Breville BES400XL Manual

0 (0)

BR7804 BES400XL Book USA.qxp 20/6/06 1:14 PM Page a

Breville is a registered trademark of Breville Pty. Ltd.

Breville Customer Service Centre

US Customers

19400 S. Western Ave Los Angeles

CA 90501-1119

Service Centre: 1 (866) BREVILLE

Email askus@brevilleUSA.com

www.breville.com

Canada Customers

Anglo Canadian 2555, avenue Aviation

Pointe-Claire (Montréal) Québec

H9P 2Z2

Service Centre: 1 (866) BREVILLE

Fax	(514) 683-5554
Email	askus@breville.ca

www.breville.com

Due to continual improvements in design or otherwise, the product you purchase may differ slightly from the one illustrated in this booklet.

Model BES400XL Issue 1/06 Packaging Code: AM / CN

Ikon®

Espresso Machine

Instructions for use

Model BES400XL

BR7804 BES400XL Book USA.qxp 20/6/06 1:14 PM Page 2

Contents

	Page
Breville recommends safety first	4
Know your Breville Ikon Espresso Machine	6
Operating your Breville Ikon Espresso Machine	8
Coffee making tips	13
Care and cleaning	14
Trouble shooting chart	17
Coffees to try	18
French	F1
Spanish	S1

Congratulations

on the purchase of your new Breville Ikon Espresso Machine

BR7804 BES400XL Book USA.qxp 20/6/06 1:14 PM Page 4

Breville recommends safety first

IMPORTANT SAFEGUARDS

We at Breville are very safety conscious. We design and manufacture consumer products with the safety of you, our valued customer foremost in mind. In addition we ask that you exercise a degree of care when using any electrical appliance and adhere to the following precautions.

READ ALL INSTRUCTIONS AND SAVE

THESE FOR FUTURE REFERNCE

•Carefully read all instructions before operating and save for future reference.

•To protect against fire, electrical shock and injury to persons do not immerse the appliance, cord or plug in water or any other liquid.

•This appliance is for household use only.

•Do not use this appliance for anything other than its intended use.

•Close supervision is necessary when any appliance is used by or near children.

•Do not leave the appliance unattended when in use.

•Do not touch hot surfaces. Use handles.

•Always use the appliance on a dry, level surface.

•To disconnect, turn all controls to ‘OFF’, then remove plug from power outlet.

•Do not place this appliance on or near a hot gas or electric burner, or where it could touch a heated oven.

•Do not let the cord hang over the edge of a table or counter, touch hot surfaces or become knotted.

•The use of accessory attachments not recommended by Breville may cause a risk of injury to persons, fire or electric shock.

•Strictly follow cleaning and care instructions.

•Do not use this appliance for anything other than its intended use. Do not use in moving vehicles or boats. Do not use outdoors.

•Always switch the appliance to ‘OFF’, and then remove plug from the power outlet when the appliance is not being used and before cleaning.

•An extension cord is not recommended, however, if one is needed, the extension cord should be a grounded type and its electrical rating must be the same or more wattage as the appliance. Regularly inspect the supply cord, plug and actual appliance for any damage. If found damaged in any way, immediately cease use of the appliance and call Breville Customer Service at 1-866-BREVILLE.

•For any maintenance other than cleaning, call Breville Customer Service at 1-866-BREVILLE.

•Refer servicing to qualified personnel.

•This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way.

•Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or has been damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or adjustment.

•Save these instructions.

SPECIAL SAFETY INSTRUCTIONS

•Only use cold water in the water tank. Do not use any other liquid.

•Never use the machine without water in it.

•Ensure the filter holder is firmly secured when using the machine.

•Never remove the filter holder during the brewing operation as the machine is under pressure.

Your Breville appliance comes with the unique Assist™ Plug, conveniently designed with a finger hole in the power plug, for easy and safe removal from the outlet. For safety reasons it is recommended you plug your Breville appliance directly into the power outlet. Use in conjunction with a power strip or extension cord is not recommended.

Note

ELECTRIC CORD STATEMENT

Your Espresso Machine has a short cord as a safety precaution to prevent personal injury or property damage resulting from pulling, tripping or becoming entangled with the cord. Do not allow children to be near or use this appliance without close adult supervision. If you must use a longer cord or an extension cord when using the appliance, the cord must be arranged so it will not drape or hang over the edge of a countertop, tabletop or surface area where it can be pulled on by young children or tripped over. To prevent electric shock, personal injury or fire, the electrical rating of the extension cord if you must use one must be the same or more than the wattage of the appliance (wattage is marked on the underside of the appliance).

SAVE THESE INSTRUCTIONS FOR HOUSEHOLD USE ONLY

BR7804 BES400XL Book USA.qxp 20/6/06 1:14 PM Page 6

Know your Breville Ikon Espresso Machine

Italian designed and made 15 bar pump

Electronic touch control functions

Stainless steel boiler heating system

Advanced dual wall crema system

Removable

2 litre water tank

Extra large cup height,

ideal for coffee mugs

Specialised cleaning tools

provided with handy storage tray

Removable drip tray

catches any coffee spills for easier cleaning

Premium stainless steel design

Extra large cup warming plate

Variable steam control dial

Commercial size swivel steam wand

1 and 2 cup filters

Pre-brew function

Froth enhancer

for easier frothing and steaming of milk

Stainless steel frothing jug and measuring/tamping spoon included

Water level indicator

prevents overflow from drip tray

Assembling your Breville Ikon Espresso Machine

Your Ikon Espresso Machine will have the Drip Tray, Storage Tray and Water Tank in place when you unpack it from the box. The stainless steel coffee filters and the Cleaning Tools will be packed in a plastic sleeve with the jug in a box. The Filter Holder and Tamping/Measuring Spoon will be packed inside the foam packaging. Ensure you have located all parts and accessories before throwing out the packaging. Remove the Drip Tray and Water Tank and wash

all parts and accessories in warm, soapy water using a non-abrasive washing liquid. Rinse and dry thoroughly.

To reassemble

Insert the Storage Tray into the base of the machine and slide in towards the back wall (Fig 1). This is a convenient location to store the Cleaning Tool, stainless steel Filters and Measuring/tamping Spoon when not in use, so they are not misplaced.

Slide the Drip Tray, with the Drip Tray Full Indicator and Grid in place, into the base of the machine in front of the Storage Tray (Fig 2).

Slide the Water Tank over the Drip Tray and into the front opening of the machine and into position above the Storage Tray (Fig 3). Ensure the Water Tank aligns flush with the sides of the machine.

BR7804 BES400XL Book USA.qxp 20/6/06 1:14 PM Page 8

Operating your Breville Ikon Espresso Machine

BEFORE USING YOUR ESPRESSO MACHINE - PRIMING

To ensure that the boiler heating system and all internal piping has been preheated, it is essential to prime the machine before first use.

•Fill water tank with water to ‘MAX’ marking line.

•Switch machine on and direct the steam wand into the drip tray.

•Turn the steam dial on the side of the machine towards the ‘MAX’ position

•Press button and hold down until there is a solid stream of water exiting from the wand. At this

stage, release button and turn the Steam Dial to the ‘OFF’ position.

•After approx 1.5-2 minutes all 3 buttons will illuminate. Your Ikon Espresso Machine is now primed and ready for use.

After steaming or when the water tank runs dry, the Ikon Espresso Machine may not pump water through the shower filter. If this happens turn the machine off. Turn the steam dial on the side of the machine towards the 'MAX' position, with the steam wand directed back into drip tray until steam stops. Turn the Machine On and repeat priming procedure as outlined above.

Step 1 - Filling the water tank

•Remove the Filter Holder if locked into the Brew Head and move the Steam Wand to the side of the machine.

•Remove the water tank by pulling out of the front of the machine (Fig 4).

•When the water tank is removed, a rigid tube rotates and extends out of from the water tank area. Do not touch or try to remove this tube, it will automatically slide back into place once the water tank is reinserted.

•Fill with cold water to the maximum mark and replace back into the machine, pressing firmly so that the water tank clicks into position.

The water tank should be filled with fresh cold water before use. Check water level before use and replace the water daily or when water level indicated is below 750 ml. Do not operate if the water level is below 500ml. Do not use mineral water.

Note

Step 2 - Preparing the coffee

•Place the 1 or 2 cup filter into the filter holder and fill with ground espresso coffee (Fig 5). Use the single filter for 1 cup and the double filter for 2 cups.

•Use the measuring/tamping spoon provided to measure 1 level measure of espresso coffee for the single filter and 2 level measures for the double filter. It is important to use the correct amount of ground coffee for each filter.

Step 3 – Tamping the coffee

•Distribute the coffee evenly and press down firmly with the tamping end of the measuring spoon (Fig 6). If there is too much coffee, the flow of water can become blocked.

•Clean any excess coffee from the rim of the filter holder to ensure a proper seal under the brew head.

Step 4 – Priming the Brew Head

•Before placing the Filter Head into position, it is recommended to run a short flow of water through the Brew Head.

•Plug the power cord into a 120V power outlet and switch on. Press the button and the button surround will illuminate. The

button will flash on and off while the machine is heating. When the correct temperature has been reached, all 3 buttons will illuminate.

•Prime the Brew Head by pressing the button and hold down until water flows from the shower

filter. Release the button once the water has run through the Brew Head. A pumping noise will be heard during this operation.

Pre-warming the cups

The cup warming plate will start to warm as the machine heats. Pre-warm the espresso cups by placing them on the cup warming plate.

This will help maintain the coffee’s optimal temperature when brewed into the cups.

That’s the idea™

Step 5 – Inserting the Filter Holder

•Place the Filter Holder underneath the Brew Head so that the handle is positioned to the left of centre. Lift the filter holder until it contacts the brew head and rotate to the right until resistance is felt (Fig 7 & 8). Ensure handle is rotated as far as possible to the right to ensure a proper seal. Not rotating the handle sufficiently can result in the filter holder becoming detached during brewing.

BR7804 BES400XL Book USA.qxp 20/6/06 1:14 PM Page 10

Operating your Breville Ikon Espresso Machine continued

Step 6 - Brewing the coffee

•The 3 function buttons will illuminate once the machine has reached the correct temperature.

•Ensure the drip tray is in place.

•Place one or two pre-heated cups beneath the filter holder outlet.

•Press the button momentarily.

•After a few seconds*, aromatic coffee will begin to brew into the cups. A pumping noise will be heard in this operation.

*Pre-brew function

When the button is pressed momentarily, the boiler heating system pumps water briefly, followed by a pause, then continues to pump the water through to the ground coffee in the Filter Holder. This pre-brew function is an advanced feature of the Ikon Espresso Machine. The ground coffee is moistened by a small amount of water before full extraction. The ground coffee expands and when greater pressure is built up, the brewed coffee is extracted with its full flavour. To skip this function when brewing coffee, hold down the button, rather than pressing momentarily.

•When sufficient coffee has flowed into the cups,

press the button again. This will stop the flow of coffee. Twenty seconds is generally sufficient to pour two 30 ml espresso shots. It is not recommended to operate the brew function for a longer period at one time.

•If the steam function is not required, press the power button to switch off, switch off at the power outlet, unplug the power cord and allow the machine to cool.

Step 7 – Emptying the Filter Holder

•Remove the Filter Holder from the Brew Head by turning the Filter Holder to the left until it releases. Turn the Filter Holder upside down to empty the used coffee (used coffee grounds should be thrown away with domestic waste and not down the sink which may block drains). Remove the filter by pressing the ‘Eject’ Button on the underside of the Filter Holder (Fig 9). Rinse both the filter and filter holder with water and allow to dry.

The machine remains ready for brewing and maintains a constant heating temperature whilst the Power button is illuminated.

Note

THE METAL PARTS OF THE FILTER HOLDER MIGHT STILL BE VERY HOT. ALWAYS COOL THE FILTER HOLDER WITH COLD WATER BEFORE ATTEMPTING TO REMOVE FILTERS.

How to froth milk for a cappuccino or latté

The Breville Ikon Espresso Machine comes complete with a Froth Enhancer for easier frothing of milk. When less froth is required, remove the Froth Enhancer and steam the milk using the Steam Wand. To remove the Froth Enhancer, ensure it is cool then simply pull down and remove (Fig 10). The Frothing Attachment can be stored in the Storage Tray inside the machine if not used regularly.

To refit the Froth Enhancer, ensure it is securely attached to the Steam Wand by inserting it, from either end opening, onto the Wand and pushing it firmly upwards onto the rubber surround (Fig 10).

The first step in making a cappuccino/latté is to make a short espresso (Follow steps on “Brewing Coffee” on page 9). Then:

•Fill the stainless steel frothing jug 1⁄3 full with cold milk.

•Press the button momentarily and direct steam wand into drip tray. Turn the steam control dial on the side of the machine towards the ‘MAX’ position.

This will drain any residual water before the boiler begins to generate steam. The light will start to flash indicating that the Boiler Heating System is heating and preparing to create steam.

Although not essential, for maximum steaming pressure it is recommended to wait approximately 30 seconds for light to stop flashing before turning the steam control dial towards the ‘MAX’ position.

Note

•Turn Steam Control Dial to the ‘OFF’ position, insert the steam wand into the milk jug and then turn the Steam Control Dial towards the ‘MAX’ position (Fig 11).

•Gently move the frothing jug in a circular motion around the froth enhancer.

The Ikon Espresso Machine features a Swivel Steam Wand so the position of the Steam Wand can be changed to a comfortable angle.

That’s the idea™

•When the milk has begun to increase in volume, immerse the froth enhancer deeper into the milk to further heat the milk.

•Place your hand on the bottom of the stainless steel frothing jug.

•When using the Steaming function, is the thumping noise normal? Yes, the thumping noise is the 15 bar pump in operation.

BR7804 BES400XL Book USA.qxp 20/6/06 1:14 PM Page 12

Operating your Breville Ikon Espresso Machine continued

•When the jug becomes too hot to touch, turn the

steam control dial to the ‘OFF’ position and then press the button to stop the steaming function before removing the jug.

Steam Control Dial should always be positioned in the ‘OFF’ position when steam is not required. Steam will automatically turn off after 3 minutes of steaming.

Note

•Pour the steamed milk to each cup of freshly brewed espresso coffee and spoon on the frothed milk in the following ratios:

Cappuccino - 1⁄3		espresso, 1⁄3 steamed milk,
	1⁄3	frothed milk
Latté -	1⁄3	espresso topped with steamed

milk and about 10cm of frothed milk (traditionally served in a glass)

•After each steaming operation direct the Steam Wand back into the Drip Tray. Turn the Steam Control Dial towards the ‘MAX’ position and press

the button and hold down until a solid stream of water exits from the Steam Wand.

Always ensure that the Froth Enhancer has been firmly pushed onto the steam wand. For best results use fresh cold milk (lite milk will froth easier). Always clean the steam wand and froth enhancer immediately after every use (refer to care and cleaning).

Note

Standby Mode

As an energy saving feature, the Ikon Espresso Machine will go into ‘standby mode’ after a period of 60 minutes of total inactivity. The insert power symbol button will be the only button lit during this time. To reactivate simply press any of the

3 function buttons.

THE STAINLESS STEEL JUG PROVIDED WITH THIS PRODUCT IS INTENDED FOR FROTHING MILK ONLY. IT IS NOT INTENDED FOR DISPENSING HOT COFFEE.

LIQUID SHOULD NOT BE ALLOWED TO RUN OVER THE TOP OF THE FROTH ENHANCER, OTHERWISE IT WILL NOT FUNCTION.

TO AVOID SPLATTERING HOT MILK, DO NOT LIFT THE STEAM NOZZLE ABOVE THE SURFACE OF THE MILK WHILE FROTHING.

Coffee making tips

Making a good cup of coffee is an art that is simple to achieve. Here are some tips to help you make the perfect coffee.

To enjoy an optimum flavoured espresso coffee, do not extract more than approximately 30ml (using the 1 cup filter holder) or for a double espresso do not extract more than 60ml (using a 2 cup filter holder).

Note

The coffee

Pre-ground coffee can be used and should be stored in an air-tight container, in a cool, dry area. Pre-ground coffee should not be kept for longer than 1 week as flavour will diminish. Do not refrigerate or freeze.

Whole coffee beans, freshly ground just before use, are recommended. Coffee beans should be stored in an air-tight container, in a cool, dry area but should not be kept for longer than 1 month as flavour will diminish. Do not refrigerate or freeze.

Water flow

When brewing coffee, make sure the water flows through the Coffee Filter at the correct rate.

If the water flow is too slow the coffee will be over extracted and will be very dark and bitter, with a mottled and uneven crema on top.

If the water flow is too fast, the coffee will be under extracted – the optimal flavour will not develop, the coffee will be watery and lack the thick crema on the top.

The water flow can be adjusted by varying the pressure that the coffee is tamped (pressed down) in the Filter or by changing the grind of the coffee.

The grind

If using a pre-ground coffee, ensure an espresso grind suitable for espresso/cappuccino machines is purchased. If grinding coffee beans, the grind should be fine but not too fine or powdery. The grind will effect the rate at which the water flows through the coffee in the Filter and therefore the taste of the coffee.

If the grind is too fine (looks like powder and feels like flour when rubbed between fingers), the water will not flow through the coffee even when under pressure. The resulting coffee will be over extracted, too dark and bitter, with a mottled and uneven crema on top.

If the grind is too coarse the water will flow through the coffee too quickly. This will result in an under-extracted coffee lacking in flavour and without the thick crema on the top layer of coffee.

Tamping the coffee

After measuring the ground coffee into the Filter it must be tamped (pressed down) using the flat end of the measuring spoon. The ground coffee should be tamped quite firmly.

If the coffee is not tamped firmly enough, the water will flow through the water too quickly and the coffee will be under extracted. If the coffee is tamped too firmly, however, the water will flow through the coffee too slowly and the coffee will be over extracted.

The taste of your coffee will, of course, depend on personal preference and on many other factors such as the type of coffee bean used, the coarseness or fineness of the grind and the tamping pressure (pressed down). We recommend experimenting by varying

these factors to achieve the coffee taste of your preference.

Note

BR7804 BES400XL Book USA.qxp 20/6/06 1:14 PM Page 14

Care and cleaning

Before cleaning, ensure the machine has been turned off. Switch off at the power outlet, unplug the power cord and allow the machine to cool.

Cleaning the steam wand and froth enhancer

•The Steam Wand and Froth Enhancer should always be cleaned immediately after frothing milk. Never leave Steam Wand immersed in milk. This ensures the Steam Wand is kept free of milk deposits.

Failure to do this may result in milk being sucked back into the boiler heating system.

•Remove the Froth Enhancer and rinse under warm tap water (Fig 10) page 11.

•Wipe the steam wand with a damp cloth. If the steam wand becomes blocked, use the pin on the Cleaning Tool to clear the opening. If the Steam Wand is not wiped with a damp cloth immediately after use milk deposits will bake onto the surface and become harder to remove. If this occurs it is recommended to soak the Steam Wand before wiping with a damp cloth.

DO NOT USE a scourer or abrasive cleaner to clean Steam Wand or housing.

Note

If the Steam Wand remains blocked, the tip of the Steam Wand can be removed by using the spanner in the middle of the Cleaning Tool (Fig 12). Soak the tip in hot water before using the pin on the Cleaning Tool to unblock (Fig 13).

Replace the tip back onto the Steam Wand and secure with the Cleaning Tool.

Cleaning the filters, filter holder and brewing head

•The stainless filters and filter holder should be rinsed under running water directly after use to remove all coffee particles. Should the fine holes in the filters become blocked, the fine pin on the Cleaning Tool can be used to clear the holes (Fig 14).

•The brewing head should be wiped with a damp cloth to remove any residual coffee grounds.

•It is advisable to periodically run water through the machine with the filter holder in place, but without any coffee to clean out any residual coffee grounds.

Cleaning the shower head

•To eliminate coffee grinds from the shower

head, simply unscrew using the allen key provided and rinse under hot water. Replace using the allen key (Fig 15) ensuring the fixing screw is firm but not over tightened.

Cleaning the housing/cup warming tray

•The outer housing and cup warming tray can be cleaned with a soft, damp cloth (do not use

abrasive cleansers, pads or cloths which can scratch the surfaces).

Cleaning the drip tray

•The Drip Tray should be removed, emptied and cleaned at regular intervals, particularly when the water level indicator is exposed indicating the drip tray is full (Fig 16).

•Remove the grid and water level indicator from the drip tray and wash all three parts in warm water using a non-abrasive washing liquid. Rinse and dry thoroughly.

Cleaning the storage tray

•The Storage Tray can be removed after the Drip Tray is removed and cleaned with a soft, damp cloth (do not use abrasive cleansers, pads or cloths which can scratch the surface).

Decalcifying

After regular use, hard water can cause mineral build up in and on many of the inner functioning components, reducing the brewing flow, power of the machine, and affecting the quality of coffee.

We advise decalcifying the machine on a regular basis (every 2-3 months) using either a commercial decalcifying agent formulated specially for boiler espresso machines, or a mixture of white vinegar and water.

Do not use powered decalcifying agents.

Note

Use the following as a guide:

Diluted solution (for softer water)

•1 part white vinegar

•2 parts cold tap water

Concentrated solution (for harder water)

•1 part white vinegar

•1 part cold tap water

DO NOT IMMERSE ANY PART OF YOUR IKON ESPRESSO MACHINE IN WATER OR ANY OTHER LIQUID. THE WATER TANK SHOULD NEVER BE REMOVED OR COMPLETELY EMPTIED DURING DECALCIFYING.

BR7804 BES400XL Book USA.qxp 20/6/06 1:14 PM Page 16

Care and cleaning continued

Decalcifying the machine

•Ensure the machine is switched off and that the plug is disconnected from the power outlet.

•Remove the Filter Holder and Froth Enhancer. Pour the decalcifying solution into the water tank.

•Plug the machine into the power outlet and turn on.

•Press power button to turn the machine on.

•Place a large container under both the Brew Head and the Steam Wand.

•As soon as the brewing temperature is reached the

3 function buttons will illuminate. Press the button on and allow half the decalcifying solution run through the Brew Head.

•Turn the Steam Control Dial to the ‘MAX’ position

and press the button and allow the remaining solution to run through the Steam Wand. When the

solution has stopped flowing, press the button, turn the Steam Control Dial to ‘OFF’.

•After decalcifying, remove the Water Tank and rinse thoroughly then refill to maximum line with fresh cold water. To rinse the machine, run half the water through the Brew Head and half through the Steam Wand.

•Fill with fresh, cold water.

•The machine is ready for use.

Trouble shooting chart

Problem	Possible causes

Coffee does not run through	•	Machine is not turned on or plugged in
	•	Water tank is empty
	•		Button has not been pressed
	•	Coffee grind is too fine
	•	Too much coffee in the filter
	•	The filter is blocked

Coffee runs out too quickly	•	Coffee grind is too coarse
	•	Not enough coffee in the filter

Coffee runs out around the	•	Filter holder is not inserted in the brew head properly
edge of the filter holder	•	There are coffee grounds around the filter rim
	•	Too much coffee in the filter
	•	Coffee has been tamped too tightly

Coffee filters out in drops	•	The water tank is empty or low
	•	Coffee grind is too fine
	•	Machine is blocked by mineral deposits

The machine has loud	•	Water tank is empty or low
pumping noise	•	Water tank is not securely in place

Coffee is too weak or watery	•	Coffee grind is not fine enough
		(use coffee ground for espresso machines)

Coffee is too cold	•	Machine not preheated
	•	Cups not preheated
	•	Milk not heated enough (if making a cappuccino or latté)

No crema	•	Coffee is not tamped firmly enough
	•	Coffee grind is too coarse
	•	Coffee is not fresh

No steam is generated	•	Machine is not turned on
	•	Water tank is empty
	•		Button has not been pressed
	•	Steam Control Dial has not been turned towards ‘MAX’ position
	•	Steam wand is blocked

Milk is not foamy	•	Not enough steam
after frothing	•	Milk is not fresh and cold

BR7804 BES400XL Book USA.qxp 20/6/06 1:14 PM Page 18

Coffees to try

Espresso

Intense and aromatic, an espresso or short black as it’s also known uses about 7g of ground coffee. It is served in a small cup or glass to a level of approximately 30ml.

Long black

A long black is generally served as a standard espresso with hot water added to taste.

Flat white

A single dose of espresso in a cup topped with steamed milk, 1⁄3 coffee and 1⁄3 milk.

Cappuccino

The real thing is served very light and luke warm with

1⁄3 espresso to 1⁄3 steamed milk and a generous final third of creamy froth. For added finesse, hold a piece of card over one half of the the cappuccino before dusting with chocolate.

Macchiato

A shot of espresso served short in a 70ml demitasse and stained with a dash of finely frothed milk.

Classic cafe latté

Traditionally the morning coffee of Italy and France, taken with pain au chocolate or sweet biscotti. This blend of 1⁄3 espresso to 2⁄3 milk is made with a single shot of espresso. Top with steamed milk, poured down the inside rim of the glass to give a creamy consistency and perfect layer of froth.

Espresso affagato

Totally irresistible, this sweet temptation is simply a single scoop of premium vanilla bean ice cream, drenched in espresso and if desired, your favourite liqueur. To create a sense of occasion, serve ice cream in a martini glass with shots on the side.

Con panna

Meaning ‘with cream’ this heart warmer is a chic variation on oldfashioned Vienna Coffee. In a 90-120ml cup, dress a double shot of espresso with a dollop of fresh cream, whipped until glossy. Dust with cinnamon and serve immediately.

Mocha frappe (serves two)

Ready in minutes this impressive refresher will delight chocolate and coffee drinkers alike. Melt two heaped teaspoons of quality chocolate bits into a double shot of espresso. Add 1⁄2 cup cold milk and 9 ice cubes and process in blender on a low speed to a smooth, velvety consistency. Pour evenly into two glasses and serve immediately.

BR7804 BES400XL Book USA.qxp 20/6/06 1:14 PM Page 20

One year limited warranty

Breville®* warrants this Breville® appliance against defects that are due to faulty material or workmanship for a period of one (1) year from the date of original consumer purchase. This warranty does not cover damage from abuse, neglect, use for commercial purposes, or any other use not found in the printed “Instructions for use” booklet. There is no warranty for glass parts, glass containers, filter basket, blades and agitators. HWI Breville® expressly disclaim all responsibility for consequential damages for incidental losses caused by use of this appliance. Some states or provinces do not allow this exclusion or limitation for incidental or consequential losses, so the foregoing disclaimer may not apply to you.

ANY WARRANTY OF MERCHANTABILITY OR FITNESS WITH RESPECT TO THIS PRODUCT IS ALSO LIMITED TO THE ONE YEAR LIMITED WARRANTY PERIOD. Some states or provinces do not allow disclaimer of the implied warranty with respect to consumer goods, so the foregoing disclaimer may not apply to you.

This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state or province to province.

If the appliance should become defective within the warranty period, do not return the appliance to the store. Please contact our Customer Service Center.

Toll free phone number: 1-866-BREVILLE (1-866-273-8455)

Internet email:

AskUs@BrevilleUSA.com

AskUs@Breville.ca (in Canada)

*HWI Breville® products are distributed in Canada by Anglo Canadian Housewares, L.P. and in USA by Metro/Thebe Inc.

Notes

+ 23 hidden pages