Cisco Systems 3010 User Manual

Size:
8.33 Mb
Download

Cisco IE 3010 Switch Hardware Installation

Guide

Revised October 12, 2012

Americas Headquarters

Cisco Systems, Inc. 170 West Tasman Drive

San Jose, CA 95134-1706USAhttp://www.cisco.com Tel: 408526-4000

800 553-NETS(6387) Fax: 408527-0883

Text Part Number: 78-19581-02

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequencyenergy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be determined by turning the equipment off and on, users are encouraged to try to correct the interference by using one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMEDSUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks.Third-partytrademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

Cisco IE 3010 Switch Hardware Installation Guide

© 2010-2012Cisco Systems, Inc. All rights reserved.

C O N T E N T S

 

Preface vii

 

 

Related Publications i-viii

 

Obtaining Documentation and Submitting a Service Request i-viii

 

Product Overview

 

C H A P T E R 1

1-1

 

Switch Models

1-1

 

Cable Side 1-2

 

10/100 Fast Ethernet Ports

1-3

 

PoE Ports 1-3

 

 

 

 

Dual-Purpose Ports

1-4

 

 

SFP Modules

1-5

 

 

 

SFP Module Patch Cable

1-6

 

Power-Input Terminal

1-6

 

 

Alarm Ports

1-6

 

 

 

 

Alarm Input

1-7

 

 

 

Alarm Output

1-7

 

 

 

Management Ports

1-7

 

 

LEDs 1-8

 

 

 

 

 

Switch Panel LEDs

1-8

 

 

System LED

1-9

 

 

 

Power-Supply Module LEDs

1-9

Alarm LEDs

1-9

 

 

 

Console LEDs

1-10

 

 

Port LEDs

1-10

 

 

 

PoE LED

1-11

 

 

 

Dual-Purpose Port LEDs

1-11

 

SD Flash Memory Card LED

1-11

SD Flash Memory Card

1-11

 

Power-Supply Side

1-12

 

 

 

Power-Supply Side LEDs

1-13

 

Power Supply Features

1-14

 

Management Options

1-14

 

 

 

Network Configurations

1-14

 

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

iii

 

Contents

C H A P T E R 2

Switch Installation 2-1

 

 

Warnings 2-1

 

 

Installation Guidelines

2-3

 

Verifying Switch Operation 2-3

 

Installing the Switch

2-4

 

Rack-Mounting 2-4

 

 

 

 

 

 

 

 

Attaching Brackets for 19-Inch Racks

2-5

 

 

 

Attaching Brackets for 19-Inch Racks for IP-30 Compliance (Optional) 2-6

 

Attaching Brackets for 23-Inch Racks

2-12

 

 

 

Attaching Brackets for ETSI Racks

2-13

 

 

 

Rack-Mounting the Switch

2-14

 

 

 

 

Wall-Mounting 2-15

 

 

 

 

 

 

 

Attaching Brackets

2-16

 

 

 

 

 

 

Attaching Brackets for IP-30 Compliance (Optional)

2-16

 

Wall-Mounting the Switch

2-18

 

 

 

 

Installing and Removing SFP Modules

2-20

 

 

 

 

Installing SFP Modules

2-20

 

 

 

 

 

 

Removing SFP Modules

2-21

 

 

 

 

 

 

Inserting and Removing the SFP Module Patch Cable

2-21

 

 

Removing the SFP Module Patch Cable

2-22

 

 

 

Replacing the SD Flash Memory Card

2-23

 

 

 

 

Connecting Devices to the Ethernet Ports

2-25

 

 

 

Connecting to the 10/100 and 10/100/1000 Ports

2-25

 

 

Connecting to the 10/100 PoE Ports

2-26

 

 

 

Where to Go Next 2-27

 

 

 

 

 

 

 

 

Power Supply Installation

 

 

 

 

 

 

C H A P T E R 3

3-1

 

 

 

 

 

 

Power-Supply Modules

3-1

 

 

 

 

 

 

 

Power-Supply Module Installation 3-3

 

 

 

 

 

Installation Guidelines

3-3

 

 

 

 

 

 

Installing a Power-Supply Module

3-4

 

 

 

 

Equipment That You Need

3-4

 

 

 

 

 

Grounding the Switch 3-4

 

 

 

 

 

 

Installing the Power-Supply Module in the Switch

3-6

 

Wiring the Power Source

3-7

 

 

 

 

 

 

Removing the Power-Supply Module

3-12

 

 

 

Cisco IE 3010 Switch Hardware Installation Guide

 

iv

78-19581-02

 

 

 

Contents

C H A P T E R 4

Troubleshooting 4-1

 

 

 

 

 

 

Diagnosing Problems

4-1

 

 

 

 

 

Switch POST Results

4-1

 

 

 

 

Switch LEDs 4-2

 

 

 

 

 

 

Switch Connections

4-2

 

 

 

 

Bad or Damaged Cable

4-2

 

 

 

Ethernet and Fiber-Optic Cables

4-2

 

 

Link Status

4-2

 

 

 

 

 

10/100 and 10/100/1000 Port Connections

4-3

 

10/100 PoE Port Connections

4-3

 

 

SFP Module

4-3

 

 

 

 

 

Interface Settings

4-3

 

 

 

 

Ping End Device

4-3

 

 

 

 

Spanning Tree Loops

4-4

 

 

 

Switch Performance

4-4

 

 

 

 

Speed, Duplex, and Autonegotiation 4-4

 

 

Autonegotiation and Network Interface Cards

4-4

 

Cabling Distance

4-4

 

 

 

 

 

Resetting the Switch to the Factory Default Settings 4-5

 

 

Finding the Switch Serial Number

4-5

 

 

Technical Specifications

 

 

 

A P P E N D I X

A

 

A-1

 

 

 

Switch Specifications

A-1

 

 

 

Power-Supply Module Specifications A-4

 

 

Alarm Ratings

A-5

 

 

 

 

 

Connector and Cable Specifications

 

A P P E N D I X

B

B-1

 

 

Connector Specifications

B-1

 

 

 

10/100

B-1

 

 

 

 

 

 

SFP Module Connectors B-2

 

 

 

Dual-Purpose Ports

 

B-3

 

 

 

Alarm Port

B-3

 

 

 

 

 

Cables and Adapters

B-4

 

 

 

SFP Module Cables

B-4

 

 

 

Cable Pinouts

B-6

 

 

 

 

Console Port Adapter Pinouts

B-7

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

v

 

Contents

A P P E N D I X C

Configuring the Switch with the CLI Setup Program C-1

 

 

Accessing the CLI Through the Console Port C-1

 

 

RJ-45 Console Port

C-1

 

 

USB Console Port

C-3

 

 

Installing the Cisco Microsoft Windows USB Device Drivers

C-4

 

Installing the Cisco Microsoft Windows XP USB Driver

C-4

 

Installing the Cisco Microsoft Windows 2000 USB Driver

C-4

 

Installing the Cisco Microsoft Windows Vista USB Driver

C-5

 

Uninstalling the Cisco Microsoft Windows USB Drivers C-5

 

 

Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver C-5

 

Uninstalling the Cisco Microsoft Windows Vista USB Driver C-6

Entering the Initial Configuration Information C-7

IP Settings C-7

Completing the Setup Program C-7

I N D E X

Cisco IE 3010 Switch Hardware Installation Guide

 

vi

78-19581-02

 

 

 

Preface

This guide describes the hardware features of the Cisco Industrial Ethernet (IE) 3010 switch. It describes the physical and performance characteristics of the switch, explains how to install it, and provides troubleshooting information.

This guide does not describe system messages that you might receive or how to configure your switch. See the switch software configuration guide, the switch command reference, and the switch system message guide on Cisco.com:

http://www.cisco.com/go/IE3010_docs

Note Meansreader take note. Notes contain helpful suggestions or references to materials not contained in this manual.

Caution Meansreader be careful. In this situation, you might do something that could result in equipment damage or loss of data.

Warning IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071

SAVE THESE INSTRUCTIONS

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

vii

 

Preface

Related Publications

The safety warnings for this product are translated into several languages in the Regulatory Compliance and Safety Information for the Cisco IE 3010 Switch that ships with the product on the documentation CD. The EMC regulatory statements are also included in that guide.

Related Publications

http://www.cisco.com/go/IE3010_docs

Note Before installing, configuring, or upgrading the switch, see the release notes on Cisco.com for the latest information.

Release Notes for the Cisco IE 3010 Switch

Cisco IE 3010 Switch Getting Started Guide

Regulatory Compliance and Safety Information for the Cisco IE 3010 Switch

Cisco IE 3010 Switch Software Configuration Guide

Cisco IE 3010 Switch Command Reference

Cisco IE 3010 Switch System Message Guide

Cisco SFP documents:

http://www.cisco.com/en/US/products/hw/modules/ps5455/prod_installation_guides_list.html

SFP compatibility matrix documents:

http://www.cisco.com/en/US/products/hw/modules/ps5455/products_device_support_tables_list.html

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.

Cisco IE 3010 Switch Hardware Installation Guide

 

viii

78-19581-02

 

 

 

C H A P T E R 1

Product Overview

The Cisco IE 3010 switch provides a rugged and secure switching infrastructure for harsh environments. It is suitable for industrial Ethernet applications, including process manufacturing, intelligent transportation systems (ITSs), rail transportation, and other similar deployments.

In industrial environments, you can connect the switch to any Ethernet-enabledindustrial communication devices, including programmable logic controllers (PLCs),human-machineinterfaces (HMIs), drives, sensors, and input and output (IO) devices.

Switch Models, page 1-1

Cable Side, page 1-2

Power-Supply Side, page 1-12

Management Options, page 1-14

Switch Models

Table 1-1

Switch Models

 

 

 

 

 

 

 

Model

 

 

Description

 

 

 

 

 

Cisco IE-3010-24TC

 

24 10/100 FastEthernet ports, 2 dual-purposeports

 

 

 

 

(2 10/100/1000BASE-Tcopper ports and 2 SFP1 module slots), and

 

 

 

 

2 AC and DC power-supplymodule slots.

 

 

 

 

 

Cisco IE-3010-16S-8PC

 

16 100BASE-FXSFP-moduleslots; 8 10/100 FastEthernet PoE2 ports,

 

 

 

 

2 dual-purposeports (210/100/1000BASE-Tcopper ports and 2 SFP

 

 

 

 

module slots), and 2 AC and DC power-supplymodule slots.

 

 

 

 

 

1.SFP = small form-factorpluggable.

2.PoE = Power over Ethernet.

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

1-1

 

 

 

Chapter 1 Product Overview

Cable Side

Cable Side

The 10/100 Fast Ethernet downlink ports in Figure 1-1 are grouped in pairs. The first member of the pair (port 1) is above the second member (port 2) on the left. Port 3 is above port 4, and so on.

The dual-purposeports are numbered 1 and 2.

Figure 1-1CiscoIE-3010-24TCCable-SideView

1

3

5

6

7

8

Cisco IE 3010

208362

2

4

9

 

 

 

 

 

 

 

1

SD1 flash memory card slot

 

6

RJ-45console port

2

LEDs

 

7

USB (mini-TypeB) console port

 

 

 

 

 

3

Express Setup button

 

8

Power-inputterminal

 

 

 

 

 

4

10/100 ports

 

9

Alarm port

 

 

 

 

 

5

Dual purpose ports

 

 

 

 

 

 

 

 

1. SD = Secure Digital

Cisco IE 3010 Switch Hardware Installation Guide

1-2

78-19581-02

 

 

Chapter 1 Product Overview

Cable Side

The100BASE-FXSFP ports and the 10/100 PoE ports are grouped in pairs. The first member of the pair (port 1) is above the second member (port 2) on the left. Port 3 is above port 4, and so on.

The dual-purposeports are numbered 1 and 2.

Figure 1-2CiscoIE-3010-16S-8PCCable-SideView

1

3

5

6

7

8

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

POW

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ER OVER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ETHERNET

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

POW

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ER OVER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ETHERNET

 

 

 

 

Cisco

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IE 3010

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

4

10

208363

1

SD flash memory card slot

6

Dual purpose ports

 

 

 

 

2

LEDs

7

RJ-45console port

 

 

 

 

3

Express Setup button

8

USB (mini-TypeB) console port

 

 

 

 

4

100BASE-FXSFP ports

9

Power-inputterminal

 

 

 

 

5

10/100 PoE ports

10

Alarm port

 

 

 

 

10/100 Fast Ethernet Ports

You can set the 10/100 ports on the switch to operate in any combination of half duplex, full duplex, or 10 or 100 Mb/s. You can set the ports for speed and duplex autonegotiation. The default setting is autonegotiate.

When set for autonegotiation, the switch determines the speed and duplex settings of the attached device and advertises its own capabilities. If the connected device also supports autonegotiation, the switch negotiates the best connection (the fastest line speed that both devices support and full-duplextransmission if the attached device supports it) and configures itself accordingly. In all cases, the attached device must be within 328 feet (100 meters).

PoE Ports

Warning Voltages that present a shock hazard may exist on Power over Ethernet (PoE) circuits if interconnections are made using uninsulated exposed metal contacts, conductors, or terminals. Avoid using such interconnection methods, unless the exposed metal parts are located within a restricted access location and users and service people who are authorized within the restricted access location are made aware of the hazard. A restricted access area can be accessed only through the use of a special tool, lock and key or other means of security.Statement 1072

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

1-3

 

 

 

Chapter 1 Product Overview

Cable Side

The 10/100 PoE ports on the Cisco IE-3010-16S-8PCswitches provide PoE support for devices that are compliant with IEEE 802.3af. The Cisco prestandard PoE is also supported for Cisco IP Phones and Cisco Aironet Access Points. The PoE ports on the switch deliver up to 15.4 W of PoE. Any four of the eight ports are designated as high priority PoE ports, while the other four ports are designated as low priority PoE ports. When both thepower-supplymodules are installed, the system has enough power to support all eight ports as PoE ports. In case one of thepower-supplymodules fails, the power to the low priority PoE ports is dropped, while power to the high priority PoE ports remains uninterrupted.

On a per-portbasis, you control whether or not a port automatically provides power when an IP phone or an access point is connected.

The 10/100 PoE ports use RJ-45connectors with Ethernet pinouts. The maximum cable length is 328 feet (100 meters). The100BASE-TXand1000BASE-Ttraffic requires Category 5, Category 5e, or Category 6 unshielded twisted pair (UTP) cable. The10BASE-Ttraffic can use Category 3 or Category 4 UTP cable.

For information about configuring and monitoring PoE ports, see the switch software configuration guide on Cisco.com.

For information about port connections and port specifications, see the “Connecting Devices to the Ethernet Ports” section on page 2-25 and the“Connector and Cable Specifications” section on page B-1.

Note The output of the PoE circuit has been evaluated as a Limited Power Source (LPS) per IEC60950-1.

Dual-PurposePorts

You can configure the dual-purposeports on the switch as either 10/100/1000 ports or asSFP-moduleports. You can set the 10/100/1000 ports to autonegotiate, or you can configure them as fixed 10, 100, or 1000 Mb/s (Gigabit) Ethernet ports.

By default, the switch selects the medium for each dual-purposeport(10/100/1000BASE-Tor SFP). When a link is achieved on one media type, the switch disables the other media type until the active link goes down. If links are active on both media, theSFP-moduleport has priority, but you can use themedia-type interface configuration command to manually designate the port as anRJ-45port or an SFP port.

You can configure the speed and duplex settings consistent with the selected media type. For information on configuring interfaces, see the switch software configuration guide.

Cisco IE 3010 Switch Hardware Installation Guide

1-4

78-19581-02

 

 

Chapter 1 Product Overview

Cable Side

SFP Modules

The switch Ethernet SFP modules provide connections to other devices. These field-replaceabletransceiver modules provide the uplink interfaces.The modules have LC connectors forfiber-opticconnections orRJ-45connectors for copper connections. You can use any combination of the supported SFP modules listed inTable 1-2.

Table 1-2Maximum Operating Temperature

Type of SFP Module

Model

 

 

 

Rugged and Industrial SFPs

GLC-SX-MM-RGD

–40to 140°F(–40to 60°C)

GLC-LX-SM-RGD

 

 

GLC-FE-100LX-RGD

 

GLC-FE-100FX-RGD

 

GLC-ZX-SM-RGD

 

 

 

Commercial SFPs

GLC-BX-Dwith DOM support

32 to 113°F (0 to 45°C)

GLC-BX-Uwith DOM support

 

 

GLC-FE-100LX

 

GLC-FE-100BX-D

 

GLC-FE-100BX-U

 

GLC-FE-100FX

 

GLC-FE-100EX

 

GLC-FE-100ZX

 

CWDM SFP with DOM support

 

 

 

Extended temperature SFPs

SFP-GE-Lwith digital optical monitoring

23 to 140°F (–5to 60°C)

 

(DOM) support

 

SFP-GE-Swith DOM support

 

SFP-GE-Zwith DOM support

 

GLC-EX-SMDwith DOM support

 

 

 

For information about SFP modules, see your SFP module documentation and the “Installing and Removing SFP Modules” section on page 2-20.For cable specifications, seeAppendix B, “SFP Module Cables.”

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

1-5

 

 

 

Chapter 1 Product Overview

Cable Side

SFP Module Patch Cable

The switch uses an SFP-modulepatch cable, a0.5-meter,copper, passive cable with SFP module connectors at each end (seeFigure 1-3).The patch cable connects two switches in a cascaded configuration.

Figure 1-3SFP-ModulePatch Cable

See the “Inserting and Removing the SFP Module Patch Cable” section on page 2-21 for information about using the SFP module patch cable.

You can order this cable (part number CAB-SFP-50CM=).

Power-InputTerminal

The power-inputterminal provides screw terminals for the AC and DC power connections. The switch can operate with one or two power supplies. If one of the power sources fail, the other continues to power the switch. SeeChapter 3, “Power Supply Installation,” for information.

Figure 1-4Power-InputTerminal

208415

Alarm Ports

The switch has four alarm inputs and one alarm output. The alarm setting is open or closed.

Open means that the normal condition has current flowing through the contact (referred to as a normally closed contact). The alarm is generated when the current stops.

Closed means that no current flows through the contact (referred to as a normally open contact). The alarm is generated when the current flows.

Cisco IE 3010 Switch Hardware Installation Guide

1-6

78-19581-02

 

 

Chapter 1 Product Overview

Cable Side

Alarm Input

The alarm input is a dry-contactalarm port. You can connect up to four alarm inputs from devices, such as a door, a temperature gauge, or a fire alarm, to the alarm port. You can use the CLI to set the alarm severity to minor, major, or critical. An alarm generates a system message and turns on an LED. See the“Alarm LEDs” section on page 1-9 for the LED descriptions.

Alarm Output

The alarm output can be configured as a minor or major alarm. Output alarms often control an external alarm, such as a bell or a light. To connect an external alarm device to the relay, you connect two relay contact wires to complete the electrical circuit. See Figure B-4 on page B-3 for information on the alarm pinouts.

Management Ports

You can connect the switch to a PC running Microsoft Windows or to a terminal server through either the RJ-45console port or the USB console port.

RJ-45console port. TheRJ-45connection uses anRJ-45-to-DB-9female cable.

USB mini-TypeB console port(5-pinconnector). The USB connection uses a USB TypeA-to-5-pinmini-TypeB cable.

The USB console interface speeds are the same as the RJ-45console interface speeds.

To use the USB console port, you must install the Cisco Windows USB device driver on the device that is connected to the USB console port (device running with Microsoft Windows).

Note For information about downloading the Cisco USB device driver, see the“Installing the Cisco Microsoft Windows USB Device Drivers” section on page C-4.

With the Cisco Windows USB device driver, connecting and disconnecting the USB cable from the console port does not affect Windows HyperTerminal operations. Mac OS X or Linux require no special drivers.

Note The5-pinmini-TypeB connectors resemble the4-pinmini-TypeB connectors. They are not compatible. Use only the5-pinmini-TypeB. SeeFigure 1-5.

Figure 1-5USBMini-TypeB Port

253163

The configurable inactivity timeout reactivates the RJ-45console port if the USB console port is activated, but no input activity occurs on it for a specified time period. When the USB console port deactivates due to a timeout, you can restore its operation by disconnecting and reconnecting the USB cable. For information on using the CLI to configure the USB console interface, see the switch software guide.

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

1-7

 

 

 

Chapter 1 Product Overview

Cable Side

LEDs

You can use the switch system and port LEDs to monitor switch activity and performance.

Switch Panel LEDs

Figure 1-6Switch LEDs (Cable Side)

1

2

3

4

5

6

7

8

9

10 11

12

13

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

16

207198

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

14

15

 

 

 

 

 

 

 

 

 

1

SYS (system)

 

 

 

9

OUT (alarm output)

 

 

 

 

 

 

 

 

2

CON (RJ-45console)

 

 

 

10

PSU1 (power supply 1)

 

 

 

 

 

 

 

 

3

USB (mini-USBconsole)

 

 

 

11

PSU2 (power supply 2)

 

 

 

 

 

 

 

 

4

SD (SD flash memory card)

 

 

 

12

PoE1

5

IN1 (alarm input 1)

 

 

 

13

Express Setup button

 

 

 

 

 

 

 

 

6

IN2 (alarm input 2)

 

 

 

14

Ethernet ports

 

 

 

 

 

 

 

 

7

IN3 (alarm input 3)

 

 

 

15

SFP module port

 

 

 

 

 

 

 

 

8

IN4 (alarm input 4)

 

 

 

16

10/100/1000 port

 

 

 

 

 

 

 

 

1. Only on the Cisco IE-3010-16S-8PCswitch.

Cisco IE 3010 Switch Hardware Installation Guide

1-8

78-19581-02

 

 

Chapter 1 Product Overview

Cable Side

System LED

Table 1-3

System LED

 

 

 

Color

 

System Status

 

 

 

Off

 

System is not powered on.

 

 

 

Blinking green

 

POST1 is in progress.

Green

 

System is operating normally.

 

 

 

Amber

 

System is receiving power but is not functioning properly.

 

 

 

1. POST = power-onself-test.

Power-SupplyModule LEDs

The switch power-supplymodule LEDs are labeled PSU1 and PSU2 (on the switch) and PSU OK (on thepower-supplymodule). They show whetherpower-supplymodules 1 and 2 are receiving power. SeeFigure 1-6 andFigure 1-9.

Table 1-4

Power-SupplyModule LEDs

 

 

 

Color

 

System Status

 

 

 

Off

 

Power-supplymodule (1 or 2) is not installed.

 

 

 

Green

 

Valid input is present, and the output is within the operating range.

 

 

 

Red

 

Valid input is present, and the output is outside the operating range or is not present.

 

 

 

Blinking red

 

Valid input is not present.

 

 

 

Alarm LEDs

Table 1-5

Alarm Input LEDs

 

 

 

 

Color

 

System Status

 

 

 

 

Off

 

No alarm

 

 

 

 

Amber

 

Minor alarm

 

 

 

 

Red

 

Major alarm

 

 

 

 

Blinking red

 

Critical alarm

 

 

 

 

Table 1-6

Alarm Output LED

 

 

 

Color

 

System Status

 

 

 

Green

 

No alarm

 

 

 

Red

 

Relay closed, alarm present

 

 

 

 

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

1-9

 

 

 

Chapter 1 Product Overview

Cable Side

Console LEDs

The console LEDs show which console port is in use. See Figure 1-6 andFigure 1-9 for the LED locations.

If you connect a cable to a console port, the switch automatically uses that port for console communication. If you connect two console cables, the USB console port has priority.

Table 1-7

RJ-45and USB Console Port LEDs

 

 

 

 

LED

 

Color

Description

 

 

 

RJ-45console port

Green

RJ-45console port is active.

 

 

 

USB console port LED is off.

 

 

 

 

 

 

Off

Port is not active.

 

 

 

USB console port is active.

 

 

 

USB console port

Green

USB console port is active.

 

 

 

RJ-45console port LED is off.

 

 

 

 

 

 

Off

Port is not active.

 

 

 

RJ-45console port is active.

 

 

 

 

Port LEDs

RJ-45ports andSFP-moduleslots have port LEDs. Port LEDs, as a group or individually, provide information about the switch and about the individual ports.

Table 1-8

Meaning of Port LED Colors

 

 

 

LED Color

 

Meaning

 

 

 

Off

 

No link or port was administratively shut down.

 

 

 

Green

 

Link present but not sending or receiving data.

 

 

 

Blinking green

 

Activity. Port is sending or receiving data.

 

 

 

Alternating

 

Link fault. Error frames can affect connectivity, and errors such as excessive

green-amber

 

collisions, CRC errors, and alignment and jabber errors are monitored for link

 

 

faults.

 

 

 

Amber

 

Port is blocked by Spanning Tree Protocol (STP) and is not forwarding data.

 

 

After a port is reconfigured, the port LED is amber for up to 30 seconds as STP

 

 

searches for loops.

 

 

 

Cisco IE 3010 Switch Hardware Installation Guide

1-10

78-19581-02

 

 

Chapter 1 Product Overview

Cable Side

PoE LED

Table 1-9

PoE LED

 

 

 

Color

 

Meaning

 

 

 

Off

 

PoE is not enabled.

 

 

 

Green

 

PoE is enabled. Ports are functioning correctly.

 

 

 

Amber

 

PoE is enabled, but an error is present.

 

 

 

Dual-PurposePort LEDs

The dual-purposeport LEDs identify the connection as either acopper-basedconnector or an SFP module. The ports can autonegotiate, or you can manually configure eachdual-purposeport as either 10/100/1000 with copper connectors or as anSFP-moduleport, but not as both types at the same time. SeeTable 1-8 for LED descriptions.

SD Flash Memory Card LED

Table 1-10

SD Flash Memory Card LED

 

 

 

Color

 

System Status

 

 

Off / blinking green

SD flash memory card transfer in progress.

 

 

 

Blinking amber

 

SD flash memory card is not present (slow blinking).

 

 

Unsupported SD flash memory card is detected (fast blinking).

 

 

 

Amber

 

Error accessing the SD flash memory card.

 

 

Cisco IOS boot image cannot be found.

 

 

 

Green

 

SD flash memory card is functioning.

 

 

 

SD Flash Memory Card

The switch ships with the Secure Digital (SD) flash memory card installed. See Figure 1-1 andFigure 1-2.The switch stores the Cisco IOS software images and the switch configuration on the card.

You should not remove the card unless you want to use it in a replacement switch. You then do not have to reconfigure the new switch. See the “Replacing the SD Flash Memory Card” section on page 2-23 for information.

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

1-11

 

 

 

Chapter 1 Product Overview

Power-SupplySide

Power-SupplySide

The power-supplyside has the LED panel and twopower-supplyslots for the removable power supplies. SeeFigure 1-7 andFigure 1-8.

Figure 1-7Switch with OnePower-SupplyModule

Cisco IE

3010

Sw

 

 

itchSeries

 

 

-DC

 

 

PW R-RGD-LOW

 

 

2

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

1

LED panel

 

3

Power-supplyslot 2

 

 

 

 

 

2

Power-supplyslot 1

 

 

 

 

 

 

 

 

 

Figure 1-8

Switch with Both Power-SupplyModules

Cisco IE

3010

Sw

 

 

itchSeries

PW R-RGD-LOW-DC

PW R-RGD-LOW-DC

1

1

1 PSU OK LED

For a description of the PSU OK LED, see Table 1-4 on page 1-9.

Cisco IE 3010 Switch Hardware Installation Guide

1-12

78-19581-02

 

 

Chapter 1 Product Overview

Power-SupplySide

Power-SupplySide LEDs

Figure 1-9

 

Switch LEDs

 

 

 

1

2

3

4

5

6

7

8

9

10 11

12

Cisco IE 3010

Switch Series

 

 

 

 

 

 

 

 

 

208364

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

15

 

 

 

 

 

 

 

 

 

 

 

13

 

14

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

SYS (system)

 

 

 

 

9

OUT (alarm output)

 

 

 

 

 

 

 

 

 

 

 

 

2

CON (console)

 

 

 

 

10

PSU1 (power supply 1)

 

 

 

 

 

 

 

 

 

 

 

 

3

USB LED

 

 

 

 

11

PSU2 (power supply 2)

 

 

 

 

 

 

 

 

 

 

 

 

4

SD (SD flash memory card)

 

 

 

 

12

PoE1

5

IN1 (alarm input 1)

 

 

 

 

13

Ethernet ports

 

 

 

 

 

 

 

 

 

 

 

 

6

IN2 (alarm input 2)

 

 

 

 

14

10/100/1000 port

 

 

 

 

 

 

 

 

 

 

 

 

7

IN3 (alarm input 3)

 

 

 

 

15

SFP port

 

 

 

 

 

 

 

 

 

 

 

 

8

IN4 (alarm input 4)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1. Only on the Cisco IE-3010-16S-8PCswitch.

For a description of the LEDs, see the “LEDs” section on page 1-8.

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

1-13

 

 

 

Chapter 1 Product Overview

Management Options

Power Supply Features

The switch has two slots for power-supplymodules:

PWR-RGD-LOW-DC/IA:low-voltageDC (for voltage information, seeTable A-6)

PWR-RGD-AC-DC/IA:high-voltageAC or DC (for voltage information, seeTable A-5)The switch supports thesepower-supplymodule combinations:

Single low-voltageDC

Single high-voltageAC or DC

Two high-voltageAC or DC

Two low-voltageDC

One high-voltageAC or DC and onelow-voltageDC

For information on installing the power-supplymodules, seeChapter 3, “Power Supply Installation.” SeeTable 1-4 for information on the power supply LEDs.

Management Options

Cisco IOS CLI

You can configure and monitor the switch from the CLI. Connect your management station to the switch console port or use Telnet from a remote management station. See the switch command reference on Cisco.com for information.

SNMP network management

You can manage switches from a Simple Network Management Protocol (SNMP)-compatiblemanagement station that is running platforms such as HP OpenView or SunNet Manager. The switch supports a comprehensive set of Management Information Base (MIB) extensions and four Remote Monitoring (RMON) groups. See the switch software configuration guide on Cisco.com and the documentation that came with your SNMP application for information.

Network Configurations

See the switch software configuration guide on Cisco.com for an explanation of network configuration concepts. The software configuration guide also provides network configuration examples for creating dedicated network segments that are interconnected through Ethernet connections.

Cisco IE 3010 Switch Hardware Installation Guide

1-14

78-19581-02

 

 

C H A P T E R 2

Switch Installation

Read the topics and perform the procedures in this order:

Warnings, page 2-1

Installation Guidelines, page 2-3

Verifying Switch Operation, page 2-3

Installing the Switch, page 2-4

Installing and Removing SFP Modules, page 2-20

Inserting and Removing the SFP Module Patch Cable, page 2-21

Replacing the SD Flash Memory Card, page 2-23

Connecting Devices to the Ethernet Ports, page 2-25

Where to Go Next, page 2-27

Warnings

These warnings are translated into several languages in the Regulatory Compliance and Safety Information for the Cisco IE 3010 Switch document that ships on the documentation CD.

These warning statements apply to all the switches:

Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals.Statement 43

Warning Read the installation instructions before you connect the system to its power source.Statement 1004

Warning This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security.

Statement 1017

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

2-1

 

 

 

Chapter 2 Switch Installation

Warnings

Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available.Statement 1024

Warning This unit might have more than one power supply connection. All connections must be removed tode-energizethe unit.Statement 1028

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Warning Ultimate disposal of this product should be handled according to all national laws and regulations.

Statement 1040

Warning For connections outside the building where the equipment is installed, the following ports must be connected through an approved network termination unit with integral circuit protection. 10/100/1000 EthernetStatement 1044

Warning To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of:

140°F (60°C) Statement 1047

Warning Installation of the equipment must comply with local and national electrical codes.Statement 1074

Note For U.S. installations, refer to national electrical code ANSI/NFPA 70.

Warning To prevent airflow restriction, allow clearance around the ventilation openings to be at least: 1.75 in. (4.4 cm).Statement 1076

Warning Avoid using or servicing any equipment that has outdoor connections during an electrical storm. There may be a risk of electric shock from lightning.Statement 1088

Cisco IE 3010 Switch Hardware Installation Guide

2-2

78-19581-02

 

 

Chapter 2 Switch Installation

Installation Guidelines

Installation Guidelines

Before installing the switch, verify that these guidelines are met:

Cabling is away from sources of electrical noise, such as radios, power lines, and fluorescent lighting fixtures. Make sure that the cabling is away from other devices that might damage the cables.

Operating environment is within the ranges listed in Appendix A, “Technical Specifications.”

Relative humidity around the switch does not exceed 95 percent (noncondensing).

Altitude at the installation site is not higher than 10,000 feet.

For 10/100 and 10/100/1000 fixed ports, cable lengths from the switch to connected devices are not more than 328 feet (100 meters).

For cable lengths for small form-factorpluggable(SFP)-moduleconnections, see the“SFP Module Cables” section on page B-4 and the module documentation.

Airflow around the switch and through the vents is unrestricted. To prevent overheating, the switch must meet the minimum clearance of 1.75 inches (4.4 cm) at the top and bottom.

Note If the switch is installed in a closed or multirack assembly, the temperature around it might be greater than normal room temperature.

Verifying Switch Operation

Before installing the switch in a rack or on a wall, you should power the switch and verify that the switch passes the power-onself-test(POST).

To wire the switch to the power source, see Chapter 3, “Power Supply Installation.”

When the switch begins POST, the SYS LED blinks green, and the other LEDs stay green. When the switch passes POST, the SYS LED turns green. The other LEDs turn off and return to their operating status. If the switch fails POST, the SYS LED is amber.

Note Contact Cisco Systems immediately if your switch fails POST.

After a successful POST, disconnect the power from the switch. For more information, see Chapter 3, “Power Supply Installation.” See the“Installing the Switch” section on page 2-4 to install the switch in a rack or on a wall.

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

2-3

 

 

 

Chapter 2 Switch Installation

Installing the Switch

Installing the Switch

Rack-Mounting, page 2-4

Wall-Mounting, page 2-15

Note If the switch iswall-mountedin an enclosure, follow these minimum clearances:

-Sides of switch (facing up and facing down): 3.75 in. (9.52 cm)

-Port side 3.0 in. (7.62 cm)

-Power supply side: 5.25 in. (13.33 cm)

-Cover side (side not facing wall): 1.75 in. (4.44 cm)

-Base side (facing wall): 0 in. (0 cm)

Rack-Mounting

To rack-mountthe switch, select the rack size and follow the steps in these sections:

Attaching Brackets for 19-Inch Racks, page 2-5

Attaching Brackets for 19-Inch Racks for IP-30 Compliance (Optional), page 2-6

Attaching Brackets for 23-Inch Racks, page 2-12

Attaching Brackets for ETSI Racks, page 2-13

Rack-Mounting the Switch, page 2-14

.

Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety:

This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack.

If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. Statement 1006

Warning For mountingrailway-applicationequipment and for EN50155 standard compliance, the switch must be installed only in a rackmid-mountingposition. If you install the switch in a frontrack-mounting(cable side or power supply side) position or in awall-mountingposition, a mechanical failure can occur that results in the switch becoming detached from the rack.Statement 403

Cisco IE 3010 Switch Hardware Installation Guide

2-4

78-19581-02

 

 

Chapter 2 Switch Installation

Installing the Switch

Attaching Brackets for 19-InchRacks

Figure 2-1 andFigure 2-2 show how to attach brackets to the switches.

Figure 2-1Attaching Brackets for19-InchRacks

Cisco IE 3010

1

2

Cisco IE 3010

3

2

 

 

 

208366

 

 

 

4

 

 

 

2

 

 

 

 

1

Mid-mountingposition

3

Cable-sidemounting position

 

 

 

 

2

Phillips flat-headscrews

4

Power-supply-sidemounting position

 

 

 

 

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

2-5

 

 

 

Chapter 2 Switch Installation

Installing the Switch

Figure 2-2Attaching Brackets for19-InchRacks

Cisco CGS 2520

2

1

 

 

 

207231

 

 

 

3

 

 

 

1

 

 

 

 

1

Phillips flat-headscrews

3

Power-supply-sidemounting position

 

 

 

 

2

Cable-side-mountingposition

 

 

 

 

 

 

Attaching Brackets for 19-InchRacks forIP-30Compliance (Optional)

Before installing the mounting brackets, you need to install the rubber plugs in the unused mounting holes. The rubber plugs are not supplied with the switch. You can order a kit (part number IE-3010-IP30KIT)containing the rubber plugs.

You can order a kit (part number IE-3010-IP30KIT)that contains the rubber plugs.

Figure 2-3 shows aclose-upof the rubber plug. You can install the rubber plugs in the holes as shown inFigure 2-4 andFigure 2-5.

Cisco IE 3010 Switch Hardware Installation Guide

2-6

78-19581-02

 

 

Chapter 2 Switch Installation

Installing the Switch

Figure 2-3Inserting the Rubber Plug

1

2

 

 

 

3

 

 

 

255738

 

1

Rubber plug

3 Screwdriver

 

2

Switch

 

Step 1

Identify your bracket mounting position. See Figure 2-6 orFigure 2-7.

Step 2

Insert the rubber plugs in the appropriate holes. See Figure 2-4 orFigure 2-5.Follow the same procedure

 

on the other side of the switch.

 

Step 3

Use a screwdriver or pen to completely push in the rubber plugs. See Figure 2-3.

Step 4

Install the brackets on both sides of the switch. See Figure 2-6 orFigure 2-7.

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

2-7

 

 

 

Chapter 2 Switch Installation

Installing the Switch

Figure 2-4Inserting the Rubber Plugs

2

1

3

1

 

 

 

 

 

 

255739

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

1

Rubber plug

 

 

3

 

Cable-sidemounting position

 

 

 

 

 

 

 

2

Mid-mountingposition

 

 

4

 

Power-supply-sidemounting position

 

 

 

 

 

 

 

Cisco IE 3010 Switch Hardware Installation Guide

2-8

78-19581-02

 

 

Chapter 2 Switch Installation

Installing the Switch

Figure 2-5Inserting the Rubber Plugs

CiscoCGS2520

2

1

255740

 

 

3

 

 

1

 

 

 

 

 

 

1

Rubber plug

 

3

Power-supply-sidemounting position

 

 

 

 

 

2

Cable-side-mountingposition

 

 

 

 

 

 

 

 

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

2-9

 

 

 

Chapter 2 Switch Installation

Installing the Switch

Figure 2-6Attaching Brackets for19-InchRacks

2

1

3

2

 

 

 

 

 

 

255750

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

Mid-mountingposition

3

 

 

Cable-sidemounting position

 

 

 

 

 

 

 

 

2

Phillips flat-headscrews

4

 

 

Power-supply-sidemounting position

 

 

 

 

 

 

 

 

Cisco IE 3010 Switch Hardware Installation Guide

2-10

78-19581-02

 

 

Chapter 2 Switch Installation

Installing the Switch

Figure 2-7Attaching Brackets for19-InchRacks

Cisco CGS 2520

2

1

 

PSU2

 

 

 

 

 

 

 

 

 

 

 

 

255751

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

Phillips flat-headscrews

3

Power-supply-sidemounting position

 

 

 

 

 

 

 

 

2

Cable-side-mountingposition

 

 

 

 

 

 

 

 

 

 

 

 

 

Note ForIP-30compliance: If you use23-inchbrackets or ETSI brackets, you can insert the rubber plugs in the same holes as shown inFigure 2-4 orFigure 2-5 before installing the brackets.

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

2-11

 

 

 

Chapter 2 Switch Installation

Installing the Switch

Attaching Brackets for 23-InchRacks

Figure 2-8Attaching23-InchBrackets

Cisco

2

Cisco

2

1

3

1

1

Cisco

 

 

 

 

1

2

 

 

 

 

 

 

 

 

 

 

 

 

279173

 

 

 

 

1

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

Phillips flat-headscrews

 

3

Power-supply-sidemounting position

 

 

 

 

 

 

 

2

Cable-side-mountingposition

 

 

 

 

 

 

 

 

 

 

Note ForIP-30compliance: If you use23-inchbrackets, you can insert the rubber plugs in the same holes as shown inFigure 2-4 orFigure 2-5 before installing the brackets.

Cisco IE 3010 Switch Hardware Installation Guide

2-12

78-19581-02

 

 

Chapter 2 Switch Installation

Installing the Switch

Attaching Brackets for ETSI Racks

Figure 2-9Attaching Brackets for ETSI Racks

Cisco CGS 2520

2

Cisco CGS 2520

2

1

3

1

1

Cisco CGS 2520

 

 

2

 

 

 

1

 

 

 

 

279174

 

 

3

 

 

 

1

 

 

 

 

 

 

 

1

Phillips flat-headscrews

 

3

Power-supply-sidemounting position

 

 

 

 

 

2

Cable-side-mountingposition

 

 

 

 

 

 

 

 

Note ForIP-30compliance: If you use ETSI brackets, you can insert the rubber plugs in the same holes as shown inFigure 2-4 orFigure 2-5 before installing the brackets.

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

2-13

 

 

 

Chapter 2 Switch Installation

Installing the Switch

Rack-Mountingthe Switch

After you attach the brackets on the switch, use the four supplied number-12Phillips machine screws to attach the brackets to the rack. SeeFigure 2-10.

Figure 2-10

Rack-Mounting

1

4

6

2

3

Cisco

 

 

IE 3010

4

Cisco IE

3010

Sw

 

 

itchSeries

5

 

 

 

4

 

 

 

 

 

1

Mid-mountingposition

4

 

Phillips machine screws

 

 

 

 

 

2

Cable screw

5

 

Power-supply-sidemounting position

 

 

 

 

 

3

Cable-sidemounting position

6

 

Cable guide

 

 

 

 

 

208367

Cisco IE 3010 Switch Hardware Installation Guide

2-14

78-19581-02

 

 

Chapter 2 Switch Installation

Installing the Switch

After the switch is mounted in the rack:

Wire the switch to a power source. See Chapter 3, “Power Supply Installation.”

Connect the ports. See the “Connecting Devices to the Ethernet Ports” section on page 2-25.

We recommend attaching the cable guide to prevent the cables from obscuring the LED panels on the devices in the rack. Use the supplied black screw shown in Figure 2-10 to attach the cable guide to the left or right bracket.

For configuration instructions about the CLI setup program, go to Appendix C, “Configuring the Switch with the CLI Setup Program.”

Wall-Mounting

To wall-mountthe switch, follow the steps in these sections:

Attaching Brackets, page 2-16

Attaching Brackets for IP-30 Compliance (Optional), page 2-16

Wall-Mounting the Switch, page 2-18

Warning Read thewall-mountinginstructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system.Statement 378

Warning For mountingrailway-applicationequipment and for EN50155 standard compliance, the switch must be installed only in a rackmid-mountingposition. If you install the switch in a frontrack-mounting(cable side or power supply side) position or in awall-mountingposition, a mechanical failure can occur that results in the switch becoming detached from the rack.Statement 403

Note If the switch iswall-mountedin an enclosure, follow these minimum clearances:

-Sides of switch (facing up and facing down): 3.75 in. (9.52 cm)

-Port side 3.0 in. (7.62 cm)

-Power supply side: 5.25 in. (13.33 cm)

-Cover side (side not facing wall): 1.75 in. (4.44 cm)

-Base side (facing wall): 0 in. (0 cm)

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

2-15

 

 

 

Chapter 2 Switch Installation

Installing the Switch

Attaching Brackets

Figure 2-11Attaching19-inchRack Brackets

1

SeriesitchSw

3010IEiscoC

 

208368

1 Phillipstruss-headscrews

Attaching Brackets for IP-30Compliance (Optional)

Step 1 Insert the rubber plugs in the appropriate holes. SeeFigure 2-12.Follow the same procedure on the other side of the switch.

Note The rubber plugs are not supplied with the switch. You can order a kit (part number

IE-3010-IP30KIT)containing the rubber plugs.

Step 2 Use a screwdriver or pen to completely push in the rubber plugs. SeeFigure 2-3.

Step 3 Install the brackets on both sides of the switch. SeeFigure 2-13.

Cisco IE 3010 Switch Hardware Installation Guide

2-16

78-19581-02

 

 

Chapter 2 Switch Installation

Installing the Switch

Figure 2-12Inserting the Rubber Plugs in the Switch Holes

1

2

itchSw

Cisco

Series

3010IE

255741

1Rubber plug

2Switch-side

Figure 2-13Attaching19-inchRack Brackets

1

3010IE Cisco

SeriesSwitch

255752

1 Phillipstruss-headscrews

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

2-17

 

 

 

Chapter 2 Switch Installation

Installing the Switch

Wall-Mountingthe Switch

For the best support of the switch and cables, make sure that the switch is attached securely to wall studs or to a firmly attached plywood mounting backboard.

Mount the switch with the side panel facing up. The Cisco logo should be at the top of the switch. See Figure 2-14 andFigure 2-15.

Figure 2-14Wall-Mountingthe CiscoIE-3010-24TC

1

SeriesitchSw

3010IEiscoC

 

 

 

 

208369

1 User-suppliedscrews

Cisco IE 3010 Switch Hardware Installation Guide

2-18

78-19581-02

 

 

Chapter 2 Switch Installation

Installing the Switch

Figure 2-15Wall-Mountingthe CiscoIE-3010-16S-8PC

1

Series2500itchSw

ridG ConnectediscoC

 

 

 

 

207557

After the switch is mounted on the wall:

Wire the switch to a power source. See Chapter 3, “Power Supply Installation.”

For configuration instructions about using the CLI setup program, go to Appendix C, “Configuring the Switch with the CLI Setup Program.”

Connect the switch ports. See the “Connecting Devices to the Ethernet Ports” section on page 2-25.

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

2-19

 

 

 

Chapter 2 Switch Installation

Installing and Removing SFP Modules

Installing and Removing SFP Modules

Installing SFP Modules

When installing SFP modules, observe these guidelines:

Removing and installing an SFP module can shorten its useful life. Do not remove and insert any module more often than is absolutely necessary.

To prevent ESD damage, follow your normal board and component handling procedures when connecting cables to the switch and other devices.

Warning Class 1 laser product.Statement 1008

Step 1 Attach anESD-preventivewrist strap to your wrist and to a bare metal surface.

Step 2 Find the send (TX) and receive (RX) markings on the module top.

On some SFP modules, the send and receive (TX and RX) markings might be replaced by arrows that show the direction of the connection, either send or receive (TX or RX).

Step 3 If the module has abale-clasplatch, move it to the open, unlocked position.

Step 4 Align the module in front of the slot opening, and push until you feel the connector snap into place.

Step 5 If the module has abale-clasplatch, close it.

Step 6 Forfiber-opticSFP modules, remove the dust plugs and save.

Step 7 Connect the SFP cables.

Figure 2-16Installing an SFP Module

Cisco IE 3010

208370

Caution Do not remove the dust plugs from thefiber-opticSFP module port or the rubber caps from thefiber-opticcable until you are ready to connect the cable. The plugs and caps protect the SFP module ports and cables from contamination and ambient light.

Cisco IE 3010 Switch Hardware Installation Guide

2-20

78-19581-02

 

 

Chapter 2 Switch Installation

Inserting and Removing the SFP Module Patch Cable

Removing SFP Modules

Step 1 Attach anESD-preventivewrist strap to your wrist and to a bare metal surface.

Step 2 Disconnect the cable from the SFP module. For reattachment, note which cable connector plug is send (TX) and which is receive (RX).

Step 3 Insert a dust plug into the optical ports of the SFP module.

Step 4 If the module has abale-clasplatch, pull the bale out and down to eject it. If the latch is obstructed and you cannot use your finger, use a small,flat-bladescrewdriver or other long, narrow instrument.

Step 5 Grasp the SFP module, and carefully remove it from the slot.

Step 6 Place the module in an antistatic bag or other protective environment.

Figure 2-17Removing aBale-ClaspLatch SFP Module

Cisco IE 3010

1

208371

1 Bale clasp

Inserting and Removing the SFP Module Patch Cable

Step 1 Attach anESD-preventivewrist strap to your wrist and to a bare metal surface.

Step 2 Insert the SFP module patch cable in the slot until you feel the connector on the cable snap into place at the rear of the slot (seeFigure 2-18).

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

2-21

 

 

 

Chapter 2 Switch Installation

Inserting and Removing the SFP Module Patch Cable

Figure 2-18Inserting an SFP Module Patch Cable

Ci

 

 

sco IE

3010

208372

 

 

 

Step 3 Repeat these steps for the second switch that you want to connect to the first switch.

Figure 2-19Connecting Two Switches with an SFP Module Patch Cable

POW EROVER ETHERNET

Cisco IE 3010

Cisco IE 3010

208373

Removing the SFP Module Patch Cable

To remove an SFP module patch cable from the SFP module slot, release the connector, and pull it from the slot.

Cisco IE 3010 Switch Hardware Installation Guide

2-22

78-19581-02

 

 

Chapter 2 Switch Installation

Replacing the SD Flash Memory Card

Replacing the SD Flash Memory Card

Step 1 Locate the SD flash memory card slot on thecable-sideof the switch.

Step 2 Use anumber-1Phillips screwdriver to loosen the captive screw. SeeFigure 2-20.

Figure 2-20Loosening the Captive Screw

208563

Step 3 Pull the cover open, and pull the cover tab from the hinge. SeeFigure 2-21.

Figure 2-21Removing the SD Slot Cover

208566

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

2-23

 

 

 

Chapter 2 Switch Installation

Replacing the SD Flash Memory Card

Step 4 Gently push the SD flash memory card to eject it. SeeFigure 2-22.Place it in an antistatic bag to protect it from static discharge.

Figure 2-22Removing the SD Flash Memory Card

.

208564

Step 5 Push the replacement card (upside down) into the slot, and press it firmly in place. The card is keyed so that you cannot insert it the wrong way.

Step 6 Place the SD slot cover tabs into the hinge.

Step 7 Close the cover, and use a ratcheting torquenumber-1Phillips screwdriver to torque the screw to 4.5in-lb.

Cisco IE 3010 Switch Hardware Installation Guide

2-24

78-19581-02

 

 

Chapter 2 Switch Installation

Connecting Devices to the Ethernet Ports

Connecting Devices to the Ethernet Ports

Connecting to the 10/100 and 10/100/1000 Ports, page 2-25

Connecting to the 10/100 PoE Ports, page 2-26

Connecting to the 10/100 and 10/100/1000 Ports

The 10/100 and 10/100/1000 Ethernet ports use standard RJ-45connectors with Ethernet pinouts. The maximum cable length is 328 feet (100 meters). The100BASE-TXand1000BASE-Ttraffic requires Category 5, Category 5e, or Category 6 UTP cable. The10BASE-Ttraffic uses Category 3 or Category 4 cable.

The autonegotiation feature is enabled by default on the switch. At this setting, the switch ports configure themselves to operate at the speed of the attached device. If the device does not support autonegotiation, you can set the switch port speed and duplex parameters. To maximize performance, either let the ports autonegotiate both speed and duplex, or set the port speed and duplex parameters on both ends of the connection.

For simplified cabling, the automatic medium-dependentinterface crossover(auto-MDIX)feature is enabled by default. Withauto-MDIXenabled, the switch detects the required cable type for copper Ethernet connections and configures the interface accordingly. Therefore, you can use either a crossover or astraight-throughcable for connections to a 10/100/1000 Ethernet port, regardless of the type of connected device.

See the switch software configuration guide or the switch command reference on Cisco.com for more information about autonegotiation and auto-MDIX.

If auto-MDIXis disabled, use the guidelines inTable 2-1 to select the cable for connecting the 10/100/1000 Ethernet ports to other devices. See the“Connector and Cable Specifications” section on page B-1 forcable-pinoutdescriptions. SeeFigure 2-23.

Figure 2-23Connecting to an Ethernet Port

207211

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

2-25

 

 

 

Chapter 2 Switch Installation

Connecting Devices to the Ethernet Ports

Table 2-1

Ethernet Cables (Auto-MDIXDisabled)

 

 

 

 

Device

 

Crossover Cable1

Straight-ThroughCable1

Switch to switch

Yes

No

 

 

 

 

Switch to hub

 

Yes

No

 

 

 

Switch to computer or server

No

Yes

 

 

 

 

Switch to router

 

No

Yes

 

 

 

Switch to IP phone

No

Yes

 

 

 

 

1.100BASE-TXand1000BASE-Ttraffic requires twistedfour-pair,Category 5, Category 5e, or Category 6 cable.10BASE-Ttraffic uses Category 3 or Category 4 cable.

Connecting to the 10/100 PoE Ports

The Cisco IE-3010-16S-8PCswitch 10/100 PoE ports have the same autonegotiation settings and cabling requirements as those in the“Connecting to the 10/100 and 10/100/1000 Ports” section on page 2-25.These ports provide PoE power.

See the “PoE Ports” section on page 1-3 for information on the cables and connectors.

The ports provide PoE support for devices compliant with IEEE 802.3af and also provide Cisco prestandard PoE support for Cisco IP Phones and Cisco Aironet Access Points.

On a per-portbasis, you can control whether or not a port automatically provides power to a connected IP phone or an access point.

To access an advanced PoE planning tool, use the Cisco Power Calculator on Cisco.com:

http://tools.cisco.com/cpc/launch.jsp

You can use this application to calculate the power supply requirements for a specific PoE configuration. The results show output current, output power, and heat dissipation.

Warning Voltages that present a shock hazard may exist on Power over Ethernet (PoE) circuits if interconnections are made using uninsulated exposed metal contacts, conductors, or terminals. Avoid using such interconnection methods, unless the exposed metal parts are located within a restricted access location and users and service people who are authorized within the restricted access location are made aware of the hazard. A restricted access area can be accessed only through the use of a special tool, lock and key or other means of security.Statement 1072

Caution Category 5e and Category 6 cables can store high levels of static electricity. Always ground the cables to a suitable and safe earth ground before connecting them to the switch or other devices.

Cisco IE 3010 Switch Hardware Installation Guide

2-26

78-19581-02

 

 

Chapter 2 Switch Installation

Where to Go Next

Where to Go Next

You can use the default configuration or use any of the management options described in the “Management Options” section on page 1-14 to change the switch settings.

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

2-27

 

 

 

Chapter 2 Switch Installation

Where to Go Next

Cisco IE 3010 Switch Hardware Installation Guide

2-28

78-19581-02

 

 

C H A P T E R 3

Power Supply Installation

This chapter describes how to remove and install a new or replacement power supply. Your switch ships with at least one installed power-supplymodule (AC or DC, depending on your order).

The power-supplymodules arefield-replaceableunits (FRUs) and arehot-swappable.

For translations of the safety warnings in this chapter, see the Regulatory Compliance and Safety Information for the Cisco IE 3010 Switch on the documentation CD and also on Cisco.com.

Power-Supply Modules, page 3-1

Installation Guidelines, page 3-3

Grounding the Switch, page 3-4

Installing the Power-Supply Module in the Switch, page 3-6

Wiring the Power Source, page 3-7

Removing the Power-Supply Module, page 3-12

Power-SupplyModules

For information on the power-supplymodules, see the“Power Supply Features” section on page 1-14.

Table 3-1

Power-SupplyModules

 

 

 

Model

 

Description

 

 

PWR-RGD-LOW-DC/IA

Low-voltageDC. For voltage information, seeTable A-6 on page A-4.

 

 

PWR-RGD-AC-DC/IA

High-voltageAC or DC. For voltage information, seeTable A-5 on

 

 

page A-4.

 

 

 

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

3-1

 

 

 

Chapter 3 Power Supply Installation

Power-SupplyModules

Figure 3-1PWR-RGD-AC-DC/IAPower-SupplyModule

1

 

 

 

207215

 

 

2

 

 

 

 

3

1

Power-supplymodule3

Captive screw

2

PSU OK LED

 

Figure 3-2

PWR-RGD-LOW-DC/IAPower-SupplyModule

 

 

1

 

 

LOW-DC

 

 

 

PWR-RGD-

 

207232

2

3

1 Power-supplymodule

3 Captive screw

2 PSU OK LED

For a description of the PSU OK LEDs, see the “Power-Supply Module LEDs” section on page 1-9.

Cisco IE 3010 Switch Hardware Installation Guide

3-2

78-19581-02

 

 

Chapter 3 Power Supply Installation

Power-SupplyModule Installation

Power-SupplyModule Installation

Installation Guidelines, page 3-3

Installing a Power-Supply Module, page 3-4

Wiring the Power Source, page 3-7

Removing the Power-Supply Module, page 3-12

Installation Guidelines

Observe these guidelines when removing or installing a power-supplymodule:

A power-supplymodule that is only partially connected to the switch disrupts the system operation.

Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place.

Statement 1029

Note You can order the blank cover (part numberRPS-CG-COVER=).

Warning Do not reach into a vacant slot while installing or removing a module. Exposed circuitry is an energy hazard.Statement 206

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Warning Avoid using or servicing any equipment that has outdoor connections during an electrical storm. There may be a risk of electric shock from lightning.Statement 1088

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

3-3

 

 

 

Chapter 3 Power Supply Installation

Power-SupplyModule Installation

Installing a Power-SupplyModule

This procedure is for installing a power-supplymodule in the PSU1 or PSU2 slot.

Warning The covers are an integral part of the safety design of the product. Do not operate the unit without the covers installed.Statement 1077

Warning This unit might have more than one power supply connection. All connections must be removed tode-energizethe unit.Statement 1028

Caution Equipment installation must comply with local and national electrical codes.

Equipment That You Need

Ratcheting torque flathead screwdriver that exerts up to 15-inchpound(in-lb)of torque

Ring, spade, or flanged spade terminal (terminals should be insulated)

Ring terminal (such as Tyco part number 2-34158-1for1614AWG or2-34852-1for1210AWG wire)

Spade terminal (such as Tyco part number 54367-2for1614AWG wire)

Flanged spade terminal (such as Tyco part number 2-324165-1for1614AWG wire or1-324581-1for1210AWG wire)

Note ForIP-30compliance:

-Use the 16-14AWG wire and appropriate terminals for the AC orhigh-voltageDC power supply

-Use the12-10AWG wire and appropriate terminals for thelow-voltageDC power supply

Crimping tool (such as Thomas & Bett part number WT2000, ERG-2001)

6-gaugecopper ground wire (such as Belden part number 9906)

12-AWGwire (minimum) for thelow-voltagepower-supplymodule and16-AWG(minimum) wire for thehigh-voltagepower-supplymodule

For power source connections, use wires rated for at least 194°F (90°C).

ULand CSA-ratedstyle 1007 or 1569twisted-paircopper wire (such as Belden part number 9318)

Wire-strippingtools for stripping6-,10-,12-,14-,and16-gaugewires.

Number-2Phillips screwdriver

Flat-bladescrewdriver

Grounding the Switch

Follow the grounding procedures at your site and observe these warnings:

Cisco IE 3010 Switch Hardware Installation Guide

3-4

78-19581-02

 

 

Chapter 3 Power Supply Installation

Power-SupplyModule Installation

Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available.Statement 1024

Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last.Statement 1046

Caution Follow the grounding procedure instructions, and use aUL-listedlug (included with the switch) fornumber-6AWG wire and10-32ground-lugscrews.

Note You can use the grounding lug to attach a wrist strap for ESD protection during servicing.

Follow these steps to install a dual-holelug on the switch. Be sure to follow any grounding requirements at your site.

Step 1 Use a Phillips screwdriver or a ratcheting torque screwdriver with a Phillips head to remove the ground screw from the cable side of the switch. You need the screw in Step 4.

Step 2 Strip the6-gaugeground wire to 0.5 inch (12.7 mm) ± 0.02 inch (0.5 mm). SeeFigure 3-3.Stripping more than the recommended amount of wire can leave exposed wire from the connector.

Figure 3-3Stripping the Ground Wire

0.5 in. (12.7 mm) ± 0.02 in. (0.5 mm)

Wire lead

Insulation

60528

Step 3 Insert the ground wire into the terminal lug, and crimp the terminal to the wire. (seeFigure 3-4).

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

3-5

 

 

 

Chapter 3 Power Supply Installation

Power-SupplyModule Installation

Figure 3-4Crimping the Terminal Lug

280938

Step 4 Slide the ground screw from Step 1 through the terminal lug. Insert the ground screws into the opening on the cable side.

Figure 3-5Attaching the Terminal Lug

 

 

208335

 

 

 

 

 

 

1

Dual-holeterminal lug

 

 

 

 

Step 5

Use a ratcheting torque screwdriver to tighten the ground screws to 30 in-lb(± 2in-lb).

Step 6

Attach the other end of the ground wire to a grounded bare metal surface, such as a ground bus or a

 

grounded bare rack.

 

 

 

 

Installing the Power-SupplyModule in the Switch

Step 1 We recommend that power be off at the AC or DC circuits. Locate the circuit breakers, turn them OFF, and tape them in the OFF position.

Note If the power is not off at the AC or DC circuit breaker, do not touch thepower-inputterminal.

Step 2 Use a Phillips screwdriver to loosen the two captive screws of the blankpower-supplymodule and gently pull it out. SeeFigure 3-6 andFigure 3-7.

Cisco IE 3010 Switch Hardware Installation Guide

3-6

78-19581-02

 

 

Chapter 3 Power Supply Installation

Power-SupplyModule Installation

Figure 3-6Loosen the Screws on the Power Supply Blank

Cisco IE

3010

Sw

 

 

itchSeries

208382

Figure 3-7Remove the Power Supply Blank

Cisco Connected

Sw itch rid

208383

Step 3 Insert thepower-supplymodule into the slot, and gently push it in. SeeFigure 3-8.Thepower-supplymodule should be flush with the switch.

Figure 3-8Insert thePower-SupplyModule

208377

Step 4 Use a ratcheting torque screwdriver to torque each screw to8–10in-lb.

Wiring the Power Source

Before you wire the power source, review the warnings in this section:

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

3-7

 

 

 

Chapter 3 Power Supply Installation

Power-SupplyModule Installation

Warning This product relies on the building’s installation forshort-circuit(overcurrent) protection. Ensure that the protective device is rated not greater than:

AC: 5 A, DC: 15 A Statement 1005

Warning A readily accessibletwo-poleddisconnect device must be incorporated in the fixed wiring.

Statement 1022

Warning Only trained and qualified personnel should be allowed to install or replace this equipment.

Statement 1030

Warning Hazardous voltage or energy may be present on power terminals. Always replace cover when terminals are not in service. Be sure uninsulated conductors are not accessible when cover is in place.Statement 1086

Step 1 Locate the AC and DC circuit breakers, turn them OFF, and tape them in the OFF position.

Note Do not connect the switch to a power source that has an ON/OFF switch.

Step 2 Use a Phillips screwdriver to loosen the captive screw on thepower-inputterminal, and open the cover.

Figure 3-9Opening thePower-InputTerminal Cover

100-

 

240V~, 50-

 

60Hz, 2A

207426

The terminal screws labels are on the power-inputterminal cover. SeeFigure 3-10.

Cisco IE 3010 Switch Hardware Installation Guide

3-8

78-19581-02

 

 

Chapter 3 Power Supply Installation

Power-SupplyModule Installation

Figure 3-10

Power-InputTerminal

 

 

100-240V~,50-60Hz,2A

100-240V~,50-60Hz,2A

 

1

 

2

8

9

 

3

 

4

10

11

 

5

5

2A

5

2A

12

 

 

 

 

6

7

13

14

10A

 

 

10A

207241

1

Line connection for high-voltageAC (PSU1)

8

Line connection for high-voltageAC (for

 

 

 

PSU2)

 

 

 

 

2

Neutral connection for high-voltageAC

9

Neutral connection for high-voltageAC

 

(PSU1)

 

(PSU2)

 

 

 

 

3

Positive connection for high-voltageDC

10

Positive connection for high-voltageDC

 

(PSU1)

 

(PSU2)

 

 

 

 

4

Negative connection for high-voltageDC

11

Negative connection for high-voltageDC

 

(PSU1)

 

(PSU2)

 

 

 

 

5

PSU1 (power-supplymodule 1)

12

PSU2 (power-supplymodule 2)

 

 

 

 

6

Positive connection for low-voltageDC

13

Positive connection for low-voltageDC

 

(PSU1)

 

(PSU2)

 

 

 

 

7

Negative connection for low-voltageDC

14

Negative connection for low-voltageDC

 

(PSU1)

 

(PSU2)

 

 

 

 

Note Thepower-supplymodule 1 connection is labeled PSU1, and thepower-supplymodule 2 connection is labeled PSU2. Make sure that you connect the wires to the correct terminal screws.

Step 3 Usetwisted-paircopper wire (14to18-AWG)to connect from thepower-inputterminal to the power source.

Note Use12-AWG(minimum) for thelow-voltageDC power supply module. Use16-AWG(minimum) for thehigh-voltageAC or DC power supply module.

Step 4 Strip each of the two wires to 0.25 inch (6.3 mm) ± 0.02 inch (0.5 mm). Do not strip more than 0.27 inch (6.8 mm) of insulation from the wire. Stripping more than the recommended amount of wire can leave exposed wire from the connector after installation.

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

3-9

 

 

 

Chapter 3 Power Supply Installation

Power-SupplyModule Installation

Figure 3-11Stripping the Input Power Source Wire

0.25 in. (6.3 mm) ± 0.02 in. (0.5 mm)

60531

Step 5 Insert the wire into a spade terminal, and crimp it to the wire. You can also use a ring or flanged spade terminal as listed in the“Equipment That You Need” section on page 3-4.

Figure 3-12Crimping the Spade Terminal Lug

207427

Step 6 Loosen the terminal screw, and slide the terminal under the screw and washer. SeeFigure 3-14.

Note Use the appropriate terminal screws, depending on whether you are installing ahigh-voltage(AC or DC) or alow-voltage(DC) power supply.

Step 7 To connect the AC power:

a.Connect the line wire into the terminal screw labeled L and the neutral wire into the terminal screw labeledN.

b.Make sure that you cannot see any wire lead. Only wire with insulation should extend from the terminal screw.

Cisco IE 3010 Switch Hardware Installation Guide

3-10

78-19581-02

 

 

Chapter 3 Power Supply Installation

Power-SupplyModule Installation

Figure 3-13Connecting the Wires to theHigh-VoltageAC Power (PSU1)

co IE 3010

208381

To connect the DC power:

a.Connect the positive wire into the terminal screw labeled +, and the negative wire into the terminal screw labeled.

b.Make sure that you cannot see any wire lead. Only wire with insulation should extend from the terminal screw.

Note If you have alow-voltageDCpower-supplymodule, connect the wires to the terminals labeledLo. If you have ahigh-voltageDCpower-supplymodule, connect the wires to the terminals labeledHi.

Figure 3-14Connecting the Wires to theLow-VoltageDC Power (PSU2)

208380

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

3-11

 

 

 

Chapter 3 Power Supply Installation

Removing the Power-SupplyModule

Step 8 Torque the captive screws (above the wires) to 8.5in-lb(± 0.5in-lb).

Step 9 AC power

Connect the other end of the line wire (the one connected to L) to the line terminal on theAC-powersource, and connect the other end of the neutral wire (the one connected toN) to the neutral terminal on the AC power source.

DC power

Connect the other end of the positive wire (the one connected to +) to the positive terminal on theDC-powersource, and connect the other end of the negative wire (the one connected

to )to the negative terminal on the DC power source.

Step 10 Close thepower-inputterminal cover. Use a ratcheting torque screwdriver to torque the screw to6–8in-lb.

Step 11 Turn on the power at the AC or DC circuit, verify that thePSU1 or PSU2 LED on the switch andPSU OK LED on thepower-supplymodule are green.

Step 12 If you have two power supplies, repeat Step 1 through Step 11. See the switch software guide for information on how to configure the power supply settings.

Removing the Power-SupplyModule

The power-supplymodules arehot-swappable.By removing thepower-supplymodules, you can power off the switch without disconnecting the wiring from thepower-inputterminal.

Step 1 We recommend that power be OFF at the AC or DC circuits. Locate the circuit breakers, turn them OFF and tape them in the OFF position.

Note If the power is not off at the AC or DC circuit breaker, do not touch thepower-inputterminal.

Step 2 Verify that the PSU LED and PSU OK LED is blinking red or is off.

Step 3 Use a Phillips screwdriver to loosen the captive screws that secure thepower-supplymodule to the switch. SeeFigure 3-15.

Warning Hot surface. Statement 1079

Figure 3-15Removing the Screws

Cisco IE

3010

Sw

 

 

itchSeries

208384

 

Cisco IE 3010 Switch Hardware Installation Guide

3-12

78-19581-02

Chapter 3 Power Supply Installation

Removing the Power-SupplyModule

Step 4 Remove thepower-supplymodule from the power slot. Thepower-supplymodule might be hot. SeeFigure 3-16.

Step 5 Install a newpower-supplymodule or a blank cover.

Figure 3-16Removing thePower-SupplyModule

Cisco IE

3010

Sw

 

 

itchSeries

208385

Caution To prevent exposure to hazardous voltages and to contain electromagnetic interference (EMI), either apower-supplymodule or a blank cover must be in eachpower-supplymodule slot at all times. You can order the blank cover (part numberRPS-CG-COVER=).

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

3-13

 

 

 

Chapter 3 Power Supply Installation

Removing the Power-SupplyModule

Cisco IE 3010 Switch Hardware Installation Guide

3-14

78-19581-02

 

 

C H A P T E R 4

Troubleshooting

Diagnosing Problems, page 4-1

Resetting the Switch to the Factory Default Settings, page 4-5

Finding the Switch Serial Number, page 4-5

Diagnosing Problems

The switch LEDs provide troubleshooting information about the switch. They show POST failures, port-connectivityproblems, and overall switch performance. You can also get statistics from Device Manager, the CLI, or an SNMP workstation. See the software configuration guide, the switch command reference guide on Cisco.com, or the documentation that came with your SNMP application for details.

Switch POST Results

See the “Verifying Switch Operation” section on page 2-3 for information on POST.

Note POST failures are usually fatal. Contact your Cisco technical support representative if your switch does not pass POST.

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

4-1

 

 

 

Chapter 4 Troubleshooting

Diagnosing Problems

Switch LEDs

Look at the port LEDs information when troubleshooting the switch. See the “LEDs” section on page 1-8 for a description of the LED colors and their meanings.

Switch Connections

Bad or Damaged Cable

Always examine the cable for marginal damage or failure. A cable might be just good enough to connect at the physical layer, but it could corrupt packets as a result of subtle damage to the wiring or connectors. You can identify this problem because the port has many packet errors or it constantly flaps (loses and regains link).

Exchange the copper or fiber-opticcable with a known good cable.

Look for broken or missing pins on cable connectors.

Rule out any bad patch panel connections or media convertors between the source and the destination. If possible, bypass the patch panel, or eliminate media convertors (fiber-optic-to-copper).

Try the cable in another port to see if the problem follows the cable.

Ethernet and Fiber-OpticCables

Make sure that you have the correct cable:

For Ethernet, use Category 3 copper cable for 10 Mb/s UTP connections. Use either Category 5, Category 5e, or Category 6 UTP for 10/100 or 10/100/1000 Mb/s connections.

Verify that you have the correct fiber-opticcable for the distance and port type. Make sure that the connected device ports match and use the same type encoding, optical frequency, and fiber type.

Determine if a copper crossover cable was used when a straight-throughwas required or the reverse. Enableauto-MDIXon the switch, or replace the cable. SeeTable 2-1 for recommended Ethernet cables.

Link Status

Verify that both sides have link. A broken wire or a shutdown port can cause one side to show link even though the other side does not have link.

A port LED that is on does not guarantee that the cable is functional. It might have encountered physical stress, causing it to function at a marginal level. If the port LED does not turn on:

Connect the cable from the switch to a known good device.

Make sure that both ends of the cable are connected to the correct ports.

Verify that both devices have power.

Verify that you are using the correct cable type. See Appendix B, “Connector and Cable Specifications” for information.

Look for loose connections. Sometimes a cable appears to be seated but is not. Disconnect the cable, and then reconnect it.

Cisco IE 3010 Switch Hardware Installation Guide

4-2

78-19581-02

 

 

Chapter 4 Troubleshooting

Diagnosing Problems

10/100 and 10/100/1000 Port Connections

A port appears to malfunction:

Verify the status of all ports. See Table 1-8 on page 1-10 for descriptions of the LEDs and their meanings.

Use the show interfaces privileged EXEC command to see if the port iserror-disabled,disabled, or shut down.Re-enablethe port if necessary.

Verify the cable type. See Appendix B, “Connector and Cable Specifications.”

10/100 PoE Port Connections

A powered device connected to a PoE port does not receive power:

Verify the status of all the ports. See Table 1-8 for descriptions of the LEDs and their meanings.

Use the show interfaces privileged EXEC command to see if the port iserror-disabled,disabled, or shutdown.Re-enablethe port if necessary.

Verify the cable type. Many legacy powered devices, including older Cisco IP phones and access points that do not fully support IEEE 802.3af might not support PoE when connected to the switch by a crossover cable. Replace the crossover cable with a straight-throughcable.

Caution Noncompliant cabling or powered devices can cause a PoE port fault. Use only compliant cabling to connect Cisco prestandard IP Phones, and wireless access points, or IEEE802.3af-compliantdevices.

SFP Module

Use only Cisco SFP modules. Each Cisco module has an internal serial EEPROM that is encoded with security information. This encoding verifies that the module meets the requirements for the switch.

Inspect the SFP module. Exchange the suspect module with a known good module.

Verify that the module is supported on this platform. (The switch release notes on Cisco.com list the SFP modules that the switch supports.)

Use the show interfaces privileged EXEC command to see if the port or module iserror-disabled,disabled, or shutdown.Re-enablethe port if needed.

Make sure that all fiber-opticconnections are clean and securely connected.

Interface Settings

Verify that the interface is not disabled or powered off. If an interface is manually shut down on either side of the link, it does not come up until you re-enablethe interface. Use theshow interfaces privileged EXEC command to see if the interface iserror-disabled,disabled, or shut down on either side of the connection. If needed,re-enablethe interface.

Ping End Device

Ping from the directly connected switch first, and then work your way back port by port, interface by interface, trunk by trunk, until you find the source of the connectivity issue. Make sure that each switch can identify the end device MAC address in its Content-AddressableMemory (CAM) table.

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

4-3

 

 

 

Chapter 4 Troubleshooting

Diagnosing Problems

Spanning Tree Loops

STP loops can cause serious performance issues that look like port or interface problems.

A unidirectional link can cause loops. It occurs when the traffic sent by the switch is received by the neighbor, but the traffic from the neighbor is not received by the switch. A broken cable, other cabling problems, or a port issue could cause this one-waycommunication.

You can enable UniDirectional Link Detection (UDLD) on the switch to help identify unidirectional link problems. For information about enabling UDLD on the switch, see the “Understanding UDLD” section in the switch software configuration guide on Cisco.com.

Switch Performance

Speed, Duplex, and Autonegotiation

Port statistics that show a large amount of alignment errors, frame check sequence (FCS), or late-collisionserrors, might mean a speed or duplex mismatch.

A common issue occurs when duplex and speed settings are mismatched between two switches, between a switch and a router, or between the switch and a workstation or server. Mismatches can happen when manually setting the speed and duplex or from autonegotiation issues between the two devices.

To maximize switch performance and to ensure a link, follow one of these guidelines when changing the duplex or the speed settings.

Let both ports autonegotiate both speed and duplex.

Manually set the speed and duplex parameters for the interfaces on both ends of the connection.

If a remote device does not autonegotiate, use the same duplex settings on the two ports. The speed parameter adjusts itself even if the connected port does not autonegotiate.

Autonegotiation and Network Interface Cards

Problems sometimes occur between the switch and third-partynetwork interface cards (NICs). By default, the switch ports and interfaces autonegotiate. Laptops or other devices are commonly set to autonegotiate, yet sometimes issues occur.

To troubleshoot autonegotiation problems, try manually setting both sides of the connection. If this does not solve the problem, there could be a problem with the firmware or software on the NIC. You can resolve this by upgrading the NIC driver to the latest version.

Cabling Distance

If the port statistics show excessive FCS, late-collision,or alignment errors, verify that the cable distance from the switch to the connected device meets the recommended guidelines. See the“Cables and Adapters” section on page B-4.

Cisco IE 3010 Switch Hardware Installation Guide

4-4

78-19581-02

 

 

Chapter 4 Troubleshooting

Resetting the Switch to the Factory Default Settings

Resetting the Switch to the Factory Default Settings

Follow these steps to return your switch to the factory default settings.

Note Resetting the switch deletes the configuration and reboots the switch.

To reset the switch:

1.At the switch prompt, enter enable, and pressReturn orEnter.

2.At the Privileged EXEC prompt, switch#, entersetup and pressReturn orEnter.

The switch displays the prompt to run the initial configuration dialog. See Appendix C, “Configuring the Switch with the CLI Setup Program.”

Finding the Switch Serial Number

If you contact Cisco Technical Assistance, you need to know the switch serial number. Figure 4-1 andFigure 4-2 show the serial number locations. You can also use theshow version privileged EXEC command to see the switch serial number.

Figure 4-1Serial Number Location for CiscoIE-3010-24TCandIE-3010-16S-8PCSwitches

SN: XXXNNNNXXXX

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

4-5

 

 

 

Chapter 4 Troubleshooting

Finding the Switch Serial Number

Figure 4-2Serial Number Location for thePower-SupplyModules

SN: XXXNNNNXXXX

207452

Cisco IE 3010 Switch Hardware Installation Guide

4-6

78-19581-02

 

 

A P P E N D I X A

Technical Specifications

Switch Specifications

Power-Supply Module Specifications

Alarm Ratings

Switch Specifications

Table A-1

Environmental and Physical Specifications

 

 

Environmental Ranges

 

 

 

Operating temperature

–40to 140°F(–40to 60°C)1

Storage temperature

–40to 185°F(–40to 85°C)

 

 

Relative humidity

5 to 95% (noncondensing)

 

 

Operating altitude

Up to 10,000 ft (3049 m)

 

 

 

Storage altitude

 

Up to 15,000 ft (4570 m)

 

 

Thermal spacing

1.75 in. (4.4 cm)

 

 

 

Operating shock

 

30 g at 11 ms

 

 

Physical Specifications

 

 

 

 

Weight

 

 

Cisco IE-3010-24TC

9.1 lb (4.1 kg) (no power-supplymodule)

Cisco IE-3010-16S-8PC

10 lb (4.5 kg) (no power-supplymodule)

 

 

Dimensions (H x W x D)

 

Cisco IE-3010-24TC

1.75 x 17.5 x 14.0 in. (4.45 x 44.5 x 35.6 cm)

Cisco IE-3010-16S-8PC

1.75 x 17.5 x 14.0 in. (4.45 x 44.5 x 35.6 cm)

 

 

 

1.The maximum operating temperature of the switch varies depending on the type of SFP module that you use. See Table 1-2 on page 1-5 for information on the supported temperature ranges for the SFPs.

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

A-1

 

Appendix A Technical Specifications

Switch Specifications

Table A-2Technical Specifications for the Cisco IE3010-16S-8PCSwitch

Power Requirements

Nominal input voltage

PWR-RGD-AC-DC/IA:

 

100 to 240 VAC, 50 to 60 Hz

 

100 to 250 VDC

 

PWR-RGD-LOW-DC/IA:

 

24 to 60 VDC

 

 

Absolute maximum (short term) input voltage

PWR-RGD-AC-DC/IA:

 

85 to 265 VAC, 47 to 63 Hz

 

88 to 300 VDC

 

PWR-RGD-LOW-DC/IA:

 

18 to 75 VDC

 

 

Power consumption with one PWR-RGD-AC-DC/IA

AC: 147 BTUs per hour

power-supplymodule

43.2 W

 

Power rating: 0.044 KVA@115 V

 

 

 

DC: 137 BTUs per hour

 

40.3 W

 

Power rating: 0.0403 KVA@125 VDC

 

 

Power consumption with one PWR-RGD-AC-DC/IA

AC: 376 BTUs per hour

power-supplymodule (with PoE on 4 ports)

110.1 W

 

Power rating 0.11 KVA@115 V

 

 

 

DC: 375 BTUs per hour

 

109.8 W

 

Power rating: 0.109 KVA@125 VDC

 

 

Power consumption with two PWR-RGD-AC-DC/IA

AC: 166 BTUs per hour

power-supplymodules

48.8 W

 

Power rating: 0.051 KVA@115 V

 

 

 

DC: 167 BTUs per hour

 

48.9 W

 

Power rating: 0.0489 KVA@125 VDC

 

 

Power consumption with two PWR-RGD-AC-DC/IA

AC: 628 BTUs per hour

power-supplymodules (with PoE on 8 ports)

184.1 W

 

Power rating: 0.185 KVA@115 V

 

 

 

DC: 622 BTUs per hour

 

182.2 W

 

Power rating: 0.182 KVA@125 VDC

 

 

Power consumption with one

DC: 116 BTUs per hour

PWR-RGD-LOW-DC/IApower-supplymodule

34.2 W

 

Power rating: 0.034 KVA@24 VDC

 

 

Power consumption with one

DC: 363 BTUs per hour

PWR-RGD-LOW-DC/IApower-supplymodule

106 W

(with PoE on 4 ports)

Power rating: 0.106 KVA@24 VDC

 

 

Cisco IE 3010 Switch Hardware Installation Guide

 

A-2

78-19581-02

 

 

 

Appendix A Technical Specifications

Switch Specifications

Table A-2Technical Specifications for the Cisco IE3010-16S-8PCSwitch (continued)

Power consumption with two

 

DC: 127 BTUs per hour

PWR-RGD-LOW-DC/IApower-supplymodules

 

37.1 W

 

 

 

Power rating: 0.037 KVA@24 VDC

 

 

 

 

Power consumption with two

 

DC: 622 BTUs per hour

PWR-RGD-LOW-DC/IApower-supplymodules

 

181.9 W

(with PoE on 8 ports)

 

Power rating: 0.182 KVA@24 VDC

 

 

 

 

 

Table A-3

Technical Specifications for the Cisco IE-3010-24TCSwitch

 

 

 

 

Power Requirements

 

 

 

 

 

 

Nominal input voltage

PWR-RGD-AC-DC/IA:

 

 

100 to 240 VAC, 50 to 60 Hz

 

 

100 to 250 VDC

 

 

PWR-RGD-LOW-DC/IA:

 

 

24 to 60 VDC

 

 

 

Absolute maximum (short term) input voltage

PWR-RGD-AC-DC/IA:

 

 

85 to 265 VAC, 47 to 63 Hz

 

 

88 to 300 VDC

 

 

PWR-RGD-LOW-DC/IA:

 

 

18 to 75 VDC

 

 

 

Power consumption with one

AC: 102 BTUs per hour

PWR-RGD-AC-DC/IApower-supplymodule

29.8 W

 

 

Power rating: 0.031 KVA@115 V

 

 

 

 

 

 

DC: 98 BTUs per hour

 

 

28.6 W

 

 

Power rating: 0.0286 KVA@125 VDC

 

 

 

Power consumption with two

AC: 121 BTUs per hour

PWR-RGD-AC-DC/IApower-supplymodules

35.5 W

 

 

Power rating: 0.0367 KVA@115 V

 

 

 

 

 

 

DC: 117 BTUs per hour

 

 

34.4 W

 

 

Power rating: 0.0344 KVA@ 125 VDC

 

 

 

Power consumption with one

DC: 92 BTUs per hour

PWR-RGD-LOW-DC/IApower-supplymodule

26.8 W

 

 

Power rating: 0.027 KVA@ 24 VDC

 

 

 

Power consumption with two

DC: 105 BTUs per hour

PWR-RGD-LOW-DC/IApower-supplymodules

30.7 W

 

 

Power rating: 0.030 KVA@ 24 VDC

 

 

 

 

 

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

A-3

 

Appendix A Technical Specifications

Power-SupplyModule Specifications

Power-SupplyModule Specifications

Table A-4

Environmental and Physical Specifications for the ACand DC-Power-Supply

 

Modules

 

 

 

 

 

 

 

 

 

 

 

 

 

Environmental Ranges

 

 

 

 

 

 

 

 

 

 

 

 

 

Operating temperature

–40to 140°F(–40to 60°C)

 

 

 

 

 

 

 

Storage temperature

–49to 185°F(–45to 85°C)

 

 

 

 

 

 

 

Relative humidity

5 to 95% (noncondensing)

 

 

 

 

 

 

 

 

Altitude

 

Up to 10,000 ft (3049 m)

 

 

 

 

 

 

 

Physical Specifications

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Weight

 

 

 

 

 

 

 

PWR-RGD-AC-DC/IA

2.55 lb (1.15 kg)

PWR-RGD-LOW-DC/IA

2.5 lb (1.13 kg)

 

 

 

 

 

 

 

Dimensions (H x W x D)

 

 

 

 

 

 

PWR-RGD-AC-DC/IAand

1.58 x 7 x 5 in. (4 x 17.8 x 12.7 cm)

(without mounting flanges)

PWR-RGD-LOW-DC/IA

1.58 x 8.15 x 5 in. (4 x 20.7 x 12.7 cm)

 

 

 

 

(with mounting flanges)

 

 

 

 

 

 

 

 

Table A-5

Technical Specifications for the PWR-RGD-AC-DC/IAPower-SupplyModule

 

 

 

 

 

 

 

Power Specifications

 

 

 

 

 

 

 

 

 

 

 

 

Maximum output power

 

 

150 W

 

 

 

 

 

 

Nominal input voltage

 

 

100 to 240 VAC, 50 to 60 Hz

 

 

 

 

100 to 250 VDC

 

 

 

 

 

 

Absolute maximum (short term) input voltage

 

 

85 to 265 VAC, 47 to 63 Hz

 

 

 

 

88 to 300 VDC

 

 

 

 

 

 

 

Input current

 

 

 

AC: 2.2 to 0.7 A, 85 to 265 VAC

 

 

 

 

DC: 2.5 to 0.6 A, 88 to 300 VDC

 

 

 

 

 

 

Total input BTU

 

 

AC: 638 BTUs per hour

 

 

 

 

DC: 750 BTUs per hour

 

 

 

 

 

 

Table A-6

Technical Specifications for the PWR-RGD-LOW-DC/IAPower-SupplyModule

 

 

 

 

 

 

 

Power Specifications

 

 

 

 

 

 

 

 

 

 

Maximum output power

 

150 W

 

 

 

 

Nominal input voltage

 

24 to 60 VDC

 

 

 

 

Absolute maximum (short term) input voltage

 

18 to 75 VDC

 

 

 

 

 

Input current

 

 

12 to 2.5 A, 18 to 75 VDC

 

 

 

 

Total input BTU

 

737 BTUs per hour

 

 

 

 

 

 

 

 

Cisco IE 3010 Switch Hardware Installation Guide

 

A-4

78-19581-02

 

 

 

Appendix A Technical Specifications

Alarm Ratings

Alarm Ratings

Table A-7

Alarm Input and Output Ratings

 

 

 

 

Alarm Ratings

 

 

 

 

Alarm input electrical specification

8 V @ 1mA

 

 

Alarm output electrical specification

30 V @ 1A

 

 

Note The alarm output does not support AC

 

 

voltage because the RJ-45connector pin

 

 

spacing is too small.

 

 

 

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

A-5

 

Appendix A Technical Specifications

Alarm Ratings

Cisco IE 3010 Switch Hardware Installation Guide

 

A-6

78-19581-02

 

 

 

A P P E N D I X B

Connector and Cable Specifications

Connector Specifications, page B-1

Cables and Adapters, page B-4

Connector Specifications

10/100, page B-1

SFP Module Connectors, page B-2

Dual-Purpose Ports, page B-3

Alarm Port, page B-3

10/100

The 10/100 Ethernet ports use standard RJ-45connectors and Ethernet pinouts with internal crossovers. These ports have the send (TD) and receive (RD) signals internally crossed so that atwisted-pairstraight-throughcable and adapter can be attached.

Figure B-110/100 Port Pinouts

Pin Label

1RD+

2RD-

3TD+

4NC

5NC

6TD-

7NC

8NC

1 2 3 4 5 6 7 8

H5318

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

B-1

 

Appendix B Connector and Cable Specifications

Connector Specifications

When connecting 10/100 ports to devices such as servers, workstations, and routers, you can use a two or four twisted-pairstraight-throughcable wired for10BASE-Tand100BASE-TX.Figure B-5 shows the twotwisted-pairstraight-throughcable schematics.Figure B-7 shows the fourtwisted-pairstraight-throughcable schematics.

When connecting the ports to other devices, such as switches or repeaters, you can use a two or four twisted-paircrossover cable.Figure B-6 shows the twotwisted-paircrossover cable schematics.Figure B-8 shows the fourtwisted-paircrossover cable schematics.

If auto-MDIXis disabled, use astraight-throughcable to connect ports when only one port is labeled with an X. Use a crossover cable to connect ports when both ports are labeled with an X or when both ports are not labeled with an X.

You can use Category 3, 4, or 5 cabling when connecting to 10BASE-T-compatibledevices. You must use Category 5 (or higher) cabling when connecting to100BASE-TX-compatibledevices.

Note You can use themdix auto interface configuration command in the CLI to enable the automaticmedium-dependentinterface crossover(auto-MDIX)feature. When theauto-MDIXfeature is enabled, the switch detects the required cable type for copper Ethernet connections and configures the interfaces accordingly. Therefore, you can use either a crossover or astraight-throughcable for connections to a copper 10/100, 10/100/1000, or1000BASE-TSFP module port on the switch, regardless of the type of device on the other end of the connection.

SFP Module Connectors

Figure B-2Fiber-OpticSFP Module LC Connector

58476

Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments.Statement 1051

Cisco IE 3010 Switch Hardware Installation Guide

 

B-2

78-19581-02

 

 

 

Appendix B Connector and Cable Specifications

Connector Specifications

Dual-PurposePorts

The 10/100/1000 Ethernet ports on the dual-purposeports useRJ-45connectors.

Figure B-310/100/1000 Port Pinouts

Pin Label

1TP0+

2TP0-

3TP1+

4TP2+

5TP2-

6TP1-

7TP3+

8TP3-

1 2 3 4 5 6 7 8

60915

Alarm Port

The alarm port uses an RJ-45connector. See the“Alarm Ports” section on page 1-6 for more information. For information on alarm ratings, see the“Alarm Ratings” section on page A-5.

Figure B-4Alarm Port Pinouts

Pin

Alarm connection

1Alarm 1 input

2Alarm 2 input

3Normally closed

4Alarm 3 input

5Alarm 4 input

6Normally open

7Alarm output common

8Alarm input common

1 2 3 4 5 6 7 8

207434

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

B-3

 

Appendix B Connector and Cable Specifications

Cables and Adapters

Cables and Adapters

SFP Module Cables, page B-4

Cable Pinouts, page B-6

Console Port Adapter Pinouts, page B-7

SFP Module Cables

Each port must match the wave-lengthspecifications on each end of the cable, and for reliable communications, the cable must not exceed the allowable length. Copper1000BASE-TSFP transceivers use standard fourtwisted-pair,Category 5 (or greater) cable at lengths up to 328 feet (100 meters).

Note The maximum operating temperature of the switch varies depending on the type of SFP module that you use. SeeTable 1-2 on page 1-5 for information on the supported temperature ranges.

Table B-1

Fiber-OpticSFP Module Port Cabling Specifications

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Core

Modal

 

 

 

 

 

 

 

Wavelength

 

Size/Cladding

Bandwidth

 

 

 

Type of SFP Module

(nanometers)

Fiber Type

Size (micron)

(MHz/km)1

Cable Distance

 

Industrial and Rugged SFPs

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1000BASE-SX

 

850

MMF

62.5/125

160

722 feet (220 m)

 

(GLC-SX-MM-RGD)

 

 

62.5/125

200

902 feet (275 m)

 

 

 

 

 

 

 

50/125

400

1640 feet (500 m)

 

 

 

 

 

 

 

50/125

500

1804 feet (550 m)

 

 

 

 

 

 

 

 

1000BASE-LX/LH

1310

SMF

G.6522

32,810 feet (10 km)

 

(GLC-LX-MM-RGD)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

100BASE-LX

 

1310

SMF

G.6522

32,810 feet (10 km)

 

(GLC-FE-100LX-RGD)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

100BASE-FX

 

1310

MMF

50/125

500

6,562 feet (2 km)

 

(GLC-FE-100FX-RGD)

 

 

62.5/125

500

6,562 feet (2 km)

 

 

 

 

 

 

 

 

 

1000BASE-ZX

 

1550

SMF

G.6522

43.4 to 62 miles

 

(GLC-ZX-SM-RGD)

 

 

 

 

(70 to 100 km)2

 

Commercial SFPs

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1000BASE-BX10-D

1490 TX

SMF

G.6523

32,810 feet (10 km)

 

(GLC-BX-D)

 

1310 RX

 

 

 

 

 

 

 

 

 

 

 

 

 

 

100BASE-LX

 

1310

SMF

G.6522

32,810 feet (10 km)

 

(GLC-FE-100LX)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

100BASE-BX

 

1310 TX

SMF

G.6522

32,810 feet (10 km)

 

(GLC-FE-100BX-D

1550 RX

 

 

 

 

 

 

GLC-FE-100BX-U)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

100BASE-FX

 

1310

MMF

50/125

500

6,562 feet (2 km)

 

(GLC-FE-100FX)

 

 

62.5/125

500

6,562 feet (2 km)

 

 

 

 

 

 

 

 

 

 

 

 

 

Cisco IE 3010 Switch Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B-4

 

 

 

 

 

 

 

78-19581-02

 

 

 

 

 

 

 

 

 

 

Appendix B Connector and Cable Specifications

Cables and Adapters

Table B-1

Fiber-OpticSFP Module Port Cabling Specifications (continued)

 

 

 

 

 

 

 

 

 

 

 

 

 

Core

Modal

 

 

 

Wavelength

 

Size/Cladding

Bandwidth

 

Type of SFP Module

(nanometers)

Fiber Type

Size (micron)

(MHz/km)1

Cable Distance

100BASE-EX

 

1310

SMF

G.6522

131,240 feet (40 km)

(GLC-FE-100EX)

 

 

 

 

 

 

 

 

 

 

 

 

100BASE-ZX

 

1550

SMF

G.652

262,480 feet (80 km)

(GLC-FE-100ZX)

 

 

 

 

 

 

 

 

 

 

 

 

CWDM

 

1470, 1490, 1510, 1530, 1550,

SMF

G.6522

62 miles (100 km)

 

 

1570, 1590, 1610

 

 

 

 

 

 

 

 

 

 

Extended temperature SFPs

 

 

 

 

 

 

 

 

 

 

100BASE LX/LH

1300

MMF or

62.2

500

1804 feet (550 m)

(SFP-GE-L)

 

 

SMF

50

400

1804 feet (550 m)

 

 

 

 

50

500

1804 feet (550 m)

 

 

 

 

9/10

6.2 miles (10 km)

 

 

 

 

 

 

 

100BASE SX

 

850

MMF

62.5

160

722 feet (220 m)

(SFP-GE-S)

 

 

 

62.5

200

902 feet (275 m)

 

 

 

 

50.0

400

1640 feet (500 m)

 

 

 

 

50.0

500

1804 feet (550 m)

 

 

 

 

 

 

 

100BASE ZX

 

1550

SMF

9/10

43.5 miles (70 km)

(SFP-GE-Z)

 

 

SMF

8

 

62.1 miles (100 km)

 

 

 

 

 

 

 

100BASE EX

 

1310

SMF

G.6522

24.9 miles (40 km)

(GLC-EX-SMD)

 

 

 

 

 

 

 

 

 

 

 

 

1.Modal bandwidth applies only to multimode fiber.

2.1000BASE-ZXSFP modules can send data up to 62 miles (100 km) by usingdispersion-shiftedSMF orlow-attenuationSMF; the distance depends on the fiber quality, the number of splices, and the connectors.

3.A mode-fielddiameter/cladding diameter = 9 micrometers/125 micrometers.

Note When thefiber-opticcable span is less than 15.43 miles (25 km), insert a5-decibel(dB) or10-dBinline optical attenuator between thefiber-opticcable plant and the receiving port on the1000BASE-ZXSFP module.

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

B-5

 

Appendix B Connector and Cable Specifications

Cables and Adapters

Cable Pinouts

Figure B-5

Switch

3 TD+

6 TD–

1 RD+

2 RD–

Figure B-6

Switch

3 TD+

6 TD–

1 RD+

2 RD–

Figure B-7

Switch

1 TP0+

2 TP0-

3 TP1+

6 TP1-

4 TP2+

5 TP2-

7 TP3+

8 TP3-

Figure B-8

Switch

1 TP0+

2 TP0-

3 TP1+

6 TP1-

4 TP2+

5 TP2-

7 TP3+

8 TP3-

Two Twisted-PairStraight-ThroughCable Schematic for 10/100 Ports

Router or PC

3 RD+6 RD–

1 TD+

H5578

2 TD–

 

Two Twisted-PairCrossover Cable Schematic for 10/100 Ports

Switch

3 TD+

6 TD–

1 RD+

H5579

2 RD–

 

Four Twisted-PairStraight-ThroughCable Schematic for1000BASE-TPorts

Router or PC

 

1

TP0+

 

2

TP0-

 

3

TP1+

 

6

TP1-

 

4

TP2+

 

5

TP2-

 

7

TP3+

65271

8

TP3-

 

Four Twisted-PairCrossover Cable Schematics for1000BASE-TPorts

 

Switch

 

1

TP0+

 

2

TP0-

 

3

TP1+

 

6

TP1-

 

4

TP2+

 

5

TP2-

 

7

TP3+

65274

8

TP3-

 

Cisco IE 3010 Switch Hardware Installation Guide

 

B-6

78-19581-02

 

 

 

Appendix B Connector and Cable Specifications

Cables and Adapters

To identify a crossover cable, hold the cable ends side-by-side,with the tab at the back. The wire connected to pin 1 on the left end should be the same color as the wire connected to pin 3 on the right end. The wire connected to pin 2 on the left end should be the same color as the wire connected to pin 6 on the right end.

Figure B-9Identifying a Crossover Cable

Pin 1

 

 

 

 

 

 

 

 

 

Pin 3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pin 2

 

 

 

 

 

 

 

 

 

Pin 6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

273807

Console Port Adapter Pinouts

The console port uses an 8-pinRJ-45connector, which is described inTable B-2 andTable B-3.If you did not order a console cable, you need to provide anRJ-45-to-DB-9adapter cable to connect the switch console port to a PC console port. You need to provide anRJ-45-to-DB-25female DTE adapter if you want to connect the switch console port to a terminal. You can order an adapter (part numberACS-DSBUASYN=).For console port and adapter pinout information, seeTable B-2 andTable B-3.

Table B-2 lists the pinouts for the console port, theRJ-45-to-DB-9adapter cable, and the console device.

Table B-2Console Port Signaling Using aDB-9Adapter

Switch Console

RJ-45-to-DB-9

Console

Port (DTE)

Terminal Adapter

Device

 

 

 

Signal

DB-9Pin

Signal

 

 

 

RTS

8

CTS

 

 

 

DTR

6

DSR

 

 

 

TxD

2

RxD

 

 

 

GND

5

GND

 

 

 

RxD

3

TxD

 

 

 

DSR

4

DTR

 

 

 

CTS

7

RTS

 

 

 

Table B-3 lists the pinouts for the switch console port,RJ-45-to-DB-25female DTE adapter, and the console device.

Note TheRJ-45-to-DB-25female DTE adapter is not supplied with the switch. You can order this adapter from Cisco (part numberACS-DSBUASYN=).

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

B-7

 

Appendix B Connector and Cable Specifications

Cables and Adapters

Table B-3Console Port Signaling Using aDB-25Adapter

Switch

 

 

Console

RJ-45-to-DB-25

Console

Port (DTE)

Adapter

Device

 

 

 

Signal

DB-25Pin

Signal

 

 

 

RTS

5

CTS

 

 

 

DTR

6

DSR

 

 

 

TxD

3

RxD

 

 

 

GND

7

GND

 

 

 

RxD

2

TxD

 

 

 

DSR

20

DTR

 

 

 

CTS

4

RTS

 

 

 

Cisco IE 3010 Switch Hardware Installation Guide

 

B-8

78-19581-02

 

 

 

A P P E N D I X C

Configuring the Switch with the CLI Setup

Program

This appendix provides a command-lineinterface (CLI) setup procedure for a standalone switch. To set up the switch by using Express Setup, see theCisco IE 3010 Switch Getting Started Guide. Before connecting the switch to a power source, review the safety warnings inChapter 2, “Switch Installation,” andChapter 3, “Power Supply Installation.”

Accessing the CLI Through the Console Port

You can enter Cisco IOS commands and parameters through the CLI. Use one of these options to access the CLI:

RJ-45 Console Port

USB Console Port

RJ-45Console Port

Step 1 Connect theRJ-45-to-DB-9adapter cable to the9-pinserial port on the PC. Connect the other end of the cable to the switch console port.

Step 2 Start theterminal-emulationprogram on the PC or the terminal. The program, frequently a PC application such as HyperTerminal or ProcommPlus, makes communication between the switch and your PC or terminal possible.

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

C-1

 

Appendix C Configuring the Switch with the CLI Setup Program

Accessing the CLI Through the Console Port

Figure C-1Connecting the Console Cable

1

2

1

208386

1

RJ-45console port

2

Console cable (RJ-45-to-DB-9adapter cable)

 

 

 

 

Step 3 Configure the baud rate and character format of the PC or terminal to match the console port characteristics:

9600 baud

8 data bits

1 stop bit

No parity

None (flow control)

Step 4 Connect power to the switch as described inChapter 3, “Power Supply Installation.”

Step 5 The PC or terminal displays the bootloader sequence. PressEnter to display the setup prompt. Follow the steps in the“Completing the Setup Program” section on page C-7.

Cisco IE 3010 Switch Hardware Installation Guide

 

C-2

78-19581-02

 

 

 

Appendix C Configuring the Switch with the CLI Setup Program

Accessing the CLI Through the Console Port

USB Console Port

Step 1 If you are connecting the switch USB console port to aWindows-basedPC for the first time, install a USB driver. SeeFigure C-2.

“Installing the Cisco Microsoft Windows XP USB Driver” section on page C-4

“Installing the Cisco Microsoft Windows 2000 USB Driver” section on page C-4

“Installing the Cisco Microsoft Windows Vista USB Driver” section on page C-5

Figure C-2Connecting the USB Console Cable

1

Cisco IE 3010

2

1

 

2

3

1

USB console port

3

USB port on the PC

 

 

 

 

2

USB cable

 

 

 

 

 

 

208379

Step 2 Connect an USB cable to the PC USB port. Connect the other end of the cable to the switchmini-B(5-pin-connector)USB console port. SeeFigure C-2.

Step 3 To identify the COM port assigned to the USB console port: ChooseStart >Control Panel >Systems

Click the Hardware tab and chooseDevice Manager. Expand thePorts section. The assigned COM port appears in parenthesis at the end of the line with this entry: Cisco USB System Management Console.

Step 4 Start theterminal-emulationprogram on the PC or the terminal. The program, frequently a PC application such as HyperTerminal or ProcommPlus, makes communication possible between the switch and your PC or terminal.

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

C-3

 

Appendix C Configuring the Switch with the CLI Setup Program

Accessing the CLI Through the Console Port

Step 5 Configure the COM port.

Step 6 Configure the baud rate and character format of the PC or terminal to match the console port characteristics:

9600 baud

8 data bits

1 stop bit

No parity

None (flow control)

Step 7 Connect power to the switch as described inChapter 3, “Power Supply Installation.”

Step 8 The PC or terminal displays the bootloader sequence. PressEnter to display the setup prompt. Follow the steps in the“Completing the Setup Program” section on page C-7.

Installing the Cisco Microsoft Windows USB Device Drivers

Installing the Cisco Microsoft Windows XP USB Driver

Step 1 Obtain the file Cisco_usbconsole_driver.zip from Cisco.com, and unzip it.

Note You can download the driver file from the Cisco.com software download site.

Step 2 If using32-bitWindows XP,double-clickthe setup.exe file in the Windows_32 folder. If using64-bitWindows XP,double-clickthe setup(x64).exe file in the Windows_64 folder.

Step 3 The Cisco Virtual Com InstallShield Wizard begins.

Step 4 The Ready to Install the Program window appears. ClickInstall.

Step 5 The InstallShield Wizard Completed window appears. ClickFinish.

Step 6 Connect the USB cable to the PC and to the switch console port. The USB console port LED turns green, and the Found New Hardware Wizard appears. Follow the instructions to complete the driver installation.

Installing the Cisco Microsoft Windows 2000 USB Driver

 

 

 

Step 1

Obtain the file Cisco_usbconsole_driver.zip from Cisco.com, and unzip it.

 

 

 

 

 

 

 

 

 

 

 

Note

You can download the driver file from the Cisco.com software download site.

 

 

 

 

 

 

 

 

 

Step 2

Double-clickthe setup.exe file.

 

 

 

Step 3

The Cisco Virtual Com InstallShield Wizard begins. Click Next.

 

 

 

Step 4

The Ready to Install the Program window appears. Click Install.

 

 

 

Cisco IE 3010 Switch Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

C-4

 

 

 

 

78-19581-02

 

 

 

 

 

 

 

Appendix C Configuring the Switch with the CLI Setup Program

Accessing the CLI Through the Console Port

Step 5 The InstallShield Wizard Completed window appears. ClickFinish.

Step 6 Connect the USB cable to the PC and to the switch console port. The USB console port LED turns green, and the Found New Hardware Wizard appears. Follow the instructions to complete the driver installation.

Installing the Cisco Microsoft Windows Vista USB Driver

Step 1 Obtain the file Cisco_usbconsole_driver.zip from Cisco.com, and unzip it.

Note You can download the driver file from the Cisco.com software download site.

Step 2 If using32-bitWindows Vista,double-clickthe setup.exe file in the Windows_32 folder. If using64-bitWindows Vista,double-clickthe setup(x64).exe file in the Windows_64 folder.

Step 3 The Cisco Virtual Com InstallShield Wizard begins. ClickNext.

Step 4 The Ready to Install the Program window appears. ClickInstall.

Note If a User Account Control warning appears, clickAllow - I trust this program.

Step 5 The InstallShield Wizard Completed window appears. ClickFinish.

Step 6 Connect the USB cable to the PC and to the switch console port. The USB console port LED turns green, and the Found New Hardware Wizard appears. Follow the instructions to complete the driver installation.

Uninstalling the Cisco Microsoft Windows USB Drivers

Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver

The driver can be removed with the Windows Add or Remove Programs utility or with the setup.exe file.

Using the Add or Remove Programs Utility

Note Disconnect the switch console terminal before uninstalling the driver.

Step 1 Choose Start> Control Panel> Add or RemovePrograms.

Step 2 Scroll to Cisco Virtual Com, and clickRemove.

Step 3 When the Program Maintenance window appears, select theRemove radio button. ClickNext.

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

C-5

 

Appendix C Configuring the Switch with the CLI Setup Program

Accessing the CLI Through the Console Port

Using the Setup.exe Program

Note Disconnect the switch console terminal before uninstalling the driver.

Step 1 Run setup.exe for Windows32-bitor setup(x64).exe forWindows-64-bit.ClickNext.

Step 2 The InstallShield Wizard for Cisco Virtual Com appears. ClickNext.

Step 3 When the Program Maintenance window appears, select theRemove radio button. ClickNext.

Step 4 When the Remove the Program window appears, clickRemove.

Step 5 When the InstallShield Wizard Completed window appears, clickFinish.

Uninstalling the Cisco Microsoft Windows Vista USB Driver

Note Disconnect the switch console terminal before uninstalling the driver.

Step 1 Run setup.exe for Windows32-bitor setup(x64).exe forWindows-64bit.ClickNext.

Step 2 The InstallShield Wizard for Cisco Virtual Com appears. ClickNext.

Step 3 When the Program Maintenance window appears, select theRemove radio button. ClickNext.

Step 4 When the Remove the Program window appears, clickRemove.

Note If a User Account Control warning appears, clickAllow - I trust this program to proceed.

Step 5 When the InstallShield Wizard Completed window appears, clickFinish.

Cisco IE 3010 Switch Hardware Installation Guide

 

C-6

78-19581-02

 

 

 

Appendix C Configuring the Switch with the CLI Setup Program

Entering the Initial Configuration Information

Entering the Initial Configuration Information

To set up the switch, you need to complete the setup program, which runs automatically after the switch powers on. You must assign an IP address and other configuration information necessary for the switch to communicate with the local routers and the Internet.

IP Settings

You need this information:

Switch IP address

Subnet mask (IP netmask)

Default gateway (router)

Enable secret password

Enable password

Telnet password

Completing the Setup Program

Follow these steps to complete the setup program and to create an initial configuration for the switch:

Step 1 EnterYes at these two prompts.

Would you like to enter the initial configuration dialog? [yes/no]: yes

At any point you may enter a question mark '?' for help.

Use ctrl-cto abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Basic management setup configures only enough connectivity for management of the system, extended setup will ask you to configure each interface on the system.

Would you like to enter basic management setup? [yes/no]: yes

Step 2 Enter a host name for the switch, and pressReturn.

On a command switch, the host name is limited to 28 characters and on a member switch to 31 characters. Do not use -n,wheren is a number, as the last character in a host name for any switch.

Enter host name [Switch]: host_name

Step 3 Enter an enable secret password, and pressReturn.

The password can be from 1 to 25 alphanumeric characters, can start with a number, is case sensitive, allows spaces, but ignores leading spaces. The secret password is encrypted, and the enable password is in plain text.

Enter enable secret: secret_password

Step 4 Enter an enable password, and pressReturn.

Enter enable password: enable_password

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

C-7

 

Appendix C Configuring the Switch with the CLI Setup Program

Entering the Initial Configuration Information

Step 5 Enter a virtual terminal (Telnet) password, and pressReturn.

The password can be from 1 to 25 alphanumeric characters, is case sensitive, allows spaces, but ignores leading spaces.

Enter virtual terminal password: terminal-password

Step 6 (Optional) Configure Simple Network Management Protocol (SNMP) by responding to the prompts. You can also configure SNMP later through the CLI. To configure SNMP later, enterno.

Configure SNMP Network Management? [no]: no

Step 7 Enter the interface name (physical interface or VLAN name) of the interface that connects to the management network, and pressReturn. For this release, always use vlan1 as that interface.

Enter interface name used to connect to the

management network from the above interface summary: vlan1

Step 8 Configure the interface by entering the switch IP address and subnet mask and pressingReturn. The IP address and subnet masks shown below are examples.

Configuring interface vlan1:

Configure IP on this interface? [yes]: yes

IP address for this interface: 10.4.120.106

Subnet mask for this interface [255.0.0.0]: 255.0.0.0

Step 9 EnterY to configure the switch as the cluster command switch. EnterN to configure it as a member switch or as a standalone switch.

If you enter N, you can configure the switch as a command switch later through the CLI. To configure it later, enterno.

Would you like to enable as a cluster command switch? [yes/no]: no

You have completed the initial configuration of the switch, and the switch displays its configuration. This is an example of the configuration output:

The following configuration command script was created: hostname switch1

enable secret 5 $1$Ulq8$DlA/OiaEbl90WcBPd9cOn1 enable password enable_password

line vty 0 15

password terminal-passwordno snmp-server

!

no ip routing

!

interface Vlan1 no shutdown

ip address 10.4.120.106 255.0.0.0

!

interface FastEthernet1/0/1

!

interface FastEthernet1/0/2

interface FastEthernet1/0/3

!

...<output abbreviated> end

Cisco IE 3010 Switch Hardware Installation Guide

 

C-8

78-19581-02

 

 

 

Appendix C Configuring the Switch with the CLI Setup Program

Entering the Initial Configuration Information

Step 10 These choices appear:

[0]Go to the IOS command prompt without saving this config.

[1]Return back to the setup without saving this config.

[2]Save this configuration to nvram and exit.

If you want to save the configuration and use it the next time the switch reboots, select option 2 to save it in NVRAM.

Enter your selection [2]:2

Make your selection, and press Return.

After you complete the setup program, the switch can run the default configuration that you created. To change this configuration or to perform other management tasks, enter commands at the Switch> prompt.

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

C-9

 

Appendix C Configuring the Switch with the CLI Setup Program

Entering the Initial Configuration Information

 

Cisco IE 3010 Switch Hardware Installation Guide

C-10

78-19581-02

I N D E X

Numerics

 

C

10/100/1000 ports

1-11, B-3

cable guide, attaching 2-15

cable lengths

2-25

cable lengths 2-3

connecting to

2-25

cables

recommended cables 2-26

crossover

 

 

 

10/100 ports

 

four twisted-pairpinout,1000BASE-Tports

B-6

described

1-3

identifying

B-7

 

10/100 ports PoE 1-4

two twisted-pairpinout, 10/100 portsB-6

 

 

 

crossover, connecting to B-2

 

 

 

pinouts B-6

 

 

 

A

 

 

 

 

 

recommended

2-26

 

 

 

 

adapter pinouts, terminal

See also connectors

 

RJ-45-to-DB-25B-7

SFP module

B-4

 

 

RJ-45-to-DB-9B-7

straight-through

 

 

alarm port

 

connecting to

B-2

 

connectors

B-3

four twisted-pairpinout,1000BASE-Tports

B-6

input 1-6

 

two twisted-pairpinoutB-6

 

 

output

1-7

 

 

 

cable side

 

 

 

 

 

 

alarm ratings

A-5

 

 

 

10/100 ports

1-3

 

 

 

 

 

Attaching Brackets for 19-InchRacks

2-5

 

description

1-2

 

 

 

 

 

Attaching Brackets for 19-InchRacks forIP-30

 

LEDs 1-8

 

 

 

 

 

 

Compliance (Optional) 2-6

 

 

PoE ports 1-4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Attaching Brackets for 23-InchRacks

2-12

 

Cisco IOS command-lineinterface

1-14

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Attaching Brackets for ETSI Racks

2-13

 

Cisco IP Phones, connecting to 1-4, 2-26

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Attaching Brackets for IP-30Compliance (Optional)

2-16

Cisco Power Calculator 2-26

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

autonegotiation

 

 

 

CLI 1-14

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

default setting

2-25

 

 

accessing through the RJ-45console port

 

C-1

 

 

 

 

 

 

 

 

on dual-purposeports1-3

 

 

accessing through the USB console port

C-3

 

 

 

 

 

 

 

troubleshooting

4-4

 

 

command-lineinterface

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

See CLI

 

 

 

 

 

 

 

 

 

 

 

 

connecting

 

 

 

 

 

 

 

 

 

 

 

 

10/100 and 10/100/1000 ports

2-25

 

 

 

 

 

 

 

 

 

 

Cisco IE 3010 Switch Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

78-19581-02

 

 

 

 

 

 

 

 

 

IN-1

 

 

 

 

 

 

 

 

 

 

 

 

Index

10/100 PoE ports

2-26

 

to AC and DC power

3-12

to console port

B-7

 

connection procedures

2-25 to 2-26

connectors

 

 

 

 

alarm port

B-3

 

 

 

dual-purposeports

B-3

SFP module connectors

B-2

console port

 

 

 

 

connecting to

B-7

 

 

described

B-7

 

 

 

overview

1-7

 

 

 

RJ-45console port

1-7

USB console port

1-7

 

crossover cable

 

 

 

 

pinout

 

 

 

 

four twisted-pair,1000BASE-TportsB-6

D

diagnosing problems

4-1

dimensions

A-4

 

disconnect device warning 3-8

dual-purposeports

 

description 1-4

 

LEDs

1-11

 

duplex

 

 

default setting

2-25

troubleshooting

4-4

E

EN50155 standard compliance warning

2-4, 2-15

Ethernet and fiber cable troubleshooting

4-2

G

ground conductor warning 3-5

Cisco IE 3010 Switch Hardware Installation Guide

ground connection warning 3-5

H

HP OpenView 1-14

I

installation

 

 

assigning the IP Address

C-7

Cisco USB drivers

C-4

 

grounding procedures 3-4

guidelines 2-3

 

 

power supply modules

3-6

rack-mounting2-4

 

site requirements

2-3

 

starting the terminal emulation software C-1, C-3

wall-mounting2-15

 

See also procedures

 

installation warnings

2-1

 

IP-30compliance forrack-mounting2-6

J

jewelry removal warning 2-1

L

LEDs

alarms

1-9, 1-11

 

 

console

1-10

 

 

descriptions and locations

1-8 to 1-11

dual-purposeport

1-11

 

POST results 4-1

 

 

PSU 1 and PSU 2

1-9

 

SD Flash Memory Card

1-11

system

1-9

 

 

troubleshooting with 4-1 to 4-2

IN-2

78-19581-02

Index

lightning activity warning

2-2, 3-3

link status troubleshooting

4-2

M

mounting

rack 2-4

wall 2-15

O

overcurrent protection warning 3-8

P

pinouts

 

 

 

 

 

10/100 ports

B-2

 

 

 

 

console port

B-8

 

 

 

 

crossover cables

 

 

 

 

four twisted-pair,1000BASE-Tports

B-6

two twisted-pair10/100 ports

B-6

 

RJ-45-to-DB-25terminal adapter

B-8

 

RJ-45-to-DB-9terminal adapter

B-7

 

SFP module ports

B-2

 

 

straight-throughcables

 

 

four twisted-pair1000BASE-Tports

B-6

two twisted-pair

B-6

 

 

PoE

 

 

 

 

 

cable lengths

1-4

 

 

 

ports described 1-4

 

 

 

power planning tool

2-26

 

 

shock hazard warning

2-26

 

 

troubleshooting

4-3

 

 

 

ports

 

 

 

 

 

1-3

 

 

 

 

 

10/100/1000

1-11, B-3

 

 

connecting to

2-25

 

 

10/100 PoE

 

 

 

 

See also PoE

 

 

dual-purpose1-4

 

 

LEDs

1-10

 

 

 

 

SFP module

1-5

 

 

POST

 

 

 

 

 

description

4-1

 

 

 

LEDs

4-1

 

 

 

 

power-inputterminal

 

 

description

1-6

 

 

 

wiring

3-7

 

 

 

 

power specifications

A-4

 

 

power-supplymodules

 

 

description

1-12

 

 

features

1-14

 

 

 

grounding the switch

3-3

 

installation guidelines

3-3, 3-12

installing AC or DC

3-4 to 3-12

specifications

A-4

 

 

wiring the power source

3-7

power-supplyside description

1-12

procedures

 

 

 

 

 

connection

2-25 to 2-26

 

PSU 1 and PSU 2 LEDs

1-9

 

publications, related

i-viii

 

R

rack-mounting2-4 to 2-15

rack-mountingforIP-30compliance2-6 removing SFP modules2-21

RJ-45connector

alarm input port B-3 console portB-7

S

 

recommended cables 2-26

safety 2-1

 

 

Cisco IE 3010 Switch Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

78-19581-02

 

 

IN-3

 

 

 

 

 

3-5
3-5
2-2
2-2
2-15
2-4, 2-15

Index

SD flash memory card

1-11

 

 

 

overview

1-11

 

 

 

 

replacing

2-23

 

 

 

 

serial number location

4-5

 

 

 

setup program

C-7

 

 

 

 

SFP module patch cable

 

 

 

description

1-6

 

 

 

 

installing

2-21

 

 

 

 

removing

2-22

 

 

 

 

SFP modules

 

 

 

 

 

 

bale-clasplatch removal

2-21

 

connectors

B-2

 

 

 

 

installing

2-20

 

 

 

 

removing

2-21

 

 

 

 

supported

1-4

 

 

 

 

 

SFP module slots

1-5

 

 

 

short-circuitprotection warning

3-8

 

Simple Network Management Protocol

 

See SNMP

 

 

 

 

 

 

SNMP network management platforms

1-14

software switch management

1-14

 

specifications

A-1 to A-4

 

 

 

speed

 

 

 

 

 

 

default setting

2-25

 

 

 

troubleshooting

4-4

 

 

 

straight-throughcable pinout

 

 

 

four twisted-pair1000BASE-Tports

B-6

two twisted-pair10/100 ports

B-6

 

SunNet Manager

1-14

 

 

 

switch models

1-1

 

 

 

 

switch models illustrated 1-2

T

technical specifications A-1 to A-4

Telnet, and accessing the CLI 1-14 temperature, operatingA-1 troubleshooting

bad or damaged cable 4-2

connection problems

4-2

diagnosing problems

4-1

Ethernet and fiber cables 4-2

link status 4-2

 

 

ping end device

4-3

 

PoE connections

4-3

 

POST 4-1

 

 

serial number location

4-5

spanning tree loops 4-4

speed, duplex, and autonegotiation 4-4 switch performance4-4

with LEDs 4-1 to 4-2

U

uninstalling the Cisco Microsoft Windows USB driver C-5

USB console port overview 1-7

W

wall-mounting

Wall-Mountingthe Switch2-18 wall-mountingwarning2-15 warnings

airflow restriction

ambient temperature EN50155 standard compliance ground conductor

ground connection installation 2-1 jewelry removal2-1

lightning activity 2-2, 3-3

national laws and regulations 2-2

PoE shock hazard

2-26

qualified personnel

2-2

restricted access areas 2-1

short-circuit(overcurrent) protection3-8

Cisco IE 3010 Switch Hardware Installation Guide

 

IN-4

78-19581-02

 

 

 

Index

two-poleddisconnect device3-8

wall-mounting2-15

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

IN-5

 

Index

Cisco IE 3010 Switch Hardware Installation Guide

 

IN-6

78-19581-02