TANDBERG D13922.06 User Manual

Installation Sheet

TANDBERG Edge

This box contains:

TANDBERG Edge unit TANDBERG Precision HD camera Edge unit wall mounting bracket Precision HD camera bracket Screwdriver (PH2) Rubber feet and plug

Microphone and microphone cable HD camera cables, 2 m & 5 m LAN cable ISDN cables DVI-I to DVI-I cable (for monitor connection) DVI-I to VGA adapter S-Video cable RCA to RCA cable DVI-I to VGA cable with mini-jack to stereo RCA Audio cable (for PC connection) Audio cable, RCA to 2 × RCA 2 × RCA to stereo mini-jack adapter Cable sleeve Cable ties Power supply with cables

TANDBERG Remote Control and batteries User Guide on CD Registration card

TANDBERG Precision HD Camera

The Camera must

be installed properly

by aligning the

camera on the

xing bolt and the

magnets on the

camera bracket.*

* Installation of the camera bracket with the

TANDBERG Flat Panel Display Option.

A wall mounted screen must have minimum

140 mm distance from the front of the screen

to the wall.

LAN/Ethernet

Microphone

Monitor

Power Supply

Desktop Use

Touch tonesSnapshot

Camera Pre sets

TIP If the menu is not already present, press the OK/Menu key on the remote control to open the menu. Navigate in the menu with arrow keys and OK.

Please read the user documentation for further details.

D13922.06 MARCH 2008

Using the unit out of the box

Placing the unit on a shelf

Put it on the desktop, connect cables as shown to the far right and it is ready to use.

CAUTION! Never place the unit as shown without the base

mounted!

Unscrew the base, using the enclosed screwdriver. Put the Edge codec on its back.

Turn the unit upside down and mount the rubber feet over the screws. Insert the rubber plug in the hole that held the screw just unscrewed.

Place the unit on the shelf.

1 2

3 4

Connect cables as shown to the right.

DVI-I to DVI-I

Composite

S-video

(optional)

CAUTION! Do not screw the screw back in if

the base has been removed and the bracket is not to be used. Doing so may damage the codec’s interior and will void the warranty. Use the enclosed rubber plug instead.

Rubber plug

D1392205_Edge_Installation_Sheet_Feb08.indd 1 10.03.2008 09:56:24

Installation Sheet

TANDBERG Edge

Wall Mounting

Recommended mounting

DO NOT MOUNT IT HERE!

Alternative mounting





Equipment needed:

Caution!

Remove the monitor. Make sure there

is space for all cables when the monitor is put back in place. Also make sure that the cable connections will be well hidden behind the monitor.

Recommended

Alt. 1

Alt. 2

Unscrew the base using the enclosed screwdriver.

Put the Edge codec on its back.

Bracket with screw (included).

Screwdriver to remove the base and mount the bracket (included).

Suitable screws (at least 4×15) to mount bracket on wall (not included). Each screw must be able to sustain at least 10 kg when bracket is mounted.

Screwdriver to mount bracket on wall (not included).

Decide where to mount the Edge codec.

1 2 3

5 6

7 8

Mount the Edge codec (with all the cables connected) onto the bracket using the screw of the wall bracket. Mount the monitor and camera (see instructions overleaf) back in place.

Hose (sleeve) to accommodate the cables between the codec and the monitor and camera (included).

Use screws in all four holes for mounting. Do not rely on the center hole alone.

Connect cables as shown overleaf.

D13922.06 MARCH 2008

Mount the bracket on the wall.

CAUTION! Never use other screws than the 20 mm screw already attached to the wall

bracket. Do not remove this screw. Using other screws may damage the codec’s interior and will void the warranty.

D1392205_Edge_Installation_Sheet_Feb08.indd 2 10.03.2008 09:56:30