Page 1
Product Highlights
Flexibility and Reliabilty
A combination of Gigabit RJ-45 and SFP ports provide
the exibility to adapt to a wide range of applications
and environments
Security and Authentication Features
Robust security features, including the D-Link
Safeguard Engine™, protect against malicious attacks,
while authentication tools allow access control
Designed for Metro Ethernet
Surge protection, advanced Layer 2 functions,
extensive suite of security and management tools
makes these switches ideal for Metro Ethernet
applications
DGS-1210/ME Series
Metro Ethernet Switches
Features
Flexible Hardware Design
• Available in multiple congurations:
• Dierent combinations of 1000BASE-T,
1000BASE-T PoE and 1G SFP ports
• PoE and non-PoE variations
• Designed for standard 1U rack-mounting
• Rear panel RPS connector for an additional
external power supply (for non-PoE models)
Layer 2 Features
• 16K MAC address table
• IEEE 802.1D STP, 802.1w RSTP, and 802.1s MSTP
• Loopback detection
• Supports IEEE 802.3ad Link Aggregation
• Port-based Q-in-Q
• VLAN Trunking
Security and Authentication
• Port security
• SSH/SSL
• IP-MAC-Port Binding (IMPB)
• Access Control List (ACL) and IEEE 802.1X
• Guest VLAN
Reliability and Maintenance
• Surge protection on all Gigabit Ethernet ports
• ITU-T G.8032 ERPS sub-50 ms protection and
recovery
• Dying Gasp for quick trouble shooting during
power failures or system shut downs
The DGS-1210/ME Series Metro Ethernet Switches are a range of switches designed for
Metro Ethernet applications. They feature a variety of port congurations, including
10/100/1000BASE-T RJ-45 ports and 1G SFP ports for increased network bandwidth. Surge
protection, advanced Layer 2 functions, and a suite of security and management tools make
the DGS-1210/ME Series Metro Ethernet Switches ideal for Metro Ethernet applications.
Multi-Gigabit Performance
The DGS-1210/ME Series Metro Ethernet Switches come in a variety of port setups, including
1
Gigabit Ethernet RJ-45 or 1G Ethernet SFP ports. All models oer four 1G Ethernet SFP ports
for long distance Gigabit bre connectivity. The DGS-1210-28MP/ME switch feature Power over
Ethernet (PoE) with 370W PoE power budget, allowing compatible devices to be installed and
powered in remote locations without immediate access to power outlets.
Ecient and Resilient
For mission critical environments, the DGS-1210/ME Series Metro Ethernet Switches support
IEEE 802.1D 2004 edition, 802.1w, and 802.1s Spanning Tree Protocols (STP). The Spanning
Tree Protocol allows the switches to participate in Spanning Tree topology, providing an
alternative Layer 2 path in the event of a network failover. The switches also support IEEE
802.3ad link aggregation, which enables multiple ports to be grouped to form a single virtual
port, increasing bandwidth and redundancy for higher availability. This series furthermore
features IEEE 802.1p Quality of Service (QoS), allowing for real-time trac classication into
Weighted Round Robin (WRR) and strict priority levels mapped to 8 queues. Advanced trac
classication parameters allow the network to be tuned for exible congurations for specic
multimedia applications such as VoIP or IPTV.
2
Page 2
DGS-1210/ME Series Metro Ethernet Switches
Security & Authentication
The DGS-1210/ME Series supports IEEE 802.1X port-based/host-based
access control, guest VLAN, and RADIUS/TACACS+ authentication for strict
access control to the network. The IP-MAC-Port Binding (IMPB) feature allows
administrators to associate a source IP address with a designated MAC
address and also oers the exibility to dene the port number to enhance
user access control. The built-in D-Link Safeguard Engine™ protects the CPU
from broadcast, multicast, and unicast ooding by automatically trapping
packets and logging events in these situations. In addition, the Access Control
List (ACL) feature enhances network security and switch performance.
Management Capabilities
A user-friendly web interface gives administrators access to advanced
management features such as DHCP auto-conguration. This enables
switches to load their conguration from a TFTP server once they have
been assigned an IP address, allowing central management of device
congurations. The switches support Link Layer Discovery Protocol (LLDP),
which advertises the device’s capabilities and identity to the local network,
allowing administrators to better manage their network topology. Each port
also supports cable diagnostics, which can be used to troubleshoot cable
length and functionality problems remotely, resulting in lower management
overheads.
Trac & Bandwidth Control
Integrated bandwidth control allows network administrators to dene the
throughput levels for ingress and egress bandwidth. It provides a minimum
granularity of 64 Kbps for ingress port and ow-based bandwidth control,
and a minimum granularity of 64 Kbps for egress queue bandwidth.
The DGS-1210/ME Series also supports trac control, which optimises
performance by dropping packets when exceeding a set threshold, while
port mirroring helps administrators facilitate trac diagnostics and track
network performance. The DGS-1210/ME Series also provides IGMP snooping
with IGMP authentication to prune multicast trac and to optimise available
bandwidth.
Multicast Applications
The DGS-1210/ME Series features a full set of L2 multicast functions, including
IGMP snooping, IGMP ltering, fast leave, and multicast trac conguration
for specic ports. With L2 multicast support, the DGS-1210/ME Series is ready
and capable of handling growing IPTV applications. Host-based IGMP/MLD
snooping allows for multiple multicast subscribers per physical interface, and
ISM VLAN sends multicast streams in a multicast VLAN, saving bandwidth on
the backbone. Additionally, ISM VLAN proles allow users to bind or replace
the predened multicast registration information to subscriber ports quickly
and easily.
If the worst should happen to your network you need the very best
support and fast. Downtime costs your business money. D-Link
Assist maximises your uptime by solving technical problems
quickly and eectively. Our highly trained technicians are on
standby around the clock, ensuring that award-winning support
is only a phone call away.
With a choice of three aordable service oerings covering all
D-Link business products, you can select the package that suits
you best:
D-Link Assist Gold - for comprehensive 24-hour support
D-Link Assist Gold is perfect for mission-critical environments
where maximum uptime is a high priority. It guarantees four hour
around-the-clock response. Cover applies 24/7 for every day of the
year including holidays.
D-Link Assist Silver - for prompt same-day assistance
D-Link Assist Silver is designed for ‘high availability’ businesses that
require rapid response within regular working hours. It provides a
four hour response service Monday to Friday from 8am to 5pm,
excluding holidays.
D-Link Assist Bronze - for guaranteed response on the
next business day
D-Link Assist Bronze is a highly cost-eective support solution for
less critical environments. Response is guaranteed within eight
business hours Monday to Friday from 8am to 5pm, excluding
holidays.
D-Link Assist can be purchased together with any D-Link business
product. So whether you’re buying switching, wireless, storage,
security or IP Surveillance equipment from D-Link, your peace
of mind is guaranteed. D-Link Assist also oers installation and
conguration services to get your new hardware working quickly
and correctly.
Page 3
DGS-1210/ME Series Metro Ethernet Switches
Technical Specications DGS-1210-20/ME DGS-1210-28/ME DGS-1210-28MP/ME
Interface
Size • 11-inch standard rack-mount width
• 1U height
Interfaces • 16 10/100/1000BASE-T
• 4 1G SFP
PoE Support • Ports 1 to 24 compliant with IEEE 802.3at
Console Port RJ-45 console port
Other Port Standards &
Functions
• IEEE 802.3ab 1000BASE-T Gigabit Ethernet (twisted-pair copper)
Network Cables • UTP Cat. 5, Cat. 5e (100 m max.)
Full/Half-Duplex • Full/half-duplex for 10/100 Mbps speeds
Media Interface Exchange • Auto MDI/MDIX adjustment for all twisted-pair ports
• 19-inch standard rack-mount width
• 1U height
• 24 10/100/1000BASE-T
• 4 1G SFP
• IEEE 802.3i 10BASE-T Ethernet (twisted-pair copper)
• IEEE 802.3u 100BASE-TX Fast Ethernet (twisted-pair copper)
• IEEE 802.3az compliance
• Auto-negotiation
• IEEE 802.3x Flow Control
• IEEE 802.3z 1000BASE-X Gigabit Fiber
• Full-duplex for 1000 Mbps speed
• 19-inch standard rack-mount width
• 1U height
• 24 10/100/1000BASE-T PoE
• 4 1G SFP
Performance
Switching Capacity 40 Gbps 56 Gbps 56 Gbps
64-byte Max. Forwarding Rate 29.80 Mpps 41.7 Mpps 41.7 Mpps
MAC Address Table Size 16K entries
CPU Memory 256 MB DDR3
Packet Buffer 1.5 MB 1.5 MB 1.5 MB
Flash Memory 32 MB
LEDs
Power (per device)
Console (per device)
Link/Active/Speed (per port)
Fan Error
Page 4
DGS-1210/ME Series Metro Ethernet Switches
Physical/Environmental DGS-1210-20/ME DGS-1210-28/ME DGS-1210-28MP/ME
MTBF 349,836 hours 497,918 hours 267,960 hours
Acoustic
Heat Dissipation 47.67 BTU/hr 60.12 BTU/hr 1552.32 BTU/hr
Power Input AC Input: 100 to 240 V AC, 50/60 Hz
Maximum Power
Consumption
Maximum PoE Budget 370 W
Standby Power Consumption 6.95 W 8.21 W 21.8 W
Dimensions (W x D x H) 280 x 180 x 44 mm 440 x 140 x 44 mm 440 x 250 x 44 mm
Ventilation Fanless Fanless 3 x Smart fans
Weight 1.38 kg 2.21 kg 3.96 kg
Power Surge Protection All Gigabit Ethernet ports support IEC 61000-4-5 surge protection
Operating Temperature -5 to 50 °C (23 to 122 °F)
Storage Temperature -40 to 70 °C (-40 to 158 °F)
Operating Humidity 10% to 90% non-condensing
0 dB(A) 0 dB(A)
13.97 W 19.14 W
High Speed: 52.4 dB(A)
Low Speed: 47.9 dB(A)
445 W (PoE on)
35.6 W (PoE off)
Storage Humidity 5% to 90% non-condensing
EMI FCC class A, CE class A, VCCI, BSMI, CCC
Safety Certifications CE, LVD, UL, CB
Software
L2 Features • MAC address table: 16K entries
• Spanning Tree Protocols
- 802.1D STP
- 802.1w RSTP
- 802.1s MSTP
- BPDU filtering
- Root restriction
• Loopback detection
L2 Multicasting • IGMP Snooping
- IGMP v1/v2 snooping, v3 awareness
- IGMP authentication/filtering
- Supports 256 groups
- VLAN/host-based IGMP snooping fast leave
- Report suppression
VLAN • 802.1Q tagged VLAN
• VLAN group
• Max. 4094 VLAN groups
• Port-based VLAN
• GVRP
• Asymmetric VLAN
• Max. 256 dynamic VLAN
• Mirroring
- Support 1 mirroring group
- Support One-to-One, Many-to-One,
Flow-based (ACL) mirroring for ingress traffic
• L2 Protocol Tunneling (L2PT )
• Link aggregation
- Compliant with 802.3ad
- Supports max. 8 groups, 8 ports per group
• Ethernet Ring Protection Switching (ERPS)
• MLD Snooping
- MLD v1, MLD v2 awareness
- Supports 256 groups
• 802.1v protocol VLAN
• VLAN trunking
• MAC-based VLAN
• Port-based Q-in-Q
• ISM VLAN (multicast VLAN)
• Private VLAN
Page 5
DGS-1210/ME Series Metro Ethernet Switches
L3 Features • Max. 256 ARP entries
• Supports 255 static ARP entries
• Static route
- 64 IPv4 static routes
- 32 IPv6 static routes
Quality of Service (QoS) • CoS based on:
- Switch port
- 802.1p priority queues
- VLAN ID
- MAC address
- IPv4/IPv6 address
- DSCP
- TOS
- Protocol type
- TCP/UDP port
- IPv6 traffic class
Access Control List (ACL) • ACL based on
- Switch port
- 802.1p priority
- VLAN ID
- MAC address
- EtherType
- TOS
- IPv4/v6 address
- DSCP
- Protocol type
- IPv4/IPv6 TCP/UDP port number
- ICMP
- IPv6 traffic class
• Supports Gratuitous ARP
• Default route
• Bandwidth control
- Port-based (ingress, min. granularity 64 Kbps)
- Flow-based (ingress, min. granularity 64 Kbps)
- Egress queue bandwidth control (min. granularity 64 Kbps)
• Queue handling
- Strict priority
- Weighted Round Robin (WRR)
• 8 outbound queues
• Up to 256 ingress access rules
• ACL action (permit/deny/mirror)
• Time-based ACL
• ACL statistics
• CPU interface filtering
Authentication, Authorization,
and Accounting (AAA)
Security • SSH v2
Operations, Administration,
and Maintenance (OAM)
Management • Web-based GUI (IPv4/IPv6)
• 802.1X
- Host-based access control
- Port-based access control
• Guest VLAN
• Host-based MAC authentication
• RADIUS accounting
• SSL v1/2/3
• Port security (Up to 64 MAC addresses per port)
• IP-MAC-Port Binding (IMPB)
- ARP inspection
- IP inspection
- IPv6 DHCP snooping
• Broadcast/Multicast/Unicast storm control
• 802.3ah Ethernet Link OAM
- Supports 802.3ah link layer remote loopback and discovery
(System log and SNMP)
- 802.3ah D-Link extension: D-link Unidirectional Link
Detection (DULD), (System log and SNMP)
• Command Line Interface (CLI)
• Telnet Server/Client (Support IPv4/IPv6)
• TFTP client (IPv4)
• Command logging
• SNMP v1/v2c/v3
• SNMP traps
• System log
• RMON v1
• RMON v2
• LLDP
• BootP/DHCP client
• DHCP auto-configuration
• Text-editable config file
• TACACS+ accounting
• User account privilege (4 level user access)
• MAC-based access control
- Max. 512 entries when using local database
• Authentication for management access
- Local, RADIUS, TACACS+ database
• D-Link Safeguard Engine
• DHCP server screening
• DHCP client filtering
• BPDU attack protection
• DoS attack prevention
• Traffic segmentation
• Cable diagnostics
• Dying Gasp
• Supports optical transceiver digital diagnostics monitoring
(DDM)
• Trusted host
• DHCP relay (IPv4/IPv6)
- DHCP relay agent/local relay
- DHCP relay option 12, 18, 37, 38, 82
• PPPoE Circult-ID tag insertion
• Trap/alarm/log severity control
• CPU monitoring
• SNTP
• LLDP-MED (for PoE models only)
• Debug command
• Password recovery
• Password encryption
• Backdoor password
Page 6
DGS-1210/ME Series Metro Ethernet Switches
MIB • RFC1212 Concise MIB Definitions
• RFC1213 MIB II
• RFC1215 MIB Traps Convention
• RFC1065, 1151, 2578 MIB Structure
• RFC1493 Bridge MIB
• RFC1157, 2573, 2575, 2576 SNMP MIB
• RFC3418 SNMPv2 MIB
• RFC2819 RMON MIB
• RFC2021 RMONv2 MIB
• RFC1643, 1650, 2665 Ether-like MIB
IETF Standard • RFC768 UDP
• RFC791 IP
• RFC792 ICMPv4
• RFC2463, 4443 ICMPv6
IPv6 • RFC1981 Path MTU Discovery
• RFC2460 IPv6
• RFC2461, 4861 Neighbor Discovery
Redundant Power Supply (Non-PoE Models Only)
DPS-200A / DPS-500A
1
Redundant Power Supply
Optional SFP Transceivers
DEM-310GT 1000BASE-LX, Single-mode, 10 km
DEM-311GT 1000BASE-SX, Multi-mode, 500 m
• RFC2674 802.1p MIB
• RFC 2233 Interface Group MIB
• RFC 2618 RADIUS authentication client MIB
• RFC 2620 RADIUS accounting client MIB
• RFC3289 D-Link Zone Defense MIB
• RFC4022 MIB for TCP
• RFC4113 MIB for UDP
• PoE MIB
• DDP MIB
• LLDP-MED MIB
• RFC793 TCP
• RFC826 ARP
• RFC1321, 2284, 2865, 2716, 3580 Extensible Authentication
Protocol (EAP)
• RFC2462, 4862 IPv6 Stateless Address Auto-configuration
• RFC2893, 4213 IPv4/IPv6 dual stack function
DEM-312GT2 1000BASE-SX, Multi-mode, 2 km
DGS-712 1000BASE-T 100 m (only supports 1000 Mbps mode) (no Flow Control)
1
Requires DPS-CB150-2PS, available by project request only.
2
All Gigabit Ethernet ports of the DGS-1210/ME Series switches support up to 6 kV surge protection.
Please note that the latest rmware for the DGS-1210-28/ME B1 (v7.00) is not backwards compatible with A1 hardware.
For more information: www.dlink.com
D-Link European Headquarters. D-Link (Europe) Ltd., First Floor, Artemis Building, Odyssey Business Park, West End Road, South Ruislip HA4 6QE, United Kingdom.
Specications are subject to change without notice. D-Link is a registered trademark of D-Link Corporation and its overseas subsidiaries.
All other trademarks belong to their respective owners. ©2017 D-Link Corporation. All rights reserved. E&OE.
Updated July 2017
Loading...