Regular Analog Setting Instructions
Note: Your model may not feature
a second hand or day/day-date feature
Caution
Before using the watch, READ this instruction manual carefully for safe and correct use. After reading this manual, keep it properly for your future reference.
SAFETY PRECAUTIONS (Please observe at all times)
In order to prevent injury to yourself or other persons and damage to property, this manual describes the instructions that you should strictly follow as follows. ■ Injuries and damages which might be caused by using the watch improperly, neglecting any of the instructions or precautions in this manual are classified with the following symbols.
Warning Can cause serious injury or death Caution Can or will cause minor or moderate
injury or damage
SPECIFICATIONS
1.Quartz oscillation frequency: 32,768Hz (Hz = number of vibrations per second)
2.Converter: Step motor
3.Additional functions: Calendar quick setting function (applies to watches equipped with day as well as day and month calendar functions)
4.IC (integrated circuit): 1C/MOS-LSI
5.Accuracy: within ±◊ 15 to 20 seconds
per month at normal temperature (+5°C≈ +35°C))
6. Battery: One silver oxide
CAL |
1010 |
1020 |
1030 |
1110 |
3220 |
4520 |
461* |
4633 |
464* |
Accuracy |
20 |
20 |
20 |
20 |
20 |
15 |
20 |
20 |
20 |
Battery |
|
|
|
|
|
|
|
|
|
Life |
3 |
5 |
3 |
3 |
3 |
2 |
2 |
2 |
2 |
CAL |
4713 |
477* |
5421 |
5431 |
5500 |
5510 |
5530 |
5920 |
5930 |
Accuracy |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
Battery |
|
|
|
|
|
|
|
|
|
Life |
3 |
2 |
3 |
2 |
5 |
5 |
5 |
2 |
2 |
CAL |
6010 |
6020 |
6031 |
604* |
6115 |
6790 |
7630 |
9620 |
9630 |
Accuracy |
20 |
20 |
20 |
20 |
20 |
20 |
30 |
20 |
20 |
Battery |
|
|
|
|
|
|
|
|
|
Life |
3 |
3 |
3 |
3 |
3 |
3 |
2 |
2 |
2 |
SETTING INSTRUCTIONS
1. Setting the Time and Date
(1)Stop the second hand in the “0 seconds” position by pulling out the crown to 2 then turn crown to set watch hands to the correct time. In case of a screw lock-type crown, place in position 2 after unlocking the screw.
(2)After setting watch to the correct time and returning crown to the 0 position, the second hand will be activated and the watch will commence to keep accurate time.
Due to the mechanical structure of the watch, the step position of the second hand is not aligned with the scale on the face. This does not have an
effect on the accuracy, however. Note:
a.To achieve optimal precision when setting the minute hand, move the minute hand four to five minutes past and then back to the desired setting.
b.For calendar-equipped watches, do not confuse AM and PM settings.
c.For watches equipped with locking screw-type crowns, do not forget to return the crown to the locked position after setting watch.
2. Setting the calendar
(1)Pull out crown to position 1
(2)Set date by turning crown to the left.
(3)Set day by turning crown to the right.
*For watches equipped with date display only, date is set by turning crown to the right.
(4)Return crown to 0 position.
Note:
Avoid performing the calendar quick setting operation between the below listed times:
For watches equipped with date display...9.00 PM- 1:00 AM
For watches equipped with both date and day display...9:00 PM-4:30 AM
If the calendar quick setting operation is performed between these times the calendar could be incorrectly set to the date of the previous day. After setting watch hands during these times, set time, day and date accordingly.
The above specifications are subject to change without prior notification.
Loading...