Black & Decker HD4810, HD5010, HD5010A5, HD5010KHA7, HD5010VA5 User Manual

HD4810/HD5010

HD5010A5/HD5010KHA7/

HD5010VA5/ HD5513KA40/

HD5513KHA/HD5513V

www.blackanddecker.ae

ENGLISH

2

E

BA

D

F

C

7

9

10

8

11

3

6 7

4

5

6

7

3

1

2

The illustratrions are for representative purposes only, they can differ from actual product.

Intended use

Your Black & Decker drill has been designed for drilling in

wood, metal and plastics and masonry. This tool is intended

for consumer use only.

Safety instructions

General power tool safety warnings.

Warning! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions listed below may result in electric

shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in all of the warnings listed below

refers to your mains operated (corded) power tool or battery

operated (cordless) power tool.

1. Work Area Safety

a. Keep work area clean and well lit. Cluttered and dark

areas invite accidents.

b. Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Power tools create sparks which may ignite the

dust or fumes.

c. Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2. Electrical Safety

a. Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b. Avoid body contact with earthed or grounded surfaces

such as pipes, radiators, ranges and refrigerators. There

is an increased risk of electric shock if your body is

earthed or grounded.

c. Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d. Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

e. When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electric shock.

3. Personal Safety

a. Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a power

tool while you are tired or under the influence of drugs,

alcohol or medication. A moment of inattention while

operating power tools may result in serious personal

injury.

b. Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal

injuries.

c. Prevent unintentional starting. Ensure the switch is in the

off-position before connecting to power source and/or

battery pack, picking up or carrying the tool. Carrying

power tools with your finger on the switch or energising

power tools that have the switch on invites accidents.

d. Remove any adjusting key or wrench before turning the

power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal

injury.

e. Do not overreach. Keep proper footing and balance at all

times. This enables better control of the power tool in

unexpected situations.

f. Dress properly. Do not wear loose clothing or jewellery.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewellery or long hair can be caught

in moving parts.

g. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of these devices can

reduce dust related hazards.

4. Power Tool Use and Care

a. Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the job

better and safer at the rate for which it was designed.

b. Do not use the power tool if the switch does not turn it on

and off. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

3

ENGLISH

4

ENGLISH

c. Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk

of starting the power tool accidentally.

d. Store idle power tools out of the reach of children and do

not allow persons unfamiliar with the power tool or these

instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

e. Maintain power tools. Check for misalignment or binding

of moving parts, breakage of parts and any other

condition that may affect the power tools operation. If

damaged, have the power tool repaired before use.

Many accidents are caused by poorly maintained power

tools.

f. Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

5. Service

a. Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Additional power tool safety warnings

• Wear ear protectors with impact drills. Exposure to noise

can cause hearing loss.

• Use auxiliary handles supplied with the tool. Loss of

control can cause personal injury.

• Hold power tool by insulated gripping surfaces when

performing an operation where the cutting tool may

contact hidden wiring or its own cord. Contact with a

“live” wire will also make exposed metal parts of the

power tool “live” and shock the operator.

• Use clamps or another practical way to secure and

support the workpiece to a stable platform. Holding the

work by hand or against your body leaves it unstable and

may lead to loss of control.

• Before drilling into walls, floors or ceilings check for the

location of wiring and pipes.

• Avoid touching the tip of a drill bit just after drilling, as it

may be hot

Safety of others

• This tool is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

• Children should be supervised to ensure that they do not

play with the appliance.

6. Labels on tool

The label on your tool may include the following symbols:

Electrical safety

This tool is double insulated; therefore no earth wire is

required. Always check that the power supply

corresponds to the voltage on the rating plate.

• If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features (Fig. A)

1. Variable speed switch

(Only for HD5010VA5, HD5513V,

HD5513KA40,HD5513KHA)

2. Lock-on button

3. Forward/ reverse slider, Depth stop & Side handle

(Only for HD5513V, HD5513KHA, KHA40V)

Hz ....... Hertz

W ....... Watts

min ..... minutes

..... Alternating

Current

..... Direct

Current

Read

Instructions

Manual

Use Eye

Protection

Use Ear

Protection

...... Class II

Construction

...... Earthing

Terminal

...... Safety

Alert Symbol

.../min.. Revolutions

or Recipro-

cation per

minute

V ........ Volts

A ........ Amperes n

0

....... No-Load

Speed

5

ENGLISH

4. Drilling mode selector

5. Chuck

Assembly

Warning! Before assembly, make sure that the

tool is switched off and unplugged.

Fitting the side handle and depth stop (fig. B)

(Only for HD5513V,HD5513KA40,HD5513KHA)

• Turn the grip counterclockwise until you can slide the

side handle (7) onto the front of the tool as shown.

• Rotate the side handle into the desired position.

• Insert the depth stop (6) into the mounting hole as

shown.

• Set the drilling depth as described below.

• Tighten the side handle by turning the grip clockwise.

Fitting a drill bit or screwdriver bit

Keyed chuck (fig. C)

• Open the chuck by turning the sleeve (9)

counterclockwise.

• Insert the bit shaft (8) into the chuck.

• Insert the chuck key (10) into each hole (11) in the side

of the chuck and turn clockwise until tight.

Removing and refitting the chuck (fig. D)

• Open the chuck as far as possible.

• Remove the chuck retaining screw, located in the chuck,

by turning it clockwise using a screwdriver.

• Tighten an Allen key into the chuck and strike it with a

hammer as shown.

• Remove the Allen key.

• Remove the chuck by turning it counterclockwise.

• To refit the chuck, screw it onto the spindle and secure it

with the chuck retaining screw

Use

Warning! Let the tool work at its own pace. Do not

overload.

Warning! Before drilling into walls, floors or ceilings,

check for the location of wiring and pipes.

Selecting the direction of rotation (fig. E)

For drilling and for tightening screws, use forward (clockwise)

rotation. For loosening screws or removing a jammed drill bit,

use reverse (counterclockwise) rotation.

• To select forward rotation, push the forward/reverse slider

(3) to the centre position.

• To select reverse rotation, push the forward/reverse slider

to the left.

Warning! Never change the direction of rotation while the

motor is running.

Selecting the drilling mode

• For drilling in masonry, set the drilling mode selector (3)

to the position.

• For drilling in other materials and for screwdriving, set the

drilling mode selector to the position.

Setting the drilling depth (fig. F)

(Only for HD5513V, HD5513KA40, HD5513KHA)

• Slacken the side handle (7) by turning the grip

counterclockwise.

• Set the depth stop (6) to the desired position. The

maximum drilling depth is equal to the distance between

the tip of the drill bit and the front end of the depth stop.

• Tighten the side handle by turning the grip clockwise.

Switching on and off

• To switch the tool on, press the speed switch (1). For

tools with variable speed switch, the tool speed depends

on how far you press the switch. As a general rule, use

low speeds for large diameter drill bits and high speeds

for smaller diameter drill bits. ( HD5010VA5, HD5513V,

HD5513KA40,HD5513KHA )

6

ENGLISH

• For continuous operation, press the lock-on button (2)

and release the speed switch. This option is available

only at full speed. This option does not work in reverse

rotation.

• To switch the tool off, release the speed switch. To

switch the tool off when in continuous operation, press

the speed switch once more and release it.

Accessories

The performance of your tool depends on the accessory

used. Black & Decker accessories are engineered to high

quality standards and designed to enhance the performance

of your tool. By using these accessories you will get the very

best from your tool.

Maintenance

Your tool has been designed to operate over a long period of

time with a minimum of maintenance. Continuous

satisfactory operation depends upon proper tool care and

regular cleaning.

Warning! Before performing any maintenance,

switch off and unplug the tool.

• Regularly clean the ventilation slots in your tool using a

soft brush or dry cloth.

• Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

Mains plug replacement

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in the new

plug.

• Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the fitting instructions supplied with good quality

plugs. Recommended fuse: 5 A.

Technical data

Voltage V

DC

AR, B2C

220–240V ~ 50/60Hz 220–240V ~ 50/60Hz

Power input W 480 500

No load speed min

-1

3000 3000

Max drill capacity

Steel/Concrete mm 10 10

Wood mm 20 20

HD4810 HD5010 / HD5010A5

Voltage VDC

AR, B2C

220–240V ~ 50/60Hz 220–240V ~ 50/60Hz

Power input W 500 500

No load speed min-1 2800 0-2800

Max drill capacity

Steel/Concrete mm 10 10

Wood mm 20 20

HD5010KHA7 HD5010VA5

Voltage V

DC

AR, B2C 220–240V ~ 50/60Hz

Power input W 550

No load speed min

-1

0-2800

Max drill capacity

Steel/Concrete mm 10

Wood mm 20

HD5513V / HD5513KHA

HD5513KA40

7

ENGLISH

Protecting the environment

Separate collection. This product must not be

disposed of with normal household waste.

Should you find one day that your Black & Decker

product needs replacement, or if it is of no further use to you,

do not dispose of it with household waste. Make this product

available for separate collection.

Separate collection of used products and

packaging allows materials to be recycled and used

again. Reuse of recycled materials helps prevent

environmental pollution and reduces the demand for raw

materials.

Local regulations may provide for separate collection of

electrical products from the household, at municipal waste

sites or by the retailer when you purchase a new product.

Black & Decker provides a facility for the collection and

recycling of Black & Decker products once they have

reached the end of their working life. To take advantage of

this service please return your product to any authorised

repair agent who will collect them on our behalf.

You can check the location of your nearest authorised repair

agent by contacting your local Black & Decker office at the

address indicated in this manual. Alternatively, a list of

authorised Black & Decker repair agents and full details of

our after-sales service and contacts are available on the

Internet at: www.2helpU.com.

Guarantee

Black & Decker is confident of the quality of its products and

offers an outstanding guarantee. This guarantee statement is

in addition to and in no way prejudices your statutory rights.

The guarantee is valid within the territories of the Member

States of the European Union and the European Free Trade

Area.

If a Black & Decker product becomes defective due to faulty

materials, workmanship or lack of conformity, within 24

months from the date of purchase, Black & Decker

guarantees to replace defective parts, repair products

subjected to fair wear and tear or replace such products to

make sure of the minimum inconvenience to the customer

unless:

• The product has been used for trade, professional or hire

purposes.

• The product has been subjected to misuse or neglect.

• The product has sustained damage through foreign

objects, substances or accidents.

• Repairs have been attempted by persons other than

authorised repair agents or Black & Decker service staff.

To claim on the guarantee, you will need to submit proof of

purchase to the seller or an authorised repair agent. You can

check the location of your nearest authorised repair agent by

contacting your local Black & Decker office at the address

indicated in this manual. Alternatively, a list of authorised

Black & Decker repair agents and full details of our aftersales

service and contacts are available on the Internet at:

www.2helpU.com

Please visit our website www.blackanddecker.co.uk to

register your new Black & Decker product and to be kept up

to date on new products and special offers. Further

information on the Black & Decker brand and our range of

products is available at www.blackanddecker.co.uk.

8

FRANÇAIS

E

BA

D

F

C

7

9

10

8

11

3

6 7

4

5

6

7

3

1

2

Les illustrations sont seulement données à titre indicatif et peuvent différer du produit réel.