENT 2		MONITOR
						DVD	OUTPUT	S-VIDEO	(CONTROL/SERVICE)
	DIGITAL AUDIO				COMPONENT 1	/DTV	INPUT1
						INPUT	A/V		RS-232C INPUT
	(OPTICAL)

.

button on the remote control to

or

. (If connected to S-VIDEO,

input source.)

operating instructions.

connect a DVD player to the compobelow.

or

DIGITAL AUDIO	(R) AUDIO (L)	B	R	S-VIDEO	(R) AUDIO (L)
OPTICAL

	Y	PB	PR
	Y	Pb	Pr
	Y	B-Y	R-Y
on DVD player	Y	Cb	Cr
	Y	PB	PR

DVD

NOTES

•Digital Audio will not work for Component 2 input source.

•Digital Audio operation has priority if Digital Audio and AUDIO L/R are connected at the same time.

Owner’s Manual 13

Installation

HDSTB Setup

Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital set-top box or other digital external device, refer to the figure as shown below.

(High-bandwidth Digital Contents Protection) protocol for DTV (480p,720p,1080i) mode.

AUDIO INPUT

VIDEO INPUT

Antenna 1

Antenna 2

RGB INPUT

AUDIO INPUT

DVI INPUT

DVI

COMPONENT1

R

L

R AUDIO

L

VIDEO

INPUT

OUTPUT

INPUT

COMPONENT 2

MONITOR

R

L

DVD

OUTPUT

/DTV

RS-232C INPUT

REMOTE

INPUT

A/V

EXTERNAL SPEAKER

DIGITAL AUDIO

COMPONENT 1

INPUT1

(MONO)

S-VIDEO (CONTROL/SERVICE)

CONTROL

AC INPUT

(OPTICAL)

or

or

or

or

RGB-DTV OUTPUT (R) AUDIO (L)	(R) AUDIO (L)	DIGITAL AUDIO	DVI-DTV OUTPUT	DIGITAL AUDIO	(R) AUDIO (L)	B	R
		OPTICAL		OPTICAL

Digital Set-top Box

(Y, PB, PR) INPUT, RGB or DVI jack for on your set-top box connector. Then,

audio connections.

-top box. (Refer to the owner’s manual for the

on the remote control to select

2, RGB-DTV, or DVI-DTV source.

Digital Audio Output

Signal	Component 1/2	RGB-DTV,DVI-DTV
480i	Yes	No
480p	Yes	Yes
720p	Yes	Yes
1080i	Yes	Yes

audio equipment (stereo system) via port.

cable to the TV Digital Audio Optical

optical cable to the digital audio optical

.

- Off” in the AUDIO menu. Refer to

instruction manual for operation.

into the optical output port. at the laser beam may damage

.

AUDIO INPUT

VIDEO INPUT

		DVI		COMPONENT1	R	L
			OUTPUT
RGB INPUT		INPUT		INPUT		COMPONENT 2	DVD
	AUDIO INPUT	DVI INPUT					/DTV
							INPUT

COMPONENT 1

DIGITAL AUDIO (OPTICAL)

14 Plasma TV

Installation

PC Setup

-This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. The TV sends configuration information (EDID) to the PC using the Video Electronics Standard Association (VESA) Display Data Channel (DDC) protocol.

-The TV perceives 640x480, 60Hz as DTV 480p based on the PC graphic card. card, change the screen scanning rate for the graphic card accordingly.

picture quality, adjust the PC

1024x768, 60Hz.

INPUT or DVI (Digital Visual port for video connections,

PC connector.

card on the PC does not output

RGB simultaneously, connect RGB INPUT or DVI INPUT to

on the TV.

card on the PC does output analog simultaneously, set the TV to

DVI; (the other mode is set to Plug by the TV.)

corresponding audio connections. card, adjust the PC sound as

						AUDIO INPUT		VIDEO INPUT
				DVI	COMPONENT1	R	L
Antenna 1	Antenna 2	RGB INPUT		INPUT OUTPUT	INPUT		COMPONENT 2	DVD
			AUDIO INPUT	DVI INPUT				/DTV
							COMPONENT 1	INPUT
				DIGITAL AUDIO
				(OPTICAL)

and the TV.

by pressing the POWER button on the TV's remote control.

or DVI-PC input source in main input option of SETUP menu. (Refer to P.20)

on your TV. There may be noise associated with the resolution, vertical pattern, contrast or bright-

. If noise is present, change the PC mode to another resolution, change the refresh rate to another brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic

changed, change the PC graphic card or consult the manufacturer of the PC graphic card.

on the graphics card, DOS mode may not work if you use a DVI-I cable.

a fixed image on the TV's screen for a long period of time. The fixed image may become perimprinted on the screen. Use the Orbiter screen saver when possible.

input form for Horizontal and Vertical frequencies is separate.

Monitor Display Specifications (RGB-PC / DVI-PC Mode)

	Resolution	Horizontal	Vertical	Resolution	Horizontal	Vertical
		Frequency(KHz)	Frequency(Hz)		Frequency(KHz)	Frequency(Hz)
	640x350	31.468	70.09		35.156	56.25
		37.861	85.08		37.879	60.31
				800x600
	720x400	31.469	70.08		48.077	72.18
		37.927	85.03		46.875	75.00
		31.469	59.94		53.674	85.06
	640x480	37.861	72.80		48.363	60.00
		37.500	75.00	1024x768	56.476	70.06
		43.269	85.00		60.023	75.02

Owner’s Manual 15