ITI Part No. 60-746-01
SuperBus 2000®
2x16 LCD Alphanumeric
Touchpad
Document Number: 466-1712 Rev. B
November 2000
The SuperBus 2x16 LCD (liquid crystal display) Alphanumeric Touchpad lets you control all programming and operation of a compatible security system (see the section “Specifications”). The 2-line, 16-character display provides messages to indicate the current system status.
The touchpad includes police, fire, and auxiliary panic buttons that can be activated anytime.
A built in speaker provides alarm sounds, status sounds, and button-press beeps.
Mount the touchpad in an environmentally controlled area (32°F to 120°F) (0°C to 49°C).
Test System Weekly |
Off |
Stay |
Away |
A |
1 |
2 |
3 |
press both |
|
|
|
|
No Delay |
Silent |
Pager |
B |
4 |
5 |
6 |
press both |
|
|
|
|
Features |
System |
Menu |
C |
7 |
8 |
9 |
press both |
|
|
|
|
Status |
Lights |
Bypass |
D |
* |
0 |
# |
|
|
|
Installation Instructions
Table 1 describes the power used by the touchpad.
Current (mA) |
Condition |
|
|
|
|
90 |
Maximum alarm current |
|
|
57 |
Typical operation |
|
|
12 |
Standby current (no AC power) |
|
|
Do not exceed the maximum available power when using panel power for bus devices and hardwire detectors (see the specific panel Installation Instructions for maximum available power).
Table 2 describes the maximum wire lengths allowed between the touchpad and the panel.
When mounting the touchpad, allow at least 4¼ inches on the left side for the Quick Guide slide-out card.
For Concord Express systems, up to 4 bus devices can be connected to the panel.
For Concord systems (all software versions) up to 16 bus devices can be connected to the panel.
For Concord systems with software versions 1.0–1.6, each bus device must have a different unit number setting to operate correctly. The touchpad unit number is factory set to 001.
For Concord panels with software version 2.0 or later and Concord Express panels, bus unit numbers are assigned automatically.
Wire Gauge |
Maximum Wire Length |
(Unshielded |
Between Touchpad and |
or Shielded) |
Panel |
|
|
|
|
18 |
750 feet |
|
|
22 |
300 feet |
|
|
4-conductor, 22or 18-gauge wire
Screwdriver
Drill/bits
#6 screws and anchors (included)
Panhead screws for a gang box installation
Saw or utility knife for cutting wallboard
1
Installation
The touchpad can be installed on a wall or electrical gang box, either singleor dual-gang.
1.Separate the mounting plate from the touchpad by pressing the tab at the bottom and sliding the mounting plate down (see Figure 1).
LIFT AND PULL
MOUNTING
PLATE TAB
TAB
4.Looking at the back side of the mounting plate, turn it so the tab is on the left (see A in Figure 3) and position the Quick Guide slide-out card into the slots on back of the mounting plate as shown in Figure 3 (A). Make sure the card is unfolded and the “Zones” section is facing you.
5.Slide the card in the direction of the arrow in Figure 3 (A) until it snaps into the position shown in Figure 3 (B).
A
8581G07A.DSF
2.Place the mounting plate on the wall and mark the four mounting holes (see Figure 2). Be sure to leave a 4¼inch clearance on the left side to allow for the Quick Guide slide-out card.
WALL-MOUNTING HOLES (4)
DUAL-GANG MOUNTING HOLES (4)
SINGLE-GANG
MOUNTING HOLES (2)
SWING CARD OVER IN
DIRECTION OF ARROW
UNTIL CARD SNAPS
INTO PLACE
|
|
|
|
0 |
|
0 |
|
0 |
|
0 |
|
0 |
|
0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
8 |
|
7 |
|
|
|
|
|
|
0 |
0 |
|
|
|
|
|
|
|
|||||
|
|
|
|
6 |
5 |
|
4 |
|
|
|
Z |
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
3 |
|
2 |
_ |
|
|
|
|
|
|
|||||
|
|
|
_ |
_ |
|
|
|
|
|
|
|
|
|
|
|
|
|
1 |
O |
|
|
|
|
|
|
|
|
|
|
_ |
_ |
_ |
_ |
|
|
|
_ |
|
|
|
|
|
|
||||||||
|
|
_ |
_ |
|
_ |
|
_ |
|
_ |
N |
|
|
|
|
|
|
|||||||||
|
|
_ |
|
|
|
_ |
|
_ |
|
_ |
|
|
|
|
|
|
|
|
|||||||
|
|
_ |
_ |
_ |
|
|
|
_ |
|
_ |
E |
|
|
|
|
|
|
|
|||||||
|
_ |
_ |
|
_ |
_ |
_ |
|
|
|
|
|
|
|
|
|||||||||||
|
_ |
_ |
_ |
|
_ |
S |
|
|
|
|
|
|
|
||||||||||||
|
_ |
_ |
_ |
|
_ |
|
_ |
|
_ |
_ |
_ |
|
|
|
|
|
|
|
|
|
|
||||
_ |
_ |
_ |
|
|
|
_ |
|
_ |
|
_ |
|
|
|
|
|
|
|
|
|
|
|
||||
_ |
|
_ |
_ |
_ |
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
_ |
_ |
_ |
|
_ |
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
_ |
_ |
_ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
WIRE
ACCESS
AREA
8581G02A.DS4
B
00000000 Z12345678 N O________
__ __ __ __ __ __ __ __ ES __ __ __ __ __8581G08A.DSF__ __ __
_ _ _ _ _ _ _ _ Figure 3. Inserting the Quick Guide Slide-Out Card into _ _ _ _ _ _ _ _ the Mounting Plate
6.Position the mounting plate in its normal mounting position (tab at the bottom) and fold the card toward you at all three scored lines. The “Zones” section should be facing you and the folds should create a tab to slide the card in and out.
2