Loading...
Operator′s manual
K3000
K3000 Wet
Please read the operator’s manual carefully and make sure you understand the instructions
before using the machine.
English
KEY TO SYMBOLS
Symbols on the machine:
WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fatal injury to the operator or others.
Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.
Always wear:
• Approved protective helmet
• Approved hearing protection
• Protective goggles or a visor
This product is in accordance with applicable EC directives.
WARNING! Dust forms when cutting, which can cause injuries if inhaled. Use an approved breathing mask. Always provide for good ventilation.
WARNING! Sparks from the cutting blade can cause fire in combustible materials such as: petrol (gas), wood, dry grass etc.
WARNING! Kickbacks can be sudden, rapid and violent and can cause life threatening injuries. Read and understand the instructions in the manual before using the machine.
Environmental marking. Symbols on the product or its packaging indicate that this product cannot be handled as domestic waste. It must instead be submitted to an appropriate recycling station for the recovery of electrical and electronic equipment.
By ensuring that this product is taken care of correctly, you can help to counteract the potential negative impact on the environment and people that can otherwise result through the incorrect waste management of this product.
For more detailed information about recycling this product, contact your municipality, your domestic waste service or the shop from where you purchased the product.
Other symbols/decals on the machine refer to special certification requirements for certain markets.
2 – English
Symbols in the operator’s manual:
Inspection and/or maintenance should be carried out with the motor switched off and the plug disconnected.
Always wear approved protective gloves.
Regular cleaning is required.
Visual check.
Protective goggles or a visor must be worn.
|
CONTENTS |
Contents |
|
KEY TO SYMBOLS |
|
Symbols on the machine: ..................................... |
2 |
Symbols in the operator’s manual: ....................... |
2 |
CONTENTS |
|
Contents ............................................................... |
3 |
WHAT IS WHAT? |
|
What is what on the power cutter - K3000? ......... |
4 |
WHAT IS WHAT? |
|
What is what on the power cutter - K3000 Wet? .. 5
GENERAL SAFETY PRECAUTIONS |
|
Steps before using a new power cutter ................ |
6 |
Personal protective equipment ............................. |
6 |
Machine′s safety equipment ................................. |
7 |
SAFETY INSTRUCTIONS |
|
General safety warnings ....................................... |
9 |
Cutting blades ...................................................... |
11 |
General working instructions ................................ |
13 |
ASSEMBLY |
|
Assembly .............................................................. |
15 |
Fitting the cutting blade ........................................ |
15 |
Guard for the blade ............................................... |
15 |
STARTING AND STOPPING |
|
Before starting ...................................................... |
16 |
Starting ................................................................. |
16 |
Stopping ............................................................... |
16 |
MAINTENANCE |
|
General ................................................................. |
17 |
Cleaning ............................................................... |
17 |
Electrical Feed ...................................................... |
17 |
Replacing the carbon brushes .............................. |
17 |
Bevel gear ............................................................ |
18 |
Checking the drive shaft and flange washers ....... |
18 |
Checking water connection with flow limiter ......... |
18 |
Daily maintenance ................................................ |
18 |
TECHNICAL DATA |
|
Cutting equipment ................................................ |
20 |
Recommended cable dimensions ........................ |
20 |
EC-declaration of conformity ................................ |
21 |
English – 3
WHAT IS WHAT?
What is what on the power cutter - K3000?
1 |
Rear handle |
9 |
Rating plate |
2 |
Guard for the blade 14” |
10 |
Brush retainer |
3 |
Cutting blade |
11 |
Carbon brushes |
4 |
Locking the axle |
12 |
Guard for the blade 12” (Model version) |
5 |
Front handle |
13 |
Connection for vacuum cleaner |
6 |
Inspection covers |
14 |
Combination spanner |
7 |
Power switch lock |
15 |
Operator′s manual |
8 |
Switch |
|
|
4 – English
WHAT IS WHAT?
What is what on the power cutter - K3000 Wet?
1 |
Rear handle |
10 |
Water tap |
2 |
Guard for the blade |
11 |
Water connection with flow limiter |
3 |
Water kit |
12 |
Rating plate |
4 |
Cutting blade |
13 |
Brush retainer |
5 |
Locking the axle |
14 |
Carbon brushes |
6 |
Front handle |
15 |
Ground fault circuit interrupter (not for GB) |
7 |
Inspection covers |
16 |
Combination spanner |
8 |
Power switch lock |
17 |
Operator′s manual |
9 |
Switch |
|
|
English – 5
GENERAL SAFETY PRECAUTIONS
Steps before using a new power cutter
•Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.
•The machine is only designed for cutting hard materials, such as concrete, brick, masonry as well as cast iron and cement pipes.
•Let your Husqvarna dealer regularly check the power cutter and make essential adjustments and repairs.
WARNING! Under no circumstances
! should you modify the original design of the machine without approval from the manufacturer. Always use original spare parts. Unauthorized modifications and/or accessories may lead to serious injury or death to the user or others.
WARNING! Use of products which cut, ! grind, drill, sand or shape material can
generate dust and vapors which may contain harmful chemicals. Know the nature of the material being worked on and wear appropriate dust mask or respirator protection.
WARNING! A power cutter is a
! dangerous tool if used carelessly or incorrectly and can cause serious, even fatal injuries. It is extremely important that you read and understand the contents of this Operator’s Manual.
Husqvarna Construction Products has a policy of continuous product development. Husqvarna reserves the right to modify the design and appearance of products without prior notice and without further obligation introduce design modifications.
All information and all data in the Operator’s Manual were applicable at the time the Operator’s Manual was sent to print.
6 – English
Personal protective equipment
|
! |
WARNING! You must use approved |
|
personal protective equipment whenever |
|
|
|
|
|
|
you use the machine. Personal protective |
|
|
equipment cannot eliminate the risk of |
|
|
injury but it will reduce the degree of |
|
|
injury if an accident does happen. Ask |
|
|
your dealer for help in choosing the right |
|
|
equipment. |
• |
Protective helmet |
|
• |
Hearing protection |
|
• Protective goggles or a visor |
||
• |
Breathing mask |
|
• Heavy-duty, firm grip gloves.
•Tight-fitting, heavy-duty and comfortable clothing that permits full freedom of movement.
•Use leg-guards recommended for the material to be cut.
•Boots with steel toe-caps and non-slip sole.
•Always have a first aid kit nearby.
GENERAL SAFETY PRECAUTIONS
Machine′s safety equipment
This section describes the machine′s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the ”What is what?” section to locate where this equipment is positioned on your machine.
! |
WARNING! Never use a machine that has |
faulty safety equipment! Carry out the |
|
|
inspection, maintenance and service |
|
routines listed in this section. |
All servicing and repair work on the machine requires special training.This is especially true of the machine′s safety equipment. If your machine fails any of the checks described below you must contact your service agent. When you buy any of our products we guarantee the availability of professional repairs and service. If the retailer who sells your machine is not a servicing dealer, ask him for the address of your nearest service agent.
Switch
The power switch should be used to start and stop the machine.
Checking the power switch
•Start the machine, release the power switch and check that the engine and the cutting blade stop.
•A defective power switch should be replaced by an authorized service workshop.
Power switch lock
The power switch lock is designed to prevent accidental operation of the switch. When the lock (A) is pressed in the power switch (B) is released.
The power switch lock remains depressed as long as the power switch is depressed. When the grip on the handle is released both the power switch and power switch lock are reset. This movement is controlled by two independent return springs. This position results in the machine stopping and the power switch being locked.
Checking the power switch lock
•Make sure the power switch is locked when the power switch lock is in its original position.
•Press in the power switch lock and make sure it returns to its original position when you release it.
•Check that the power switch and power switch lock move freely and that the return springs work properly.
•Start the machine, release the power switch and check that the engine and the cutting blade stop.
Gradual start and overload protection
The machine is equipped with electronically controlled gradual start and overload protection.
The engine starts to pulsate if the machine is loaded above a specific level. If the load is reduced the engine reverts to its normal state and cutting can resume.
The electronics will cut the current after a set time if the machine continues to be run with a pulsating engine. The higher load the faster the shutoff.
The electronics cut the current immediately if the blade jams.
English – 7
Loading...