Please Read and Save this Use and Care Book.
IMPORTANT SAFEGUARDS.
When using your iron, basic safety precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING.
•Only use iron for its intended use.
•To avoid risk of electric shock, do not immerse the iron in water or other liquids.
•Always turn iron off before plugging or unplugging from the electrical outlet. Never pull on the cord to disconnect the iron from the electrical outlet; instead, grasp the plug and pull on the plug to disconnect the iron.
•Do not let the cord touch hot surfaces. Let the iron cool completely before putting the iron away. Coil the cord loosely around the iron when storing.
•Always disconnect the iron from the electrical outlet before filling the iron with water, emptying the water from the iron, and when the iron is not in use.
•Do not operate the iron with a damaged cord or in the event the iron has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the iron. Take it to a qualified serviceman for examination and repair. Incorrect assembly might result in a risk of electric shock when the iron is used after reassembly.
•Close supervision is necessary for any appliance used by or near children. Do not leave the iron unattended while the iron is connected or on an ironing board.
•Burns can occur from touching hot metal parts, hot water or steam. Use caution when you turn a steam iron upside down— there might be hot water in the reservoir.
•This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
•Children should be supervised to ensure that they do not play with the appliance.
•The iron must be used and rested on a stable surface.
•When placing the iron on its stand, ensure that the surface on which the stand is placed is stable.
•The iron is not to be used if it has been dropped, if there are visible signs of damage or if it is leaking.
SPECIAL INSTRUCTIONS.
•To avoid a circuit overload, do not operate an iron on the same circuit with another high wattage appliance.
•If an extension cord is absolutely necessary, a cord with an ampere rating equal to or greater than the maximum rating of the iron should be used. A cord rated for less amperage can result in a risk of fire or electric shock due to overheating. Care shall be taken to arrange the cord so that it cannot be pulled or be tripped over.
SAVE THESE INSTRUCTIONS.
This product is for household use only.
POLARIZED PLUG (120V MODELS ONLY)
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way.
TAMPER-RESISTANT SCREW
Warning: This appliance is equipped with a tamper-resistant screw to prevent removal of the outer cover. To reduce the risk of fire or electric shock, do not attempt to remove the outer cover. There are no user-serviceable parts inside. Repair should be done only by authorized service personnel.
Note: If the power supply cord is damaged, it should be replaced by qualified personnel; in Latin America, by an authorized service center.
HOW TO USE
This product is for household use only.
GETTING STARTED
•Remove any labels, stickers or tags attached to the body or soleplate of the iron.
•Please go to www.prodprotect.com/applica to register your warranty. Note: Use ordinary tap water for ironing. Do not use water processed through a home softening system.
Important: For optimum performance, let the iron stand for 90 seconds before beginning to iron.
FILLING WATER TANK |
|
1. With iron on flat surface with soleplate down, open |
A |
water-fill cover (A). |
2.Tilt the iron and using a clean measuring cup, pour
water into opened chamber until water reaches the MAX level mark on the side of the water tank. Do not overfill.
3.Close the water-fill cover.
4.Plug in the iron. The power indicator light illuminates.
Note: If you need to add water while ironing, unplug the iron and follow above steps.
Tip: If unsure of a garment’s fiber, test a small area (on an inside seam or hem) before ironing.
3-WAY AUTOMATIC SHUTOFF
The automatic shutoff feature in your iron works as follows:
• Once the iron reaches appropriate temperature, |
|
|
it will turn off after 30 seconds of inactivity if left |
|
|
on its soleplate or tipped over on its side. If left |
30 seconds |
|
vertically on its heel rest, it will shut off after |
||
|
||
8 minutes (B). |
8 minutes |
|
• The power indicator light starts blinking to let you |
||
B |
||
know that the iron has stopped heating. |
||
|
•As soon as you pick up the iron, it will start heating
again. Wait for iron to reheat completely before resuming operation.
SMART STEAMTM TECHNOLOGY
The Smart SteamTM system automatically produces steam when you turn the fabric select dial between settings 4 and 6.
SURGE OF STEAM
Horizontal
Tip: Use to remove stubborn creases.
1.With the water tank filled to the MAX mark, set fabric select dial to appropriate setting (between 4 and 6) for your fabric. See fabric guide on water tank and read garment’s label to help you determine fabric type.
2.Be sure there is water in the reservoir. Steam is automatically turned off between settings 0 and 3.
3.For best performance, use surge of steam at 5-second intervals.
4.When finished ironing, turn the fabric select dial to 0 and unplug the iron.
Important: Always stand the iron on its heel rest when powered on but not in use.
Vertical
Tip: Use for removing wrinkles from hanging clothes and drapes.
1.Be sure the water tank is filled to the MAX mark.
2.Hang the garment to be steamed on a clothes hanger. (Curtains or drapes can be steamed once they are hung.)
3.Set the fabric select dial to appropriate setting (between 4 and 6) for your fabric.
4.Hold the iron close to, but not touching, the fabric.
5.Pull the fabric tight in your free hand and press the button as you move the iron over the fabric.
USING SPRAY
Tip: Use to dampen tough wrinkles at any setting.
1.Be sure the iron is filled with water.
2.On first use, pump the button several times.
ANTI DRIP SYSTEM
The anti drip system prevents water spotting at low temperatures.
DRY IRONING
1. Turn the fabric select dial to setting 1, 2, or 3 to iron without steam.
HOW TO USE (CONT)DRY IRONING
2.To dry iron at higher settings, empty the water from the reservoir to prevent steaming.
EMPTYING WATER TANK (OPTIONAL)
1.Unplug the iron and let it cool.
2.To release the water, hold the iron over a sink with the tip pointing down and to one side. Water will empty out of the water-fill opening.
Model: IR05XC, 6XC, 7XC, 8XC www.prodprotect.com/applica
CARE AND CLEANING
This product contains no user serviceable parts. Refer service to qualified service personnel.
CLEANING OUTSIDE SURFACES
Make sure iron is unplugged and has cooled completely. Wipe the soleplate and outersurfaces with a soft cloth dampened with water. Add mild household detergent. Neve ruse abrasives, heavy-duty cleansers, vinegar or scouring pads that may scratch or discolor the iron. After cleaning, steam iron over an old cloth to remove any residue from the steam vents.
AUTO CLEANTM SYSTEM
Tip: To keep the steam vents free of any buildup, follow these instructions about once a month:
1.Fill the water tank well below the MAX line. Plug in the iron.
2.Turn the fabric select dial to 6 and stand the iron on its heel rest. Allow it to heat.
3.Turn fabric select dial to 0, unplug the iron and hold over a sink with the soleplate facing down.
4.Press and hold the AUTO CLEANTM button. Be careful, as hot water and steam will come out of the steam vents. Continue to hold the AUTO CLEANTM button until
all the water has emptied. If necessary, rock iron side-to-side and front-to-back.
5.When finished, release the button, stand the iron on its heel rest and plug it in. Heat for about 2 minutes to dry out any remaining water.
STORING YOUR IRON
1.Unplug the iron and allow it to cool.
2.Check that the selector is set to 0.
3.Store vertically on its heel to prevent water leaking from the soleplate.
NEED HELP?
For service, repair or any questions regarding your appliance, call the appropriate 800 number on the cover of this book. Do not return the product to the place of purchase. Also, please Do not mail product back to the manufacturer, nor bring it to a service center. You may also want to consult the website listed on the cover of this manual.
Two-Year Limited Warranty
(Applies only in the United States and Canada) What does it cover?
•Any defect in material or workmanship provided; however, Applica’s liability will not exceed the purchase price of the product.
For how long?
•Two years from the date of original purchase with proof of such purchase.
What will we do to help you?
•Provide you with a reasonably similar replacement product that is either new or factory refurbished.
How do you get service?
•Save your receipt as proof of date of sale.
•Check our on-line service site at www.prodprotect.com/applica, or call our toll-free number, 1-800-231-9786, for general warranty service.
•If you need parts or accessories, please call 1-800-738-0245.
What does your warranty not cover?
•Damage from commercial use
•Damage from misuse, abuse or neglect
•Products that have been modified in any way
•Products used or serviced outside the country of purchase
•Glass parts and other accessory items that are packed with the unit
•Shipping and handling costs associated with the replacement of the unit
•Consequential or incidental damages (Please note, however, that some states do not allow the exclusion or limitation of consequential or incidental damages, so this limitation may not apply to you.)
How does state law relate to this warranty?
•This warranty gives you specific legal rights, and you may also have other rights that vary from state to state or province to province.
USA/Canada 1-800-231-9786
Accessories/Parts 1-800-738-0245
Register your product at www.prodprotect.com/applica
Black & Decker Corporation,
Towson, Maryland, USA
Made and Printed in People’s Republic of China
© 2012 Applica Consumer Products, Inc. |
R1 2012/5-15-100E/F |
|
|
|
|
4 |
5 |
6 |
7 |
|
8 |
||||
1 |
2 |
3 |
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
9
13 |
12 |
11 |
10 |
XPRESS STEAM™ IRON
Product may vary slightly from what is illustrated.
1. Spray nozzle |
8. 360° pivoting cord |
|
2. |
Water-fill cover |
9. Slip-resistant heel |
3. |
Fabric select dial |
10. Fabric guide |
4. |
Steam button |
11. Translucent water tank |
5. |
Spray button |
12. Auto CleanTM button |
6. |
Power indicator light |
13. Soleplate |
7. Handle
Loading...