Thank you for choosing our product. We hope you will enjoy using the appliance.
Symbols in these Instructions for Use
Symbols in these Instructions for Use
Symbols in these Instructions for UseSymbols in these Instructions for Use
Important information for your safety is specially marked. It is essential to comply with these instructions in
order to avoid accidents and prevent damage to the machine:
WARNING:
WARNING:
WARNING:WARNING:
This warns you of dangers to your health and indicates possible injury risks.
CAUTION:
CAUTION:
CAUTION:CAUTION:
This refers to possible hazards to the machine or other objects.
NOTE
NOTE:::: This highlights tips and information.
NOTENOTE
General Notes
General Notes
General NotesGeneral Notes
Read the operating instructions carefully before putting the appliance into operation and keep the instructions
including the warranty and the receipt. If you give this device to other people, please also pass on the operating instructions.
NOTE
NOTE:::: The illustrations in this instruction manual can deviate from the original appliance.
NOTENOTE
• The appliance is designed exclusively for private use and for the envisaged purpose. This appliance is not
fit for commercial use.
• The appliance is only to be used as described in the user manual. Do not use the appliance for any other
purpose. Any other use is not intended and can result in damages or personal injuries.
• Operate the appliance only pr
properly installed
operly installed.
prpr
operly installedoperly installed
• Do not use it outdoors. Keep it away from sources of heat, direct sunlight and humidity.
• Do not operate the appliance without
without supervision.
withoutwithout
• When not in use, for cleaning, user maintenance works or with disruption, switch off the appliance and
disconnect the plug (pull the plug itself, not the lead) or turn off the fuse.
• The appliance and if possible the mains lead have to be checked regularly for signs of damage. If damage
is found the appliance must not be used.
• For safety reasons, alterations or modifications of the appliance are prohibited.
• In order to ensure your children’s safety, keep all packaging (plastic bags, boxes, polystyrene etc.) out of
their reach.
WAR
WARNING
NING::::
WARWAR
NINGNING
Do not allow small children to play with the foil. There is a dange
3
danger of suffocation!
r of suffocation!
dangedange
r of suffocation!r of suffocation!
Special safety Information for this Unit
Special safety Information for this Unit
Special safety Information for this UnitSpecial safety Information for this Unit
• The maximum number of place settings to be washed is 14.
• This unit is intended to be used in household and similar applications such as
- staff kitchen areas in shops, offices and other working environments;
- by clients in hotels, motels and other residential type environments;
- in farm houses.
• The appliance is to be connected to the water mains using new hose sets and that
old hose-sets should not be reused.
• The maximum permissible inlet water pressure is 1 Mpa.
• The minimum permissible inlet water pressure is 0.04 Mpa.
• In the appliance bottom are located ventilation openings (depending on model).
These may not be clogged e.g. by carpet.
• Pay attention to a proper loading of the appliance. Follow the instructions in the
chapter “Loading the Dishwasher Baskets”.
• Knives and other utensils with sharp points must be loaded with their points down
in the cutlery basket (depending on model) or placed in a horizontal position in the
dishwasher basket.
• The door should not be left open, since this could increase the risk of tripping.
• This appliance can be used by children
children aged from 8 years and above and persons
childrenchildren
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of
the appliance
the appliance in a safe way and understand the hazards involved.
the appliancethe appliance
• Children
Children who are younger than 8 years must be kept away from the device.
ChildrenChildren
• Children
Children shall not play with the appliance.
ChildrenChildren
• Cleaning and user
user maintenance
maintenance shall not be made by children,
useruser
maintenancemaintenance
children, unless they are
children,children,
use of
use of use of
older than 8 years and are supervised.
• Do not try to repair the appliance on your own. Always contact an authorized
technician. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
4
Unpacking the Appliance
Unpacking the Appliance
Unpacking the ApplianceUnpacking the Appliance
• Remove the appliance from its packaging.
• Remove all packaging material, such as foils, filler and cardboard packaging.
• To prevent hazards, check the appliance for any transport damage.
• In case of damage, do not put the appliance into operation. Contact your distributor.
NOTE
NOTE::::
NOTENOTE
Production residue or dust may have collected on the appliance. We recommend cleaning the appliance according to chapter “Cleaning and Maintenance”.
Appliance
Appliance
Appliance overview
Appliance Appliance
overview
overviewoverview
Appliance Equipment
ApplianceAppliance
Equipment
EquipmentEquipment
1 Upper spray arm
2 Cutlery rack
3 Upper basket
4 Inner water pipe
5 Lower basket
6 Salt container (water softener)
7 Detergent / rinse aid dispenser
8 Cup shelf
9 Lower spray arm
Delivery scope
Delivery scope
Delivery scopeDelivery scope
10 Filter system
cub shelf (2 pcs), salt funnel tube, dosing assistance for rinse aid and cleaning agent, installation material incl.
drilling template
Installation
Installation
InstallationInstallation
WARNING:
WARNING:
WARNING:WARNING:
The unit must not be connected to the mains during installing. Otherwise there is danger to life
shock ha
shock hazzzzard
shock hashock ha
CAUTION
CAUTION::::
CAUTIONCAUTION
ard!
ardard
danger to life or electric
danger to lifedanger to life
electric
electric electric
For a correct operation the appliance must be connected properly. The specifications for water supply and
drain as well as the electrical connection must fulfill the required criteria.
Installation location
Installation location
Installation locationInstallation location
• The site should be located near the water inlet and outlet, as well as near a properly grounded power
socket. Arrange a place in the cabinet under the sink for the cable and hoses.
5
• Consider the necessary installation dimensions (see “Installation steps”).
• Take care of a solid and horizontal position of the appliance. If the appliance is not horizontally leveled,
adjust the feet accordingly.
• Power cable and water hoses may not kinked or squashed.
• Avoid the installation:
Avoid the installation:
Avoid the installation:Avoid the installation:
- near heaters, next to a stove, direct sunlight or any other heat sources;
- at locations with high humidity (e.g. outdoors), as metal parts would be susceptible to corrosion under
such circumstances;
- in rooms where the temperature could drop below freezing. Do not expose the appliance any weather.
- near volatile or flammable materials (e.g. gas, fuel, alcohol, paint, etc.).
Installation steps
Installation steps
Installation stepsInstallation steps
Attach the condensation strip
Attach the condensation strip
Attach the condensation stripAttach the condensation strip
Attach the strip under the wooden worktop to prevent it from damages of ascending water vapor.
• First clean and dry the concerned area of the worktop thoroughly.
• Remove the protective foil from the condensation strip and stick it flush
with the worktop edge.
Cabinet opening and appliance d
Cabinet opening and appliance diiiimension
Cabinet opening and appliance dCabinet opening and appliance d
mension
mensionmension
Prepare the cabinet opening according to the dimensional drawing.
Unit: mm
If the appliance is installed at the corner of the cabinet, there must remain enough space to
open the door.
1 Kitchen furniture 2 Dishwasher 3 Appliance door
Unit: mm
Dimension and preparation of
Dimension and preparation of the decoration panel
Dimension and preparation of Dimension and preparation of
the decoration panel
the decoration panelthe decoration panel
Prepare the wooden decorative panel according to the dimensional drawing.
• Align the drilling template and mark the necessary holes.
Check this with a spirit level.
• Drill holes of Ø 2 mm and 8 mm depth at the pre-marked
positions in the panel.
Unit: mm
6
Fixing the decoration panel
Fixing the decoration panel
Fixing the decoration panelFixing the decoration panel
• Insert the brackets into the holes of the decorative panel and turn the screws in.
• Hook the decorative panel with the brackets into the provided slots on the appliance
front.
• Align the panel and the appliance front against each other and fix the panel on the
appliance door.
• First remove the factory-mounted short screws (4 x s1) from the door inside.
• Screw the supplied long screws (4 x s2).
Adjusting of the door spring tension
Adjusting of the door spring tension
Adjusting of the door spring tensionAdjusting of the door spring tension
After fixing the decoration panel, the door spring tension must be adjusted accordingly.
• Turn the adjusting screws as needed in the clockwise or counterclockwise
direction. The steel cable tightens or loosens.
• Check the door spring tension. If the door remains fully open horizontally
and can still be easily closed, the tension is correct. Otherwise do the adjusting again.
Connection to the water supply
Connection to the water supply
Connection to the water supplyConnection to the water supply
Connect the water inlet hose as well as the water drain hose properly. Follow the instructions that we give you
under "Water connection".
Installation to the power supply
Installation to the power supply
Installation to the power supplyInstallation to the power supply
Consider the instructions that we give you under "Electrical connection".
Adjusting the feet
Adjusting the feet
Adjusting the feetAdjusting the feet
Place the appliance in its proper position and take care that it is leveled solid and horizontal. Check this with a
spirit level.
• You can adjust the back foot by the adjusting screw (a) at the center of the
appliance plinth front with an Allen key.
• Adjust the front feet (b) with a screw-wrench until the dishwasher is leveled.
The maximum adjustment height of the feet is 50 mm.
Fixing the dishwasher
Fixing the dishwasher
Fixing the dishwasherFixing the dishwasher
Fix the appliance by tighten the screws from the appliance inside to the provided holes accordingly.
1111 If the worktop made of wood, fasten the appliance to the worktop.
2222 If the worktop made of marble or granite, fasten the appliance sideways with
the housing unit. Put the screw covers on.
7
Water connection
Water connection
Water connectionWater connection
CAUTION:
CAUTION:
CAUTION:CAUTION:
• The Installation of the water supply must conform to the local laws and regulations.
• Use the new supplied hose set to connect the appliance to the water supply. Do not reuse old or used
connection sets.
• If the water pipe is new or long time not used, ensure before connecting to the water system, that the water
is clear and free from contamination.
Notes
Notes on inlet hose safety system
on inlet hose safety system
Notes Notes
on inlet hose safety systemon inlet hose safety system
The safety system consists of a double-walled inlet hose. This system guarantees to cut off the water supply
when leakage of the inner hose. Switching off the water supply leads over an electronic contact.
Connect the water
Connect the water inlet
Connect the water Connect the water
NOTE
NOTE::::
NOTENOTE
The water pressure must be between 0.04 and 1 MPa. With higher pressure: use a pressure regulator.
inlet hose (cold water connection)
hose (cold water connection)
inletinlet
hose (cold water connection)hose (cold water connection)
• Connect the water inlet hose to a water thread with ¾“. Screw the hose firmly in the direction
of the screw thread; pay attention for a tight fit.
• Connect the other end of the inlet hose to the inlet valve on the appliance back; pay attention
for a tight fit too.
Hot water supply
Hot water supply
Hot water supplyHot water supply
The dishwasher can be supplied with a water temperature of not more than 60°C. Supplying the appliance
with hot water, the rinse running time is shortened but the cleaning effect can be slightly reduced. The connection to the hot water valve must be done in the same manner as described for the cold water connection.
Connect the water drain hose
Connect the water drain hose
Connect the water drain hoseConnect the water drain hose
NOTE
NOTE::::
NOTENOTE
The drain hose has a length of approx. 1.5 m and can extend with a suitable hose and connecting piece to a
length of max. 4 m.
CAUTION
CAUTION::::
CAUTIONCAUTION
In order to prevent backflow of contaminated water, the free end of the hose must not come under the water
level of the drain.
• Connect the drain hose to a drain pipe with a minimum diameter of Ø 40 mm;
alternatively the drain hose can be fixed directly to the sink.
• Always make sure that the hose is not bent or squeezed.
• It is allowed to install the hose maximal up to a height of 1000 mm above the
rinsing floor.
• Secure the drain hose securely to avoid a change in position and with it a
water leakage.
8
Electrical connection
Electrical connection
Electrical connectionElectrical connection
WARNING:
WARNING:
WARNING:WARNING:
• The installation to the mains supply must conform to the local standards and regulations.
• Improper connection may cause to an electric shock
electric shock!
electric shockelectric shock
• Do not use multiple sockets or extension cords.
• It is not allowed to modify the plug provided with the appliance. If the plug does not fit properly to the outlet,
let install a proper outlet by an authorized specialist.
• The accessibility of the power plug must always be ensured in order to disconnect the device from the
power supply in case of an emergency.
• Ensure that your mains power corresponds with the specifications of the appliance. The specifications are
printed on the rating label.
• Connect the mains cable to a properly installed and earthed wall outlet.
• If the plug after installation is not accessible, a corresponding disconnect device must be available to meet
the relevant safety regulations.
Prior Using for the first Time
Prior Using for the first Time
Prior Using for the first TimePrior Using for the first Time
Before using your dishwasher for the first time:
Before using your dishwasher for the first time:
Before using your dishwasher for the first time:Before using your dishwasher for the first time:
A. Filling salt into the salt container (water softener)
B. Fill the rinse aid dispenser
C. Fill in detergent
CAUTION:
CAUTION:
CAUTION:CAUTION:
• Use only salt, rinse aid and detergent for dishwashers. Other products may damage the appliance.
• Always consider the dosage and storage recommendations on the sales packaging.
WARNING:
WARNING:
WARNING:WARNING:
Keep salt, rinse aid and detergent out of reach for children.
AAAA. Filling salt into the salt container
. Filling salt into the salt container (water softener)
. Filling salt into the salt container. Filling salt into the salt container
Water softener
Water softener
Water softenerWater softener
(water softener)
(water softener)(water softener)
The water hardness varies regionally. If hard water is used in the dishwasher, deposits form on the dishes and
kitchen utensils. The appliance is equipped with a water softener, that removes lime and minerals from the
water by using water softening in the salt container. Your local water authority can advise you on the hardness
of the water in your area.
Adjusting the salt consumption
Adjusting the salt consumption
Adjusting the salt consumptionAdjusting the salt consumption
The salt consumption can be adjusted according to your water hardness and therefore optimally regulated.
• Open the appliance door and switch on the appliance using the power button.
• Use the MENÜ (menu) button to select the menu item [ADJ. SALT CONS].
9
• By pressing the buttons <<<< or >>>>, the water hardness can be changed accordingly. The display shows the
setting: [H1->H2->H3->H4->H5->H6]
• Finish the setup via the OK button. The water hardness is automatically saved.
The following settings (benchmarks) are recommended:
NOTE:::: *°dH: German degree / °fH: French degree / °Clark: British degree
NOTENOTE
Fill in the salt
Fill in the salt
Fill in the saltFill in the salt
CAUTION:
CAUTION:
CAUTION:CAUTION:
• Only refill the salt container when the corresponding message lights up in the display.
• During filling the salt container, salt and water can escape. Start a program immediately after you have
filled the container to prevent corrosion.
• Remove the lower basket and unscrew the lid of the salt container.
• Add about 1.5 kg of salt by using the supplied funnel tube.
• Full fill the salt container with water (just before the first use).
• Screw the lid firmly on again after filling the container.
• Depending on salt resolution, the message in the display disappears usually immediately after filling.
BBBB.
.
Fill the rinse aid dispenser
Fill the rinse aid dispenser
. .
Fill the rinse aid dispenserFill the rinse aid dispenser
Function of rinse aid
Function of rinse aid
Function of rinse aidFunction of rinse aid
The rinse aid is automatically added during the final rinse, ensuring thorough rinsing and a spot and streak
free drying.
When to refill the rinse aid dispenser
When to refill the rinse aid dispenser
When to refill the rinse aid dispenserWhen to refill the rinse aid dispenser
As long as the corresponding message does not light up in the display, you can estimate
the amount of remaining rinse aid to the optical level indicator "CCCC" next to the dispenser.
When the rinse aid dispenser is full, the indicator is completely dark. If the rinse aid diminishes, the size of
the black dot changes as shown below. In order to avoid spotting, the rinse aid level must not drop below ¼.
full ¾ full ½ full ¼ full – refill empty
10
Fill in the rinse aid
Fill in the rinse aid
Fill in the rinse aidFill in the rinse aid
• To open the dispenser screw the lid counterclockwise to the open posi-
tion (left arrow) and remove the lid.
• Add the rinse aid into the dispenser, being careful not to overfill.
The dispenser contains approx. 110 ml.
• Before closing the appliance door, put on the lid in the open position back and turn it clockwise to the
closed position (right arrow).
NOTE
NOTE::::
NOTENOTE
Remove spilled rinse aid with an absorbent cloth to avoid excessive foaming during the next rinse.
Adjusting the rinse aid dosage
Adjusting the rinse aid dosage
Adjusting the rinse aid dosageAdjusting the rinse aid dosage
When forming spots and the dishes dries poorly, increase the added amount of rinse aid. You can set the
amount of addition between level 1 (min.) and level 6 (max.).
Take off the lid of the rinse aid dispenser and adjust the dial to the desired level.
NOTE
NOTE::::
NOTENOTE
The factory setting is 4.
Increase the dosage if there are drops of water or lime spots on the dishes after rinsing. Reduce the dosage if
there are sticky whitish stains on dishes or a bluish film on glassware or knife blades.
CCCC.
. Fill in detergent
Fill in detergent
. .
Fill in detergentFill in detergent
Function of detergent
Function of detergent
Function of detergentFunction of detergent
Detergents with its chemical ingredients are necessary to remove dirt, crush dirt and transport it out of the
dishwasher. The most commercially, high-quality cleaning agents are suitable for this purpose.
Detergent
Detergent
DetergentDetergent
Normally new pulverized detergent is without phosphate. Thus the water softener function of phosphate is not
given. In this case we recommend to fill salt in the salt container even when the hardness of water is only
6°dH. If detergents without phosphate are used in the case of hard water often white spots appear on dishes
and glasses. In this case add more detergent to reach better results. Detergents without chlorine do only
bleach a little. Strong and colored spot will not be removed completely. In this case choose a program with a
higher temperature.
Detergent tablets (
Detergent tablets (TTTTabs
Detergent tablets (Detergent tablets (
abs))))
absabs
Dishwasher tablets from different manufacturers dissolve at different rates. It is possible that they will not fully
dissolve in programs with short running time and low water temperature and thus does not reach their full
productive efficiency. To ensure the complete removal of detergent residues, we recommend choosing rinse
programs with long running times and high water temperature. Always follow the manufacturer's instructions!
11
Fill in the detergent
Fill in the detergent
Fill in the detergentFill in the detergent
NOTE
NOTE::::
NOTENOTE
• Always add the detergent just before starting the rinse cycle, otherwise it could get damp and will not dis-
solve properly.
• You’ll find information about the amount of detergent for the respective programs in the „Rinse cycle table“.
Note that depending on the degree of soiling and water hardness differences are possible.
• At the end of the rinse cycle the detergent dispenser must be empty.
The dispenser must be refilled before the start of each rinse cycle according to the instructions in the "Rinse cycle table".
Press the release button to open the dispenser.
1111 Chamber of detergent in powder form for the main rinse
2222 Chamber of detergent for the pre-rinse / Chamber for detergent in tablet form
Add with heavily soiled dishes an additional dose of detergent in the chamber for the pre-rinse.
Close the dispenser. Make sure that the lid locks into place.
Loading the Dishwasher Baskets
Loading the Dishwasher Baskets
Loading the Dishwasher BasketsLoading the Dishwasher Baskets
CAUTION:
CAUTION:
CAUTION:CAUTION:
Only rinse such dishes and cutlery in the dishwasher, which is expressly marked as "dishwasher resistant".
NOTE
NOTE::::
NOTENOTE
• Remove gross scraps of food and soak burnt leftovers. Pre-rinse under running water is not necessary.
• Do not overload! This is important for adequate cleaning results and reasonable energy consumption.
• Very small items should not be rinsed in the appliance, as they could easily fall out of the baskets.
For rinsing in the dishwasher the following c
For rinsing in the dishwasher the following cutlery and
For rinsing in the dishwasher the following cFor rinsing in the dishwasher the following c
..
..are not suitable
are not suitable::::
....
are not suitableare not suitable
- Cutlery with hand pieces of wood, porcelain
mother of pearl
- Plastic items that are not heat resistant
- Older cutlery with glued parts that are not tem-
perature resistant
- Bonded cutlery items or dishes
utlery and dishes..
utlery and utlery and
dishes..
dishes..dishes..
..
..are limited suitable
are limited suitable::::
....
are limited suitableare limited suitable
- some types of glasses can become dull after a
large number of washes
- silver and aluminum parts have a tendency to
discolor during washing
- Glazed patterns may fade if machine washed
frequently
- Pewter or cooper items
- Crystal glass
- Steel items subject to rusting
- Wooden platters
- Items made from synthetic fibres
12
Recommendations for loading
Recommendations for loading
Recommendations for loadingRecommendations for loading
• Arrange sensitive, light tableware items such as glasses, coffee and tea cups in the upper basket.
• Place large items that are most difficult to clean in the lower basket.
• Make sure that the tableware is placed securely and cannot tip over.
• Place all items so, that the spray arms can rotate freely during rinsing.
• Arrange all items with openings facing down.
• Curved items, or ones with recesses, should be loaded aslant so that water can drain off.
• Make sure that glasses do not touch each other.
• Set the dishes and cutlery not into each other or covering each other.
• Arrange cutlery in the cutlery rack.
• Store long as well as sharp cutlery in the cutlery rack or horizontally in the dishwasher basket.
MMMMethod
ethods for
s for loading n
ethodethod
Loading the upper basket
Loading the upper basket
Loading the upper basketLoading the upper basket
loading normal
s fors for
loading nloading n
ormal ddddishw
ormal ormal
ishware
are
ishwishw
areare
On the upper basket only
Loading the lower basket
Loading the lower basket
Loading the lower basketLoading the lower basket
The basket is suitable because
small and medium items
should be loaded. Load e.g.
glasses, cups, saucers and
late holderslate holders
If necessary, fold the
cup shelves downwards
or remove them.
Lift the racks slightly and fold them down.
Adjusting the upper basket
Adjusting the upper basket
Adjusting the upper basketAdjusting the upper basket
of the particularly intense cleaning action of the lower spray
arm for heavily soiled dishes.
Load e.g. pots and plates.
In order to create a better arrangement for bulky dishes, the racks
can be folded.
The height of the upper basket can be adjusted by placing the wheels on rails of different heights. This will
create more space for large items in the upper as well as in the lower basket.
• Pull out the basket guides.
• Remove the basket out of the guides.
• Depending on the desired setting, insert the upper or lower pair of wheels into
the guide; the left and right side should always be located at the same height.
13
Cutlery
Cutlery rack
Cutlery Cutlery
rack
rackrack
The cutlery is sorted into the separate cutlery rack in its appropriate positions.
You may sort the cutlery evenly distributed, vertically with the narrow side, so that the
water can drains off. Extra long, large parts must be arranged in the middle of the
rack.
Depending on the loading requirements of the upper dishwasher basket as well as the cutlery rack, cutlery
rack can be adjusted into different positions.
Position 1
Position 1
Position 1Position 1
both sides are
inclined
Position 2
Position 2
Position 2Position 2
left horizontal; right
inclined
Position 3
Position 3
Position 3Position 3
both sides are
horizontal
Position 4
Position 4
Position 4Position 4
sides are overlapped
Position 5
Position 5
Position 5Position 5
only the left side is
used
Lift the left side up. Adjust the left side
to lower position.
Lift the right side
up.
Move the right side to
the left.
Remove the right side.
Starting a Rinse Program
Starting a Rinse Program
Starting a Rinse ProgramStarting a Rinse Program
Rinse cycle table
Rinse cycle table
Rinse cycle tableRinse cycle table
Select a suitable program depending on dishes and degree of soiling.
Detergent
Detergent
Detergent Detergent
pre/main
pre/main
pre/mainpre/main
(g)
(g)
(g)(g)
Pr
Proooogram
gram
PrPr
gramgram
Program
Program selection
ProgramProgram
selection
selectionselection
information
information
informationinformation
Pro
Program
gram sequence
gramgram
sequence
sequencesequence
ProPro
Pre-rinse (45°C)
Auto wash
normally to heavily
soiled dishes, dried
leftovers
Auto-rinse (45-55°C)
Rinse 1
Rinse 2 (65°C)
5/30
(or Tab)
Drying
The appliance detects the degree of soiling of the loading. The rinsing parameters are automatically adjusted.
Pre-rinse (50°C)
Main rinse (60°C)
Intensive
heavily soiled dishes
and dried leftovers
Rinse 1
Rinse 2
5/30
(or Tab)
Rinse 3 (70°C)
Drying
Running
Running
Running Running
time
time
time time
(Min.)
(Min.)
(Min.)(Min.)
150
175 1.6 17.5
Energy
Energy
EnergyEnergy
(kWh)
(kWh)
(kWh)(kWh)
0.9 –
1.3
Water
Water
WaterWater
(L)
(L)
(L)(L)
11 – 15
Rinse
Rinse
Rinse Rinse
aid
aid
aidaid
14
Program
Pr
Proooogram
gram
PrPr
gramgram
Normal
ECO
(*EN 50242)
Program selection
ProgramProgram
normally soiled dishes,
daily use
standard program for
normally soiled dishes
selection
selectionselection
information
information
informationinformation
90 Min for lightly soiled dishes
low adhesive, fresh
Glass
leftovers, such as
glasses
rapid rinse cycle for
Rapid
lightly soiled dishes
without drying
Soak
NOTE
NOTE::::
NOTENOTE
dishes that shall be
rinsed later that day
Detergent
Program
Program sequence
ProgramProgram
sequence
sequencesequence
Detergent
Detergent Detergent
pre/main
pre/main
pre/mainpre/main
(g)
(g)
(g)(g)
Running
Running
Running Running
time
time
time time
(Min.)
(Min.)
(Min.)(Min.)
Energy
Energy
EnergyEnergy
(kWh)
(kWh)
(kWh)(kWh)
Water
Water
WaterWater
(L)
(L)
(L)(L)
Rinse
Rinse
Rinse Rinse
aid
aid
aidaid
Pre-rinse (45°C)
Main rinse (55°C)
Rinse 1
Rinse 2 (65°C)
5/30
(or Tab)
185 1.3 13.5
Drying
Pre-rinse
Main rinse (45°C)
Rinse (55°C)
5/30
(or Tab)
220 0.83 10
Drying
Main rinse (65°C)
Rinse 1
Rinse 2 (65°C)
35
(or Tab)
90 1.35 12.5
Drying
Pre-rinse
Main rinse (40°C)
Rinse 1
Rinse 2 (60°C)
5/30
(or Tab)
130 0.9 13
Drying
Main rinse (45°C)
Rinse 1 (50°C)
25 30 0.75 11
Rinse 2 (55°C)
Pre-rinse - 15 0.02 4
• The extra addition of rinse aid can improve the drying result.
• *EN 50242: this program is the test program and of combined energy and water consumption most effi-
cient. The information for comparability:
Capacity: 14 settings; Position of the upper basket: upper wheels on rails; Rinse aid setting: 6
Alternative wash
Alternative wash (choosing the washing zone)
Alternative washAlternative wash
(choosing the washing zone)
(choosing the washing zone)(choosing the washing zone)
This additional function can be activated depending on the basket loading, only upper or lower basket.
Water, energy and time can be saved. Do add a little less detergent than for a full load.
Option
Option
OptionOption
NOTE
NOTE::::
NOTENOTE
The options are not available for the rinse programs RAPID and SOAK.
Extra drying
Extra drying
Extra dryingExtra drying
: The rinse temperature during the rinsing is increased and the drying phase is extended. For
optimum drying of e.g. plastic ware.
15
Power wash
Power wash
Power washPower wash
: The rinse temperature and duration is increased. For a better rinsing performance; ideal for e.g.
cleaning cutting boards or baby bottles.
Express
Express
ExpressExpress
Delay time
Delay time
Delay timeDelay time
: The duration of the corresponding rinse program is reduced. For lightly soiled dishes.
The program start can be delayed by 00:30 – 24:00 hours. The operation will start automatically with the previously set operating conditions after the selected lead time has elapsed.
About the MENÜ (menu) button [CANCEL DELAY] the delay time can be cancelled.
Control panel
Control panel
Control panelControl panel
1111 Holding pressed the power button to switch on/off the power supply. The control lamp indicates the status.
2222 By repeatedly pressing the MENÜ (menu) button you select the menu items. See display indications.
3333 OK button to confirm your operating settings.
4444 Arrow backwards <<<< to scroll to the next settings.
5555 Arrow forwards >>>> to scroll to the previous settings.
6666 Via the display the following menu items can be selected and the required operating settings made:
- Language - Adj. Salt Cons. - Programs
- Delay time - Alternative Wash - Option
Via the display the following will be indicated:
- start delay time (if activated)
- the program section with rinse temperature
- the expected remaining time
- possibly occurring error codes / messages
- the information when the corresponding container of rinse aid or salt must be refilled
Starting a
Starting a rinse
Starting a Starting a
rinse program
program
rinserinse
programprogram
• The water supply must be opened up to the maximum pressure.
• Load the dishwasher baskets.
• Fill in the detergent.
• Press the power button to switch on the appliance.
• Select the desired rinse cycle.
• Set the available options, if required.
• Close the appliance door and the dishwasher starts.
16
Program c
Program change
Program cProgram c
CAUTION:
CAUTION:
CAUTION:CAUTION:
hange
hangehange
A program change should be done only a short time after starting the program. Otherwise, maybe detergent
has been released and already drained rinse water.
• To do a program change, open the appliance door carefully so that you can operate the control panel.
• Cancel the program via the MENÜ (menu) button [CANCEL PROGRAMS].
• Select the new program and close the appliance door to start the new operation.
Forgot to add a dish?
Forgot to add a dish?
Forgot to add a dish?Forgot to add a dish?
WARNING:
WARNING:
WARNING:WARNING:
Open the door very carefully during operation, there is a risk of water squirting out.
Dishware can be added any time before the detergent dispenser opens.
• Open the appliance door a little
• Once the spray arms stopped working, you can open the door completely.
• Add forgotten dishware.
• Close the appliance door, after approx. 10 seconds the operation will be continued.
At the e
At the end of program
At the eAt the e
nd of program
nd of programnd of program
CAUTION:
CAUTION:
CAUTION:CAUTION:
Allow the appliance to cool down a bit after the program has ended, before you open it. This avoids that steam
escapes that causing long-term damages to your furniture.
At the end of the rinse cycle will sound a series of signals; then the unit goes into standby mode.
Switch off
Switch off
Switch offSwitch off
• Open the appliance door and switch the appliance off by pressing the power button.
• Close the water supply!
• Remove the dishes after cooling (see "Unloading the dishwasher baskets").
• If the appliance is not in use for an extended period:
-
Disconnect the mains plug or switch off or turn out the fuse and
-
leave the appliance door slightly open until the next rinse cycle to avoid odors.
Unloading
Unloading the dishwasher baskets
UnloadingUnloading
CAUTION
CAUTION::::
CAUTIONCAUTION
Let the dishware cool down for about 15 minutes before unloading. Hot dishes are sensitive to knocks.
NOTE
NOTE::::
NOTENOTE
the dishwasher baskets
the dishwasher basketsthe dishwasher baskets
At the end of program there could be still water drops inside the appliance.
• Open the door and pull out the basket.
• To avoid water dripping from the upper basket onto the dishes in the lower basket, it is advisable to unload
the appliance from the bottom up.
17
Cleaning
WARNING:
WARNING:
WARNING:WARNING:
Cleaning and Maintenance
CleaningCleaning
and Maintenance
and Maintenanceand Maintenance
• Always switch off the appliance and disconnect the plug or turn off / unscrew the fuse before cleaning and
user maintenance.
• Allow the appliance to cool down sufficient before cleaning.
• Do not use steam cleaners for cleaning the appliance; moisture could enter electrical components. Risk of
electric shock!
electric shock! Hot steam could damage the plastic parts. The appliance must be dry before restarting op-
electric shock!electric shock!
eration.
CAUTION
CAUTION::::
CAUTIONCAUTION
Risk of
Risk of Risk of
• Do not use a wire brush or other sharp, abrasive items.
• Do not use any acidic or abrasive detergents.
NOTE
NOTE::::
NOTENOTE
Dirty filters and clogged spray arms degrade the rinsing. Regularly check the filter and spray arms and clean
them if necessary.
Filter
Filter system
system
FilterFilter
systemsystem
The three-part filter system prevents larger amounts of food or other objects from getting inside the pump.
1: Main filter: food and soil particles trapped in this filter are pulverized by a special jet on the
lower spray arm and washed down to drain.
2: Coarse filter: filters out larger items such as pieces of bone or glass shards that could
block the drainage.
3: Micro filter: filters dirt and food residues in the sump area and prevents it from being redeposited on the dishware during rinse cycle.
Cleaning the filter system
Cleaning the filter system
Cleaning the filter systemCleaning the filter system
CAUTION:
CAUTION:
CAUTION:CAUTION:
• The dishwasher must never be used without the filter.
• Improper replacement of the filter can reduce performance and damage the appliance.
• Do not knock out the filter for cleaning to avoid possible deformations of the filters.
NOTE
NOTE::::
NOTENOTE
Check after each rinsing the filter for residues.
• Turn the coarse filter counterclockwise and remove the whole filter system upwards.
• Remove the coarse as well as the micro filter from the main filter.
• Remove leftover food and clean the filters under running water. Use a soft brush, if neces-
sary.
• Put the filter system properly in reverse order together and reinstall in its provided posi-
tion. Fix the entire system, by tightening the filter unit clockwise.
18
Cleaning the spray arms
Cleaning the spray arms
Cleaning the spray armsCleaning the spray arms
Lime and impurities from the rinsing water can block nozzles and bearings of the spray arms. Check the outlet
nozzles of the spray arms regularly for blockages.
• Unscrew the securing nut of the upper spray and pull off the arm downwards.
• Pull off the lower spray arm upwards.
• Clean the arms under running water; if necessary use a soft brush for the nozzles.
• Insert the spray arms again until they clicks into place and tighten the nut of the upper
spray arm.
Maintenance of the dishwasher
Maintenance of the dishwasher
Maintenance of the dishwasherMaintenance of the dishwasher
CAUTION
CAUTION::::
CAUTIONCAUTION
Never use spray cleaners to clean the door panel, this may damage the door lock and electrical components.
• Clean the appliance outer surfaces and the door sealing thoroughly with a soft, damp cloth. Use only mild
cleaning agent.
• Use to remove stains inside the appliance a dampened cloth with a little white vinegar or a special deter-
gent for dishwashers. If necessary, fill detergent in and start the appliance without dishware in the program
with the highest rinse temperature.
• Dry the outer surfaces thoroughly before taking in operation again.
AAAAntifreeze
ntifreeze protection
ntifreezentifreeze
If the unit is out of operation and exposed to temperatures below zero, observe the following precautions:
protection
protectionprotection
• Disconnect the mains plug.
• Close the water supply and remove the inlet hose from the water valve.
• Drain the water from the inlet hose and the water valve.
• Reconnect the inlet hose to the water valve.
• Turn off the lid of the salt container and take off the filter system. Remove the remaining water in the sump
with an absorbent sponge.
Energy saving
Energy saving ttttips
Energy saving Energy saving
ips
ipsips
• Always try to operate the dishwasher when it is fully loaded.
• Do not rinse the dishes in advance under running water.
• Use for each type of load the most appropriate rinse program.
• Do not perform a pre-rinse (depending on model), if not absolutely necessary.
• If available, the appliance should be connected to a hot water supply up to 60°C.
19
Before you contact an authorized specialist
Water is not drained off
Before you contact an authorized specialist
Before you contact an authorized specialistBefore you contact an authorized specialist
Problem
Problem Possi
ProblemProblem
The appliance is not
working
Possible causes
ble causes What do to
PossiPossi
ble causesble causes
Fuse blown or the circuit
breaker acted
Troubleshooting
Troubleshooting
TroubleshootingTroubleshooting
What do to
What do toWhat do to
Replace fuse or reset circuit breaker. Remove any other
units sharing the same circuit with the dishwasher.
Power supply is not turned
on
Insert the power plug properly. Make sure the appliance is
switched on and the door is closed securely.
Water pressure is low Check if the water supply is connected properly and the wa-
ter is turned on.
Kink in drain hose Check the drain hose.
Filter clogged Check the filter system.
Kitchen sink clogged Check kitchen sink to make sure it is draining well. If the
kitchen sink is clogged, you may need a specialist.
Noise Some audible sounds are
E.g. sound form detergent dispenser opening.
normal
Dishware is not secured Take care that the dishware is secured in the dishwasher.
The spray arm knocks
against a piece of tableware
Place the parts so that the spray arm can rotate freely dur-
ing rinsing.
Suds in the tub Improper detergent Use only special dishwasher detergent to avoid suds. If this
occurs, open the door and let suds evaporate. Add approx
4 liter cold water to the tub. Close the door and start a short
rinse cycle to drain out the water.
Spilled rinse agent Always wipe up rinse agent spills immediately.
Stained tub interior Detergent with colorant was
used
Dishes and flatware
not clean
Spots and filming on
glasses and flatware
Improper program Select a stronger program.
Improper basket loading Make sure that the action of the detergent dispenser and
Extremely hard water
Low inlet temperature
Overloading the baskets
Improper loading
Old or damp detergent
Empty rinse dispenser
Incorrect dosage of detergent
Cloudiness on
glassware
Combination of soft water
and too much detergent
Only use detergent without colorant.
spray arm are not blocked by large dishes.
To remove spots of glassware:
- Take out all metal utensils of the appliance.
- Do not add detergent.
- Select a longer rinse cycle.
- Start the dishwasher and allow it to run for about
15 minutes up to the main rinse.
- Pour 2 cups of white vinegar into the appliance bottom.
- Let complete the rinse cycle. If the vinegar does not work:
repeat as above, except use ¼ cup (60 ml) of citric acid
crystals instead of vinegar.
Use less detergent if you have soft water and select a short-
est cycle to rinse glassware and to get clean.
20
Problem
Yellow or brown film on
Black or grey marks on
Problem Possible causes
ProblemProblem
Possible causes What do to
Possible causesPossible causes
Tea or coffee stains Using a solution of ½ cup of bleach and 3 cups of warm wa-
inside surface
What do to
What do toWhat do to
ter to remove the stains by hand.
Iron deposits in water can
Call a water softener company for a special filter.
cause an overall film
White film on inside
surface
Detergent dispenser
close not properly
Detergent left in dis-
Hard water minerals To clean the interior, use a damp sponge with dishwasher
detergent. Wear rubber gloves.
Clogged detergent residue
Clean the detergent from the catch.
is blocking the catch
Dishes blocks the dispenser Reload the dishes.
penser
Steam Normal There is some steam coming through the vent by the door
latch during drying and water draining.
Aluminum utensils have
dishware
Water standing on the
rubbed against dishware
Normal A small amount of clean water around the outlet on the tub
bottom of the tub
Dishwasher leaks Overfill dispenser or rinse
aid spills
Error
Error codes
codes
Error Error
codescodes
Use a mild abrasive cleaner to eliminate those marks.
bottom keeps the water seal lubricated.
Do not overfill the dispenser. Spilled rinse aid could cause
oversudsing and lead to overflowing.
With some malfunctions the appliance displays the following error codes to warn you:
Display indication
Display indication Possible causes
Display indicationDisplay indication
Error 1
Error 1 Water inlet malfunction.
Error 1Error 1
Error 3
Error 3 Not reaching required temperature. Malfunction of heating element.
Error 3Error 3
Error 4
Error 4 Possible overflow / leakage occurs.
Error 4Error 4
Error 8
Error 8 Water diversion system malfunction.
Error 8Error 8
Error 9
Error 9 Button is pressed more than 30 seconds. If not by a person, there is possibly water on the
Error 9Error 9
Possible causes
Possible causesPossible causes
circuit board.
CAUTION
CAUTION::::
CAUTIONCAUTION
• If overflow occurs, turn off the main water supply before calling an authorized technician.
• If there is water in the lower housing part due to an overfilling or a small leak, remove this water before
restarting the appliance.
NOTE:
NOTE:
NOTE:NOTE:
If a problem still persists after following the steps above, please contact your distributor or an authorized technician.
21
Technical Data
Technical Data
Technical DataTechnical Data
Measu
Measure
re / Weight
MeasuMeasu
/ Weight
rere
/ Weight/ Weight
Height x Width x Depth cm 81.5 x 59.8 x 55.0
Net weight kg 39.5
Electrical connection / water connection
Electrical connection / water connection
Electrical connection / water connectionElectrical connection / water connection
Connection power W 1930
Connection voltage V~ / Hz 220-240 / 50
Fuse protection A 10
Water protection Mpa (bar) 0.04 – 1.0 (0.4-10)
The right to make technical and design modifications in the course of continuous product development remains reserved.
Product data sheet for household
Product data sheet for household dishwasher
Product data sheet for household Product data sheet for household
Brand
Brand
BrandBrand
Model
Model
ModelModel
Standard place settings
Standard place settings
Standard place settingsStandard place settings
Energy efficiency class1)
dishwasher aaaaccor
dishwasherdishwasher
ccording to re
ccorccor
ding to regulation (EU) No. 1059
ding to reding to re
gulation (EU) No. 1059/2010
gulation (EU) No. 1059gulation (EU) No. 1059
BOMANN
BOMANN
BOMANNBOMANN
GSP
GSPEEEE 888872
GSPGSP
11114444
A+++
/2010
/2010/2010
72
7272
Annual energy consumption2) kWh 237
Energy consumption of the standard cleaning cycle kWh 0.83
Power consumption of the off mode W 0.45
Power consumption of the left-on mode W 0.49
Weighted annual water consumption3) l 2800
Drying efficiency class4)
A
Standard program to which the information relates to the
ECO 45°C
label and the data sheet5)
Program duration of the standard cleaning cycle Min. 195
Duration of the left-on mode Min. 30
Noise emission dB(A) re1pW
Built-in appliance
1) A+++ (highest efficiency) to D (lowest efficiency).
2) Based on 280 standard cleaning cycles using cold water fill and the consumption of the low power models. Actual energy consumption will depend on
how the appliance is used.
3) Based on 280 standard cleaning cycles. Actual water consumption will depend on how the appliance is used.
4) A (highest efficiency) to G (lowest efficiency).
5) This program is suitable for cleaning normally soiled tableware and that it is the most efficient program in terms of its combined energy and water con-
sumption for that type of tableware.
Note: The above values have been measured in accordance with standards under specified operating conditions. Results may vary greatly according to
quantity and pollution of the dishes, water hardness, amount of detergent, etc.
44
•
This appliance has been tested according to all relevant current CE guidelines, such as electromagnetic compatibility and low voltage directives, and has been constructed in accordance with the latest safety regulations
22
Disposal
Disposal
DisposalDisposal
Meaning of the “Dustbin” Symbol
Meaning of the “Dustbin” Symbol
Meaning of the “Dustbin” SymbolMeaning of the “Dustbin” Symbol
Protect our environment; do not dispose of electrical equipment in the domestic waste.
Please return any electrical equipment that you will no longer use to the collection points provided for their
disposal.
This helps avoid the potential effects of incorrect disposal on the environment and human health.
This will contribute to the recycling and other forms of reutilization of electrical and electronic equipment.
Information concerning where the equipment can be disposed of can be obtained from your local authority.
WARNING:
WARNING:
WARNING:WARNING:
Remove or disable any existing snap and bolt locks, if you take the appliance out of operation or dispose it.
23
C. Bomann GmbH
C. Bomann GmbH
C. Bomann GmbHC. Bomann GmbH
www.bomann.de
www.bomann.de
www.bomann.dewww.bomann.de
Stand 12/16
Made in P.R.C.
24
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.