WORLD WIDE
F15A
F9.9C, FT9.9D
USA/CANADA
F15
SERVICE MANUAL |
E |
MANUEL D’ENTRETIEN |
F |
WARTUNGSANLEITUNG |
D |
MANUAL DE SERVICIO |
ES |
66M-28197-Z8-C1
E
NOTICE
This manual has been prepared by the Yamaha Motor Company, Ltd. primarily for use by Yamaha dealers and their trained mechanics when performing maintenance procedures and repairs to Yamaha equipment. It has been written to suit the needs of persons who have a basic understanding of the mechanical and electrical concepts and procedures inherent in the work, for without such knowledge attempted repairs or service to the equipment could render it unsafe or unfit for use.
Because the Yamaha Motor Company, Ltd. has a policy of continuously improving its products, models may differ in detail from the descriptions and illustrations given in this publication. Use only the latest edition of this manual. Authorized Yamaha dealers are notified periodically of modifications and significant changes in specifications and procedures, and these are incorporated in successive editions of this manual.
A10001-0*
F15A/F9.9C/FT9.9D
(F15) SERVICE MANUAL
©1998 Yamaha Motor Co.,Ltd.
1st Edition, April 1998 All rights reserved.
No part of this publication may be reproduced or transmitted in any form or by any means including photocopying and recording without the written permission of the copyright holder.
Such written permission must also be obtained before any part of this publication is stored in a retrieval system of any nature. Printed in Japan
P/N 66M-28197-Z8-C1
F |
D |
ES |
AVANT PROPOS
La Yamaha Motor Company a élaboré ce manuel à l’attention des concessionnaires Yamaha et de leurs mécaniciens pour leurs travaux d’entretien et de réparation sur du matériel Yamaha. Ce manuel s’adresse à des personnes disposant de connaissances de base solides en mécanique et en électricité Sans lesquelles elles risqueraient, au cours de leurs travaux de réparation ou d’entretien, de rendre le matériel inapte ou dangereux à l’utilisation.
La politique de la Yamaha Motor Company Ltd. visant à l’amélioration constante de ses produits, il est possible que le modèle devant faire l’objet d’une réparation ne corresponde pas exactement au modèle présenté. N’utilisez que l’édition la plus récente de ce manuel. Les concessionnaires agréés Yamaha sont régulièrement informés de toutes les modifications importantes apportées à Notre matériel. Il est tenu compte de ces modifications dans les éditions successives de ce manuel.
F15A/F9.9C/FT9.9D
(F15) MANUEL D’ENTRETIEN
©1998 Yamaha Motor Co., Ltd. 1 ère édition, avril 1998 Tous droits réservés.
Toute reproduction ou transmission de ce manuel, même partielle, par quelque procédé que ce soit, y compris par photocopie ou enregistrement, requiert l’accord écrit préalable de la Yamaha Motor Co., Ltd. Imprimé au Japon
P/N 66M-28197-Z8-C1
EINFÜHRUNG |
AVISO |
Dieses Handbuch wurde von der Yamaha Motor Company vorrangig zur Verwendung durch die YamahaVertragshändler und ihre qualifizierten Mechaniker geschrieben. Es ist nicht möglich, den gesamten Ausbildungsumfang von Mechanikern in einem einzigen Handbuch zusammenzufassen.
Darum werden in diesem Handbuch Grundkenntnisse des mechanischen und elektrischen Aufbaus und der zur Wartung nötigen Arbeitsmethoden vorausgesetzt. Versuchte Wartungsund Reparaturarbeiten ohne solche Kenntnisse könnten den Außenbordmotor unsicher und/oder verwendungsunfähig machen.
Die Yamaha Motor Company, Ltd. ist immer danach bestrebt, alle von Yamaha hergestellten Modelle zu verbessern. Spezifikationen oder Verfahren werden allen YamahaVertragshändlern mitgeteilt und werden ggf. in zukünftigen Ausgaben dieses Handbuchs erscheinen.
F15A/F9.9C/FT9.9D
(F15) WARTUNGSHANDBUCH ©1998 Yamaha Motor Co., Ltd. 1. Ausgabe, April 1998
Alle Rechte vorbehalten. Diese Veröffentlichung darf auch
teilweise in keiner Weise oder durch irgendein Verfahren ohne die schriftliche Genehmigung des Inhabers des Urheberrechts reproduziert oder übertragen werden. Dies gilt auch für Fotokopien und Aufzeichnungen. Die schriftliche Genehmigung ist vor der ÜbErnahme in irgendein Informationssystem einzuholen. Gedruckt in Japan
P/N 66M-28197-Z8-C1
Este manual ha sido preparado por Yamaha Motor Company y va dirigido a los concesionarios Yamaha y a sus mecánicos cualificados para realizar los procedimientos de mantenimiento y las reparaciones de los equipos Yamaha. Está redactado de forma que pueda satisfacer las necesidades de aquellas personas que poseen unos conocimientos básicos de los conceptos y procedimientos mecánicos y eléctricos inherentes a dichos trabajos de mantenimiento y reparación, ya que de no poseer tales conocimientos, las posibles reparaciones o mantenimiento del equipo podrían afectar adversamente su seguridad y operatividad.
Puesto que Yamaha Motor Company Ltd. sigue una política de mejora continua de sus productos, puede que las especificaciones de los modelos no coincidan con algunos aspectos de las descripciones e ilustraciones contenidos en esta publicación. Utilice únicamente la versión más reciente de este manual. Los concesionarios autorizados Yamaha reciben periódicamente información relacionada a las modificaciones y cambios significativos introducidos en las especificaciones y los procedimientos de los equipos, información que se incorporará a las ediciones sucesivas de este manual.
F15A/F9.9C/FT9.9D
(F15) MANUAL DE SERVICIO
©1998 Yamaha Motor Co., Ltd. 1ª Edición, abril 1998 Reservados todos los derechos.
Queda prohibida la reproducción o transmisión de esta publicación, ya sea en su totalidad o en parte, y por cualquier medio, incluido su fotocopiado o grabación, sin el consentimiento por escrito del titular del derecho de copyright. También deberá obtenerse este consentimiento antes de proceder al almacenamiento de cualquier parte de esta publicación en un
sistema de búsqueda documental de cualquier naturaleza.
Impreso en Japón P/N° 66M-28197-Z8-C1
E
MANUAL FORMAT
All of the procedures in this manual are organized in a sequential, step-by-step format. The information has been compiled to provide the mechanic with an easy to read, handy reference that contains comprehensive explanations of all disassembly, repair, assembly, and inspection operations.
In this revised format, the condition of a faulty component will precede an arrow symbol and the course of action required will follow the symbol, e.g.,
8Bearings
Pitting/Scratches → Replace.
To assist you to find your way through this manual, the section title and major heading are given at the top of every page.
IILUSTRATIONS
The illustrations within this service manual represent all of the designated models.
CROSS REFERENCE
The cross references have been kept to a minimum. Cross references will direct you to the appropriate section or chapter.
F |
D |
ES |
MODE D’UTILISATION DU MANUEL
PRESENTATION DU MANUEL
Dans ce manuel, tous les procédés sont décrits pas à pas. Les informations ont été condensées pour fournir au mécanicien un guide pratique et facile à lire, contenant des explications claires pour tous les procédés de démontage, réparation, remontage et vérification.
Dans ce nouveau format, l’état d’un composant défectueux est suivi d’une flèche qui indique les mesures à prendre. Exemple:
9Roulements Piqûres/Endommagement →
Changer.
Pour plus de facilité, le titre de chapitre ainsi que le titre de section sont repris en tête de chaque page.
ILLUSTRATIONS
Les illustrations contenues dans ce manuel de service représentent tous les modèles concernés.
REFERENCES CROISEES
Les références ont été réduites à un minimum. Les références croisées vous renvoient directement à la section ou au chapitre approprié.
LEITFADEN FÜR
DIESES HANDBUCH
AUFBAU DES HANDBUCHS
Dieses Handbuch enthält Beschreibungen von Arbeitsverfahren, die für Demontage, Reparatur, Montage, Einstellung und Inspektion eingesetzt werden. Alle Arbeiten werden der Reihe nach schrittweise dargestellt.
Der geänderte Aufbau gibt den Zustand eines schadhaften Bauteils vor einem Pfeilsymbol an. Die erforderlichen Maßnahmen werden nach dem Symbol beschrieben, z.B:
9Lager Lochfraß/Beschädigung →
Ersetzen.
Um Ihnen das Auffinden von gewünschten Stellen in dem Handbuch zu erleichtern, ist oben auf jeder Seite der Titel des Kapitels und betreffenden Abschnitts aufgeführt.
ABBILDUNGEN
Die Abbildungen in diesem Kundendiensthandbuch beziehen sich auf alle Modelle.
QUERVERWEISE
Querverweise sind auf ein Mindestmaß begrenzt. Sie führen Sie zum entsprechenden Abschnitt oder Kapitel.
COMO UTILIZAR
ESTE MANUAL
FORMATO DEL MANUAL
Todos los procedimientos de este manual están preparados en un formato secuencial de paso a paso.
La información ha sido compilada para ofrecer al mecánico una referencia útil y de fácil lectura que contiene amplias explicaciones de todos los procedimientos de desmontaje, reparación, montaje, e inspecciones.
En este formato revisado, la condición de un componente averiado irá precedida de un símbolo de flecha y el curso de la acción requerida seguirá al símbolo, como por ejemplo:
9Cojinetes
Picaduras/Daños → Reemplazar.
Para ayudarle a orientarse a través de este manual, en la parte superior de cada página figuran el título
de la sección y el encabezamiento principal.
FIGURAS
Las figuras que aparecen en este manual de servicio representan todos los modelos designados.
REFERENCIAS CRUZADAS
Las referencias cruzadas se han reducido al mínimo y le dirigen al apartado o capítulo correcto.
E
IMPORTANT INFORMATION
In this Service Manual particularly important information is distinguished in the following ways.
QThe Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
w
Failure to follow WARNING instructions could result in severe injury or death to the machine operator, a bystander, or a person inspecting or repairing the outboard motor.
cC
A CAUTION indicates special precautions that must be taken to avoid damage to the outboard motor.
NOTE:
A NOTE provides key information to make procedures easier or clearer.
SPECIFIC COMPARISON
The following tables show the main differences in specifications between models.
Model |
USA/CANADA |
|
|
||
Item |
F15MHX |
F15EHX |
|
|
|
Steering friction |
1 |
|
1 |
|
|
Steering hook |
— |
|
— |
|
|
Ring gear |
1( CANADA— |
) |
1 |
|
|
Lighting current |
AC 6A (12V-80W) |
— |
|
|
|
Charging current |
— |
|
10A |
|
|
Rectifier |
— |
|
— |
|
|
Rectifier/regulator |
— |
6G8-A1 |
|
|
|
Fuse |
— |
|
20A |
|
|
Model |
|
EUROPE |
|
OCEANIA |
|
Item |
F15AMH |
F15AEH |
F15AE |
F15AMH |
F15AEH |
Steering friction |
— |
— |
— |
— |
— |
Steering hook |
— |
— |
1 |
— |
— |
Ring gear |
— |
1 |
1 |
— |
1 |
Lighting current |
12V-80W |
— |
— |
AC 6A (12V-80W) |
— |
Charging current |
6A |
6A |
10A |
— |
10A |
Rectifier |
— |
6G1 |
— |
— |
— |
Rectifier/regulator |
6J8 |
— |
6G8-A1 |
— |
6G8-A1 |
Fuse |
— |
10A |
20A |
— |
20A |
E
Model |
|
EUROPE |
|
|
|
Item |
F9.9CMH |
F9.9CEH |
F9.9CE |
|
|
Steering friction |
— |
— |
— |
|
|
Steering hook |
— |
— |
1 |
|
|
Ring gear |
— |
1 |
1 |
|
|
Lighting current |
12V-80W |
— |
— |
|
|
Charging current |
6A |
6A |
10A |
|
|
Rectifier |
— |
6G1 |
— |
|
|
Rectifier/regulator |
6J8 |
— |
6G8-A1 |
|
|
Fuse |
— |
10A |
20A |
|
|
Model |
|
EUROPE |
|
OCEANIA |
|
Item |
FT9.9DMH |
FT9.9DEH |
FT9.9DE |
FT9.9DMH |
FT9.9DE |
Steering friction |
1 |
1 |
1 |
1 |
1 |
Steering hook |
— |
— |
1 |
— |
1 |
Ring gear |
— |
1 |
1 |
— |
1 |
Lighting current |
— |
— |
— |
— |
— |
Charging current |
10A |
10A |
10A |
10A |
10A |
Rectifier |
— |
— |
— |
— |
— |
Rectifier/regulator |
6G8-A1 |
6G8-A1 6G8-A1 |
6G8-A1 |
6G8-A1 |
|
Fuse |
— |
20A |
20A |
— |
20A |
F
INFORMATIONS IMPORTANTES
Les informations plus particulièrement importantes présentées dans ce manuel de service sont mises en évidence de la façon suivante.
QCe symbole signale un danger : ATTENTION DANGER ! SOYEZ ATTENTIF ! VOTRE SECURITE EST EN JEU !
XG
Le respect des consignes AVERTISSEMENT est impératif, faute de quoi le conducteur, toute personne se trouvant à proximité ou le personnel chargé de l’entretien du moteur hors-bord risquerait d’être grièvement voire mortellement blessé.
fF
ATTENTION indique les consignes qui doivent être respectées afin d’éviter d’endommager le moteur hors-bord.
N.B.:
N.B. donne des informations importantes qui facilitent et expliquent les différentes opérations.
COMPARAISONS SPECIFIQUES
Les tableaux suivants montrent les principales différences de spécification entre modèles.
Modèle |
E.-U./CANADA |
|
|
||
Désignation |
F15MHX |
|
F15EHX |
|
|
Friction de la direction |
1 |
|
1 |
|
|
Support de barre franche |
— |
|
— |
|
|
Couronne |
1( CANADA— |
) |
1 |
|
|
Courant d’éclairage |
AC 6A (12V-80W) |
— |
|
|
|
Courant de charge |
— |
|
10A |
|
|
Redresseur |
— |
|
— |
|
|
Redresseur/régulateur |
— |
|
6G8-A1 |
|
|
Fusible |
— |
|
20A |
|
|
Modèle |
|
EUROPE |
|
|
OCEANIE |
Désignation |
F15AMH |
F15AEH |
F15AE |
F15AMH |
F15AEH |
Friction de la direction |
— |
— |
— |
— |
— |
Support de barre franche |
— |
— |
1 |
— |
— |
Couronne |
— |
1 |
1 |
— |
1 |
Courant d’éclairage |
12V-80W |
— |
— |
AC 6A (12V-80W) |
— |
Courant de charge |
6A |
6A |
10A |
— |
10A |
Redresseur |
— |
6G1 |
— |
— |
— |
Redresseur/régulateur |
6J8 |
— |
6G8-A1 |
— |
6G8-A1 |
Fusible |
— |
10A |
20A |
— |
20A |
F
Modèle |
|
|
EUROPE |
|
|
|
|
|
|
|
|
|
|
Désignation |
F9.9CMH |
|
F9.9CEH |
F9.9CE |
|
|
|
|
|
|
|
|
|
Friction de la direction |
— |
|
— |
— |
|
|
Support de barre franche |
— |
|
— |
1 |
|
|
Couronne |
— |
1 |
1 |
|
|
|
Courant d’éclairage |
12V-80W |
|
— |
— |
|
|
Courant de charge |
6A |
|
6A |
10A |
|
|
Redresseur |
— |
|
6G1 |
— |
|
|
Redresseur/régulateur |
6J8 |
|
— |
6G8-A1 |
|
|
Fusible |
— |
|
10A |
20A |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Modèle |
|
|
EUROPE |
|
|
OCEANIE |
Désignation |
FT9.9DMH |
|
FT9.9DEH |
FT9.9DE |
FT9.9DMH |
FT9.9DE |
|
||||||
|
|
|
|
|
|
|
Friction de la direction |
1 |
|
1 |
1 |
1 |
1 |
Support de barre franche |
— |
|
— |
1 |
— |
1 |
Couronne |
— |
|
1 |
1 |
— |
1 |
Courant d’éclairage |
— |
|
— |
— |
— |
— |
Courant de charge |
10A |
|
10A |
10A |
10A |
10A |
Redresseur |
— |
|
— |
— |
— |
— |
Redresseur/régulateur |
6G8-A1 |
|
6G8-A1 |
6G8-A1 |
6G8-A1 |
6G8-A1 |
Fusible |
— |
|
20A |
20A |
— |
20A |
|
|
|
|
|
|
|
D
WICHTIGER HINWEIS
In diesem Kundendiensthandbuch werden wichtige Hinweise folgendermaßen hervorgehoben.
QDas Achtungsschild bedeutet: ACHTUNG! AUFGEPASST! ES GEHT UM IHRE SICHERHEIT!
W
Ein Nichtbefolgen der Warnhinweise kann ernsthafte Verletzungen und sogar den Tod zur Folge haben. Dies gilt für Bediener, Zuschauer und am Motor arbeitende Techniker gleichermaßen.
dD
DUnter dieser Überschrift ergehen Hinweise auf Vorsichtsmaßnahmen zum Schutze des Motors.
HINWEIS:
Hier geht es um nützliche Tips und Hinweise.
SPEZIFISCHE VERGLEICHE
Die folgenden Tabellen zeigen die Hauptunterschiede in den technischen Daten verschiedener Modelle.
Modell |
USA/KANADA |
||
Teil |
F15MHX |
|
F15EHX |
Schublenkantrieb |
1 |
|
1 |
Lenkhaken |
— |
|
— |
Tellerrad |
1( KANADA— |
) |
1 |
Lichtstrom |
AC 6A (12V-80W) |
— |
|
Ladestrom |
— |
|
10A |
Gleichrichter |
— |
|
— |
Gleichrichter/Regler |
— |
|
6G8-A1 |
Sicherung |
— |
|
20A |
Modell |
|
EUROPA |
OZEANIEN |
Teil |
F15AMH |
F15AEH |
F15AE |
F15AMH |
F15AEH |
|
|
|
|
|
|
Schublenkantrieb |
— |
— |
— |
— |
— |
Lenkhaken |
— |
— |
1 |
— |
— |
Tellerrad |
— |
1 |
1 |
— |
1 |
Lichtstrom |
12V-80W |
— |
— |
AC 6A (12V-80W) |
— |
Ladestrom |
6A |
6A |
10A |
— |
10A |
Gleichrichter |
— |
6G1 |
— |
— |
— |
Gleichrichter/Regler |
6J8 |
— |
6G8-A1 |
— |
6G8-A1 |
Sicherung |
— |
10A |
20A |
— |
20A |
D
Modell |
|
EUROPE |
|
Teil |
F9.9CMH |
F9.9CEH |
F9.9CE |
Schublenkantrieb |
— |
— |
— |
Lenkhaken |
— |
— |
1 |
Tellerrad |
— |
1 |
1 |
Lichtstrom |
12V-80W |
— |
— |
Ladestrom |
6A |
6A |
10A |
Gleichrichter |
— |
6G1 |
— |
Gleichrichter/Regler |
6J8 |
— |
6G8-A1 |
Sicherung |
— |
10A |
20A |
Modell |
|
EUROPA |
|
|
OZEANIEN |
Teil |
FT9.9DMH |
FT9.9DEH |
FT9.9DE |
FT9.9DMH |
FT9.9DE |
Schublenkantrieb |
1 |
1 |
1 |
1 |
1 |
Lenkhaken |
— |
— |
1 |
— |
1 |
Tellerrad |
— |
1 |
1 |
— |
1 |
Lichtstrom |
— |
— |
— |
— |
— |
Ladestrom |
10A |
10A |
10A |
10A |
10A |
Gleichrichter |
— |
— |
— |
— |
— |
Gleichrichter/Regler |
6G8-A1 |
6G8-A1 |
6G8-A1 |
6G8-A1 |
6G8-A1 |
Sicherung |
— |
20A |
20A |
— |
20A |
ES
INFORMACION IMPORTANTE
En este manual de servicio, la información especialmente importante se distingue de las siguientes maneras.
QEl símbolo de seguridad significa ¡ATENCION! ¡PERMANEZCA ALERTA! ¡SU SEGURIDAD ESTA EN JUEGO!
r
La no observancia de las instrucciones contenidas en un AVISO puede provocar graves lesiones o incluso la muerte del operador del motor fuera borda, de las personas que se encuentren a su alrededor o de la persona que inspeccione o repare el motor fuera borda.
bB
Una PRECAUCION indica cuidados especiales que deben tomarse para evitar dañar el motor fuera borda.
NOTA:
Una NOTA ofrece información clave para facilitar o aclarar los procedimientos.
COMPARACIONES ESPECIFICAS
Las tablas siguientes muestran las diferencias principales existentes entre los modelos en lo que a especificaciones se refiere.
Modelo |
EE.UU./CANADA |
|
|
||
Elemento |
F15MHX |
|
F15EHX |
|
|
Fricción de la dirección |
1 |
|
1 |
|
|
Gancho de la dirección |
— |
|
— |
|
|
Anillo dentado |
1( CANADA— |
) |
1 |
|
|
Corriente de alumbrado |
AC 6A (12V-80W) |
— |
|
|
|
Corriente de carga |
— |
|
10A |
|
|
Rectificador |
— |
|
— |
|
|
Rectifire/regurator |
— |
|
6G8-A1 |
|
|
Fusible |
— |
|
20A |
|
|
Modelo |
|
EUROPA |
|
OCEANIA |
|
Elemento |
F15AMH |
F15AEH |
F15AE |
F15AMH |
F15AEH |
Fricción de la dirección |
— |
— |
— |
— |
— |
Gancho de la dirección |
— |
— |
1 |
— |
— |
Anillo dentado |
— |
1 |
1 |
— |
1 |
Corriente de alumbrado |
12V-80W |
— |
— |
AC 6A (12V-80W) |
— |
Corriente de carga |
6A |
6A |
10A |
— |
10A |
Rectificador |
— |
6G1 |
— |
— |
— |
Regulador/rectificador |
6J8 |
— |
6G8-A1 |
— |
6G8-A1 |
Fusible |
— |
10A |
20A |
— |
20A |
ES
Modelo |
|
EUROPE |
|
|
|
Elemento |
F9.9CMH |
F9.9CEH |
F9.9CE |
|
|
Fricción de la dirección |
— |
— |
— |
|
|
Gancho de la dirección |
— |
— |
1 |
|
|
Anillo dentado |
— |
1 |
1 |
|
|
Corriente de alumbrado |
12V-80W |
— |
— |
|
|
Corriente de carga |
6A |
6A |
10A |
|
|
Rectificador |
— |
6G1 |
— |
|
|
Regulador/rectificador |
6J8 |
— |
6G8-A1 |
|
|
Fusible |
— |
10A |
20A |
|
|
Modelo |
|
EUROPA |
|
|
OCEANIA |
Elemento |
FT9.9DMH |
FT9.9DEH |
FT9.9DE |
FT9.9DMH |
FT9.9DE |
Fricción de la dirección |
1 |
1 |
1 |
1 |
1 |
Gancho de la dirección |
— |
— |
1 |
— |
1 |
Anillo dentado |
— |
1 |
1 |
— |
1 |
Corriente de alumbrado |
— |
— |
— |
— |
— |
Corriente de carga |
10A |
10A |
10A |
10A |
10A |
Rectificador |
— |
— |
— |
— |
— |
Regulador/rectificador |
6G8-A1 |
6G8-A1 |
6G8-A1 |
6G8-A1 |
6G8-A1 |
Fusible |
— |
20A |
20A |
— |
20A |
E
HOW TO USE THIS MANUAL
1To help identify parts and clarify procedure steps, there are exploded diagrams at the start of each removal and disassembly section.
2Numbers are given in the order of the jobs in the exploded diagram. A circled number indicates a disassembly step.
3 Symbols indicate parts to be lubricated or replaced (see “SYMBOLS”).
4A job instruction chart accompanines the exploded daiagram, providing the order of jobs, names of parts, notes in jobs, etc.
Example: |
|
O-ring size |
39.5 x 2.5 mm: inside diameter (D) x ring diameter (d) |
5 Dimension figures and the number of parts are provided for fasteners that require a tight-
ening torque: |
|
Example: |
|
Bolt or screw size |
10 x 25 mm (2) : M10(D) x 25 mm (L) |
6 Jobs requiring more information (such as special tools and technical data) are described |
|||||||||
sequentially. |
|
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2 |
|
|
|
|
|
LOWR |
LOWER UNIT |
|
E |
LOWR |
PROPELLER SHAFT HOUSING ASS’Y |
E |
|||
LOWER UNIT |
|
|
|
A |
|
|
|
SERVICE POINTS |
|
EXPLODED DIAGRAM |
|
|
|
1 |
|
|
|
Propeller shaft housing ass’y disassembly |
|
|
|
|
|
|
|
|
|
1. Remove: |
|
|
|
|
|
|
|
|
|
9Reverse gear |
|
7 |
|
|
|
|
|
|
|
9reverse gear shim (s) |
|
|
11 |
|
|
|
|
|
9Ball bearing 1 |
|
|
|
|
17 Nm (1.7 m•kg, 12 ft•lb) |
|
|
|
|
|
||
6 |
|
|
|
|
|
|
|
|
|
|
|
|
2 |
|
|
|
Slide hammer set 2: |
6 |
|
|
|
|
2 |
|
|
|
|
YB-06096 |
|
|
|
|
8 |
|
|
|
|
Stopper guide plate 3: |
|
10 |
|
|
B |
|
|
|
90890-06501 |
|
|
|
|
1 |
4 |
|
|
Bearing puller 4: |
|
||
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
90890-06535 |
|
|
|
|
|
3 |
|
|
3 |
|
|
|
|
|
|
|
|
|
Stopper guide stand 5: |
|
||
|
|
|
5 |
|
|
|
|
|
|
|
|
|
|
|
|
|
90890-06538 |
|
|
|
|
|
|
|
|
5 |
|
|
|
|
|
|
4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
A For USA and CANADA |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
B Except for USA and CANADA |
|
13 |
|
|
|
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
14 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2. Remove: |
|
9 |
|
|
12 |
1 |
|
|
|
9Oil seals |
|
|
|
18 |
|
|
|
|
9Needle bearing |
|
|
|
|
|
|
|
|
|
|
||
|
|
|
17 |
|
|
|
2 |
|
|
|
|
|
|
|
|
|
Slide hammer set 1: |
|
|
3 |
14 |
|
16 |
|
|
|
3 |
|
|
|
15 |
|
|
|
YB-06096 |
|
|||
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
Driver rod 2: |
|
||
|
|
|
|
|
|
|
|
||
|
|
5 Nm (0.5 m•kg, 3.6 ft•lb) |
5 |
|
|
|
YB-06071/90890-06604 |
|
|
|
|
|
|
|
|
|
|
Needle bearing attachment 3: |
|
|
|
|
|
|
|
|
|
YB-06081/90890-06616 |
|
4 |
REMOVAL AND INSTALLATION CHART |
|
|
|
|
|
|
|
Gears inspection |
||||||
Step |
Procedure/Part name |
|
Q’ty |
|
Service points |
|
|
1. |
Inspect: |
||||||
|
|
LOWER REMOVAL |
|
|
|
Follow the left ”Step” for removal. |
|
|
|
|
9Tooth |
||||
|
|
|
|
|
|
|
|
|
9Dog |
||||||
|
1 |
Cotter pin |
|
|
1 |
|
Not reusable |
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
Wear/Damage → Replace. |
||||||
2 |
2 |
Propeller nut |
|
|
1 |
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
||||
3 |
Spacer |
|
|
1 |
|
|
|
|
|
|
|
|
|
|
|
4 |
Propeller |
|
|
1 |
|
|
|
|
|
|
|
|
|
|
|
|
5 |
Collar |
|
|
1 |
|
|
|
|
|
|
|
|
|
|
|
6 |
Locknut |
|
|
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
7 |
Adjusting nut |
|
|
1 |
|
|
|
|
|
|
Bearings inspection |
|||
|
8 |
Bolt (lower case) |
|
|
4 |
|
|
|
|
|
1. |
Inspect: |
|||
|
9 |
Lower unit |
|
|
1 |
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
9Bearing |
|||||
|
10 |
Dowel pins |
|
|
2 |
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
Pitting/Rumbling → Replace. |
|||||
|
11 |
Seal rubber |
|
|
1 |
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
NOTE: |
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
Turn the bearing by fingers and check the |
|||
|
|
|
|
|
|
|
|
|
|
|
|
bearing pitching |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
6-1 |
|
|
|
|
6-10 |
|
|
|
|
F |
D |
ES |
COMMENT UTILISER CE MANUEL
1Pour vous aider à identifier les composants et clarifier les différentes étapes des procédures, une vue éclatée est illustrée au début de chacune des procédures de dépose et de démontage.
2Les numéros indiqués dans la vue éclatée sont donnés dans l’ordre des opérations. Un numéro encerclé indique une étape de démontage.
3Les symboles indiquent les composants à lubrifier ou à remplacer (voir “SYMBOLES”).
4Un tableau d’instructions accompagne la vue éclatée de manière à fournir la séquence des opérations, le nom des composants, les remarques relatives aux opérations, etc.
Exemple :
Dimension de joint torique
39,5 × 2,5 mm : diamètre intérieur
(D) × diamètre extérieur (d)
5Les dimensions et les numéros de référence des composants sont fournis pour les éléments fixations nécessitant un couple de serrage déterminé :
Exemple :
Dimension de boulon ou de vis
10 × 25 mm (2) : M10 (D) × 25 mm (L) (2 pièces)
6Les opérations nécessitant des informations plus détaillées (comme des outils spéciaux et des spécifications techniques) sont décrites de façon séquentielle.
LEITFADEN ZUR BENUTZUNG DER ANLEITUNG
1Zur Erkennung von Teilen und zur Erläuterung von Arbeitsabläufen stehen vor jedem Abschnitt, in dem es um die Zerlegung und den Zusammenbau von Teilen geht, Darstellungen in aufgelösten Einzelteilen.
2Die Reihenfolge der Arbeitsschritte laut den Darstellungen in Einzelteilen ist mit Zahlen angegeben. Eine umkreiste Zahl zeigt eine Zerlegung an.
3Zu schmierende oder auszuwechselnde Teile werden durch Symbole angezeigt (siehe „SYMBOLE“).
4Eine Tabelle mit Anweisungen, in der die Reihenfolge der Arbeitsschritte, die Bezeichnungen der Teile, Anmerkungen zu den Arbeitsschritten usw. erwähnt werden, ist jeder Darstellung in aufgelösten Einzelteilen hinzugefügt.
Beispiel:
O-Ring-Größe: 39,5 × 2,5 mm: Innendurchmesser (D) × Ring
durchmesser (d)
5Bei Befestigungsteilen, die mit auf ein bestimmtes Moment angezogen werden müssen, sind die Abmessungen und die Zahl der erforderlichen Teile angegeben.
Beispiel:
Bolzenoder Schraubengröße: 10 × 25 mm (2) : M10(D) × 25
mm (L) (2 Stück)
6Arbeiten, die einer ausführlicheren Information bedürfen (z.B. Spezialwerkzeug und technische Angaben), werden nachstehend beschrieben.
COMO USAR ESTE MANUAL
1Para contribuir a identificar las piezas y aclarar las operaciones correspondientes a los distintos procedimientos, se incluyen diagramas de despiece al principio de cada sección de desmontaje y montaje.
2Los números que figuran en el diagrama de despiece están en el orden en que se hacen los trabajos. Un número rodeado por un círculo indica una operación de desmontaje.
3Los símbolos indican piezas que hay que lubricar o sustituir (vea “SIMBOLOS”).
4El diagrama de despiece va acompañado de una tabla de instrucciones de trabajo en la que figura el orden de éstos, nombres de las piezas, notas sobre los trabajos, etc.
Ejemplo:
Tamaño de junta tórica
39,5 × 2,5 mm: Diámetro interior
(D)× anchura de la corona (d)
5Los elementos de unión que requieren pares de apriete van acompañados de las cifras de dimensiones y la cantidad de piezas.
Ejemplo:
Tamaño de perno o tornillo
10 × 25 mm (2) : M10(D)× 25 mm
(L) (2 piezas)
6Los trabajos que requieran más información (como la relativa a herramientas especiales y datos técnicos) se describen en secuencia.
E
1 |
2 |
|
GEN |
SPEC |
|
INFO |
||
|
||
3 |
4 |
|
INSP |
FUEL |
|
ADJ |
||
|
||
5 |
6 |
|
POWR |
LOWR |
|
7 |
8 |
|
BRKT |
ELEC |
|
9 |
0 |
|
TRBL |
|
|
ANLS |
|
|
q |
w |
|
e |
r |
|
t |
y |
|
u |
i |
|
o |
p |
|
a |
s |
|
271 |
|
|
d |
f |
A50001-1-4
SYMBOLS
Symbols 1 to 9 are designed as thumbtabs to indicate the content of a chapter.
1 General information
2 Specifications
3 Periodic inspection and adjustment
4 Fuel system
5 Power unit
6 Lower unit
7 Bracket unit
8 Electrical system
9 Trouble-analysis
Symbols 0 to t indicate specific data:
0 Special tool
q Specified liquid
w Specified engine speed e Specified torque
r Specified measurement
tSpecified electrical value
[Resistance (Ω ), Voltage (V), Electric current (A)]
Symbol y to o in an exploded diagram indicate the grade of lubricant and location of the lubrication point:
y Apply Yamaha 4-stroke outboard motor oil u Apply molybdenum disulfide oil
iApply water resistant grease (Yamaha grease A, Yamaha marine grease)
o Apply molybdenum disulfide grease
Symbols p to f in an exploded diagram indicate the grade of sealing or locking agent, and the location of the application point:
p Apply Gasket Maker®
a Apply LOCTITE® No. 271 (Red LOCTITE) s Apply LOCTITE® No. 242 (Blue LOCTITE) d Apply LOCTITE® No. 572
f Apply Silicon sealant
NOTE:
In this manual, the above symbols may not be used in every case.
F |
D |
ES |
SYMBOLES
Les symboles 1 à 9 sont représentés sur les onglets et renseignent sur le contenu des différents chapitres :
1 Informations générales
2 Spécifications
3 Inspection périodique et réglage
4 Circuit d’alimentation
5 Moteur
6 Boîtier d’hélice
7 Support
8 Circuit électrique
9 Dépannage
Les symboles 0 à t apportent certaines précisions :
0 Outil préconisé q Liquide préconisé
w Régime moteur préconisé e Couple spécifié
r Mesure spécifiée
tValeur électrique spécifiée [Résistance (Ω ), tension (V), intensité (A)]
Les symboles y à o des vues éclatées donnent la qualité de lubrifiant à employer et les points de graissage :
y Huile pour moteur hors-bord 4 temps Yamaha
uAppliquez de la huile au bisulfure de molybdène
iGraisse hydrofuge (graisse marine Yamaha A, graisse marine Yamaha)
oAppliquez de la graisse au bisulfure de molybdène
Les symboles p à f des vues éclatées indiquent la qualité des agents d’étanchéité ou de blocage à employer ainsi que les points d’application :
p Liquide d’étanchéité Gasket Maker(R) a Agent bloquant LOCTITE(R) n° 271
(LOCTITE rouge)
s Agent bloquant LOCTITE(R) n° 242 (LOCTITE bleu)
d Agent bloquant LOCTITE(R) n° 572 f Produit d’étanchéité à base de silicone
N.B. :
Il est possible que certains des symboles ci-dessus ne soient pas utilisés le présent manuel.
SYMBOLE
Die Symbole 1 bis 9 sind als Daumenindex gedacht, die den Inhalt eines Kapitels anzeigen.
1 Allgemeine Informationen
2 Spezifikationen
3Periodische Inspektion und Einstellung
4 |
Kraftstoffanlage |
5 |
Antriebseinheit |
6 |
Unterwasserteil |
7 |
Motoraufhängung |
8 |
Elektrik |
9 |
Störungssuche |
Die Symbole 0 bis t weisen auf spezifische Daten und Erfordernisse hin:
0 Spezialwerkzeug
q Spezielle Flüssigkeit
w Spezielle Motordrehzahl
e Spezielles Anzugsmoment
r Spezielles Maß
tSpezieller elektrischer Wert [Widerstand (Ω ), Spannung (V), Stromstärke (A)]
Die Symbole y bis o in einer Darstellung in aufgelösten Einzelteilen weisen auf den Schmiermittelgrad und Schmierstellen hin:
y Yamaha-Viertakt-Außenbordmotoröl benutzen
u Molybden-Disulfid-Öl auftragen.
iWasserbeständiges Fett (YamahaSchmierfett A, Yamaha-Marinefett) benutzen
o Molybden-Disulfid-Fett auftragen.
Die Symbole p bis f in einer Darstellung in aufgelösten Einzelteilen weisen auf den Grad eines Dichtungsoder Sicherungsmittels sowie auf die Anbringungsstelle hin:
p Gasketmaker® auftragen
a LOCTITE® Nr. 271 (rot) auftragen s LOCTITE® Nr. 242 (blau) auftragen d LOCTITE® Nr. 572 auftragen
f Silikondichtungsmittel auftragen
HINWEIS:
In diesem Handbuch können die obenstehenden Symbole nicht in jedem Fall benutzt werden.
SIMBOLOS
Los símbolos 1 a 9 están concebidos como pestañas para indicar el contenido de un capítulo.
1 Información general
2 Especificaciones
3 Inspección periódica y ajuste
4 Sistema de combustible
5 Grupo motor
6 Unidad inferior
7 Unidad de soporte
8 Sistema eléctrico
9 Localización de averías
Los símbolos 0 a t indican datos especificados:
0 Herramienta especial q Líquido especificado
w Velocidad especificada del motor e Pares especificados
r Medidas especificadas
tValor eléctrico especificado [Resistencia (Ω ), tensión (V), corriente eléctrica (A)]
Los símbolos y a o en un diagrama de despiece indican el grado de lubricante y el sitio del punto de lubricación:
yAplique aceite Yamaha de motor fuera borda de 4 tiempos
u Aplicar aceite de bisulfuro de molibdeno i Aplique grasa resistente al agua (grasa
Yamaha A, grasa marina Yamaha)
o Aplicar grasa de bisulfuro de molibdeno
Los símbolos p a f en un diagrama de despiece indican el grado de agente sellante o de bloqueo y el sitio del punto de aplicación:
p Aplique Gasket Maker®
aAplique LOCTITE® nº 271 (LOCTITE rojo)
sAplique LOCTITE® nº 242 (LOCTITE azul)
d Aplique LOCTITE® nº 572 f Aplique sellante de silicona
NOTA:
En este manual, pueden no utilizarse en todos los casos los símbolos anteriores.
E
A30000-0
GENERAL INFORMATION
SPECIFICATION
PERIODIC INSPECTION AND
ADJUSTMENT
FUEL SYSTEM
POWER UNIT
LOWER UNIT
BRACKET UNIT
ELECTRICAL SYSTEM
TROUBLE-ANALYSYS
F |
D |
ES |
TABLE DES MATIERES
INFORMATIONS GENERALES
SPECIFICATIONS
INSPECTION PERIODIQUE ET REGLAGE
CIRCUIT D’ALIMENTATION
MOTEUR
BOITIER D’HELICE
SUPPORT
CIRCUIT ELECTRIQUE
DEPANNAGE
INHALT INDICE
ALLGEMEINE |
|
INFORMACION |
|
ANGABEN |
|
GENERAL |
GEN |
|
|
|
INFO |
|
|
|
|
TECHNISCHE |
|
ESPECIFICACIONES |
|
DATEN |
|
SPEC |
|
|
|
||
|
|
|
|
|
|
|
|
REGELMÄSSIGE WARTUNG UND EINSTELLUNGEN
KRAFTSTOFFANLAGE
STROMVER-
SORGUNG
UNTERER TEIL
INSPECCION
Y AJUSTE
PERIODICOS INSP
ADJ
SISTEMA DE
COMBUSTIBLE
FUEL
MOTOR
POWR
UNIDAD INFERIOR
LOWR
HALTERUNGSRAH- |
|
UNIDAD DE |
|
||||
MEN |
|
SOPORTE |
BRKT |
||||
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ELEKTROANLAGE |
|
SISTEMA |
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
||||
|
ELECTRICO |
ELEC |
|||||
|
|
||||||
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PROBLEMLÖSUN- |
|
DIAGNOSTICO |
|
||||
GEN |
|
DE PROBLEMAS |
TRBL |
||||
|
|
|
ANLS |
1
2
3
4
5
6
7
8
9
GEN
INFO
CHAPTER 1
E
IDENTIFICATION ........................................................................................... |
1-1 |
SERIAL NUMBER .................................................................................... |
1-1 |
STARTING SERIAL NUMBERS ............................................................... |
1-1 |
SAFETY WHILE WORKING........................................................................... |
1-2 |
FIRE PREVENTION .................................................................................. |
1-2 |
VENTILATION .......................................................................................... |
1-2 |
SELF-PROTECTION ................................................................................. |
1-2 |
OILS, GREASES AND SEALING FLUIDS ............................................... |
1-2 |
GOOD WORKING PRACTICES ............................................................... |
1-3 |
DISASSEMBLY AND ASSEMBLY ........................................................... |
1-4 |
SPECIAL TOOLS............................................................................................ |
1-5 |
MEASURING............................................................................................ |
1-5 |
REMOVAL AND INSTALLATION............................................................. |
1-7 |
GENERAL TOOL............................................................................................ |
1-9 |
F D ES
CHAPITRE 1 |
|
KAPITEL 1 |
|
CAPITULO 1 |
|
INFORMATIONS |
|
ALLGEMEINE |
|
INFORMACION |
|
GENERALES |
|
ANGABEN |
|
GENERAL |
|
IDENTIFICATION ..................................... |
1-1 |
KENNUMMERN ......................................... |
1-1 |
IDENTIFICACION..................................... |
1-1 |
NUMERO DE SERIE ............................... |
1-1 |
SERIENNUMMER .................................. |
1-1 |
NUMERO DE SERIE ............................... |
1-1 |
DEBUT DE NUMEROS DE SERIE ........ |
1-1 |
ANFANGSNUMMERN DER SERIE ....... |
1-1 |
NUMEROS INICIALES DE SERIE ........ |
1-1 |
MESURES DE SECURITE ........................ |
1-2 |
SICHERHEITSMASSNAHMEN .................. |
1-2 |
SEGURIDAD EN EL TRABAJO............... |
1-2 |
CONTRE LES INCENDIES..................... |
1-2 |
BRANDSCHUTZ..................................... |
1-2 |
PREVENCION DE INCENDIOS............. |
1-2 |
AERATION............................................... |
1-2 |
BELÜFTUNG .......................................... |
1-2 |
VENTILACION........................................ |
1-2 |
PROTECTION .......................................... |
1-2 |
SELBSTSCHUTZ .................................... |
1-2 |
AUTOPROTECCION............................... |
1-2 |
HUILES, GRAISSES ET |
|
ÖLE, SCHMIERSTOFFE UND |
|
ACEITES, GRASAS Y LIQUIDOS |
|
LIQUIDES D’ETANCHEITE................. |
1-2 |
DICHTUNGSMITTEL............................ |
1-2 |
OBTURANTES ...................................... |
1-2 |
NOTES SUR L’OUTILLAGE ET |
|
RICHTIGE |
|
PROCEDIMIENTOS DE TRABAJO |
|
LES PIECES .......................................... |
1-3 |
ARBEITSGEWOHNHEITEN ................. |
1-3 |
CORRECTOS ......................................... |
1-3 |
DEMONTAGE ET REMONTAGE .......... |
1-4 |
DEMONTAGE UND MONTAGE ............ |
1-4 |
DESMONTAJE Y MONTAJE .................. |
1-4 |
OUTILLAGE SPECIAL............................. |
1-5 |
SPEZIALWERKZEUGE................................ |
1-5 |
HERRAMIENTAS ESPECIALES............. |
1-5 |
MESURAGE............................................. |
1-5 |
MESSEN................................................. |
1-5 |
MEDICION............................................... |
1-5 |
DEPOSE ET INSTALLATION ................ |
1-7 |
AUSBAU UND EINBAU......................... |
1-7 |
RETIRAD E INSTALACION .................. |
1-7 |
OUTILLAGE GENERAL .......................... |
1-9 |
ALLGEMEINES WERKZEUG ..................... |
1-9 |
HERRAMIENTA DE USO GENERAL .... |
1-9 |
1
2
3
4
5
6
7
8
9
GEN INFO
IDENTIFICATION |
E |
|
|
|
A60001-1 |
|
3 |
1 |
|
|
4 |
2 |
YAMAHA MOTOR CO., LTD. |
|
MADE IN JAPAN |
|
|
|
|
|
|
PAYS D' ORIGINE JAPON |
IDENTIFICATION
SERIAL NUMBER
The outboard motor's serial number is stamped on a label which is attached to the port side of the clamp bracket.
NOTE:
For USA model:
As an antitheft measure, a special label on which the outboard motor’s serial number is stamped is bonded to the port side of the clamp bracket. The label is specially treated so that peeling it off causes cracks across the serial number.
1 Model name
2 Approved model code
3 Transom height
4 Serial number
STARTING SERIAL NUMBERS
The starting serial number blocks are as follows:
Model name |
Approved |
Starting |
||
|
USA/ |
serial |
||
Worldwide |
model code |
|||
CANADA |
number |
|||
|
||||
F15AMH |
F15MSHX |
66M |
S: 001432~ |
|
F15MLHX |
L: 300964~ |
|||
|
|
|||
F15AEH |
F15ESHX |
66M |
S: 200590~ |
|
F15ELHX |
L: 500755~ |
|||
|
|
|||
F15AE |
— |
66M |
S: 100302~ |
|
L: 400316~ |
||||
|
|
|
||
F9.9CMH |
— |
66N |
S: 000128~ |
|
L: 300319~ |
||||
|
|
|
||
F9.9CEH |
— |
66N |
S: 200101~ |
|
L: 500268~ |
||||
|
|
|
||
F9.9CE |
— |
66N |
S: 100106~ |
|
L: 400121~ |
||||
|
|
|
||
FT9.9DMH |
— |
66R |
S: 000101~ |
|
L: 200101~ |
||||
|
|
|
X: 500101~ |
|
FT9.9DEH |
— |
66R |
L: 300101~ |
|
X: 600101~ |
||||
|
|
|
||
FT9.9DE |
— |
66R |
S: 100101~ |
|
L: 400101~ |
||||
|
|
|
X: 700101~ |
1-1
GEN |
IDENTIFICATION |
F |
|
KENNUMMERN |
|
D |
|
INFO |
IDENTIFICACION |
ES |
|
IDENTIFICATION |
KENNUMMERN |
IDENTIFICACION |
NUMERO DE SERIE
Le numéro de série du moteur est estampillé sur l’étiquette apposée du côté bâbord du support de bridage.
SERIENNUMMER
Die Seriennummer des Außenbordmotors befindet sich auf dem Aufkleber auf der Steuerbordseite der Spannklemme.
NUMERO DE SERIE
El número de serie del motor fuera borda aparece estampado en la etiqueta fijada al lado de babor de la abrazadera de sujeción.
N.B.:
Modèle pour les E.-U.
Le numéro de série du moteur figure sur une étiquette spéciale antivol qui est apposée au côté bâbord.
Cette étiquette est conçue de sorte qu’elle se fendille à l’endroit du numéro de série quand on tente de
la décoller.
1 Nom du modèle
2 N° de modèle approuvé
3 Hauteur de barre d’arcasse
4 Numéro de série
DEBUT DE NUMEROS DE SERIE
Les blocs de début de numéros de série sont les suivants:
Modèle |
N° de |
DEBUT DE |
||
|
E.-U./ |
N° approuvé |
||
Monde |
modèle |
|||
CANADA |
DE SERIE |
|||
|
||||
|
|
|
|
|
F15 |
F15MSHX |
66M |
S: 001432~ |
|
AMH |
F15MLHX |
L: 300964~ |
||
|
||||
|
|
|
|
|
F15 |
F15ESHX |
66M |
S: 200590~ |
|
|
|
|
||
AEH |
F15ELHX |
L: 500755~ |
||
|
||||
F15 |
— |
66M |
S: 100302~ |
|
|
|
|||
AE |
L: 400316~ |
|||
|
|
|||
|
|
|
|
|
F9.9 |
— |
66N |
S:000128~ |
|
CMH |
L:300319~ |
|||
|
|
|||
|
|
|
|
|
F9.9 |
— |
66N |
S:200101~ |
|
|
|
|||
CEH |
L:500268~ |
|||
|
|
|||
F9.9 |
— |
66N |
S:100106~ |
|
|
|
|||
CE |
L:400121~ |
|||
|
|
|||
|
|
|
|
|
FT9.9 |
|
|
S:000101~ |
|
— |
66R |
L:200101~ |
||
DMH |
||||
|
|
|
||
|
|
X:500101~ |
||
|
|
|
||
|
|
|
|
|
FT9.9 |
— |
66R |
L:300101~ |
|
DEH |
X:600101~ |
|||
|
|
|||
|
|
|
|
|
FT9.9 |
|
|
S:100101~ |
|
|
|
|
||
— |
66R |
L:400101~ |
||
DE |
||||
|
|
X:700101~ |
||
|
|
|
||
|
|
|
|
HINWEIS:
Für USA-MODELLE
Zur Diebstahlsicherung ist ein spezielles Etikett mit der eingestanzten Seriennummer des Außenbordmotors auf die Backbordseite geklebt. Das Etikett ist spezialbehandelt, so daß bei der Ablösung Risse an der Seriennummer entstehen.
1 |
Modellbezeichnung |
2 |
Zugelassene Modellnummer |
3 |
Spiegelhöhe |
4 |
Seriennummer |
ANFANGSNUMMERN DER SERIE
Die Anfangsnummern |
der Serien |
|||
sind wie folgt: |
|
|
||
|
|
|
|
|
Modell |
Zugela- |
Anfangsnu |
||
Weilt |
USA/ |
mmer der |
||
weit |
KANADA |
ssene |
Serie |
|
|
|
|
|
|
F15 |
F15MSHX |
66M |
S: 001432~ |
|
AMH |
F15MLHX |
L: 300964~ |
||
|
||||
F15 |
F15ESHX |
66M |
S: 200590~ |
|
AEH |
F15ELHX |
L: 500755~ |
||
|
||||
F15 |
— |
66M |
S: 100302~ |
|
AE |
L: 400316~ |
|||
|
|
|||
F9.9 |
— |
66N |
S:000128~ |
|
CMH |
L:300319~ |
|||
|
|
|||
F9.9 |
— |
66N |
S:200101~ |
|
CEH |
L:500268~ |
|||
|
|
|||
F9.9 |
— |
66N |
S:100106~ |
|
CE |
L:400121~ |
|||
|
|
|||
FT9.9 |
|
|
S:000101~ |
|
— |
66R |
L:200101~ |
||
DMH |
||||
|
|
X:500101~ |
||
|
|
|
||
FT9.9 |
— |
66R |
L:300101~ |
|
DEH |
X:600101~ |
|||
|
|
|||
FT9.9 |
|
|
S:100101~ |
|
— |
66R |
L:400101~ |
||
DE |
||||
|
|
X:700101~ |
||
|
|
|
||
|
|
|
|
NOTA:
Para el modelo para EE. UU.
Como medida antirrobo, al lado de babor del soporte de abrazadera hay fijada una etiqueta especial en la que aparece estampado el número de serie del motor fuera de borda. La etiqueta se ha sometido a un tratamiento especial de forma que al arrancarla se agriete el número de serie.
1 Nombre de modelo
2 N.° de modelo aprobado
3 Altura del peto de popa
4 Número de serie
NUMEROS INICIALES DE SERIE
Los bloques de números iniciales de serie son los siguientes:
Modelo |
N° de |
Número de |
||
Todo los |
EE.UU./ |
serie |
||
modelo |
||||
países |
CANADA |
Aprobado |
||
|
||||
|
|
|
|
|
F15 |
F15MSHX |
66M |
S: 001432~ |
|
AMH |
F15MLHX |
L: 300964~ |
||
|
||||
|
|
|
|
|
F15 |
F15ESHX |
66M |
S: 200590~ |
|
|
|
|
||
AEH |
F15ELHX |
L: 500755~ |
||
|
||||
F15 |
— |
66M |
S: 100302~ |
|
AE |
|
|||
L: 400316~ |
||||
|
|
|||
|
|
|
|
|
F9.9 |
— |
66N |
S:000128~ |
|
CMH |
L:300319~ |
|||
|
|
|||
|
|
|
|
|
F9.9 |
— |
66N |
S:200101~ |
|
CEH |
|
|||
L:500268~ |
||||
|
|
|||
F9.9 |
— |
66N |
S:100106~ |
|
CE |
|
|||
L:400121~ |
||||
|
|
|||
|
|
|
|
|
FT9.9 |
|
|
S:000101~ |
|
— |
66R |
L:200101~ |
||
DMH |
||||
|
|
|
||
|
|
X:500101~ |
||
|
|
|
||
|
|
|
|
|
FT9.9 |
— |
66R |
L:300101~ |
|
DEH |
X:600101~ |
|||
|
|
|||
|
|
|
|
|
FT9.9 |
|
|
S:100101~ |
|
|
|
|
||
— |
66R |
L:400101~ |
||
DE |
||||
|
|
X:700101~ |
||
|
|
|
||
|
|
|
|
1-1
GEN INFO
SAFETY WHILE WORKING |
E |
SAFETY WHILE WORKING
YAMAHA OIL
The procedures given in this manual are those recommended by Yamaha to be followed by Yamaha dealers and their mechanics.
FIRE PREVENTION
Gasoline (petrol) is highly flammable. Petroleum vapor is explosive if ignited.
Do not smoke while handling gasoline and keep it away from heat, sparks and open flames.
VENTILATION
Petroleum vapor is heavier than air and is deadly if inhaled in large quantities. Engine exhaust gases are harmful to breathe. When test-running an engine indoors, maintain good ventilation.
SELF-PROTECTION
Protect your eyes with suitable safety glasses or safety goggles, when grriding or when doing any operation which may cause particles to fly off. Protect hands and feet by wearing safety gloves or protective shoes if appropriate to the work you are doing.
OILS, GREASES AND SEALING FLUIDS
Use only genuine Yamaha oils, greases and sealing fluids or those recommended by Yamaha.
1-2
GEN INFO
MESURES DE SECURITE |
F |
SICHERHEITSMASSNAHMEN |
D |
SEGURIDAD EN EL TRABAJO |
ES |
MESURES DE SECURITE
Les opérations décrites dans ce manuel sont recommandées par Yamaha et doivent être suivies par les concessionnaires Yamaha et leurs mécaniciens.
CONTRE LES INCENDIES
SICHERHEITSMASSNAHMEN
Die in diesem Handbuch angegebenen Maßnahmen sind von den Yamaha-Händlern und ihren Mechanikern zu beachten.
SEGURIDAD EN EL TRABAJO
Los procedimientos incluidos en este manual son los que Yamaha recomienda a sus concesionarios y
mecánicos.
L’essence est un produit très inflammable.
Les vapeurs d’essence sont explosives lorsqu’elle sont enflammées. Ne pas fumer lors de la manipulation d’essence.
La maintenir à l’écart de la chaleur, des étincelles et des flammes.
AERATION
Les vapeurs d’essence sont plus lourdes que l’air; inhalées en grande quantité, elles sont mortelles. Les gaz d’échappement du moteur sont toxiques.
Lors d’essais de fonctionnement d’un moteur en intérieur, s’assurer que l’endroit est bien aéré.
PROTECTION
Se protéger les yeux avec des lunettes ou un masque de sécurité appropriés lors de l’utilisation d’air comprimé ou lors de toute opération durant laquelle des particules risquent d’être projetées. Si nécessaire, se protéger également les mains et les pieds à l’aide gants et des chaussures de protection.
HUILES, GRAISSES ET LIQUIDES D’ETANCHEITE
N’utiliser que les huiles, graisses et liquides d’étanchéité Yamaha ou recommandés par Yamaha.
BRANDSCHUTZ
Kraftstoff (Petroleum, Benzin) ist leicht brennbar.
Benzindämpfe sind hochexplosiv. Beim Umgang mit Kraftstoff nicht rauchen sowie Funken und offenes Feuer vermeiden.
BELÜFTUNG
Benzindämpfe sind schwerer als Luft. Bei Einatmung großer Mengen besteht Lebensgefahr. Motorabgase sind gesundheitsschädlich und bei längerem Einatmen lebensgefährlich. Beim Probelauf eines Motors in geschlossenen Räumen für ausreichende Belüftung sorgen.
SELBSTSCHUTZ
Beim Arbeiten mit Druckluft, bei Schleifarbeiten oder bei Spritzgefahr eine geeignete Sicherheitsoder Schutzbrille tragen. Füße durch Sicherheitsschuhe schützen. Wenn erforderlich, die Hände mit Schutzhandschuhen schützen.
ÖLE, SCHMIERSTOFFE UND DICHTUNGSMITTEL
Nur von Yamaha empfohlene Öle, Schmierstoffe und Dichtungsmittel verwenden.
PREVENCION DE INCENDIOS
La gasolina (petróleo) es altamente inflamable.
El vapor de petróleo es explosivo si se enciende.
No fume mientras manipula gasolina y manténgala alejada del calor, chipas y llamas.
VENTILACION
El vapor de petróleo es más pesado que el aire y si se inhala en grandes cantidades puede provocar asfixia. Los gases de escape del motor son dañinos. Cuando compruebe el funcionamiento de un motor en un local cerrado, mantenga el lugar bien ventilado.
AUTOPROTECCION
Proteja sus ojos con gafas de seguridad cuando utilice aire comprimido, cuando esmerile o cuando realice cualquier operación que provoque el desprendimiento de partículas. Proteja sus manos y pies con guantes de seguridad o zapatos fuertes apropiados para el trabajo a realizar.
ACEITES, GRASAS Y LIQUIDOS OBTURANTES
Utilice siempre aceites, grasas y líquidos obturantes genuinos Yamaha, u otros recomendados por Yamaha.
1-2
GEN INFO
SAFETY WHILE WORKING |
E |
Under normal conditions of use, there should be no hazards from the use of the lubricants mentioned in this manual, but safety is all-important, and by adopting good safety practices, any risk is minimized. A summary of the most important precautions is as follows:
1.While working, maintain good standards of personal and industrial hygiene.
2.Clothing which has become contaminated with lubricants should be changed as soon as practicable, and laundered before further use.
3.Avoid skin contact with lubricants; do not, for example, place a soiled wipingrag in your pocket.
4.Hands and any other part of the body which have been in contact with lubricants or lubricant-contaminated clothing, should be thoroughly washed with hot water and soap as soon as practicable.
5.To protect the skin, the application of a suitable barrier cream to the hands before working is recommended.
6.A supply of clean lint-free cloths should be available for wiping purposes.
GOOD WORKING PRACTICES
1.The right tools
Use the recommended special tools to protect parts from damage. Use the
right tool in the right manner — do not improvise.
2. Tightening torque
Follow the tightening torque instructions. When tightening bolts, nuts and screws, tighten the large sizes first, and tighten inner-positioned fixings before outer-positioned ones.
1-3
GEN INFO
MESURES DE SECURITE |
F |
SICHERHEITSMASSNAHMEN |
D |
SEGURIDAD EN EL TRABAJO |
ES |
Dans des conditions normales d’utilisation, il ne devrait pas y avoir de dangers liés à l’utilisation des lubrifiants spécifiés dans ce manuel. Il convient cependant de prendre toutes les précautions de sécurité requises pour en minimiser les risques.
Les principales précautions à prendre peuvent se résumer de la façon suivante:
1.En travaillant, observez les conditions d’hygiène personnelle et industrielle qui s’imposent.
2.Les vêtements contaminés par des lubrifiants doivent être changés le plus rapidement possible et lessivés avant toute réutilisation.
3.Evitez le contact des lubrifiants sur la peau; ainsi, ne mettez pas en poche des chiffons souillés.
4.Si les mains ou toute autre partie du corps ont été en contact avec des lubrifiants ou des vêtements contaminés de lubrifiant, lavez-les dès que possible à l’eau chaude et au savon.
5.Pour vous protéger la peau, nous vous conseillons d’appliquer sur les mains une crème écran appropriée avant de commencer à travailler.
6.Prévoyez toujours une réserve suffisante de chiffons propres et non pelucheux.
NOTE SUR L’OUTILLAGE ET LES PIECES
1.Outillage adéquat
Utilisez l’outillage spécial préconisé afin de protéger les pièces contre tout dommage. Utilisez l’outillage adéquat et de la façon prescrite. N’improvisez en aucune circonstance.
2.Couple de serrage
Respectez les couples de serrage spécifiés. Lorsque vous serrez des boulons, des écrous et des vis, commencez par serrer ceux dont le diamètre est le plus important en allant du centre vers l’extérieur.
Unter normalen Betriebsbedingungen entstehen durch die Verwendung der in diesem Handbuch genannten Schmierstoffe keine Gefahren. Sicherheit ist jedoch oberstes Gebot. Durch Beachtung der Sicherheitsmaßnahmen werden jegliche Gefahren auf ein Minimum begrenzt.
Nachstehend folgt eine Übersicht der wichtigsten Sicherheitsmaßnahmen:
1.Während der Arbeit immer für saubere, gut sitzende Arbeitskleidung und einen sauberen Arbeitsplatz sorgen.
2.Durch Schmiermittel verschmutzte Kleidung so bald wie möglich wechseln und vor derweiteren Benutzung gründlich reinigen.
3.Schmiermittel nicht mit der Haut in Berührung bringen. Keine schmutzigen Lappen in die Tasche stekken.
4.Hände und andere Körperteile, die in Berührung mit Schmiermitteln oder durch Schmiermittel verschmutzte Kleidung gekommen sind, so bald wie möglich gründlich mit warmem Wasser und Seife reinigen.
5.Zum Schutz der Haut wird vor Arbeitsbeginn das Auftragen einer geeigneten Schutzcreme empfohlen.
6.Ein Vorrat an geeigneten Putztüchern oder saugfähigem Papier sollte stets vorhanden sein.
RICHTIGE ARBEITSGEWOHNHEITEN
1.Die richtigen Werkzeuge
Um Motorteile vor Beschädigung zu schützen, passendes Werkzeug und empfohlenes Spezialwerkzeug benutzen. Das Werkzeug in der vorgeschriebenen Art und Weise benutzen
– nicht behelfsmäßig seinem Zweck entfremden.
2.Anzugsdrehmoment
Die Anweisungen über die Anzugsdrehmomente beachten. Beim Festziehen der Schrauben und Muttern zuerst die größeren Schrauben anziehen. Danach die innenliegenden und zuletzt die außenliegenden Schrauben anziehen.
En condiciones normales de uso, el empleo de los lubricantes mencionados en este manual no debe plantear ningún riesgo, pero la seguridad es un tema de la máxima importancia, por lo que la adopción de algunas medidas de seguridad puede reducir los posibles riesgos.
A continuación se incluye un resumen de las precauciones más importantes:
1.Cuando trabaje, mantenga una higiene personal e industrial correcta.
2.La ropa contaminada con lubricante debe cambiarse tan pronto como sea posible y ser lavada antes de volver a usarla.
3.Evite el contacto de la piel con los lubricantes. Por ejemplo, no introduzca un trapo impregnado en el bolsillo.
4.Las manos y cualquier otra parte del cuerpo que haya estado en contacto con lubricantes o ropa contaminada por lubricantes deben lavarse minuciosamente con agua caliente y jabón tan pronto como sea posible.
5.Para proteger la piel, se recomienda aplicar una crema protectora apropiada en las manos antes de iniciar el trabajo.
6.Debe disponerse de paños limpios que no dejan pelusa para fines de limpieza.
PROCEDIMIENTOS DE TRABAJO CORRECTOS
1.Las herramientas correctas
Utilice las herramientas especiales aconsejadas para evitar dañar las piezas. Utilice la herramienta correcta de la manera apropiada
— no improvise.
2.Par de apriete
Siga las instrucciones relacionadas al par de apriete. Cuando apriete pernos, tuercas y tornillos, apriete en primer lugar los de mayor tamaño, y apriete los situados en la parte interior antes de apretar los situados en la parte exterior.
1-3
GEN INFO
SAFETY WHILE WORKING |
E |
3. Non-reusable items
Always use new gaskets, packings, O- rings, split-pins and circlips, etc., on reassembly.
DISASSEMBLY AND ASSEMBLY
1. Clean parts with compressed air when disassembling.
2. Oil the contact surfaces of moving parts before assembly.
3. After assembly, check that moving parts operate normally.
4. Install bearings with the manufacturer's markings on the side exposed to view, and liberally oil the bearings.
cC
Do not use compressed air to spin the bearings dry. This causes damage to the bearing surfaces.
5. When installing oil seals, apply a light coating of water-resistant grease to the outside diameter.
1-4
GEN INFO
MESURES DE SECURITE |
F |
SICHERHEITSMASSNAHMEN |
D |
SEGURIDAD EN EL TRABAJO |
ES |
3.Pièces à usage unique
Lors du remontage, toujours utiliser des joints, garnitures, joints toriques, goupilles fendues et circlips neufs.
DEMONTAGE ET REMONTAGE
1.Lors du démontage, nettoyer les pièces à l’air comprimé.
3.Nicht wiederverwendbare Teile Beim Wiedereinbau stets neue Dichtungen, O-Ringe, Splinte, Sicherungsringe usw. verwenden.
DEMONTAGE UND MONTAGE
1.Während des Ausbaus Teile mit Druckluft reinigen.
3.Elementos no reutilizables
Utilice siempre juntas, guarniciones, juntas toroidales, pasadores hendidos y retenedores nuevos cuando vuelva a montar los componentes.
DESMONTAJE Y MONTAJE
1.Limpie las piezas con aire comprimido al desmontarlas.
2.Lors du montage, huiler les surfaces de contact des pièces mobiles.
3.Après le montage, vérifier que toutes les pièces mobiles fonctionnent normalement.
4.Monter les roulements avec la marque du fabricant tournée vers l’extérieur et les huiler généreusement.
2.Kontaktflächen beweglicher Teile beim Einbau fetten.
3.Nach der Montage bewegliche Teile auf einwandfreie Funktion prüfen.
4.Lager so einsetzen, daß die Herstellerkennzeichen sichtbar sind. Lager ausreichend fetten.
2.Engrase las superficies de contacto de las piezas móviles al montarlas.
3.Tras el montaje, compruebe que las partes móviles funcionan con normalidad.
4.Instale los cojinetes con las marcas del fabricante encaradas hacia el lado que queda expuesto a la vista, y engráselos abundantemente.
fF
N’utilisez pas d’air comprimé pour sécher les roulements. Vous risquez sinon d’endommager les surfaces des roulements.
5.Lors du montage des bagues d’étanchéité, appliquer une légère couche de graisse hydrofuge sur le diamètre extérieur.
dD
Niemals Druckluft zum Trocknen der Lager benutzen, weil dadurch die Oberfläche der Lager beschädigt wird.
5.Beim Einbau der Öldichtungen diese leicht mit einem wasserbeständigen Fett einreiben.
bB
No se debe utilizar aire comprimido para secar los cojinetes, ya que se podrán dañar sus superficies.
5.Cuando instale juntas de aceite, aplique una capa de grasa hidrófuga en la circunferencia exterior.
1-4
GEN INFO
SPECIAL TOOLS |
E |
SPECIAL TOOLS
|
|
|
The use of correct special tools recom- |
||
|
|
|
mended by Yamaha will aid the work and |
||
|
|
|
enable accurate assembly and tune-up. |
||
|
|
|
Improvising and using improper tools can |
||
|
|
|
damage the equipment. |
||
|
|
|
NOTE: |
|
|
|
|
|
9For U.S.A. and Canada, use part numbers |
||
|
|
|
starting with “J-”, “YB-”, “YM-” “YU-” or |
||
|
|
||||
1 a |
b |
|
“YW-”. |
||
|
|
|
9For others, use part numbers starting with |
||
|
|
|
“90890-”. |
||
|
|
|
|
|
|
|
|
MEASURING |
|
|
|
1. |
Tachometer |
2 |
3 |
a |
P/N. YU-08036-A |
|
|
b |
90890-06760 |
|
|
2. |
Mity vac |
|
|
|
P/N. YB-35956 |
|
|
|
90890-06756 |
|
|
3. |
Leakage tester |
4 |
5 |
|
P/N. YB-03595 |
|
|
|
90890-06762 |
|
|
4. |
Pinion height gauge |
|
|
|
P/N. YB-34232 |
|
|
|
N.A. |
|
|
5. |
Digital caliper |
6 |
7 |
|
P/N. N.A. |
|
90890-06704 |
||
|
|
|
|
|
|
6. |
Shimming plate |
|
|
|
P/N. N.A. |
|
|
|
90890-06701 |
|
|
7. |
Dial gauge set |
8 |
9 |
|
P/N. YU-03097 |
|
90890-01252 |
||
|
|
|
|
|
|
8. |
Backlash indicator |
|
|
|
P/N. YB-06265 |
|
|
|
90890-06706 |
|
|
9. |
Magneto base |
0 |
|
|
P/N. YU-34481 |
|
|
90890-06705 |
|
|
|
10. Base plate |
|
|
|
|
P/N. YB-07003 |
|
|
|
90890-07003 |
1-5