Epson PX710, TX710, PX720, TX720, PX730 Service Manual

SERVICE MANUAL

Color Inkjet Printer

Epson Artisan 810/

Epson Stylus Photo PX810FW/TX810FW/

Epson Artisan 835/

Epson Stylus Photo PX820FWD/TX820FWD/

Epson Artisan 837/

Epson Stylus Photo PX830FWD

Epson Artisan 710/

Epson Stylus Photo PX710W/TX710W/

Epson Artisan 725/

Epson Stylus Photo PX720WD/TX720WD

Epson Artisan 730/

Epson Stylus Photo PX730WD/TX730WD

Confidential

SEMF09-006

Notice:

All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION.

The contents of this manual are subject to change without notice.

All effort have been made to ensure the accuracy of the contents of this manual. However, should any errors be detected, SEIKO EPSON would greatly appreciate being informed of them.

The above not withstanding SEIKO EPSON CORPORATION can assume no responsibility for any errors in this manual or the consequences thereof.

EPSON is a registered trademark of SEIKO EPSON CORPORATION.

General Notice:	Other product names used herein are for identification purpose only and may be trademarks or registered trademarks of their
	respective owners. EPSON disclaims any and all rights in those marks.

Copyright © 2011 SEIKO EPSON CORPORATION.

I&I CS Quality Assurance Department

Confidential

	PRECAUTIONS
Precautionary notations throughout the text are categorized relative to 1) Personal injury and 2) damage to equipment.
DANGER	Signals a precaution which, if ignored, could result in serious or fatal personal injury. Great caution should be exercised in performing procedures preceded by
	DANGER Headings.
WARNING	Signals a precaution which, if ignored, could result in damage to equipment.

The precautionary measures itemized below should always be observed when performing repair/maintenance procedures.

DANGER

1.ALWAYS DISCONNECT THE PRODUCT FROM THE POWER SOURCE AND PERIPHERAL DEVICES PERFORMING ANY MAINTENANCE OR REPAIR PROCEDURES.

2.NO WORK SHOULD BE PERFORMED ON THE UNIT BY PERSONS UNFAMILIAR WITH BASIC SAFETY MEASURES AS DICTATED FOR ALL ELECTRONICS TECHNICIANS IN THEIR LINE OF WORK.

3.WHEN PERFORMING TESTING AS DICTATED WITHIN THIS MANUAL, DO NOT CONNECT THE UNIT TO A POWER SOURCE UNTIL INSTRUCTED TO DO SO. WHEN THE POWER SUPPLY CABLE MUST BE CONNECTED, USE EXTREME CAUTION IN WORKING ON POWER SUPPLY AND OTHER ELECTRONIC COMPONENTS.

4.WHEN DISASSEMBLING OR ASSEMBLING A PRODUCT, MAKE SURE TO WEAR GLOVES TO AVOID INJURIER FROM METAL PARTS WITH SHARP EDGES.

WARNING

1.REPAIRS ON EPSON PRODUCT SHOULD BE PERFORMED ONLY BY AN EPSON CERTIFIED REPAIR TECHNICIAN.

2.MAKE CERTAIN THAT THE SOURCE VOLTAGES IS THE SAME AS THE RATED VOLTAGE, LISTED ON THE SERIAL NUMBER/RATING PLATE. IF THE EPSON PRODUCT HAS A PRIMARY AC RATING DIFFERENT FROM AVAILABLE POWER SOURCE, DO NOT CONNECT IT TO THE POWER SOURCE.

3.ALWAYS VERIFY THAT THE EPSON PRODUCT HAS BEEN DISCONNECTED FROM THE POWER SOURCE BEFORE REMOVING OR REPLACING PRINTED CIRCUIT BOARDS AND/OR INDIVIDUAL CHIPS.

4.IN ORDER TO PROTECT SENSITIVE MICROPROCESSORS AND CIRCUITRY, USE STATIC DISCHARGE EQUIPMENT, SUCH AS ANTI-STATIC WRIST STRAPS, WHEN ACCESSING INTERNAL COMPONENTS.

5.REPLACE MALFUNCTIONING COMPONENTS ONLY WITH THOSE COMPONENTS BY THE MANUFACTURE; INTRODUCTION OF SECOND-SOURCE ICs OR OTHER NON-APPROVED COMPONENTS MAY DAMAGE THE PRODUCT AND VOID ANY APPLICABLE EPSON WARRANTY.

6.WHEN USING COMPRESSED AIR PRODUCTS; SUCH AS AIR DUSTER, FOR CLEANING DURING REPAIR AND MAINTENANCE, THE USE OF SUCH PRODUCTS CONTAINING FLAMMABLE GAS IS PROHIBITED.

Confidential

About This Manual

This manual describes basic functions, theory of electrical and mechanical operations, maintenance and repair procedures of the printer. The instructions and procedures included herein are intended for the experienced repair technicians, and attention should be given to the precautions on the preceding page.

Manual Configuration

This manual consists of six chapters and Appendix.

CHAPTER 1.PRODUCT DESCRIPTIONS

Provides a general overview and specifications of the product.

CHAPTER 2.OPERATING PRINCIPLES

Describes the theory of electrical and mechanical operations of the product.

CHAPTER 3.TROUBLESHOOTING

Describes the step-by-step procedures for the troubleshooting.

CHAPTER 4.DISASSEMBLY / ASSEMBLY

Describes the step-by-step procedures for disassembling and assembling the product.

CHAPTER 5.ADJUSTMENT

Provides Epson-approved methods for adjustment.

CHAPTER 6.MAINTENANCE

Provides preventive maintenance procedures and the lists of Epsonapproved lubricants and adhesives required for servicing the product.

CHAPTER 7.Provides the following additional information for reference:

•Exploded Diagram

•Parts List

CHAPTER 8.Artisan 835/725/PX820FWD/TX820FWD/PX720WD/TX720WD

Provides particular information on the following models:

•Epson Artisan 835/Epson Stylus Photo PX820FWD/TX820FWD

•Epson Artisan 725/Epson Stylus Photo PX720WD/TX720WD

CHAPTER 9.Artisan 837/730/PX830FWD/PX730WD/TX730WD

Provides particular information on the following models:

•Epson Artisan 837/Epson Stylus Photo PX830FWD

•Epson Artisan 730/Epson Stylus Photo PX730WD/TX730WD

Symbols Used in this Manual

Various symbols are used throughout this manual either to provide additional information on a specific topic or to warn of possible danger present during a procedure or an action. Be aware of all symbols when they are used, and always read NOTE, CAUTION, or WARNING messages.

ADJUSTMENT	Indicates an operating or maintenance procedure, practice or condition
REQUIRED	that is necessary to keep the product’s quality.

Indicates an operating or maintenance procedure, practice, or condition CAUTION that, if not strictly observed, could result in damage to, or destruction of,

equipment.

CHECK

May indicate an operating or maintenance procedure, practice or

POINT condition that is necessary to accomplish a task efficiently. It may also provide additional information that is related to a specific subject, or

comment on the results achieved through a previous action.

Indicates an operating or maintenance procedure, practice or condition WARNING that, if not strictly observed, could result in injury or loss of life.

Indicates that a particular task must be carried out according to a certain standard after disassembly and before re-assembly, otherwise the quality of the components in question may be adversely affected.

Confidential

		Revision Status
Revision	Date of Issue	Description
A	July 29, 2009	First Release
B	August 7, 2009	Revised Contents
		Chapter 4
		Caution of “ Assembling the Printhead (p.134)” has been added.
		Chapter 5
		Made change in “5.1.1 Servicing Adjustment Item List (p.202)”.
		Made change in “5.3.1 PG Adjustment/PG Inspection (p.226)”.
C	January 7,2010	Revised Contents
		Chapter 4
		Made change in “ Assembling the Printhead (p.134)”.
D	June 18, 2010	Revised Contents
		All chapters
		Description about Epson Artisan 835/725/Epson Stylus Photo PX820FWD/TX820FWD/PX720WD/TX720WD has
		been added.
		Chapter 1
		Checkpoint has been added in “1.1 Features (p.15)”.
		Chapter 2
		Checkpoint has been added in “2.1 Overview (p.49)”.
		Made correction in “2.2 Power-On Sequence (p.53)”.
		Chapter 3
		Checkpoint has been added in “3.1 Overview (p.61)”
		Note has been added in “3-5 Check point for Fatal error according to each phenomenon (Printer Mechanism)
		(p.65)”.
		Chapter 4
		Checkpoint has been added in “4.1 Overview (p.101)”
		Tool information for Epson Artisan 835/Epson Stylus Photo PX820FWD/TX820FWD has been added in “4.1.2
		Tools (p.102)”.
		Checkpoint has been added in “4.1.4 Additional Procedure/Procedural Differences (p.104)”.
		Made change for checkpoint in “4.2 Disassembly Procedures (p.106)”.
		Checkpoint has been added in “4.2.3.1 ADF Unit (p.110)”.
		Checkpoint has been added in “4.2.3.5 Upper Housing (p.115)”.

Confidential

Revision	Date of Issue	Description
D	June 18, 2010	Chapter 4
		Checkpoint has been added in “4.2.4.1 Panel Unit (p.124)”.
		Made change for “adjustment required” and made correction in “4.2.4.2 Main Board / Grounding Plate M/B (p.126)”.
		Checkpoint has been added in “4.2.5.2 CR Scale (p.139)”.
		Checkpoint has been added in “4.2.5.7 Ink System (p.146)”.
		Made change for reassembly in “4.2.5.11 Waste Ink Tray Assy (p.153)”.
		Made correction for reassembly in “4.2.7.2 ADF Cover Assy/ADF Cover L (p.165)”.
		Reassembly has been added in “4.2.7.7 ADF Document Support Assy (p.170)”.
		Made change for checkpoint in “4.3.1.3 Upper Housing (p.179)”.
		Made change for checkpoint in “4.3.2.1 Panel Unit (p.185)”.
		Made change for “adjustment required” in “4.3.2.2 Main Board/Grounding Plate M/B (p.187)”.
		Chapter 5
		Made change in “5.1 Adjustment Items and Overview (p.202)”.
		Made change for caution in “5.2.6 MAC Address Setting (p.214)”.
		Made change for caution and checkpoint, and made correction in “5.2.8 Case Open Sensor Check (p.217)”.
		Made change for checkpoint in “5.2.9 AID inspection (p.220)”.
		Made change for “Specified Scanner for BRS/PFP Adjustment” in “5.2.10 Banding Reduction System (BRS)
		Adjustment / Paper Feed Amount Profile (PFP) Correction (p.221)”.
		Made correction for checkpoint in “5.3.1.1 PG Adjustment (p.226)”.
		Made correction for checkpoint in “5.3.1.2 PG Inspection (p.230)”.
		Made change for checkpoint in “5.4.2 AID SHK Error Reset (p.236)”.
		Chapter 6
		Checkpoint has been added in “6.1 Overview (p.239)”.
		Chapter 7
		Checkpoint has been added in “7.1 Connector Summary (p.247)”.
		Chapter 8
		Information for Epson Artisan 835/725/Epson Stylus Photo PX820FWD/TX820FWD/PX720WD/TX720WD has
		been added.
E	June 13, 2011	Revised Contents
		All chapters
		Description about Epson Artisan 837/730/Epson Stylus Photo PX830FWD/PX730WD/TX730WD has been added.
		Chapter 1
		Made change for checkpoint in “1.1 Features (p.15)”.
		Chapter 2
		Made change for checkpoint in “2.1 Overview (p.49)”.

Confidential

Revision	Date of Issue	Description
E	June 13, 2011	Chapter 3
		Made change for checkpoint in “3.1 Overview (p.61)”
		Made change for and note has been changed in “3-4 Error Indications and Fault Occurrence Causes (p.63)”.
		Note has been changed in “Table 3-5 Check point for Fatal error according to each phenomenon (Printer
		Mechanism)” (p.65).
		Made change for checkpoint in “3.7 FAX Troubleshooting (p.88)”
		Description about Epson Artisan 837/730/Epson Stylus Photo PX830FWD/PX730WD/TX730WD has been added
		in “3.8 Fax Function/External Connection Function Check (p.94)”.
		Chapter 4
		Made change for checkpoint in “4.1 Overview (p.101)”
		Note has been changed in “Table 4-1 Tools” (p.102).
		Note has been changed in “Table 4-2 Work Completion Check” (p.102).
		Made change for checkpoint in “4.1.4 Additional Procedure/Procedural Differences (p.104)”
		Made change for checkpoint in “4.2 Disassembly Procedures (p.106)”
		Made change for checkpoint in “4.2.3.1 ADF Unit (p.110)”.
		Made change for checkpoint and description in “4.2.3.2 Scanner Unit (p.111)”.
		Made change in “4.2.3.3 Hinge (p.113)”.
		Made change for checkpoint in “4.2.3.4 Upper Left Housing / Panel Lock Button (p.114)”.
		Made change for checkpoint and description in “4.2.3.5 Upper Housing (p.115)”.
		Made change for checkpoint and description in “4.2.3.6 Rear Left Housing (p.117)”.
		Made change for checkpoint and description in “4.2.3.7 Left Housing / Decoration Belt L (p.117)”.
		Made change in “4.2.3.8 Stacker Assy (p.118)”.
		Made change for checkpoint and description in “4.2.3.10 Rear Right FAX Housing (p.120)”.
		Made change for checkpoint and description in “4.2.3.11 Right Housing / Card Cover (p.121)”.
		Checkpoint has been added in “4.2.3.12 Cassette Unit/EJ Cover Assy (p.122)”.
		Made change for checkpoint in “4.2.4.1 Panel Unit (p.124)”.
		Made change for checkpoint and description in “4.2.4.2 Main Board / Grounding Plate M/B (p.126)”.
		Made change in “4.2.4.3 Power Supply Unit (p.129)”.
		Made change in “4.2.4.4 Wireless LAN Board (p.130)”.
		Made change for checkpoint and description in “4.2.4.5 Card Slot Assy (p.131)”.
		Made change in “4.2.5.1 Printhead (p.132)”.
		Made change for checkpoint and description in “4.2.5.2 CR Scale (p.139)”.
		Made change in “4.2.5.3 PF Encoder (p.140)”.

Confidential

Revision	Date of Issue	Description
E	June 13, 2011	Made change in “4.2.5.4 Decompression Pump Unit (p.141)”.
		Made change for checkpoint and description in “4.2.5.5 CSIC Assy (p.142)”.
		Made change in “4.2.5.6 Ink Supply IC Holder Assy (p.143)”.
		Made change for checkpoint and description in “4.2.5.7 Ink System (p.146)”.
		Made change in “4.2.5.8 Lower ASF Paper Guide Assy (p.148)”.
		Made change in “4.2.5.9 CDR Tray Assy (p.151)”.
		Made correction for reassembly in “4.2.5.11 Waste Ink Tray Assy (p.153)”.
		Made change for checkpoint in “4.2.6 Disassembling Scanner Unit (p.157)”.
		Made change for checkpoint in “4.2.6.1 Scanner Upper Housing (p.157)”.
		Made change in “4.2.6.2 Scanner Motor Unit (p.158)”.
		Made change in “4.2.6.3 Scanner Carriage Unit (p.160)”.
		Made change for description and reassembly in “4.2.6.4 Scanner CR Encoder Board (p.162)”.
		Checkpoint has been added in “4.2.6.5 Cover Open Sensor (p.163)”.
		Made change for checkpoint in “4.3.1.1 Scanner Unit (p.176)”.
		Made change for checkpoint in “4.3.1.2 Upper Left Housing (p.178)”.
		Made change for checkpoint in “4.3.1.3 Upper Housing (p.179)”.
		Made change for checkpoint in “4.3.1.4 Rear Left Housing (p.181)”.
		Made change for checkpoint in “4.3.1.5 Left Housing/Decoration Belt L (p.182)”.
		Made change for checkpoint in “4.3.1.6 Rear Right Housing (p.183)”.
		Made change for checkpoint in “4.3.1.7 Right Housing/Card Cover (p.184)”.
		Made change for checkpoint in “4.3.2.1 Panel Unit (p.185)”.
		Made change for checkpoint and description in “4.3.2.2 Main Board/Grounding Plate M/B (p.187)”.
		Made change for checkpoint in “4.3.2.3 Card Slot Assy (p.190)”.
		Made change for checkpoint in “4.3.3 Disassembling the Scanner Unit (p.191)”.
		Made change for checkpoint in “4.3.3.2 Scanner Upper Housing (p.191)”.
		Checkpoint has been added and made change in “4.4 Routing FFC/cables (p.193)”.
		Chapter 5
		Made change for checkpoint and description in “5.1.1 Servicing Adjustment Item List (p.202)”
		Checkpoint has been added and made change for caution in “5.2.8 Case Open Sensor Check (p.217)”.
		Made change for checkpoint in “5.2.9 AID inspection (p.220)”
		Made change in “5.2.10 Banding Reduction System (BRS) Adjustment / Paper Feed Amount Profile (PFP)
		Correction (p.221)”.
		Made change for checkpoint in “5.3 Adjustment without Using Adjustment Program (p.226)”

Confidential

Revision	Date of Issue	Description
E	June 13, 2011	Made change in “5.3.4 Touch Panel Adjustment (Artisan 810/835/837/PX810FW/TX810FW/PX820FWD/
		TX820FWD/PX830FWD only) (p.233)”.
		Chapter 6
		Made change for checkpoint in “6.1 Overview (p.239)”.
		Made change in “6.1.3 Lubrication (p.240)”.
		Chapter 7
		Made change for checkpoint in “7.1 Connector Summary (p.247)”.
		Chapter 8
		Made change for checkpoint and description in “8.1 Overview (p.251)”.
		Made change in “8.2 Operation principles (p.252)”.
		Made change for checkpoint in “8.3.2.1 ADF Unit (p.261)”.
		Made change for checkpoint and description in “8.3.2.4 CR Scale (p.267)”.
		Made change for checkpoint and description in “8.3.2.5 Ink System (p.269)”.
		Made change for checkpoint in “8.5.2 Service Maintenance (p.278)”.
		Chapter 9
		Information for Epson Artisan 837/730/Epson Stylus Photo PX830FWD/PX730WD/TX730WD has been added.

Confidential

Epson Artisan 810/835/837/710/725/730/Epson Stylus Photo PX810FW/TX810FW/PX820FWD/TX820FWD/PX830FWD/PX710W/TX710W/PX720WD/TX720WD/PX730WD/TX730WD

Revision E

Contents

Chapter 1 PRODUCT DESCRIPTION
1.1	Features................................................................................................................	15
1.2	Printing Specifications.........................................................................................	16
	1.2.1 Basic Specifications....................................................................................	16
	1.2.2 Ink Cartridge...............................................................................................	16
	1.2.3 Print Mode ..................................................................................................	17
	1.2.4 Supported Paper..........................................................................................	19
	1.2.5 Printing Area...............................................................................................	22
1.3	Scanner Specifications.........................................................................................	22
	1.3.1 Scanning Range ..........................................................................................	23
1.4	General Specifications.........................................................................................	23
	1.4.1 Electrical Specifications .............................................................................	23
	1.4.2 Safety Approvals (Safety standards/EMI) ..................................................	24
	1.4.3 Acoustic Noise............................................................................................	24
	1.4.4 Durability (TBD) ........................................................................................	24
	1.4.5 Environmental Conditions ..........................................................................	24
1.5	Interface...............................................................................................................	25
	1.5.1 USB Interface .............................................................................................	25
	1.5.2 FAX Interface (Epson Artisan 810/Epson Stylus Photo PX810FW/TX810FW only) ...	25
	1.5.3 Network Interface .......................................................................................	25
	1.5.4 Memory Card Slots.....................................................................................	27
1.6	Control Panel .......................................................................................................	28
	1.6.1 Operation Buttons & LEDs ........................................................................	28
	1.6.2 Control Panel Functions in Each Mode ......................................................	29
	1.6.2.1 Control Panel Functions ......................................................................	29
1.7	Specification for Each Function ..........................................................................	31
	1.7.1 Stand-alone Copy Function (Copy Mode)..................................................	31
	1.7.1.1 Supported Paper and Copy Mode........................................................	31
	1.7.1.2 Stand-alone Copy Menu......................................................................	32
	1.7.1.3 Copy Speed (TBD)..............................................................................	32
	1.7.1.4 Relation Between Original and Copy..................................................	33

1.7.2 Memory Card Direct Print Function (Photos Mode)..................................	33
1.7.2.1 Supported Paper and Print Mode ........................................................	33
1.7.2.2 Supported File Type and Media Type.................................................	34
1.7.2.3 Automatic Detection of Images in Memory Card...............................	34
1.7.2.4 Specifications for Handling Image Data .............................................	34
1.7.2.5 Memory Card Direct Print Menu ........................................................	35
1.7.2.6 Makes Prints from Index Sheet Function............................................	36
1.7.2.7 Print Layout.........................................................................................	37
1.7.3 Camera Direct Print Function (PictBridge) ................................................	40
1.7.3.1 Available DSC.....................................................................................	40
1.7.3.2 Print Settings Available from DSC .....................................................	40
1.7.3.3 General Operation Procedure ..............................................................	41
1.7.3.4 Operations when a DSC is connected .................................................	41
1.7.4 Various Settings (Setup Mode)...................................................................	42
1.7.5 FAX Function (FAX Mode)
(Epson Artisan 810/Epson Stylus Photo PX810FW/TX810FW only) .......	44
1.7.5.1 Basic Specifications ............................................................................	44
1.7.5.2 Supported Functions............................................................................	44
1.7.6 Other Functions ..........................................................................................	47
1.7.6.1 Scan Mode...........................................................................................	47
1.7.6.2 Backup Data ........................................................................................	47
1.7.6.3 Print Ruled Papers...............................................................................	47
1.7.6.4 Coloring Book .....................................................................................	47
Chapter 2 OPERATING PRINCIPLES
2.1 Overview .............................................................................................................	49
2.1.1 Printer Mechanism......................................................................................	49
2.1.2 Printhead.....................................................................................................	49
2.1.3 Motors & Sensors .......................................................................................	50
2.1.4 PG setting ...................................................................................................	52
2.2 Power-On Sequence ............................................................................................	53
2.2.1 Simple Reset Sequence...............................................................................	54
2.2.2 All Reset Sequence.....................................................................................	56
2.3 Printer Initialization.............................................................................................	59

10

Confidential

Epson Artisan 810/835/837/710/725/730/Epson Stylus Photo PX810FW/TX810FW/PX820FWD/TX820FWD/PX830FWD/PX710W/TX710W/PX720WD/TX720WD/PX730WD/TX730WD

Revision E

Chapter 3 TROUBLESHOOTING
3.1	Overview .............................................................................................................	61
	3.1.1 Specified Tools ...........................................................................................	61
	3.1.2 Preliminary Checks.....................................................................................	61
3.2	Troubleshooting...................................................................................................	62
	3.2.1 Motor and Sensor Troubleshooting ............................................................	62
3.3	Troubleshooting by Error Message .....................................................................	63
	3.3.1 Error Message List......................................................................................	63
	3.3.2 Troubleshooting by Error Message ............................................................	65
3.4	Troubleshooting without Error Message .............................................................	77
	3.4.1 Troubleshooting Printer Mechanism Problems ..........................................	77
	3.4.2 Troubleshooting Electrical Problems .........................................................	83
	3.4.3 Troubleshooting I/F-related Problems........................................................	83
3.5	Troubleshooting Duplex Unit Problems..............................................................	85
3.6	Network Troubleshooting....................................................................................	86
3.7	FAX Troubleshooting..........................................................................................	88
	3.7.1 FAX Log.....................................................................................................	88
	3.7.2 Error Code/Superficial Phenomenon-Based Troubleshooting ...................	92
3.8	Fax Function/External Connection Function Check ...........................................	94
	3.8.1 Outline ........................................................................................................	94
	3.8.2 Fax Function and External Connection Function Check............................	94
	3.8.2.1 Fax Function Check by [Method A] and External Connection Function Check ...	94
	3.8.2.2 Fax Function Check by [Method B] and External Connection Function Check ...	98
	3.8.2.3 Fax Function Check by [Method C] and External Connection Function Check ...	99
Chapter 4 DISASSEMBLY/ASSEMBLY
4.1	Overview ...........................................................................................................	101
	4.1.1 Precautions................................................................................................	101
	4.1.2 Tools .........................................................................................................	102
	4.1.3 Work Completion Check ..........................................................................	102
	4.1.4 Additional Procedure/Procedural Differences..........................................	104
4.2	Disassembly Procedures....................................................................................	106
	4.2.1 Parts transferred from the old printer when replacing the Printer Mechanism 108
	4.2.2 Replacing the Head Supply Assy .............................................................	109

4.2.3 Removing the Housing .............................................................................	110
4.2.3.1 ADF Unit...........................................................................................	110
4.2.3.2 Scanner Unit......................................................................................	111
4.2.3.3 Hinge .................................................................................................	113
4.2.3.4 Upper Left Housing / Panel Lock Button..........................................	114
4.2.3.5 Upper Housing ..................................................................................	115
4.2.3.6 Rear Left Housing .............................................................................	117
4.2.3.7 Left Housing / Decoration Belt L......................................................	117
4.2.3.8 Stacker Assy......................................................................................	118
4.2.3.9 Rear ASF Paper Guide Cover ...........................................................	119
4.2.3.10 Rear Right FAX Housing................................................................	120
4.2.3.11 Right Housing / Card Cover............................................................	121
4.2.3.12 Cassette Unit/EJ Cover Assy...........................................................	122
4.2.3.13 Paper Guide Top Assy.....................................................................	123
4.2.4 Removing the Circuit Board.....................................................................	124
4.2.4.1 Panel Unit..........................................................................................	124
4.2.4.2 Main Board / Grounding Plate M/B..................................................	126
4.2.4.3 Power Supply Unit ............................................................................	129
4.2.4.4 Wireless LAN Board.........................................................................	130
4.2.4.5 Card Slot Assy...................................................................................	131
4.2.5 Disassembling the Printer Mechanism .....................................................	132
4.2.5.1 Printhead............................................................................................	132
4.2.5.2 CR Scale............................................................................................	139
4.2.5.3 PF Encoder ........................................................................................	140
4.2.5.4 Decompression Pump Unit................................................................	141
4.2.5.5 CSIC Assy .........................................................................................	142
4.2.5.6 Ink Supply IC Holder Assy ...............................................................	143
4.2.5.7 Ink System.........................................................................................	146
4.2.5.8 Lower ASF Paper Guide Assy ..........................................................	148
4.2.5.9 CDR Tray Assy .................................................................................	151
4.2.5.10 Pick-up Roller .................................................................................	152
4.2.5.11 Waste Ink Tray Assy .......................................................................	153
4.2.5.12 Lower Paper Guide Waste Ink Pad Assy ........................................	156
4.2.6 Disassembling Scanner Unit.....................................................................	157
4.2.6.1 Scanner Upper Housing ....................................................................	157
4.2.6.2 Scanner Motor Unit...........................................................................	158
4.2.6.3 Scanner Carriage Unit .......................................................................	160
4.2.6.4 Scanner CR Encoder Board...............................................................	162
4.2.6.5 Cover Open Sensor............................................................................	163

11

Confidential

Epson Artisan 810/835/837/710/725/730/Epson Stylus Photo PX810FW/TX810FW/PX820FWD/TX820FWD/PX830FWD/PX710W/TX710W/PX720WD/TX720WD/PX730WD/TX730WD

Revision E

4.2.7 Disassembly of the ADF Unit...................................................................	165
4.2.7.1 ADF Hinge ........................................................................................	165
4.2.7.2 ADF Cover Assy/ADF Cover L........................................................	165
4.2.7.3 ADF LD Frame Assy ........................................................................	167
4.2.7.4 ADF Right Cover/ADF Rear Cover..................................................	167
4.2.7.5 ADF Cover Stacker/ADF Document Support Cover ........................	169
4.2.7.6 ADF Front Cover...............................................................................	170
4.2.7.7 ADF Document Support Assy...........................................................	170
4.2.7.8 ADF Frame Unit................................................................................	171
4.2.7.9 ADF Motor Unit................................................................................	172
4.2.7.10 ADF PF Roller.................................................................................	175
4.3 Disassembly/reassembly procedures specific to Artisan 710/PX710W/TX710W..	176
4.3.1 Removing the Housing .............................................................................	176
4.3.1.1 Scanner Unit ......................................................................................	176
4.3.1.2 Upper Left Housing...........................................................................	178
4.3.1.3 Upper Housing ..................................................................................	179
4.3.1.4 Rear Left Housing .............................................................................	181
4.3.1.5 Left Housing/Decoration Belt L........................................................	182
4.3.1.6 Rear Right Housing ...........................................................................	183
4.3.1.7 Right Housing/Card Cover................................................................	184
4.3.2 Removing the Circuit Board.....................................................................	185
4.3.2.1 Panel Unit ..........................................................................................	185
4.3.2.2 Main Board/Grounding Plate M/B ....................................................	187
4.3.2.3 Card Slot Assy...................................................................................	190
4.3.3 Disassembling the Scanner Unit...............................................................	191
4.3.3.1 Document Cover................................................................................	191
4.3.3.2 Scanner Upper Housing.....................................................................	191
4.4 Routing FFC/cables ...........................................................................................	193
Chapter 5 ADJUSTMENT
5.1 Adjustment Items and Overview .......................................................................	202
5.1.1 Servicing Adjustment Item List................................................................	202
5.1.2 Required Adjustments ..............................................................................	208
5.2 Adjustment Using Adjustment Program ...........................................................	210
5.2.1 Top Margin Adjustment ...........................................................................	210
5.2.2 Bi-D Adjustment.......................................................................................	210
5.2.3 PW Adjustment/First Dot Position Adjustment .......................................	211
5.2.4 Head Angular Adjustment ........................................................................	212
5.2.5 PF Adjustment ..........................................................................................	213
5.2.6 MAC Address Setting...............................................................................	214
5.2.7 PG Offset Value Adjustment ....................................................................	216

	5.2.8 Case Open Sensor Check..........................................................................	217
	5.2.9 AID inspection..........................................................................................	220
	5.2.10 Banding Reduction System (BRS) Adjustment /
	Paper Feed Amount Profile (PFP) Correction...........................................	221
	5.2.10.1 BRS (Banding Reduction System) Adjustment ..............................	223
	5.2.10.2 PFP Adjustment...............................................................................	224
5.3	Adjustment without Using Adjustment Program ..............................................	226
	5.3.1 PG Adjustment/PG Inspection..................................................................	226
	5.3.1.1 PG Adjustment ..................................................................................	226
	5.3.1.2 PG Inspection ....................................................................................	230
	5.3.2 CR Timing Belt Tension Inspection.........................................................	231
	5.3.3 PF Timing Belt Tension Inspection..........................................................	232
	5.3.4 Touch Panel Adjustment (Artisan 810/835/837/PX810FW/TX810FW/
	PX820FWD/TX820FWD/PX830FWD only) ...........................................	233
5.4	Other functions ..................................................................................................	235
	5.4.1 I/S Decompress.........................................................................................	235
	5.4.2 AID SHK Error Reset...............................................................................	236
Chapter 6 MAINTENANCE
6.1	Overview ...........................................................................................................	239
	6.1.1 Cleaning....................................................................................................	239
	6.1.2 Service Maintenance.................................................................................	239
	6.1.2.1 Printhead cleaning .............................................................................	239
	6.1.2.2 Service Call .......................................................................................	240
	6.1.3 Lubrication................................................................................................	240
Chapter 7 APPENDIX
7.1	Connector Summary..........................................................................................	247
7.2	Exploded Diagram / Parts List ..........................................................................	249
Chapter 8 Artisan 835/725/PX820FWD/TX820FWD/PX720WD/TX720WD
8.1	Overview ...........................................................................................................	251
8.2	Operation principles ..........................................................................................	252
	8.2.1 Power-On Sequence .................................................................................	252
	8.2.1.1 Simple Reset Sequence .....................................................................	252
	8.2.1.2 All Reset Sequence............................................................................	254

12

Confidential

Epson Artisan 810/835/837/710/725/730/Epson Stylus Photo PX810FW/TX810FW/PX820FWD/TX820FWD/PX830FWD/PX710W/TX710W/PX720WD/TX720WD/PX730WD/TX730WD

Revision E

8.3	Disassembly/assembly.......................................................................................	257
	8.3.1 Procedural Differences between the Models ............................................	257
	8.3.2 Disassembly Procedures ...........................................................................	259
	8.3.2.1 ADF Unit...........................................................................................	261
	8.3.2.2 Upper Housing ..................................................................................	263
	8.3.2.3 Panel Unit ..........................................................................................	265
	8.3.2.4 CR Scale ............................................................................................	267
	8.3.2.5 Ink System.........................................................................................	269
8.4	Adjustment ........................................................................................................	271
	8.4.1 Overview...................................................................................................	271
	8.4.2 Required Adjustments (Artisan 835/725/PX820FWD/TX820FWD/
	PX720WD/TX720WD).............................................................................	272
	8.4.3 Special Inspection Mode...........................................................................	275
	8.4.4 Touch Panel Calibration ...........................................................................	276
	8.4.5 Touch Panel Operation Check ..................................................................	276
8.5	Maintenance ......................................................................................................	278
	8.5.1 Cleaning....................................................................................................	278
	8.5.2 Service Maintenance.................................................................................	278
	8.5.2.1 Printhead cleaning .............................................................................	278
8.6	Connector Summary..........................................................................................	279
Chapter 9 Artisan 837/730/PX830FWD/PX730WD/TX730WD
9.1	Overview ...........................................................................................................	281
9.2	Operation principles ..........................................................................................	282
	9.2.1 Motors & Sensors .....................................................................................	282
9.3	Troubleshooting.................................................................................................	284

9.4 Disassembly/assembly.......................................................................................	285
9.4.1 Procedural Differences between the Models ............................................	285
9.4.2 Disassembly Procedures ...........................................................................	287
9.4.2.1 Decoration Plate Left Upper Sub ......................................................	290
9.4.2.2 Upper Housing ..................................................................................	291
9.4.2.3 Decoration Plate Left Upper .............................................................	293
9.4.2.4 Rear Left Housing .............................................................................	294
9.4.2.5 Left Housing......................................................................................	295
9.4.2.6 Rear Right FAX Housing..................................................................	296
9.4.2.7 Right Housing/Housing Front Right .................................................	297
9.4.2.8 Front Cover .......................................................................................	298
9.4.2.9 Housing Front Left ............................................................................	298
9.4.2.10 Panel Unit........................................................................................	299
9.4.2.11 Relay Board.....................................................................................	301
9.4.2.12 Document Cover Open Sensor........................................................	301
9.4.2.13 Scanner Open Sensor ......................................................................	303
9.4.2.14 Scanner Upper Housing ..................................................................	304
9.4.2.15 Scanner Decoration Plate Front.......................................................	304
9.4.2.16 Decoration Plate Left Upper/Decoration Plate Left Upper Sub......	305
9.4.2.17 Upper Housing ................................................................................	306
9.4.2.18 Panel Unit........................................................................................	308
9.4.2.19 Rear Left Housing ...........................................................................	310
9.4.2.20 Rear Right Housing.........................................................................	311
9.4.2.21 Right Housing / Housing Front Right .............................................	312
9.4.2.22 Scanner Open Sensor ......................................................................	313
9.4.2.23 Scanner Upper Housing ..................................................................	314
9.4.2.24 Scanner Decoration Plate Front.......................................................	315
9.4.3 Routing FFC/cables ..................................................................................	316
9.5 Adjustment ........................................................................................................	318
9.5.1 Overview ..................................................................................................	318
9.5.2 Required Adjustments (Artisan 837/730/PX830FWD/PX730WD/TX730WD) 318
9.5.3 Special Inspection Mode ..........................................................................	321
9.5.4 Tools Used for the Case Open Sensor Check...........................................	322
9.5.5 Scanners for Banding Reduction System (BRS) Adjustment /
Paper Feed Amount Profile (PFP) Correction...........................................	323
9.6 Connector Summary..........................................................................................	324

13

Confidential

C H A P T E R

1

PRODUCT DESCRIPTION

Confidential

Epson Artisan 810/835/837/710/725/730/Epson Stylus Photo PX810FW/TX810FW/PX820FWD/TX820FWD/PX830FWD/PX710W/TX710W/PX720WD/TX720WD/PX730WD/TX730WD

Revision E

1.1 Features

CHECK	Description in this chapter is applied to Epson Artisan 810/710/
POINT	Epson Stylus Photo PX810FW/TX810FW/PX710W/TX710W.
	For information on Epson Artisan 835/837/725/730/Epson Stylus
	Photo PX820FWD/TX820FWD/PX830FWD/PX720WD/TX720WD/
	PX730WD/TX730WD, see below.

Epson Artisan 835/725/Epson Stylus Photo PX820FWD/

TX820FWD/PX720WD/TX720WD:

Chapter 8 (p.250)

Epson Artisan 837/730/Epson Stylus Photo PX830FWD/

PX730WD/TX730WD:

Chapter 9 (p.280)

Epson Artisan 810/Epson Stylus Photo PX810FW/TX810FW/Epson Artisan 710/ Epson Stylus Photo PX710W/TX710W are color inkjet printers that have 4 in 1 functions (Printer for PC, Scanner for PC, Standalone copy, Memory card printing).

Common features

Printer

•Printing from a computer or directly printing from a memory card

•Auto duplex printing using Duplex Printing Unit (option for some destinations)

•Built-in CD/DVD tray

•Front double paper feeding function using a double-deck cassette

•Auto nozzle check (printhead cleaning) using AID

•Maximum print resolution: 5760 (H) x 1440 (V) dpi

•F6 Turbo II print head achieves higher print speed than ever (Black: 180 nozzles x 1, Color: 180 nozzles x 5 per color)

•Six independent ink cartridges is installed (Dye inks)

•Borderless printing on specified EPSON brand paper is available

Scanner

•Scanning from a computer

•Offers a function that directly stores a scan data to a memory card

Copy

•High quality copy using the printing and scanning functions. Offers seven preset copy layouts

USB interfaces

•Enables to print images in an external storage device

•Backup copy of a memory card can be made on an external media

•Offers camera direct print (PictBridge)

Network

•Available for printing, scanning, and memory card access via wired/wireless network

Bluetooth

•Mounting the optional Bluetooth unit offers wireless communication with an external device

Features unique to Epson Artisan 810/Epson Stylus Photo PX810FW/ TX810FW

FAX

•Sending/receiving fax

ADF

•Continuous scanning using an ADF

Differences between the models

Epson Artisan 810/Epson Stylus Photo PX810FW/TX810FW/Epson Artisan 710/ Epson Stylus Photo PX710W/TX710W are different on ADF, FAX and the Panel specifications as shown below.

		Epson Artisan 810/Epson	Epson Artisan 710/Epson
	Item	Stylus Photo PX810FW/	Stylus Photo PX710W/
		TX810FW	TX710W
	LCD display size	3.5 inch	2.5 inch
	Panel operation	Touch panel	Button
	Scanner resolution	4,800 dpi x 4,800 dpi	2,400 dpi x 4,800 dpi
	(Main scan x Sub scan)	(1,200 dpi x 600 dpi)*
	ADF	Equipped	---
	FAX function	Supported	---

Note* : When scanning using ADF

Dimensions

Epson Artisan 810/Epson Stylus Photo PX810FW/TX810FW

• Dimensions*1:	466 mm (W) x 385 mm (D) x 198 mm (H)
• Weight*2:	10.5 kg

Epson Artisan 710/Epson Stylus Photo PX710W/TX710W

• Dimensions*1:	466 mm (W) x 385 mm (D) x 150 mm (H)
• Weight*2:	9.0 kg

Note *1: Paper support and stacker are closed. Rubber feet are included. *2: Except ink cartridges and cables such as the AC cable, etc.

PRODUCT DESCRIPTION

Features

15

Confidential

Epson Artisan 810/835/837/710/725/730/Epson Stylus Photo PX810FW/TX810FW/PX820FWD/TX820FWD/PX830FWD/PX710W/TX710W/PX720WD/TX720WD/PX730WD/TX730WD

Revision E

	1.2	Printing Specifications
	1.2.1	Basic Specifications
			Table 1-1. Printer Specifications
		Item		Specification
	Print method		On-demand ink jet
			Black: 180 nozzles x 1
	Nozzle configuration		Color: 180 nozzles x 5
			(Light Cyan, Magenta, Yellow, Cyan, Light Magenta)
	Print direction		Bi-directional minimum distance printing, Unidirectional printing
			Horizontal x Vertical (dpi)
	Print resolution		• 360 x 180	• 720 x 720
			• 360 x 360	• 5760 x 1440
			• 720 x 360
			• ESC/P Raster command
	Control code		• ESC/P-R (RGB) command
			• EPSON Remote command
	Input buffer size		64 Kbytes
	Paper feed method		Friction feed, using the ASF (Auto Sheet Feeder)
	Paper path		Front feed, front out
	Paper feed rates		86 msec. (at 25.4 mm feed)
	PF interval		Programmable in 0.01764 mm (1/1440 inch) steps

1.2.2 Ink Cartridge

The product numbers of the EPSON ink cartridges for this printer are shown below.

Table 1-2. Product No. of Ink Cartridges

	Color	EAI		CISMEA/Asia	Euro
	Black	T0981 (S)		T0811N (S)	T0791	(S)
				T0821N (2S)	T0801	(2S)
	Cyan	T0982	(S)	T0812N (S)	T0792	(S)
		T0992	(2S)	T0822N (2S)	T0802	(2S)
	Magenta	T0983	(S)	T0813N (S)	T0793	(S)
		T0993	(2S)	T0823N (2S)	T0803	(2S)
	Yellow	T0984	(S)	T0814N (S)	T0794	(S)
		T0994	(2S)	T0824N (2S)	T0804	(2S)
	Light Cyan	T0985	(S)	T0815N (S)	T0795	(S)
		T0995	(2S)	T0825N (2S)	T0805	(2S)
	Light Magenta	T0986	(S)	T0816N (S)	T0796	(S)
		T0996	(2S)	T0826N (2S)	T0806	(2S)

Shelf life

Two years from production date (if unopened), six months after opening package.

Storage Temperature

Table 1-3. Storage Temperature

	Situation	Storage Temperature	Limit
	When stored in individual boxes	-20 oC to 40 oC
		(-4oF to 104oF)
			1 month max. at 40 oC (104oF)
	When installed in main unit	-20 oC to 40 oC
		(-4oF to 104oF)

Dimension

12.7 mm (W) x 68 mm (D) x 47 mm (H)

CAUTION			Do not use expired ink cartridges.
			The ink in the ink cartridge freezes at -16 °C (3.2 oF). It takes
			about three hours under 25 °C (77oF) until the ink thaws and
			becomes usable.

PRODUCT DESCRIPTION

Printing Specifications

16

Confidential

Epson Artisan 810/835/837/710/725/730/Epson Stylus Photo PX810FW/TX810FW/PX820FWD/TX820FWD/PX830FWD/PX710W/TX710W/PX720WD/TX720WD/PX730WD/TX730WD

Revision E

1.2.3 Print Mode

Table 1-4. Print Mode (Color)

	Media	Print Mode	Resolution	Dot Size	Bi-d	Micro	Border-
			(H x V) dpi	(cps*1)		Weave	less
	• Plain paper	Draft	360x180	Eco	ON	OFF	N/A
	• Premium Bright			(450cps)
	White Paper (EAI)
		Normal	360x360	MC2-1	ON	OFF	N/A
	• Premium Bright			(360cps)
	White Inkjet Paper
		Photo Fine	720x720	MC1-1	ON	ON	N/A
	(others)
				(240cps)
	• Ultra Premium Photo	Photo*2	720x720	MC1-2	ON	ON	OK
	Paper Glossy (EAI)		(1.0 pass)	(240cps)
	• Ultra Glossy Photo
		Photo*2	720x720	MC2-2	ON	ON	OK
	Paper (others)		(2.0 pass)	(280cps)
		Super Photo	5760x1440	MC1-5	ON	ON	OK
				(200cps)
	• Photo Paper Glossy			MC1-2
	(EAI)	Fine	720x360		ON	ON	OK
	• Glossy Photo Paper			(240cps)
	(others)
	• Premium Photo Paper		720x720	MC1-2
	Glossy (EAI)	Photo*2			ON	ON	OK
			(1.0 pass)	(240cps)
	• Premium Glossy
	Photo Paper (others)
	• Premium Photo Paper		720x720	MC2-2
	Semi-Gloss (EAI)	Photo*2			ON	ON	OK
			(2.0 pass)	(280cps)
	• Premium Semigloss
	Photo Paper (other)
	• Ultra Premium Photo	Super Photo	5760x1440	MC1-5	ON	ON	OK
	Paper Luster (EAI)
				(200cps)
	• Photo Paper
	• Premium Presentation	Photo*2	720x720	MC2-2	ON	ON	OK
	Paper Matte (EAI)		(2.0 pass)	(280cps)
	• Matte Paper -
		Super Photo	5760x1440	MC1-5	ON	ON	OK
	Heavyweight (others)			(200cps)
	• Presentation Paper
	Matte (EAI)	Photo*2	720x720	MC2-2	ON	ON	N/A
	• Photo Quality Inkjet		(2.0 pass)	(280cps)
	Paper*2 (others)

Table 1-4. Print Mode (Color)

	Media	Print Mode	Resolution	Dot Size	Bi-d	Micro	Border-
			(H x V) dpi	(cps*1)		Weave	less
		Normal	360x360	MC2-1	OFF	OFF	N/A
				(360cps)
	Envelope
		Photo Fine	720x720	MC1-1	OFF	ON	N/A
				(240cps)
	• Premium Presentation
	Paper Matte Double-		720x720	MC2-2
	sided (EAI)	Photo*2			ON	ON	N/A
			(2.0 pass)	(280cps)
	• Double-sided Matte
	Paper (Euro, Asia)
	Photo stickers	Photo*2	720x720	MC2-2	ON	ON	N/A
			(2.0 pass)	(280cps)
	• Iron-On Transfer
	Paper (EAI)			MC1-1
	• Iron-On Cool Peal	Photo Fine	720x720		OFF	ON	N/A
				(240cps)
	Transfer Paper
	(others)
	CD/DVD Label*3	Super Photo	5760x1440	MC1-5	ON	ON	N/A
				(200cps)
	High-quality CD/DVD	Super Photo	5760x1440	MC1-5	ON	ON	N/A
	Label*3			(200cps)

Note *1: cps = character per second

*2: Photo mode uses 1.0 pass or 2.0 pass depending on the paper size. 1.0 pass supported size: 4” x 6”

2.0 pass supported size: 5” x 7”, 8” x 10”, Letter, A4, 16:9 wide

*3: Print quality is not guaranteed in the settings other than [type: “CDR Tray” & media: “CD/DVD”] when carrying out CD/DVD printing from the PC.

PRODUCT DESCRIPTION

Printing Specifications

17

Confidential

Epson Artisan 810/835/837/710/725/730/Epson Stylus Photo PX810FW/TX810FW/PX820FWD/TX820FWD/PX830FWD/PX710W/TX710W/PX720WD/TX720WD/PX730WD/TX730WD

Revision E

Table 1-5. Print Mode (Monochrome)

	Media	Print Mode	Resolution	Dot Size	Bi-d	Micro	Border-
			(H x V) dpi	(cps*1)		Weave	less
	• Plain paper	Draft	360x180	Eco	ON	OFF	N/A
	• Premium Bright			(450cps)
	White Paper (EAI)
		Normal	360x360	MC2-1	ON	OFF	N/A
	• Premium Bright			(360cps)
	White Inkjet Paper
		Photo Fine	720x720	MC1-1	ON	ON	N/A
	(others)
				(240cps)
	• Ultra Premium Photo	Photo*2	720x720	MC1-2	ON	ON	OK
	Paper Glossy (EAI)		(1.0 pass)	(240cps)
	• Ultra Glossy Photo
		Photo*2	720x720	MC2-2	ON	ON	OK
	Paper (others)		(2.0 pass)	(280cps)
		Super Photo	5760x1440	MC1-5	ON	ON	OK
				(200cps)
	• Photo Paper Glossy			MC1-2
	(EAI)	Fine	720x360		ON	ON	OK
	• Glossy Photo Paper			(240cps)
	(others)
	• Premium Photo Paper		720x720	MC1-2
	Glossy (EAI)	Photo*2			ON	ON	OK
			(1.0 pass)	(240cps)
	• Premium Glossy
	Photo Paper (others)
	• Premium Photo Paper		720x720	MC2-2
	Semi-Gloss (EAI)	Photo*2			ON	ON	OK
			(2.0 pass)	(280cps)
	• Premium Semigloss
	Photo Paper (other)
	• Ultra Premium Photo	Super Photo	5760x1440	MC1-5	ON	ON	OK
	Paper Luster (EAI)
				(200cps)
	• Photo Paper
	• Premium Presentation	Photo*2	720x720	MC2-2	ON	ON	OK
	Paper Matte (EAI)		(2.0 pass)	(280cps)
	• Matte Paper -
		Super Photo	5760x1440	MC1-5	ON	ON	OK
	Heavyweight (others)			(200cps)
	• Presentation Paper
	Matte (EAI)	Photo*2	720x720	MC2-2	ON	ON	N/A
	• Photo Quality Inkjet		(2.0 pass)	(280cps)
	Paper*2 (others)

Table 1-5. Print Mode (Monochrome)

	Media	Print Mode	Resolution	Dot Size	Bi-d	Micro	Border-
			(H x V) dpi	(cps*1)		Weave	less
		Normal	360x360	MC2-1	OFF	OFF	N/A
				(360cps)
	Envelope
		Photo Fine	720x720	MC1-1	OFF	ON	N/A
				(240cps)
	• Premium Presentation
	Paper Matte Double-		720x720	MC2-2
	sided (EAI)	Photo*2			ON	ON	N/A
			(2.0 pass)	(280cps)
	• Double-sided Matte
	Paper (Euro, Asia)
	Photo stickers	Photo*2	720x720	MC2-2	ON	ON	N/A
			(2.0 pass)	(280cps)
	• Iron-On Transfer
	Paper (EAI)			MC1-1
	• Iron-On Cool Peal	Photo Fine	720x720		OFF	ON	N/A
				(240cps)
	Transfer Paper
	(others)
	CD/DVD Label*3	Super Photo	5760x1440	MC1-5	ON	ON	N/A
				(200cps)
	High-quality CD/DVD	Super Photo	5760x1440	MC1-5	ON	ON	N/A
	Label*3			(200cps)

Note *1: cps = character per second

*2: Photo mode uses 1.0 pass or 2.0 pass depending on the paper size. 1.0 pass supported size: 4” x 6”

2.0 pass supported size: 5” x 7”, 8” x 10”, Letter, A4, 16:9 wide

*3: Print quality is not guaranteed in the settings other than [type: “CDR Tray” & media: “CD/DVD”] when carrying out CD/DVD printing from the PC.

PRODUCT DESCRIPTION

Printing Specifications

18

Confidential

Epson Artisan 810/835/837/710/725/730/Epson Stylus Photo PX810FW/TX810FW/PX820FWD/TX820FWD/PX830FWD/PX710W/TX710W/PX720WD/TX720WD/PX730WD/TX730WD

Revision E

1.2.4 Supported Paper

The table below lists the paper type and sizes supported by the printer. The supported paper type and sizes vary depending on destinations (between EAI, EUR, and Asia).

Table 1-6. Supported Paper

				Thickness			EAI			EUR			Asia		Paper feed tray
	Paper Name		Paper Size		Weight										position*4
				(mm)		P*1	B*2	D*3	P*1	B*2	D*3	P*1	B*2	D*3	Tray 1	Tray 2
		Legal	215.9 x 355.6 mm (8.5”x14”)			Y	-	-	Y	-	-	Y	-	-	Y	-
		Letter	215.9 x 279.4 mm (8.5”x11”)			Y	-	Y	Y	-	Y	Y	-	Y	Y	-
		A4	210 x 297 mm (8.3”x11.7”)			Y	-	Y	Y	-	Y	Y	-	Y	Y	-
		B5	182 x 257 mm (7.2”x10.1”)		64-90 g/m2	-	-	-	Y	-	Y	Y	-	Y	Y	-
	Plain paper			0.08-0.11
		A5	148 x 210 mm (5.8”x8.3”)			-	-	-	Y	-	-	Y	-	-	Y	-
					(17-24 lb.)
		Half Letter	139.7 x 215.9 mm (5.5”x8.5”)			Y	-	-	-	-	-	-	-	-	Y	-
		A6	105 x 148 mm (4.2”x5.8”)			Y	-	-	Y	-	-	Y	-	-	-	Y
		User Defined	89 x 127215.9 x 1117.6 mm			Y	-	-	Y	-	-	Y	-	-	Y*5	-
			(3.5”x5” - 8.5”x44”)
	Premium Inkjet Plain Paper	A4	210 x 297 mm (8.3”x11.7”)	0.11	80 g/m2	-	-	-	Y	-	Y	-	-	-	Y	-
					(21 lb.)
	Premium Bright White Paper (EAI)	Letter	215.9 x 279.4 mm (8.5”x11”)	0.11	90 g/m2	Y	-	Y	-	-	-	-	-	-	Y	-
					(24 lb.)
	Bright White Inkjet Paper (Euro, Asia)	A4	210 x 297 mm (8.3”x11.7”)	0.13	92.5 g/m2	-	-	-	Y	-	Y	Y	-	Y	Y	-
					(25 lb.)
		Letter	215.9 x 279.4 mm (8.5”x11”)			Y	Y	-	-	-	-	-	-	-	Y	-
	Ultra Premium Photo Paper Glossy	A4	210 x 297 mm (8.3”x11.7”)		290 g/m2	-	-	-	Y	Y	-	Y	Y	-	Y	-
	(EAI)	8” x 10”	203.2 x 254 mm	0.30		Y	Y	-	-	-	-	-	-	-	Y	-
					(77 lb.)
	Ultra Glossy Photo Paper (Euro, Asia)
		5” x 7”	127 x 178 mm			Y	Y	-	Y	Y	-	-	-	-	-	Y
		4” x 6”	101.6 x 152.4 mm			Y	Y	-	Y	Y	-	Y	Y	-	-	Y
		Letter	215.9 x 279.4 mm (8.5”x11”)			Y	Y	-	-	-	-	-	-	-	Y	-
		A4	210 x 297 mm (8.3”x11.7”)			Y	Y	-	Y	Y	-	Y	Y	-	Y	-
	Premium Photo Paper Glossy (EAI)
		8” x 10”	203.2 x 254 mm		255 g/m2	Y	Y	-	-	-	-	-	-	-	Y	-
	Premium Glossy Photo Paper (Euro,			0.27
					(68 lb.)
		5” x 7”	127 x 178 mm			Y	Y	-	Y	Y	-	Y	Y	-	-	Y
	Asia)
		4” x 6”	101.6 x 152.4 mm			Y	Y	-	Y	Y	-	Y	Y	-	-	Y
		16:9 wide	101.6 x 180.6 mm			Y	Y	-	Y	Y	-	-	-	-	-	Y
	PRODUCT DESCRIPTION		Printing Specifications													19

Confidential

	Epson Artisan 810/835/837/710/725/730/Epson Stylus Photo PX810FW/TX810FW/PX820FWD/TX820FWD/PX830FWD/PX710W/TX710W/PX720WD/TX720WD/PX730WD/TX730WD														Revision E
			Table 1-6. Supported Paper
				Thickness			EAI			EUR			Asia		Paper feed tray
	Paper Name		Paper Size		Weight										position*4
				(mm)		P*1	B*2	D*3	P*1	B*2	D*3	P*1	B*2	D*3	Tray 1	Tray 2
		Letter	215.9 x 279.4 mm (8.5”x11”)			Y	Y	-	-	-	-	-	-	-	Y	-
	Photo Paper Glossy (EAI)	A4	210 x 297 mm (8.3”x11.7”)	0.25	258 g/m2	Y	Y	-	Y	Y	-	Y	Y	-	Y	-
	Glossy Photo Paper (Euro, Asia)	5” x 7”	127 x 178 mm		(68 lb.)	-	-	-	Y	Y	-	-	-	-	-	Y
		4” x 6”	101.6 x 152.4 mm			Y	Y	-	Y	Y	-	Y	Y	-	-	Y
	Premium Photo Paper Semi-Gloss	Letter	215.9 x 279.4 mm (8.5”x11”)		250 g/m2	Y	Y	-	-	-	-	-	-	-	Y	-
	(EAI)
		A4	210 x 297 mm (8.3”x11.7”)	0.27		-	-	-	Y	Y	-	Y	Y	-	Y	-
	Premium Semigloss Photo Paper				(66 lb.)
	(Euro, Asia)	4” x 6”	101.6 x 152.4 mm			Y	Y	-	Y	Y	-	Y	Y	-	-	Y
		A4	210 x 297 mm (8.3”x11.7”)		190 g/m2	-	-	-	Y	Y	-	Y	Y	-	Y	-
	Photo Paper
		5” x 7”	127 x 178 mm	0.24		-	-	-	Y	Y	-	-	-	-	-	Y
					(51 lb.)
		4" x 6"	101.6 x 152.4 mm			-	-	-	Y	Y	-	Y	Y	-	-	Y
	Premium Presentation Paper Matte	Letter	215.9 x 279.4 mm (8.5”x11”)			Y	Y	-	-	-	-	-	-	-	Y	-
	(EAI)				167 g/m2
		A4	210 x 297 mm (8.3”x11.7”)	0.23		-	-	-	Y	Y	-	Y	Y	-	Y	-
	Matte Paper Heavy-weight (Euro,				(44 lb.)
	Asia)	8” x 10”	203.2 x 254 mm			Y	Y	-	-	-	-	-	-	-	Y	-
	Premium Presentation Paper Matte	Letter	215.9 x 279.4 mm (8.5”x11”)		185 g/m2	Y	-	-	-	-	-	-	-	-	-	-
	Double-sided (EAI)			0.22
		A4	210 x 297 mm (8.3”x11.7”)		(49 lb.)	-	-	-	Y	-	-	Y	-	-	-	-
	Double-sided Matte Paper (Euro, Asia)
	Ultra Premium Photo Paper Luster	Letter	215.9 x 279.4 mm (8.5”x11”)	0.27	250 g/m2	Y	Y	-	-	-	-	-	-	-	Y	-
					(66 lb.)
	Presentation Paper Matte (EAI)	Letter	215.9 x 279.4 mm (8.5”x11”)		102 g/m2	Y	-	-	-	-	-	-	-	-	Y	-
	Photo Quality Inkjet Paper (Euro,			0.13
		A4	210 x 297 mm (8.3”x11.7”)		(27 lb.)	Y	-	-	Y	-	-	Y	-	-	Y	-
	Asia)
		#10	104.8 x 241.3 mm			Y	-	-	Y	-	-	Y	-	-	Y	-
			(4.125”x9.5”)		75-100 g/m2
	Envelopes			-
		#DL	110 x 220 mm		(20-27 lb.)	-	-	-	Y	-	-	Y	-	-	Y	-
		#C6	114 x 162 mm			-	-	-	Y	-	-	Y	-	-	Y	-
	Iron-On Cool Peal Transfer (EAI)	Letter	215.9 x 279.4 mm (8.5”x11”)	0.14	130 g/m2	Y	-	-	-	-	-	-	-	-	Y	-
	Iron-On Cool Peal Transfer Paper
		A4	210 x 297 mm (8.3”x11.7”)		(35 lb.)	-	-	-	Y	-	-	Y	-	-	Y	-
	(others)
	Photo Stickers 16	A6	105 x 148 mm (4.1”x5.8”)	0.19	---	-	-	-	-	-	-	Y	-	-	-	Y
	PRODUCT DESCRIPTION		Printing Specifications													20

Confidential

Epson Artisan 810/835/837/710/725/730/Epson Stylus Photo PX810FW/TX810FW/PX820FWD/TX820FWD/PX830FWD/PX710W/TX710W/PX720WD/TX720WD/PX730WD/TX730WD

Revision E

Table 1-6. Supported Paper

Thickness

EAI

EUR

Asia

Paper feed tray

Paper Name

Paper Size

Weight

position*4

(mm)

P*1

B*2

D*3

P*1

B*2

D*3

P*1

B*2

D*3

Tray 1

Tray 2

CD/DVD

ø12cm

ø12cm

---

---

Y

-

-

Y

-

-

Y

-

-

*6

-

ø8cm

ø8cm

---

---

Y

-

-

Y

-

-

Y

-

-

*6

-

CD/DVD Premium Surface

ø12cm

ø12cm

---

---

Y

-

-

Y

-

-

Y

-

-

*6

-

ø8cm

ø8cm

---

---

Y

-

-

Y

-

-

Y

-

-

*6

-

Note *1: “Y” in the “P” column stands for “the paper type/size is Supported”. *2: “Y” in the “B” column stands for “Borderless printing is available”. *3: “Y” in the “D” column stands for “Duplex printing is available”.

*4: See below for the Paper feed tray position.

Paper feed tray position

Tray 1

Tray 2

CDR Tray

*5: The paper other than the user definition range is not supported. *6: Front manual paper feeding with the built-in CDR Tray

CAUTION		Make sure the paper is not wrinkled, fluffed, torn, or folded.
	The curve of paper must be 5 mm or below.
	When printing on an envelope, be sure the flap is folded neatly.
	Do not use the adhesive envelopes.
		Do not use double envelopes and cellophane window envelopes.

PRODUCT DESCRIPTION

Printing Specifications

21

Confidential

Epson Artisan 810/835/837/710/725/730/Epson Stylus Photo PX810FW/TX810FW/PX820FWD/TX820FWD/PX830FWD/PX710W/TX710W/PX720WD/TX720WD/PX730WD/TX730WD

Revision E

1.2.5		Printing Area
The printing area for this printer is shown below.
			Table 1-7. Printing Area (Margins)
	Print Mode		Paper Size		Margin*
				Left	Right		Top	Bottom
	Standard print		Any size	3 mm	3 mm		3 mm	3 mm
			Envelope	5 mm	5 mm		3 mm	20 mm
	Borderless		4” x 6”	2.54 mm	2.54 mm		1.34 mm	2.54 mm
	print		Others				2.96 mm	4.02 mm
Note * :		The margins for Borderless print are margins that bleed off the edges of paper.

Cut Sheet (Standard)		Cut Sheet (Borderless)			Envelope
LM	RM	LM	RM	LM	RM
	TM		TM		TM
					Print Area
	Print Area		Print Area
	BM				BM

Paper

SIze

Paper Size

BM

Paper Feed Direction

Figure 1-1. Printing Area

1.3 Scanner Specifications

Table 1-8. Basic Specifications

				Specification
	Item	Epson Artisan 810/Epson			Epson Artisan 710/Epson
			Stylus Photo PX810FW/		Stylus Photo PX710W/
			TX810FW			TX710W
	Scanner type	Flatbed, color
	Scanning method	Moving carriage, stationary document
	Home position	The rear left corner
	Photoelectric device	CIS
	Light source	LED
	Maximum document sizes	A4 or US letter
	Scanning range	8.5” x 11.7” (216 mm x 297 mm)
		Main scan		: 4,800 dpi
	Maximum resolution			(1,200 dpi*)	Main scan	: 2,400 dpi
		Sub scan		: 4,800 dpi	Sub scan	: 4,800 dpi
				(600 dpi*)
	Maximum effective pixels	40,800 x 56,160 pixels			20,400 x 28,080 pixels
					(with 2,400 dpi scanning)
	Pixel depth	16 bit per pixel (input) and 1 bit or 8 bit per pixel (output).
	Note * : When scanning using ADF
		Table 1-9. ADF Specifications
	(Epson Artisan 810/Epson Stylus Photo PX810FW/TX810FW only)
	Item			Specification
	Document loading		Face-up
	Maximum document sizes		A4 or US letter or Legal
	Supported paper type		Plain paper only
	Paper thickness		64 to 95 g/m2
	Maximum number of		30 sheets (Xerox-P 64 g/m2) or 3 mm (A4, US Letter) /
	documents which can be set		10 sheet (Legal)
	Document path		Feeds from upper tray and ejects to lower tray
	Document set position		Left back

PRODUCT DESCRIPTION

Scanner Specifications

22

Confidential

Epson Artisan 810/835/837/710/725/730/Epson Stylus Photo PX810FW/TX810FW/PX820FWD/TX820FWD/PX830FWD/PX710W/TX710W/PX720WD/TX720WD/PX730WD/TX730WD

Revision E

1.3.1 Scanning Range

Table 1-10. Scanning Range

RL (read length)	RW (read width)	OLM (left margin)	OTM (top margin)
297 mm	216 mm	1.5 mm	1.5 mm

Scanning start position

Scanning direction

OLM
	a		Original
			(face down)
RW			Scan bed
			Scanning range
	OTM	RL

Figure 1-2. Scanning Range

1.4	General Specifications
1.4.1	Electrical Specifications
			Table 1-11. Primary Power Specifications
				Epson Artisan 810/Epson Stylus		Epson Artisan 710/Epson Stylus
	Item			Photo PX810FW/TX810FW		Photo PX710W/TX710W
				100-120 V	220-240 V	100-120 V	220-240 V
				model	model	model	model
Rated power				100 to 120	220 to 240	100 to 120	220 to 240
supply voltage				VAC	VAC	VAC	VAC
Input voltage range				90 to 132	198 to 264	90 to 132	198 to 264
				VAC	VAC	VAC	VAC
Rated current				0.8 A	0.4 A	0.8 A	0.4 A
(Max. rated current)				(1.6 A)	(0.8 A)	(1.6 A)	(0.8 A)
Rated frequency				50 to 60 Hz		50 to 60 Hz
Input frequency range				49.5 to 60.5 Hz		49.5 to 60.5 Hz
Energy conservation				International Energy Star Program compliant
		Copy
		(ISO/		Approx. 26 W		Approx. 25 W
		IEC24712
Power		Pattern)
consumption
		Ready		Approx. 12 W		Approx. 9.5 W
		Sleep		Approx. 5.5 W		Approx. 5.0 W
		Off		Approx. 0.3 W		Approx. 0.3 W	Approx. 0.5 W

Note : If the product has been idle status over 13 minutes, it goes into sleep mode within 2 minutes.

PRODUCT DESCRIPTION

General Specifications

23

Confidential

Epson Artisan 810/835/837/710/725/730/Epson Stylus Photo PX810FW/TX810FW/PX820FWD/TX820FWD/PX830FWD/PX710W/TX710W/PX720WD/TX720WD/PX730WD/TX730WD

Revision E

1.4.2 Safety Approvals (Safety standards/EMI)

USA	UL60950-1
	FCC Part15 Subpart B Class B
Canada	CAN/CSA-C22.2 No.60950-1
	CAN/CSA-CEI/IEC CISPR 22 Class B
EU	EN60950-1
	EN55022 Class B
	EN61000-3-2, EN61000-3-3
	EN55024
Germany	EN60950-1
Russia	GOST-R (IEC60950, CISPR 22)*
Australia	AS/NZS CISPR22 Class B

Note* : Epson Artisan 710/Epson Stylus Photo PX710W/TX710W only.

1.4.3 Acoustic Noise

Epson Artisan 810/Epson Stylus Photo PX810FW/TX810FW

PC Printing*1: TBD dB

Scanning*2: TBD dB

Epson Artisan 710/Epson Stylus Photo PX710W/TX710W

PC Printing*1: TBD dB

Scanning*2: TBD dB

Note *1: Premium Glossy Photo Paper/Highest quality *2: default setting

1.4.4 Durability (TBD)

	Item		Durability	Remark
		Black	16,000 pages, or five years	• When printing A4 size sheet
	Total print life		whichever comes first	• Black: 3.5% duty, Color: 5%
				duty
		Color	10,000 pages, or five years
			whichever comes first
	Printhead		Six billions shots (per nozzle) or
			five years whichever comes first
	Scanner carriage		30,000 cycles of carriage movement
	Total ADF feeding*		10,000 pages

Note * : Epson Artisan 810/Epson Stylus Photo PX810FW/TX810FW only.

1.4.5 Environmental Conditions

Table 1-12. Environmental Conditions

	Condition	Temperature*1	Humidity*1,2	Shock	Vibration
	Operating	10 to 35°C	20 to 80%	1 G	0.15 G,
		(50 to 95°F)		(1 msec. or less)	10 to 55 Hz
	Storage	-20 to 40°C*3	5 to 85%	2 G	0.50 G,
	(unpacked)	(-4°F to 104°F)		(2 msec. or less)	10 to 55 Hz

Note *1: The combined Temperature and Humidity conditions must be within the blue-shaded range in Fig.1-3.

*2: No condensation

*3: Must be less than 1 month at 40°C.

	90
	80
	70
	60
Humidity (%)	50
	40
	30
	20
			27/80
	10/50	20/68	30/86	35/95	40/104

Temperature (°C/°F)

Figure 1-3. Temperature/Humidity Range

CAUTION	When returning the repaired printer to the customer, make sure
	the Printhead is covered with the cap and the ink cartridge is
	installed.

If the Printhead is not covered with the cap when the printer is off, turn on the printer with the ink cartridge installed, make sure the Printhead is covered with the cap, and then turn the printer off.

PRODUCT DESCRIPTION

General Specifications

24

Confidential

Epson Artisan 810/835/837/710/725/730/Epson Stylus Photo PX810FW/TX810FW/PX820FWD/TX820FWD/PX830FWD/PX710W/TX710W/PX720WD/TX720WD/PX730WD/TX730WD

Revision E

1.5 Interface

The following is the specifications of the USB Interface, Network Interface, FAX Interface (Epson Artisan 810/Epson Stylus Photo PX810FW/TX810FW only), and Memory Card Slot mounted on this printer.

1.5.1 USB Interface

The table below describes the specifications of the two USB ports; USB device port for connecting with a host such as a computer, and the USB host port for connecting with an external devices such as a DSC (digital still camera).

Table 1-13. USB Interface Specifications

Item	USB Device port		USB Host port*
	• Universal Serial Bus		• Universal Serial Bus
	Specifications Revision 2.0		Specifications Revision 2.0
	• Universal Serial Bus Device
Compatible standards	Class Definition for Printing
	Devices Version 1.1
	• Universal Serial Bus Mass
	Storage Class Bulk-Only
	Transport Revision 1.0
Transfer rate	480 Mbps (High Speed)		480 Mbps (Max.)
Data format		NRZI
Compatible connector	USB Series B		USB Series A
Max. cable length	2 [m]		or less

Note* : The following devices can be connected to the USB Host port.

•Devices compliant with DPS Version 1.0/1.1 (PictBridge)

•Devices compliant with Universal Serial Bus Mass Storage Class Bulk-Only Transport Revision 1.0, and the Subclass code is one of the followings.

0x06 (SCSI transparent command set)

0x05 (SFF-8070i command set)

0x02 (SFF-8020i command set)

Table 1-14. Device ID

When IEEE 1284.4 is Enabled	When IEEE 1284.4 is Disabled
@EJL<SP>ID<CR><LF>	@EJL<SP>ID<CR><LF>
MFG:EPSON;	MFG:EPSON;
CMD:ESCPL2,BDC,D4,D4PX, ESCPR2;	CMD:ESCPL2,BDC, ESCPR2;
MDL:Model Name;	MDL:Model Name;
CLS:PRINTER;	CLS:PRINTER;
DES:EPSON<SP>Model Name;	DES:EPSON<SP>Model Name;
CID:EpsonRGB;	CID:EpsonRGB;

Note : The “Model Name” is replaced as shown in the following table.

Table 1-15. Model Names Indicated in the Device ID

		Model Name
	Destination	Epson Artisan 810/Epson	Epson Artisan 710/Epson
		Stylus Photo PX810FW/	Stylus Photo PX710W/
		TX810FW	TX710W
	North America	Artisan 810	Artisan 710
	Euro	Epson Stylus Photo PX810FW	Epson Stylus Photo PX710W
	Asia/Pacific	Epson Stylus Photo TX810FW	Epson Stylus Photo TX710W

1.5.2FAX Interface (Epson Artisan 810/Epson Stylus Photo PX810FW/TX810FW only)

Port Name	Connector	Description
Line port	RJ11	Connects to phone cable from modular wall jack.
EXT port	RJ11	Connects to TAM or Telephone.

1.5.3 Network Interface

Epson Artisan 810/Epson Stylus Photo PX810FW/TX810FW/Epson Artisan 710/ Epson Stylus Photo PX710W/TX710W can be connected to the network via Wired or Wireless LAN connection, however, they can not be used simultaneously. The following describes each Interface.

Wired LAN

The following interface is equipped for the Wired LAN connection. The communication mode can be selected from auto setting or fixed setting.

	Table 1-16. Wired LAN
Item	Content
Connector	RJ-45 receptacle*: 1 port
Communication Speed	For either 10Base-T or 100Base-TX, the Full Duplex or Half
	Duplex can be selected.

Note* : 10Base-T/100Base-TX Ethernet is supported. MDI/MDI-X is selected automatically.

PRODUCT DESCRIPTION

Interface

25

Confidential

Epson Artisan 810/835/837/710/725/730/Epson Stylus Photo PX810FW/TX810FW/PX820FWD/TX820FWD/PX830FWD/PX710W/TX710W/PX720WD/TX720WD/PX730WD/TX730WD

Revision E

Table 1-17. Combination of the Wired LAN communication mode settings

	Setting of this printer	Setting of the connected device
		Auto Setting (AUTO)
	Auto Setting
		100BASE-TX Half Duplex
		10BASE-T Half Duplex
	100BASE-TX Full Duplex	100BASE-TX Full Duplex
	100BASE-TX Half Duplex	Auto Setting (AUTO)
		100BASE-TX Half Duplex
	10BASE-T Full Duplex	10BASE-T Full Duplex
	10BASE-T Half Duplex	Auto Setting (AUTO)
		10BASE-T Half Duplex

Wireless LAN

The following interface is equipped for the Wireless LAN connection.

	Table 1-18. Wireless LAN
Item		Content
Applied Standard	Conforms to IEEE802.11b, IEEE802.11g
(2.4GHz spectrum band
wireless network
standards)
Wireless Operation Mode	IEEE802.11b	DS-SS (Half Duplex)
	IEEE802.11g	OFDM (Half Duplex)
Communication Range	IEEE802.11b (11 Mbps)	• 60 m (indoor)
(line-of-sight distance)*		• 220 m (outdoor)
	IEEE802.11g (54 Mbps)	• 20 m (indoor)
		• 100 m (outdoor)
Communication Mode	Ad-hoc (IBSS) or Infrastructure	(ESS)
Roaming Function	Not supported
Output Signal Intensity	10 mW
Antenna	Built-in antenna (Diversity function is supported)

Note * : Referential value. It depends on surrounding conditions.

Table 1-19. Available Channels and Standard

Frequency Band		Channel	IEEE Standard	Communication Speed
	(GHz)			(bps)*
2.400	- 2.4835	1 - 13	802.11b	11/5.5/2/1 M
2.400	- 2.4835	1 - 13	802.11g	54/48/36/24/18/12/9/6 M
2.471	- 2.497	14	802.11/11b	11/5.5/2/1 M

Note "*": The communication speed will be changed automatically, depending on radio wave strength. bps = bit per second.

Switching Wired/Wireless LAN

This printer can be connect to the network via either Wired LAN or Wireless LAN connection only.

Enabling/disabling the Wireless LAN can be made from the Control Panel. When the Wireless LAN is enabled, it gets priority over the Wired LAN regardless of whether the LAN Cable is connected. The default Wireless LAN setting is “Disabled”.

Table 1-20. Wireless LAN Setting from the Control Panel

	Setting from Control Panel		LAN Cable Connection State
			Connected	Disconnected
	Wireless LAN	Disabled	Wired LAN	---*
		(Default)
		Enabled	Wireless LAN	Wireless LAN

Note* : No service via network is available without connecting the LAN Cable (because network communication is not established) except printing a status sheet or the like.

CHECK		When changing the networks while the power is on, wait at least for
POINT		10 seconds between disconnecting and reconnecting.

PRODUCT DESCRIPTION

Interface

26

Confidential

Epson Artisan 810/835/837/710/725/730/Epson Stylus Photo PX810FW/TX810FW/PX820FWD/TX820FWD/PX830FWD/PX710W/TX710W/PX720WD/TX720WD/PX730WD/TX730WD Revision E

1.5.4 Memory Card Slots

CAUTION If you insert a Memory Stick DUO to the Memory Card Slot without using the adapter, make sure to turn off the printer first,

then remove the card using tweezers.

Table 1-21. List of Supported Memory Card

	Priority	Slot	Compatible memory card	Standard	Max.	Remarks
					capacity
	1	Memory Stick/	Memory Stick	MemoryStick Standard Format Specification Ver.1.43-00 compatible	128MB	Includes versions with memory select function
		Memory Stick
			MagicGate Memory Stick	---	---	Copy protection function is not supported
		PRO
			MagicGate Memory Stick Duo	---	---	The Memory Stick Duo adapter should be used.
			Memory Stick PRO	Memory Stick Pro Format Specifications Ver.1.02-00 compatible	32GB	Copy protection function is not supported
			Memory Stick Duo	MemoryStick Duo Format Specification Ver.1.10-00 compatible	---	The Memory Stick Duo adapter should be used
			Memory Stick Pro Duo	---	---	The Memory Stick Duo adapter should be used.
			Memory Stick micro	---	---	The Memory Stick adapter for standard size should be used.
			Memory Stick Pro-HG Duo	---	---	The Memory Stick Duo adapter should be used.
		SD/MMC	SD (Security Digital)	SD Memory Card Specifications / PART1. Physical Layer Specification Ver.	2GB	---
				2.0 compatible
			miniSD/microSD			The SD adapter should be used
			SDHC		32GB	Speed Class is not supported
			miniSDHC/microSDHC			The SD adapter should be used
						Speed Class is not supported
			MultiMediaCard	MultiMediaCard Standard Ver. 4.2 compatible	4GB/32MB	Only MultiMediaCard Plus supports up to 32GB.
			MultiMediaCard Plus
			MultiMediaCard mobile			The Multi Media Card adapter for standard size should be
			MultiMediaCard micro			used.
		xD-Picture card*	xD-Picture card	xD-Picture Card Specification Ver.1.2 compatible	2GB	Type M/H supported
	2	CF Type II	Compact Flash	CompactFlash Specification Revision 2.1 compatible	32GB	True-IDE compatible memory card only
			Microdrive	---	---	---

Note* : FAT32 is not specified in the xD-Picture card standards. This printer supports only reading of xD-Picture card formatted in FAT32.

Note: • Memory Stick/PRO, SD/MMC and xD-Picture Card shares the same slot.

•When cards are inserted in the two slots at once, the slot which will be accessed first is determined according to the priority shown in the table.

•To select a card that has been inserted in a non-active slot, first remove the card in the active slot.

•In memory card direct printing mode, the image files in the active slot are valid and have assigned frame numbers. The number of images will not change if a card is inserted in another nonselected slot.

•When the card inserted in the slot is accessed from the PC, only one drive is displayed at a time as a removable disk* and only the card that is in the active slot can be accessed via the removable disk. A card that has been inserted into a non-selected slot cannot be accessed. (This is for Windows. For Macintosh, the card in the active slot will be mounted on the desktop.)

•Does not support 5V type of memory cards.

•When a memory card is being accessed, do not touch the memory card.

•For detailed information on the supported file system and formatting the memory card, refer to “1.7.2 Memory Card Direct Print Function (Photos Mode) (p.33)”.

PRODUCT DESCRIPTION

Interface

27

Confidential

Epson Artisan 810/835/837/710/725/730/Epson Stylus Photo PX810FW/TX810FW/PX820FWD/TX820FWD/PX830FWD/PX710W/TX710W/PX720WD/TX720WD/PX730WD/TX730WD

Revision E

1.6 Control Panel

1.6.1 Operation Buttons & LEDs

Power Button

LCD

Unlock button

Power LED

CD Tray button

Blue status light

Touch Panel

Figure 1-4. Control Panel for Epson Artisan 810/Epson Stylus Photo PX810FW/TX810FW (EAI version as a sample)

Display/Crop button LCD

Menu button

-, + button Cross Key and OK button

Power button

Unlock button

Power LED

Start button

Home button

CD Tray button

Stop/Clear Settings button

Back button

Blue status light

View Auto Correct button

Figure 1-5. Control Panel for Epson Artisan 710/Epson Stylus Photo PX710W/TX710W (EAI version as a sample)

PRODUCT DESCRIPTION Control Panel 28

Confidential

Epson Artisan 810/835/837/710/725/730/Epson Stylus Photo PX810FW/TX810FW/PX820FWD/TX820FWD/PX830FWD/PX710W/TX710W/PX720WD/TX720WD/PX730WD/TX730WD

Revision E

Table 1-22. Button Functions

(Epson Artisan 810/Epson Stylus Photo PX810FW/TX810FW)

	Button	Function
	Power	Turns the power ON/OFF.
	Touch Panel	Displays available buttons in each mode.
	Unlock button	Release the lock of tilt adjustment of the Control Panel while
		pressing.
	CD Tray	Ejects/retracts the CDR Tray.

Table 1-23. Button Functions

(Epson Artisan 710/Epson Stylus Photo PX710W/TX710W)

	Button	Function
	Power	Turns the power ON/OFF.
	Display/Crop	• Goes to the zoom setting screen for the selected image.
		• Changes the image preview layout on the LCD.
	-, +	Sets pages to print
	Unlock	Release the lock of the Control Panel.
	Start	Starts printing.
		• Stops operation and displays the menu screen.
	Stop/Clear Settings	• Stops printing and ejects paper.
		• Returns the print settings in the current mode to their defaults
		and displays the Top screen. (Returns to the previous screen
		during printing maintaining the current settings)
	Back	Cancels the previous operation.
	Cross Key/OK	• Selects a menu item or a setting value.
		• Accepts the changed settings
	Menu	Goes to the menu screen for each mode.
	Auto Correct	Changes the Auto Correct ON/OFF.
	CD Tray	Ejects/retracts the CDR Tray.
	Home	Changes modes in the following order.
		Copy/Print Photos/Scan/Setup

	Table 1-24. LED
LED	Function
	• Flashes while powering ON/OFF.
	• Flashes during some sequence is in progress.
Power (Green)	• Flashes when a fatal/maintenance error occurs.
	• Lights when the status is other than above.
	(Stand by mode/during setting on the Panel, etc.)
Blue status light	Flashes or lights according to the printer status.

1.6.2 Control Panel Functions in Each Mode

1.6.2.1 Control Panel Functions

The table below shows the print setting menu items for each mode and their defaults, and when the settings are saved or returned to their defaults. Explanations on detailed control panel functions of the Epson Artisan 810/Epson Stylus Photo PX810FW/ TX810FW/Epson Artisan 710/Epson Stylus Photo PX710W/TX710W are omitted here, because the LCD displays the detailed instruction.

Table 1-25. Timing of Saving or Initializing Control Panel Settings

	Mode	Print Setting	Default Value
Copy	Normal Copy	Copy Type	Color
		Density	±0
		Layout	With Border
		2-Sided Printing	Off
		Reduce/Enlarge	Actual
		Paper Size	• EAI: Letter
			• Euro/Asia: A4
		Paper Type	Plain Paper
		Document Type	Text & Image
		Quality	Standard Quality
		Expansion	Standard
		Dry Time	Standard
		Binding Direction	Vertical-Long

PRODUCT DESCRIPTION

Control Panel

29

Confidential

Epson Artisan 810/835/837/710/725/730/Epson Stylus Photo PX810FW/TX810FW/PX820FWD/TX820FWD/PX830FWD/PX710W/TX710W/PX720WD/TX720WD/PX730WD/TX730WD

Revision E

Table 1-25. Timing of Saving or Initializing Control Panel Settings

	Mode	Print Setting	Default Value
Copy	Photo Copy	Color Restoration	Off
		Paper Size	4” x 6” (10 x 15 cm)
		Paper Type	Prem. Glossy
		Boderless	On
		Expansion	Standard
		Fix Photo*1	Fix Photo Off
		Enhance*2	Enhance Off
		Filter	Off
	CD/DVD Print	CD Inner/Outer	Standard
		Print Type	Print on a CD/DVD
		Document Type	Text & Image
		Quality	Best
Print Photo	• View and Print Photos	Paper Size	4” x 6” (10 x 15 cm)
	• Print All Photos
		Paper Type	Prem. Glossy
		Borderless	On
		Layout	Boderless
		Quality	Standard Quality
		Expansion	Standard
		Date	Off
		Print Info. On Photos	Off
		Fit Frame	On
		Bidirectional	On
		Fix Photo*1	Fix Photo On
		Enhance*2	PhotoEnhance
		Scene Detection	Automatic
		Fix Red-Eye	Off *3
		Filter	Off
		Brightness	Standard
		Contrast	Standard
		Sharpness	Standard
		Saturation	Standard
Print Photo	Print Photo Greeting Card	Paper Size	• EAI: Letter
			• Euro/Asia: 4” x 6” (10 x 15 cm)
		Paper Type	Prem. Glossy

Table 1-25. Timing of Saving or Initializing Control Panel Settings

	Mode	Print Setting	Default Value
Print Photo	Print Photo Greeting Card	Layout	• EAI: 3-up
			• Euro/Asia: Borderless
		Frame	Off
		Fix Photo*1	Fix Photo On
		Enhance*2	PhotoEnhance
		Scene Detection	Automatic
		Fix Red-Eye	Off
		Filter	Off
		Brightness	Standard
		Contrast	Standard
		Sharpness	Standard
		Saturation	Standard
	Photo Layout Sheet	Layout	2-up
		Paper Size	4” x 6” (10 x 15 cm)
		Paper Type	Prem. Glossy
		Layout Method	Automatic layout
		Photo Layout	Place this photo
		Quality	Standard Quality
		Expansion	Standard
		Date	Off
		Print Info. On Photos	Off
		Fit Frame	On
		Bidirectional	On
	Print on CD/DVD	Layout	CD/DVD 1-up
		Layout Method	Automatic layout
		Photo Layout	Place this photo
		CD Inner/Outer	Standard
		Print Type	Print on a CD/DVD
		CD Density	Standard Density
		Fix Photo*1	Fix Photo On
		Enhance*2	PhotoEnhance
		Scene Detection	Automatic
		Fix Red-Eye	Off - This photo
		Filter	Off
		Brightness	Standard
		Sharpness	Standard
		Saturation	Standard

PRODUCT DESCRIPTION

Control Panel

30

Confidential