TANDBERG Profile 42” using C20 .................................... 47
D14637.01—MARCH 2010
2
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Introduction
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Administrator guide
Chapter 1
Introduction
www.tandberg.com
D14637.01—MARCH 2010
3
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Introduction
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Administrator guide
Introduction
You may already be familiar with the administrator guides
for the Profile Series and Codec C Series. To help you
find the information you need, TANDBERG has split the
information into smaller and more accessible parts listed
on the right of this page.
The purpose of this document
The purpose of this document is to provide you with
information required to administrate your product at an
advanced level.
Disclaimers and Notices
The objective of this documentation is to provide the
reader with assistance in using and configuring the
product. The capabilities of TANDBERG products and
other manufacturers’ products change over time and
so the required configuration may be different from
that indicated here. If you have any suggestions for
changes to this document, please feed them back
to TANDBERG through your TANDBERG Authorized
Service Representative.
If you need technical suppor t, please contact your
TANDBERG Authorized Service Representative.
The specifications for the product and the information
in this Guide are subject to change at any time, without
notice, by TANDBERG. Ever y effort has been made to
supply complete and accurate information in this Guide
however, TANDBERG assumes no responsibility or
liability for any errors or inaccuracies that may appear in
this document.
TANDBERG® is a registered trademark belonging to
Tandberg ASA. Other trademarks used in this document
are the property of their respective holders.
This Guide may be reproduced in its entirety, including
all copyright and intellectual property notices, in limited
quantities in connection with the use of this product.
Except for the limited exception set forth in the previous
sentence, no part of this Guide may be reproduced,
stored in a retrieval system, or transmitted, in any
form, or by any means, electronically, mechanically, by
photocopying, or other wise, without the prior written
permission of TANDBERG.
• Getting started guide for Profile Series, Codec C Series, Quick Set C20
• User Guide for Profile Series, Codec C Series and Quick Set C20
• Administrator guide for Profiles using Codec C20 and Quick Set C20
• Administrator guide for Profiles using Codec C60 and Codec C60/C40
• Administrator guide for Profiles using Codec C90 and Codec C90
• Camera user guide for PrecisionHD 1080p/720p
• API guides for Codec C90, C60, C40
• Physical interfaces guides for Codec C90, C60, C40
• Legal and safety information for Profile Series, Codec C Series and
Quick Set C20
Download the user documentation
Go to: http://www.tandberg.com/docs
D14637.01—MARCH 2010
4
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Introduction
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Administrator guide
What’s new in this version
The information on this page describes the highlights and main
changes in the new version for the C Series line of codecs.
Software release notes
For a complete overview of the news and changes, we
recommend reading the TANDBERG TC Software Release Notes
(TC3). Go to: http://www.tandberg.com/docs
User documentation
You may already be familiar with the user guides for the Profile
Series, Codec C Series and Quick Set C20. To help you find the
information you need, TANDBERG has split the guides into smaller
and more accessible parts.
The Administrator Guide has been split into:
• Getting started guide
• Video conference room primer guide
• Camera user guide
• Administrator guide (smaller size)
• Legal and safety information
The User Guides have been merged into one guide:
• User Guide for Profile Series, Codec C Series and Quick Set
C20
The user documentation is available from our web site. Select
your product from the drop down list to see an overview of the
user documnetation for that product.
Go to: http://www.tandberg.com/docs
New feature and improvements
Configuration profiles
Enhanced usability features with Configuration Profiles. The
functionality is available from sof tkeys when you enter the
“Advanced Configuration” menu.
Today’s bookings
Systems provisioned by the TANDBERG Management System
(TMS ) can display today’s current bookings in the GUI.
Confirm selection of video output resolution
When changing the output resolution, the system will prompt you
and let you keep or cancel the selected resolution. In the event
that the monitor doesn’t support the new selected resolution, no
prompt will be shown; selection will time out and thus the system
will revert to the previous resolution.
System information, frame rate indicator
The call status will now include frame rate, thus making it easy to
see if you are sending/receiving 30 or 60 frames per second. As
this is just an indicator and not a proper frame rate counter, it will
not show accurate sent or received frame rate. However you will
be able to see if the system is now sending or receiving 60 frames
per second.
Autocomplete
When starting to type in a number in the call dialog box, it will now
provide matches from recent calls, corporate phonebook and
local contacts.
Telephone call icon
A telephone call icon will now be displayed along with the
telephone number when combined with a video call or
presentation.
Russian Input method
When Cyrillic is selected as input method, Russian can be used
as multitap. A Russian version of the remote control will be
available at the same time as the TC3.0 release.
Do Not Disturb
A proper icon will now be displayed in the lower right corner, when
do not disturb is active. And a text box reminding you that ‘Do not
disturb’ is active will be presented in the middle of the screen, if
you have no menus or presentation active.
Do not disturb can be activated by holding down the disconnect
key until the Standby dialog box appears.
New menu languages
Finnish, Traditional Chinese, Portuguese Brazilian, Polish, Danish,
Dutch
Call rate selection
The soft button to select call rate is now available from the ‘Enter
contact’ field in the call dialog box.
Improved web interface
The web interface lets you:
• Check system info
• Upgrade software and add release and option keys
• Configure the system using the advanced configuration
• Upload custom wallpaper using png format.
• Place calls and see the call status
• Upload Certificates
• Download XML files
• Download system logs
Video enhancements
Optimal Definition Profiles
Each video input can now be configured to allow different optimal
definition profiles. You can set the profile level, which tells your
system how good lighting you have in your room, and you can set
when to prefer 60 frames per second over 30 frames per second.
Overscan compensation
Support for monitor overscan compensation, where both video
and GUI will be scaled to suppor t monitors that do not support
the ability to display an image in pixel-by-pixel mode.
D14637.01—MARCH 2010
5
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Introduction
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Administrator guide
Video enhancements, continued...
New encoding and decoding resolutions
• WUXGA (1920*1200)
• In dual stream Codec C20 is limited to WXGA
Letterbox removal
The system will detect letterboxing or pillar boxing and scale the
image to fit the screen. If the system receives a 4/3 image with
letterboxing (16/9), it will scale the image to fit the entire screen.
Improved video layout control
It is now possible to configure which layout family to be used as
default in any system state. This allows for having default self view
on the second monitor for dual monitor systems.
This functionality has to be configured using the API (dataport).
Improved packet loss resilience
The packet loss concealment has been improved, which provides
noticeable better performance over previous software versions in
packet loss environments.
ClearPath (Experimental mode)
Available in TC3.0 in the Experimental menu as a technology
preview, and should only be used for demonstration purposes.
ClearPath is TANDBERG’s solution to minimize the negative
effects of packet loss in a non-optimal network.
Must be enabled from the API or GUI. See the: Experimental
Conference PacketLossResilience configuration.
Multiway
Multiway™ conferencing enables video endpoint users to
introduce a 3rd party into an existing call. It can be used in the
following situations:
• You want to add someone else to your existing call.
• You are called by a 3rd party while already in a call and you
want to include that person in the call.
Camera
With the TC3.0.0 release, the PrecisionHD 1080p camera will
automatically be upgraded to camera sof tware release ID40056.
Included in this release is:
• Ability to set DHCP to on over Visca.
• Added visca commands for changing integration time manually
between 50 and 60Hz. To be used if the camera is not able to
detect the power frequency.
D14637.01—MARCH 2010
6
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Advanced config.
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Administrator guide
System overview
TANDBERG Profile 42” using Codec C20
See the installation sheet for the TANDBERG Profile for
instructions on how to install the system.
Codec C20
• Full HD video.
• High resolution data sharing.
• Rich I/O capabilities.
PrecisionHD 1080p camera
Full HD Camera designed for visual communication with:
• 12 x optical zoom.
• Fast and precise pan, tilt and zoom.
Monitor
42” Full HD LCD, 16:9, 1080 x 1920 resolution.
Audio module
Wide band audio module supporting:
• 20 kHz AAC-LD.
• 1 echo canceller.
TANDBERG Profile 42”
Ethernet cable
PC cable
Mic cables
PrecisionHD 1080p camera
Monitor 42’’
Full HD LCD
In the base module:
• Audio amplifier ( DNAM)
• TANDBERG Codec C20
Audio amplifier
Optimized DNAM for TANDBERG Profile providing
crystal clear and natural audio.
Microphones
2 x Microphones.
Remote control
TANDBERG Remote Control TRC5, with AAA batteries.
Foot stand
Standalone, wheelbase or wall mounting foot stand.
D14637.01—MARCH 2010
Power cable
Foot stand (standalone,
wheelbase or wall mounting foot
module)
7
Remote control
with 4 batteries
2 x Microphones
with cables
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Introduction
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Administrator guide
System overview
The Quick Set C20 packs the rich user experience of larger
systems into a compact room based solution. TANDBERG Quick
Set C20 is a high definition video collaboration system that has
options for 1080p30 or 720p60 resolution, while being easy to
deploy, simple to manage and intuitive to use. The TANDBERG
Quick Set C20 is uniquely positioned to enable small scale
deployment of a first time video solution, as well as allowing
the enterprise scale an existing video conferencing solution to
hundreds of locations throughout the entire organization.
TANDBERG Quick Set C20/C20 Plus
Never before has the absolute quality of 1080p HD video been so
accessible. The Quick Set C20 represents the first time a video
solution with this quality and ease of use is available at a price
point suited for small teams and those just starting out with video.
TANDBERG Quick Set C20
The TANDBERG Quick Set C20 includes a TANDBERG Codec
C20, PrecisionHD 1080p 4X zoom camera, Performance Mic 20
and remote control. Simply add to any HD display and be ready
to meet.
TANDBERG Quick Set C20plus
The TANDBERG Quick Set C20 includes a TANDBERG Codec
C20, PrecisionHD 1080p 12X zoom camera, Performance Mic 20
and remote control. Simply add to any HD display and be ready
to meet.
Design features
• Transforms a flat panel display into a 1080p high definition
meeting space
• Simple, intuitive connections make setup as easy as
connecting a DVD player
• Quick Set C20 provides up to 1080p30 resolution with a 4x
zoom camera
• Quick Set C20Plus provides up to 1080p30 and 720p60
resolution with a 12x zoom camera
• Standards-compliant 1080p solution — compatible with
standards-based video without loss of features
• Sleek, compact design
Application features
• Share multimedia and presentations at the touch of a button
• Basic API available over IP (Telnet or SSH)
• Dual-display option available
• HD content sharing with 720p and WXGA
Performance features
• Optimal definition up to 1080p30
• H.323/SIP up to 6 Mbps
• Takes advantage of the TANDBERG Total Solution for
Management, including Multiway, recording and streaming and
firewall traversal services
D14637.01—MARCH 2010
8
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Advanced config.
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Administrator guide
Chapter 2
Advanced configuration settings
www.tandberg.com
D14637.01—MARCH 2010
9
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Advanced config.
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Administrator guide
Description of the advanced configuration settings
In the following pages you will find a complete list of the system settings which are configured from
the Advanced configuration menu. Open the Home menu on screen and go to: Settings > Advanced
> Advanced configuration. The examples shows either the default value or an example of a value.
The Audio settings
Audio SoundsAndAlerts KeyTones Mode
The system can produce a sound every time a key on the remote control is pressed.
Valuespace: <On/Off>
On: There will be a sound indicator when pressing keys on the remote control.
Off: The key tone on the remote control is switched off.
Sets the ring tone volume for an incoming call in steps of 0.5dB, from -34.5dB to 15dB.
Valuespace: <0..100>
Select a value between 1 and 100. Volume 0 = Off.
Example: Audio SoundsAndAlerts RingVolume: 50
Audio Volume
Sets the volume level on the loudspeaker output in steps of 0.5dB, from -34.5dB to 15dB.
Valuespace: <0..100>
Select a value between 1 and 100. Volume 0 = Off.
Example: Audio Volume: 70
The Camera settings
Cameras PowerLine Frequency
Applies to cameras supporting PowerLine frequency anti-flickering, i.e PrecisionHD 1080p cameras.
Valuespace: <Auto/50Hz/60Hz>
Auto: Set to Auto to enable power frequency auto detection in the camera.
50Hz, 60Hz: Set to 50Hz or 60Hz.
Example: Cameras PowerLine Frequency: Auto
Cameras Camera [1..1] Backlight
Backlight is used to compensate for lights shining directly at the camera ( usually the sun entering the
window) to avoid a too dark image from the room.
Valuespace: <On/Off>
On: Set to On to turn on the backlight compensation.
Off: Set to Off to turn the backlight compensation of f.
Example: Cameras Camera 1 Backlight: Off
Cameras Camera [1..1] Brightness Level
Define the Brightness Level for the camera. Requires the Brightness Mode to be set to manual.
Valuespace: <1..31>
Select a value between 1 and 31.
Example: Cameras Camera 1 Brightness Level: 1
Cameras Camera [1..1] Brightness Mode
Define whether to control the camera brightness manually or to have it automatically adjusted by the
system.
Valuespace: <Auto/Manual>
Auto: When set to Auto, the camera brightness is automatically set by the system.
Manual: Set to Manual to enable manual control of the camera brightness, e.g. the level of the
brightness level setting will be used for the camera.
Example: Cameras Camera 1 Brightness Mode: Auto
D14637.01—MARCH 2010
10
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Advanced config.
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
The Camera settings, cont...The Camera settings, cont...
Administrator guide
Cameras Camera [1..1] Flip
With Flip mode (vertical flip) you can flip the image upside down.
Valuespace: <Auto/On/Off>
Auto: When the camera is placed upside down the image is automatically flipped upside down. Use
this setting with cameras that can be mounted upside down, and that can auto detect that the camera
is mounted upside down.
On: When set to On the video on screen is flipped. This setting is used with cameras that can be
mounted upside down, but cannot auto detect that the camera is mounted upside down.
Off: Set to Off to display the video on screen the normal way.
Example: Cameras Camera 1 Flip: Off
Cameras Camera [1..1] Focus Mode
Determines whether the camera should be in auto focus or manual focus mode.
Valuespace: <Auto/Manual>
Auto: When set to Auto the focus will be updated throughout the call. When moving the camera, the
system will use auto focus for a few seconds to set the right focus of the new camera position. After a
few seconds auto focus is turned off to prevent continuous focus adjustments of the camera.
Manual: If set to Manual the focus is adjusted manually.
Example: Cameras Camera 1 Focus Mode: Auto
Cameras Camera [1..1] Gamma Level
By setting the Gamma Level you can select which gamma correction table to use. This setting may be
useful in difficult lighting conditions, where changes to the brightness setting does not provide satisfactory
results. Requires the Gamma Mode to be set to Manual.
Valuespace: <0..7>
Select a value between 0 and 7.
Example: Cameras Camera 1 Gamm a Level: 0
Cameras Camera [1..1] IrSensor
The Camera IR setting determines whether the infrared receiver at the camera should be enabled or not.
The IR sensor LED is located in the front of the camera and flickers when the IR sensor is activated from
the remote control.
Valuespace: <On/Off>
On: Set to On to enable the IR sensor on the camera.
Off: Set to Off to disable the IR sensor on the camera.
Example: Cameras Camera 1 IrSensor: On
Cameras Camera [1..1] Mirror
With Mirror mode ( horizontal flip) you can mirror the image on screen.
Valuespace: <Auto/On/Off>
Auto: When the camera is placed upside down the image is automatically mirrored. Use this setting
with cameras that can be mounted upside down, and that can auto detect that the camera is mounted
upside down.
On: Set to On to see the selfview in mirror mode, e.g. the selfview is reversed and the experience of
selfview is as seeing yourself in a mirror.
Off: Set to Off to see the selfview in normal mode, e.g. the experience of selfview is as seeing yourself
as other people see you.
Example: Cameras Camera 1 Mirror: Off
Cameras Camera [1..1] Whitebalance Level
Specify which camera to control. Define the Whitebalance Level for the camera. Requires the
Whitebalance Mode to be set to manual.
Valuespace: <1..16>
Select a value between 1 and 16.
Example: Cameras Camera 1 Whitebalance Level: 1
Cameras Camera [1..1] Gamma Mode
Applies to cameras which supports Gamma mode. The Gamma Mode setting enables for gamma
corrections. Gamma describes the nonlinear relationship bet ween image pixels and monitor brightness.
The TANDBERG PrecisionHD 720p camera supports Gamma Mode. Not supported on TANDBERG
PrecisionHD 1080p camera.
Valuespace: <Auto/Manual>
Auto: Auto is the default and the recommended setting.
Manual: In severe light conditions, you may switch mode to manual and specif y explicitly which gamma
table to use by setting the Gamma Level.
Example: Cameras Camera 1 Gamm a Mode: Auto
D14637.01—MARCH 2010
Cameras Camera [1..1] Whitebalance Mode
Define whether to control the camera whitebalance manually or to have it automatically adjusted by the
system.
Valuespace: <Auto/Manual>
Auto: When set to Auto, the camera will continuously adjust the whitebalance depending on the
camera view.
Manual: Set to Manual to enable manual control of the camera whitebalance, e.g. the level of the
whitebalance level setting will be used for the camera.
Example: Cameras Camera 1 Whitebalance Mode: auto
11
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Advanced config.
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Administrator guide
The Camera settings, cont...
Cameras Camera [1..1] DHCP
Applies to cameras which supports DHCP, i.e the PrecsisionHD 1080p cameras. The camera must be
connected to a LAN. When set, the command enables support for SW upgrade of daisy chained cameras.
It will enable the camera’s DHCP function and force start of MAC and IP address retrieval. Remember to
reset the DHCP when the camera is no longer connected to a L AN.
Valuespace: <On/Off>
On: Set to On to enable DHCP in the camera. The camera is automatically re-booted. After re-boot the
DHCP is started and the IP address will be retrieved. Run the commnand “xStatus Camera” for result.
Off: Set to Off will disable DHCP in the camera. NOTE: When camera is not connected to a LAN, this
setting should be applied.
Example: Cameras Camera 1 DHCP: Off
The Conference settings
Conference [1..1] AutoAnswer Delay
Defines how long (in seconds) an incoming call has to wait before it is answered automatically by the
system. Requires the Autoanswer Mode to be enabled.
Valuespace: <0..50>
Range: 0-50 seconds
Example: Conference 1 AutoAnswer Delay: 0
The Conference settings, cont...
Conference [1..1] AutoAnswer Mute
The Autoanswer Mute setting determines whether the microphone is muted when an incoming call is
automatically answered.
Valuespace: <On/Off>
On: The incoming call will be muted when automatically answered.
Off: The incoming call will not be muted.
Example: Conference 1 AutoAnswer Mute: Off
Conference [1..1] MicUnmuteOnDisconnect
The MicUnmuteOnDisconnect setting determines if the microphones should be automatically unmuted
when all calls are disconnected. In a meeting room or other shared resource this could be done to prepare
the system for the next user.
Valuespace: <On/Off>
On: Microphones will be unmuted when all calls are disconnected
Off: Microphones will not be unmuted when all calls are disconnected
Example: Conference 1 MicUnmuteOnDiscon nect: On
Conference [1..1] DoNotDisturb Mode
The Do Not Disturb setting determines whether or not there should be an alert on incoming calls.
Valuespace: <On/Off>
On: Set to On when you want no alert to incoming calls. The calling side will receive a busy signal when
trying to call the codec.
Off: This is the default setting. The DoNotDisturb is automatically turned Off if the codec receives any
IR signal from the handheld remote control.
Example: DoNotDisturb Mode: Off
Conference [1..1] AutoAnswer Mode
The Autoanswer setting determines whether an incoming call is put through automatically or manually.
Valuespace: <On/Off>
On: The system will automatically answer all incoming calls.
Off: All incoming call must be answered manually by pressing the OK key or the green Call key on the
remote control.
Example: Conference 1 AutoAnswer Mode: Off
D14637.01—MARCH 2010
Conference [1..1] FarEndControl Mode
Lets you decide if the remote side (far end) should be allowed to select your video sources and control
your local camera (pan, tilt, zoom).
Valuespace: <On/Off>
On: Set to On when you want the far end to be able to select your video sources and control your local
camera (pan, tilt, zoom). You will still be able to control your camera and select your video sources as
normal.
Off: When set to Off the far end can not access any of the features above on your system.
Example: Conference 1 FarEndControl Mode: On
12
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Advanced config.
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
The Conference settings, cont...The Conference settings, cont...
Administrator guide
Conference [1..1] Encryption Mode
In Point to point calls ( BestEffort mode): If the far end system supports encryption (AES-128), the call will
be encr ypted. If not, the call will proceed without encryption.
In MultiSite calls ( BestEffor t mode ): In order to have encrypted MultiSite conferences, all sites must
suppor t encryption. If not, the conference will be unencr ypted.
Icons on screen: A padlock with the tex t “Encr yption On” displays on screen, for a few seconds, when the
conference starts.
Valuespace: <Off/On/BestEffor t>
BestEffort: The system will use encryption whenever possible.
On: The system will only allow calls that are encrypted.
Specify the Default Call Protocol to be used when placing calls from the system. The call protocol can also
be defined directly for each call when setting up a call.
Valuespace: <H323/SIP>
H.323: Select H.323 to ensure that calls are set up as a H.323 calls.
SIP: Select SIP to ensure that calls are set up as a SIP calls.
Example: Conference 1 DefaultCall Protocol: H323
Conference [1..1] DefaultCall Rate
Specify the Default Call Rate to be used when placing calls from the system. The call rate can also be
defined directly for each call when setting up a call.
Valuespace: <64..6000>
Range: 64-6000 kbps
Example: Conference 1 DefaultCall Rate: 768
Conference [1..1] VideoBandwidth Mode
In “Dynamic” mode the available transmit bandwidth for the video channels is distributed among the
currently active channels. This means that the main video channels will use the bandwidth of the
presentation channel, if there is no active presentation. In “Static” mode the bandwidth is assigned to each
video channel even if it is not active.
Valuespace: <Dynamic/Static>
Dynamic: The available transmit bandwidth for the video channels are distributed among the currently
active channels.
Static: The available transmit bandwidth is assigned to each video channel, even if it is not active.
The available transmit video bandwidth is distributed on the main channel and presentation channel
according to “MainChannel Weight” and “PresentationChannel Weight”. If the main channel weight is 2
and the presentation channel weight is 1, then the main channel will use twice as much bandwidth as the
presentation channel.
The available transmit video bandwidth is distributed on the main channel and presentation channel
according to “MainChannel Weight” and “PresentationChannel Weight”. If the main channel weight is 2
and the presentation channel weight is 1, then the main channel will use twice as much bandwidth as the
presentation channel.
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Advanced config.
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Administrator guide
The H323 Profile settings, cont...The H323 Profile settings
H323 Profile [1..1] Authentication LoginName
The system sends the Authentication Login Name and the Authentication Password to a H.323
Gatekeeper for authentication. The authentication is a one way authentication from the codec to the H.323
Gatekeeper, i.e. the system is authenticated to the gatekeeper. If the H.323 Gatekeeper indicates that no
authentication is required, the system will still try to register. Requires the H.323 Gatekeeper Authentication
Mode to be enabled.
The system sends the Authentication Login Name and the Authentication Password to a H.323
Gatekeeper for authentication. The authentication is a one way authentication from the codec to the H.323
Gatekeeper, i.e. the system is authenticated to the gatekeeper. If the H.323 Gatekeeper indicates that no
authentication is required, the system will still try to register. Requires the H.323 Gatekeeper Authentication
Mode to be enabled.
Valuespace: <S: 0, 50>
Format: String with a maximum of 50 characters.
Example: H323 Prole 1 Authentication Password:
H323 Profile [1..1] Authentication Mode
Set the authentication mode.
Valuespace: <On/Off>
On: If the H.323 Gatekeeper Authentication Mode is set to On and a H.323 Gatekeeper indicates
that it requires authentication, the system will try to authenticate itself to the gatekeeper. Requires the
Authentication ID and Authentication Password to be defined on both the codec and the Gatekeeper.
Off: If the H.323 Gatekeeper Authentication Mode is set to Of f the system will not tr y to authenticate
itself to a H.323 Gatekeeper, but will still try a normal registration.
Example: H323 Prole 1 Authentication Mode: Off
H323 Profile [1..1] CallSetup Mode
The H.323 Call Setup Mode defines whether to use a Gatekeeper or Direct calling when establishing H323
calls.
NOTE! Direct H.323 calls can be made even though the H.323 Call Setup Mode is set to Gatekeeper.
Valuespace: <Direct /Gatekeeper>
Direct: An IP-address must be used when dialling in order to make the H323 call.
Gatekeeper: The system will use a Gatekeeper to make a H.323 call. When selecting this option the
H323 Profile Gatekeeper Address and H323 Profile Gatekeeper Discovery settings must also be
configured.
Example: H323 Prole 1 CallSetup Mode: Gatekeeper
H323 Profile [1..1] Gatekeeper Address
Specifies the IP address of the Gatekeeper. Requires the H.323 Call Setup Mode to be set to Gatekeeper
and the Gatekeeper Discovery to be set to Manual.
Determines how the system shall register to a H.323 Gatekeeper.
Valuespace: <Manual /Auto>
Manual: The system will use a specific Gatekeeper identified by the Gatekeeper’s IP-address.
Auto: The system will automatically tr y to register to any available Gatekeeper. If a Gatekeeper
responds to the request sent from the codec within 30 seconds this specific Gatekeeper will be used.
This requires that the Gatekeeper is in auto discovery mode as well. If no Gatekeeper responds, the
system will not use a Gatekeeper for making H.323 calls and hence an IP-address must be specified
manually.
The H.323 Alias E.164 defines the address of the system, according to the numbering plan implemented
in the H.323 Gatekeeper. The E.164 alias is equivalent to a telephone number, sometimes combined with
access codes.
Valuespace: <S: 0, 30>
Format: Compact string with a maximum of 30 characters. Valid characters are 0–9, * and #.
Example: H323 Prole 1 H323Alias E164: “90550092”
14
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Advanced config.
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Administrator guide
The Network settingsThe H323 Profile settings, cont...
H323 Profile [1..1] H323Alias ID
Lets you specify the H.323 Alias ID which is used to address the system on a H.323 Gatekeeper and will
be displayed in the call lists. E xample: “firstname.surname@company.com”, “My H.323 Alias ID”.
The H.323 Port Allocation setting af fects the H.245 port numbers used for H.323 call signalling.
Valuespace: <Dynamic/Static>
Dynamic: The system will allocate which por ts to use when opening a TCP connection. The reason for
doing this is to avoid using the same ports for subsequent calls, as some firewalls consider this as a
sign of attack. When Dynamic is selected, the H.323 ports used are from 11000 to 20999. Once 20999
is reached they restart again at 11000. For RTP and RTCP media data, the system is using UDP ports
in the range 2326 to 2487. Each media channel is using two adjacent por ts, ie 2330 and 2331 for RTP
and RTCP respectively. The ports are automatically selected by the system within the given range.
Firewall administrators should not tr y to deduce which ports are used when, as the allocation schema
within the mentioned range may change without any further notice.
Static: When set to Static the ports are given within a static predefined range [5555 –6555].
Example: H323 Prole 1 PortAllocation: Dynamic
Network [1..1] Assignment
Defines whether to use DHCP or Static IP assignment.
Changes to this setting requires a restart of the codec.
Valuespace: <Static/DHCP>
Static: The IP Address, Subnet Mask and Default Gateway for the system must be specified in the
respective address fields.
DHCP: The system adresses are automatically assigend by the DHCP server.
Example: Network 1 Assignment: DHCP
Network [1..1] DNS Domain Name
DNS Domain Name is the default domain name suffix which is added to unqualified names.
Example: If the DNS Domain Name is “company.com” and the name to lookup is “MyVideoSystem”, this
will result in the DNS lookup “MyVideoSystem.company.com”.
Valuespace: <S: 0, 64>
Format: String with a maximum of 64 characters.
Example: Network 1 DNS Domain Name: “company.com”
Network [1..1] DNS Server [1..5] Address
Defines the network addresses for DNS servers. Up to 5 addresses may be specified. If the network
addresses are unknown, contact your administrator or Internet Service Provider.
Valuespace: <S: 0, 64>
Format: String with a maximum of 64 characters.
Example: Network 1 DNS Server 1 Add ress: “”
D14637.01—MARCH 2010
Network [1..1] IEEE8021X AnonymousIdentity
The 802.1X Anonymous ID string is to be used as unencrypted identity with EAP types that support
different tunneled identity, like EAP-PEAP and EAP-TTLS. If set, the anonymous ID will be used for the
initial (unencrypted) EAP Identity Request.
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Advanced config.
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
The Network settings, cont...The Network settings, cont...
Administrator guide
Network [1..1] IEEE8021X Eap Md5
Message-Digest algorith 5. Is a Challenge Handshake Authentication Protocol that relies on a shared
secret. MD5 is a Weak security. EAP - Extensible Authentication Protocol. MD5 - Message Digest
Algorithm 5.
Valuespace: <On/Off>
On: The EAP-MD5 protocol is enabled. Default mode is On.
Off: The EAP-MD5 protocol is disabled.
Example: Network 1 IEEE8021X Eap Md5: On
Network [1..1] IEEE8021X Eap Peap
Protected Transport Layer Security. Developed by Microsoft, Cisco and RSA Security. Authenticates LAN
clients without the need for client certificates. E AP - Ex tensible Authentication Protocol. PE AP - Protected
Extensible Authentication Protocol.
Valuespace: <On/Off>
On: The EAP-PEAP protocol is enabled. Default mode is On.
Off: The EAP-PEAP protocol is disabled.
Example: Network 1 IEEE8021X Eap Peap: On
Network [1..1] IEEE8021X Eap TTLS
Tunneled Transpor t Layer Security. Developed by Funk Sof tware and Cer ticom. Usually suppor ted by
Agere Systems, Proxim and Avaya. Authenticates LAN clients without the need for client certificates. EAP Extensible Authentication Protocol. TTLS - Tunneled Transport Layer Security.
Valuespace: <On/Off>
On: The EAP-TTLS protocol is enabled. Default mode is On.
Off: The EAP-TTLS protocol is disabled.
Example: Network 1 IEEE8021X Eap TTLS: On
Network [1..1] IEEE8021X Identity
The 802.1X Identity is the user name needed for 802.1X authentication.
Valuespace: <S: 0, 64>
Format: String with a maximum of 64 characters.
Example: Network 1 IEEE8021X Identity: “”
Network [1..1] IEEE8021X Mode
The system may be connected to an IEEE 802.1X LAN net work with a port-based net work access control
that is used to provide authenticated network access for Ethernet networks.
Valuespace: <On/Off>
On: The 802.1X authentication is enabled.
Off: The 802.1X authentication is disabled. Default mode is Off.
Example: Network 1 IEEE8021X Mode: Off
Network [1..1] IEEE8021X Password
The 802.1X Password is the password needed for 802.1X authentication.
Valuespace: <S: 0, 32>
Format: String with a maximum of 32 characters.
Example: Network 1 IEEE8021X Password: “***”
Network [1..1] IPv4 Address
Defines the Static IP address for the system. Only applicable if Static IP assignment is chosen.
Valuespace: <S: 0, 64>
Format: Compact string with a maximum of 64 characters.
Example: Network 1 IPv4 Address: “10.47.5.100”
Network [1..1] IPv4 Gateway
Defines the IP default gateway. Only applicable if Static IP assignment is chosen.
Valuespace: <S: 0, 64>
Format: Compact string with a maximum of 64 characters.
Example: Network 1 IPv4 Gateway: “10.47.5.100”
Network [1..1] IPv4 SubnetMask
Defines the IP subnet mask. Only applicable if Static IP assignment is chosen.
Valuespace: <S: 0, 64>
Format: Compact string with a maximum of 64 characters.
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Advanced config.
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
The Network settings, cont...The Network settings, cont...
Administrator guide
Network [1..1] IPv4 QoS Mode
Defines whether IP Diffserv QoS should be used. The QoS (Quality of Service) is a method which
handles the priority of audio, video and data in the network. The QoS set tings must be supported by the
infrastructure. DiffServ (Differentiated Services) is a computer networking architecture that specifies a
simple, scalable and coarse-grained mechanism for classifying, managing network traffic and providing
QoS priorities on modern IP networks.
Valuespace: <Off/Dif fserv>
Off: When set to Off no QoS method is used.
Diffserv: Select Diffser v and then go to the Dif fserv sub-menus (Audio, Data, Signalling and Video) to
configure these settings.
Example: Network 1 IPv4 QoS Mode: diffserv
Network [1..1] IPv4 QoS Diffserv Audio
The Dif fServ Audio setting is used to define which priority Audio packets should have in an IP net work.
Enter a priority, which ranges from 0 to 63 for the packets. The higher the number, the higher the priority.
These priorities might be overridden when packets are leaving the network controlled by the local network
administrator.
Valuespace: <0..63>
Audio: A recommended value is DiffServ Code Point (DSCP) is AF41, which equals the value 34. If in
doubt, contact your network administrator.
Range: 0-63
Example: Network 1 IPv4 QoS Diffserv Audio: 0
Network [1..1] IPv4 QoS Diffserv Data
The Dif fServ Data setting is used to define which priority Data packets should have in an IP network.
Enter a priority, which ranges from 0 to 63 for the packets. The higher the number, the higher the priority.
These priorities might be overridden when packets are leaving the network controlled by the local network
administrator.
Valuespace: <0..63>
Data: A recommended value is Dif fSer v Code Point (DSCP) AF23, which equals the value 22. If in
doubt, contact your network administrator.
Range: 0-63
Example: Network 1 IPv4 QoS Diffserv Data: 0
Network [1..1] IPv4 QoS Diffserv Signalling
The Dif fServ Signalling setting is used to define which priority Signalling packets should have in an IP
network. Enter a priority, which ranges from 0 to 63 for the packets. The higher the number, the higher the
priority. These priorities might be overridden when packets are leaving the network controlled by the local
network administrator.
Valuespace: <0..63>
Signalling: A recommended value is DiffServ Code Point (DSCP) AF31 which equals the value 26. If in
doubt, contact your network administrator.
The Dif fServ Video setting is used to define which priority Video packets should have in an IP network.
Enter a priority, which ranges from 0 to 63 for the packets. The higher the number, the higher the priority.
These priorities might be overridden when packets are leaving the network controlled by the local network
administrator.
Valuespace: <0..63>
Video: A recommended value is DiffServ Code Point ( DSCP) AF41, which equals the value 34. If in
doubt, contact your network administrator.
Range: 0-63
Example: Network 1 IPv4 QoS Diffserv Video: 0
Network [1..1] MTU
Set the ethernet MTU (Ma ximum Transmission Unit).
Valuespace: <400..1500>
Range: 400-1500
Example: Network 1 MTU: 1500
D14637.01—MARCH 2010
17
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Advanced config.
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
The Network settings, cont...The Network Services settings
Configure how video packets transmission speed shall be controlled.
Valuespace: <On/Off>
On: Transmit video packets at maximum 20Mbps. Can be used to smooth out bursts in the outgoing
network traffic.
Off: Transmit video packets at link speed.
Example: Network 1 TrafcControl: On
NetworkServices Multiway Address
Set the Multiway address equal to the Conference Factory Alias, as set up on the VCS.
Multiway™ conferencing enables video endpoint users to introduce a 3rd par ty into an existing call. It can
be used in the following situations:
1) When you want to add someone else in to your existing call.
2) When you are called by a 3rd party while already in a call and you want to include that person in the call.
Requirements: The TANDBERG Codec C20 must be running TC3.0 (or later), TANDBERG VCS version
X5 (or later) and TANDBERG Codian MCU version 3.1 (or later). Endpoints invited to join the Multiway™
conference must suppor t the H.323 routeToMC facility message if in an H.323 call, or SIP REFER message
if in a SIP call.
Auto: The system will select the protocol for Multiway calls.
H323: The H323 protocol will be used for Multiway calls.
SIP: The SIP protocol will be used for Multiway calls.
Example: NetworkServices Multiway Protocol: Auto
NetworkServices H323 Mode
Determines whether the system should be able to place and receive H.323 calls.
NOTE! Changes in this setting requires the codec to be restarted.
Valuespace: <On/Off>
On: Set to On to enable the possibility to place and receive H.323 calls.This is the default setting.
Off: Set to Off to disable the possibility to place and receive H.323 calls.
Example: NetworkServices H323 Mode: On
D14637.01—MARCH 2010
18
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Advanced config.
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
The Network Services settings, cont...The Network Services settings, cont...
Administrator guide
NetworkServices HTTP Mode
HTTP is a web-interface for system management, call management such as call transfer, diagnostics and
software uploads.
Valuespace: <On/Off>
On: The HTTP protocol is enabled.
Off: The HTTP protocol is disabled.
Example: NetworkServices HTTP Mode: On
NetworkServices HTTPS Mode
HTTPS is a Web protocol that encrypts and decr ypts user page requests as well as the pages that are
returned by the Web ser ver.
Valuespace: <On/Off>
On: The HTTPS protocol is enabled.
Off: The HTTPS protocol is disabled.
Example: NetworkServices HTTPS Mode: On
NetworkServices HTTPS VerifyServerCertificate
When the system connects to an ex ternal HTTPS server (like a phonebook ser ver or an external manager),
this ser ver will present a certificate to the system to identify itself. This setting tells the system if it should
verify that the certificate is signed by a trusted Cer tificate Authority (CA). This requires that list of trusted
CA’s is uploaded to the system in advance.
Valuespace: <On/Off>
On: Verif y ser ver certificates.
Off: Do not verify ser ver certificates.
Example: NetworkServices HTTPS VerifyServerCerticate: Off
NetworkServices NTP Address
Enter the NTP Address to define the network time protocol server address. This address will be used if
NTP Mode is set to Manual, or if set to Auto and no address is supplied by a DHCP ser ver.
The Network Time Protocol ( NTP) is used to synchronize the time of the system to a reference time server.
The time server will subsequently be queried every 24th hour for time updates. The time will be displayed
on the top of the screen. The system will use the time to timestamp messages transmitted to Gatekeepers
or Border Controllers requiring H.235 authentication. The system will use the time to timestamp messages
transmitted to Gatekeepers or Border Controllers that requires H.235 authentication. It is also used for
timestamping Placed Calls, Missed Calls and Received Calls.
Valuespace: <Auto/Manual>
Auto: The system will use the NTP server, by which address is supplied from the DHCP server in the
network. If no DHCP server is used, or the DHCP server does not provide the system with a NTP
server address, the system will use the static defined NTP server address specified by the user.
Manual: The system will always use the static defined NTP server address specified by the user.
Example: NetworkServices NTP Mode: Manual
NetworkServices SIP Mode
Determines whether the system should be able to place and receive SIP calls.
NOTE! Changes in this setting requires the codec to be restarted.
Valuespace: <On/Off>
On: Set to On to enable the possibility to place and receive SIP calls.This is the default setting.
Off: Set to Off to disable the possibility to place and receive SIP calls.
Example: NetworkServices SIP Mode: On
NetworkServices SNMP CommunityName
Enter the name of the Network Services SNMP Community. SNMP Communit y names are used to
authenticate SNMP requests. SNMP requests must have a ‘password’ (case sensitive) in order to receive a
response from the SNMP Agent in the codec. The default password is “public”. If you have the TANDBERG
Management Suite (TMS) you must make sure the same SNMP Community is configured there too. Note!
The SNMP Community password is case sensitive.
Valuespace: <S: 0, 50>
Format: String with a maximum of 50 characters.
Example: NetworkServices SN MP CommunityNam e: “public”
D14637.01—MARCH 2010
19
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Advanced config.
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
The Network Services settings, cont...The Network Services settings, cont...
Administrator guide
NetworkServices SNMP Host [1..3] Address
Enter the address of up to three SNMP Managers. All traps will then be sent to the hosts listed.
The system’s SNMP Agent (in the codec) responds to requests from SNMP Managers (a PC program
etc.). SNMP Traps are generated by the SNMP Agent to inform the SNMP Manager about impor tant
events. Can be used to send event created messages to the SNMP agent about different events like:
system reboot, system dialing, system disconnecting, MCU call, packet loss etc. Traps can be sent to
multiple SNMP Trap Hosts.
Valuespace: <S: 0, 64>
Format: String with a maximum of 64 characters.
Example: NetworkServices SN MP Host 1 Address: “”
NetworkServices SNMP Mode
SNMP (Simple Network Management Protocol) is used in network management systems to monitor
network-attached devices (routers, ser vers, switches, projectors, etc) for conditions that warrant
administrative attention. SNMP exposes management data in the form of variables on the managed
systems, which describe the system configuration. These variables can then be queried (set to ReadOnly)
and sometimes set (set to ReadWrite) by managing applications.
Valuespace: <Off/ReadOnly/ReadWrite>
Off: Set to Off when you want to disable the SNMP network service.
ReadOnly: Set to ReadOnly when you want to enable the SNMP network service for queries only.
ReadWrite: Set to ReadOnly when you want to enable the SNMP network service for both queries and
commands.
Example: NetworkServices SN MP Mode: ReadWrite
NetworkServices SNMP SystemContact
Enter the name of the Network Services SNMP System Contact.
Valuespace: <S: 0, 50>
Format: String with a maximum of 50 characters.
Example: NetworkServices SN MP SystemContact: “”
NetworkServices Telnet Mode
Telnet is a network protocol used on the Internet or local area network (LAN ) connections.
Valuespace: <On/Off>
On: The Telnet protocol is enabled.
Off: The Telnet protocol is disabled. This is the default factory setting.
Example: NetworkServices Telnet Mode: Off
The Phonebook settings
Phonebook Server [1..5] ID
Enter a name for the external phonebook.
Valuespace: <S: 0, 64>
Format: String with a maximum of 64 characters.
Example: Phonebook Server 1 ID: “”
Phonebook Server [1..5] URL
Enter the address ( URL) to the external phonebook server.
Valuespace: <S: 0, 255>
Format: String with a maximum of 255 characters.
Example: Phonebook Server 1 URL: “http://tms.company.com/tmsapi-exampleublic/
Enter the name of the Network Services SNMP System Location.
Valuespace: <S: 0, 50>
Format: String with a maximum of 50 characters.
Example: NetworkServices SN MP SystemLocation: “”
D14637.01—MARCH 2010
20
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Advanced config.
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Administrator guide
The Serial Port settingsThe Provisioning settings
Provisioning ExternalManager Address
Specifies the IP Address to the External Manager/Management system. If an External Manager address
and a path is configured, the system will post an HTTP message to this address when star ting up.
When receiving this HT TP posting the External Manager (typically a management system) can return
configurations /commands to the unit as a result. If the DHCP Option 242 is returned in the DHCP
response from the DHCP ser ver the system will interpret this as the External Manager address to use.
Valuespace: <S: 0, 64>
Format: String with a maximum of 64 characters.
Example: Provisioning ExternalManager Address: “”
Provisioning ExternalManager Path
Specifies the path to the External Manager/Management system. If an External Manager address
and a path is configured, the system will post an HTTP message to this address when star ting up.
When receiving this HT TP posting the External Manager (typically a management system) can return
configurations /commands to the unit as a result. If the DHCP Option 242 is returned in the DHCP
response from the DHCP ser ver the system will interpret this as the External Manager address to use.
This is the password part of the credentials used to authenticate towards the SIP prox y.
Valuespace: <S: 0, 50>
Format: String with a maximum of 50 characters.
Example: SIP Prole 1 Authentication 1 Password:
SIP Profile [1..1] DefaultTransport
Select the transport protocol to be used over the L AN.
Valuespace: <UDP/TCP/ TLS/Auto>
UDP: The system will always use UDP as the default transpor t method.
TCP: The system will always use TCP as the default transport method.
TLS: The system will always use TLS as the default transport method. For TLS connections a SIP
CA-list can be uploaded using the web interface. If no such CA-list is available on the system then
anonymous Dif fie Hellman will be used.
Auto: The system will try to connect using transport protocols in the following order: TLS, TCP, UDP.
Example: SIP Prole 1 DefaultTransport: Auto
SIP Profile [1..1] Outbound
The client initiated connections mechanism for firewall traversal, connection reuse and redundancy. The
current version suppor ts http://tools.ietf.org/html/draft-ietf-sip-outbound-20.
Valuespace: <On/Off>
On: Set up multiple outbound connections to servers in the Prox y Address list.
Off: Connect to the single proxy configured first in Prox y Address list.
Example: SIP Prole 1 Outbound: Off
SIP Profile [1..1] Proxy [1..4] Address
The Proxy Address is the manually configured address for the outbound proxy. It is possible to use a fully
qualified domain name, or an IP address. The default port is 5060 for TCP and UDP but another one can
be provided. If Outbound is enabled, multiple proxies can be addressed.
Valuespace: <S: 0, 255>
Format: Compact string with a maximum of 255 characters.
Example: SIP Prole 1 Proxy 1 Address: “”
SIP Profile [1..1] Proxy [1..4] Discovery
Select if the SIP Prox y address is to be obtained manually or by using Dynamic Host Configuration
Protocol (DHCP).
Valuespace: <Auto/Manual>
Manual: When Manual is selected, the manually configured SIP Proxy address will be used
Auto: When Auto is selected, the SIP Proxy address is obtained using Dynamic Host Configuration
Protocol (DHCP).
Example: SIP Prole 1 Proxy 1 Discovery: Manual
SIP Profile [1..1] Type
Enables SIP extensions and special behaviour for a vendor or provider.
Standard: Should be used when registering to standard SIP proxy like OpenSer.
Alcatel: Must be used when registering to a Alcatel-Lucent OmniPCX Enterprise R7 or later.
Avaya: Must be used when registered to a Avaya Communication Manager.
Cisco: Must be used when registering to a Cisco CallManager version 5 or later.
Microsoft: Must be used when registering to a Microsoft LCS or OCS server.
Nortel: Must be used when registering to a Nortel MCS 5100 or MCS 5200 PBX.
Experimental: Can be used if auto is not working Note ! This mode is for testing purposes only.
Example: SIP Prole 1 Type: Standard
SIP Profile [1..1] URI
The SIP URI or number is used to address the system. This is the URI that is registered and used by the
SIP services to route inbound calls to the system. A Uniform Resource Identifier (URI) is a compact string
of characters used to identif y or name a resource.
Valuespace: <S: 0, 255>
Format: Compact string with a maximum of 255 characters.
RestoreCameraPosition: Set the camera to the position it had before entering standby.
DefaultCameraPosition: Set the camera to the factor y default position.
Example: Standb y WakeupAction: RestoreCameraPosition
Standby StandbyAction
NEW TC2.1 Decide what the system is going to do when going into standby mode.
Valuespace: <Noneapi-examplerivacyPosition>
None: No action.
PrivacyPosition: Turns the camera to a sideways position for privacy.
Example: Standb y Stand byAction: PrivacyPosition
D14637.01—MARCH 2010
23
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Advanced config.
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
The System Unit settingsThe Time settings
Administrator guide
SystemUnit CallLogging Mode
Enables/disables logging of calls received or placed by the system. The call logs may then be viewed via
the GUI or using the xHistory command.
Valuespace: <On/Off>
On: Enable logging.
Off: Disable logging.
Example: SystemUnit CallLogging Mode: On
SystemUnit IrSensor Mode
The System Unit IR Sensor setting determines whether the infrared receiver on the codec should be
enabled or not. The IR sensor LED is located in the front of the codec and flickers when an ir signal is
received from the remote control.
Valuespace: <On/Off/Auto>
On: Set to On to enable the IR sensor on the codec.
Off: Set to Off to disable the IR sensor on the codec.
Auto: The system will automatically disable the IR sensor on the codec if the IR sensor at camera is
enabled. Otherwise the IR sensor on the codec will be enabled.
Example: SystemUnit IrSensor Mode: On
SystemUnit MenuLanguage
The setting is used to select the language for the GUI (Graphical User Interface).
DD_MM_YY: The date Januar y 30th 2009 will be displayed: 30.01.09
MM_DD_YY: The date Januar y 30th 2009 will be displayed: 01.30.09
YY_MM_ DD: The date January 30th 2009 will be displayed: 09.01.30
Example: Time DateFormat: DD _ MM _ YY
Time TimeFormat
Specifies the time format.
Valuespace: <24H/12H>
24H: Set the time format to 24 hours.
12H: Set the time format to 12 hours.
Example: Time TimeFormat: 24H
SystemUnit Name
Enter a System Name to define a name of the system unit. If the H.323 Alias ID is configured on the system
then this ID will be used instead of the system name. The system name will be displayed :
* When the codec is acting as an SNMP Agent.
* Towards a DHCP ser ver.
Valuespace: <S: 0, 50>
Format: String with a maximum of 50 characters.
Example: SystemUnit Name: “Meeting Roo m Nam e”
D14637.01—MARCH 2010
24
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Advanced config.
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
The Time settings, cont...The Video settings
Administrator guide
Time Zone
Specifies the time zone where the system is located, using Windows time zone description format.
Valuespace: <GMT-12:00 (International Date Line West)/GMT-11:00 (Midway Island, Samoa )/GMT-10:00
(Hawaii)/GMT-09: 00 (Alaska)/GMT-08:00 (Pacific Time (US & Canada) Tijuana)/GMT-07:00 (Arizona)/
GMT-07:00 (Mountain Time (US & Canada ))/GMT-07:00 (Chihuahua, La Paz, Mazatlan)/GMT-06:00
(Central America)/GMT-06:00 (Saskatchewan)/GMT-06: 00 (Guadalajara, Mexico City, Monterrey)/GMT06:00 (Central Time (US & Canada))/GMT-05: 00 (Indiana (East))/GMT-05:00 ( Bogota, Lima, Quito)/
GMT-05:00 (Eastern Time (US & Canada))/GMT-04:30 (Caracas)/GMT-04:00 ( La Pa z)/GMT-04:00
(Santiago)/GMT-04:00 (Atlantic Time (Canada))/GMT-03:30 (Newfoundland )/GMT-03:00 (Buenos Aires,
Georgetown)/GMT-03:00 (Greenland)/GMT-03:00 ( Brasilia)/GMT-02:00 ( Mid-Atlantic)/GMT-01:00 (Cape
Verde Is.)/GMT-01:00 (A zores)/GMT (Casablanca, Monrovia)/GMT ( Greenwich Mean Time : Dublin,
Edinburgh, Lisbon, London )/GMT+01:00 (West Central Africa)/GMT+01:00 (Amsterdam, Berlin, Bern,
Rome, Stockholm, Vienna)/GMT+01:00 (Brussels, Copenhagen, Madrid, Paris)/GMT+01:00 (Sarajevo,
Skopje, Warsaw, Zagreb)/GMT+01:00 (Belgrade, Bratislava, Budapest, Ljubljana, Prague )/GMT+02:0 0
(Harare, Pretoria)/GMT+02:00 (Jerusalem)/GMT+02:00 (Athens, Istanbul, Minsk)/GMT+02: 00 ( Helsinki,
Kyiv, Riga, Sofia, Tallinn, Vilnius )/GMT+02:00 (Cairo)/GMT+02: 00 ( Bucharest)/GMT+03:00 (Nairobi)/
GMT+03: 00 ( Kuwait, Riyadh)/GMT+03:00 (Moscow, St. Petersburg, Volgograd)/GMT+03:00 (Baghdad)/
GMT+03: 30 (Tehran)/GMT+04:00 (Abu Dhabi, Muscat)/GMT+04:00 (Baku, Tbilisi, Yerevan)/GMT+04:30
(Kabul)/GMT+05:00 (Islamabad, Karachi, Tashkent)/GMT+05:00 (Ekaterinburg)/GMT+05:30 (Chennai,
Kolkata, Mumbai, New Delhi)/GMT+05:45 ( Kathmandu)/GMT+06: 00 (Sri Jayawardenepura)/GMT+06:00
(Astana, Dhaka)/GMT+06:00 (Almaty, Novosibirsk)/GMT+06:30 (Rangoon)/GMT+07:00 (Bangkok,
Hanoi, Jakarta)/GMT+07:00 (Krasnoyarsk)/GMT+08:0 0 (Perth)/GMT+08:00 (Taipei)/GMT+08:00 ( Kuala
Lumpur, Singapore)/GMT+08:00 (Beijing, Chongqing, Hong Kong, Urumqi)/GMT+08:00 ( Irkutsk, Ulaan
Bataar)/GMT+09:00 (Osaka, Sapporo, Tokyo)/GMT+09:00 (Seoul)/GMT+09: 00 (Yakutsk)/GMT+09 :30
(Darwin)/GMT+09:30 (Adelaide )/GMT+10:00 (Guam, Port Moresby)/GMT+10:00 (Brisbane)/GMT+10:00
(Vladivostok)/GMT+10:00 (Hobart)/GMT+10:00 (Canberra, Melbourne, Sydney)/GMT+11:00 (Magadan,
Solomon Is., New Caledonia)/GMT+12:00 (Fiji, Kamchatka, Marshall Is.)/GMT+12:00 (Auckland,
Wellington)/GMT+13:00 (Nuku alofa )>
Set the time zone.
Example: Time Zone: “GMT (Greenwich Mean Time : Dublin, Edinburgh, Lisbon,
London)”
Video DefaultPresentationSource
Define which video input source shall be used as the default presentation source (e.g. when you press the
Presentation key on the remote control). The input source is configured to a video input connector.
Valuespace: <1..2>
Select between two presentation sources.
Example: Video DefaultPresentationSource: 2
Video Input DVI [2] Type
The official DVI standard suppor ts both digital and analog signals. In most cases the default AutoDetect
setting can detect whether the signal is analog RGB or digital. However, in some rare cases when DVI-I
cables are used (these cables can carry both the analog and digital signals) this detection might fail. This
setting makes it possible to override the AutoDetect and select the correct DVI video input.
Valuespace: <AutoDetect/Digital /AnalogRGB>
AutoDetect: Set to AutoDetect to automatically detect if the signal is analog RGB or digital.
Digital: Set to Digital to force the DVI video input to Digital when using DVI-I cables with both analog
and digital pins and AutoDetect fails.
AnalogRGB: Set to AnalogRGB to force the DVI video input to AnalogRGB when using DVI-I cables
with both analog and digital pins and AutoDetect fails.
Example: Video Input DVI 2 Type: AutoDetect
Video Input Source [1..2] CameraControl CameraId
Select the ID of the camera in the Visca chain that is connected to this camera source. The CameraId
setting represents the camera’s position in the Visca chain.
Cascaded cameras and Visca commands are described in the PrecisionHD 1080p User Guide. The user
guide is found at www.tandberg.com/docs
Valuespace: <1..1>
Select the ID of the camera in the Visca chain.
Example: Video Input Source 1 CameraControl CameraId: 1
D14637.01—MARCH 2010
Video Input Source [1..2] CameraControl Mode
Determines whether or not the camera control should be enabled for the selected video input source.
Valuespace: <On/Off>
On: Set to On to enable camera control for the camera connected to the selected video input
connector.
Off: Set to Off to disable camera control for the camera connected to the selected video input
connector.
Example: Video Input Source 1 CameraControl Mode: On
25
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Advanced config.
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
The Video settings, cont...The Video settings, cont...
Administrator guide
Video Input Source 1 Connector
Select which video input connector to be active on connector group 1.
Valuespace: <HDMI>
HDMI: Select HDMI when you want to use the HDMI connector as input
Example: Video Input Source 1 Connector: HDMI
Video Input Source 2 Connector
Select which video input connector to be active on connector group 2.
Valuespace: <DVI>
DVI: Select DVI when you want to use the DVI-I connector as input.
Example: Video Input Source 2 Connector: DVI
Video Input Source [1..2] Name
Customizable name of the connector group. Enter the name of the video input source 1-3.
Valuespace: <S: 0, 50>
Format: String with a maximum of 50 characters.
Example: Video Input Source 1 Name: “”
Video Input Source [1..2] OptimalDefinition Profile
The system will automatically choose what resolution and framerate to transmit based on input resolution /
framerate, available bandwidth and wether ths source is configured for motion or sharpness. For motion
sources, this setting can be used to adjust how rapidly the system should increase the transmitted
resolution when increasing bandwidth. For instance, if the source is a camera input is 1920x1080p60, the
system will transmit 1920x720p60 at about 2.2Mb/sec and above with this setting set to normal, but will
will transmit 1920x720p60 at about 1.1Mb/sec and above with this setting set to high. In general you could
choose medium or high if you have good quality video inputs and good lighting conditions, while normal
would give a good experience in most conditions, including not optimal lighting.
Valuespace: <Normal/Medium /High>
See Table 1: Optimal definition for systems suppor ting 1080p and Table 2: Optimal definition for
systems supporting 720p60.
Example: Video Input Source 1 Opti malDenition Prole: Normal
Table 1: Optimal definition, for systems supporting 1080p
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Advanced config.
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
The Video settings, cont...The Video settings, cont...
Administrator guide
Video Input Source [1..2] OptimalDefinition Threshold60fps
For each video input, this set ting tells the system the lowest resolution where it should transmit 60fps. So
for all resolutions lower than this, the maximum transmitted framerate would be 30fps, while above this
resolution 60fps would also be possible, if the available bandwidth is adequate.
When encoding and transmitting video there will be a tradeoff bet ween high resolution and high framerate.
For some video sources it is more important to transmit high framerate than high resolution and vice versa.
The Quality setting specifies whether to give priority to high frame rate or to high resolution for a given
source.
Valuespace: <Motion/Sharpness>
Motion: Gives the highest possible framerate. Used when there is a need for higher frame rates,
typically when a large number of participants are present or when there is a lot of motion in the picture.
Sharpness: Gives the highest possible resolution. Used when you want the highest quality of detailed
images and graphics.
Example: Video Input Source 1 Quality: Motion
Video Layout ScaleToFrame
Defines what to do if the aspect ratio of a video input source doesn’t match the aspect ratio of the
corresponding image frame in a composition. For example if you have a 4:3 input source (like XGA) to be
displayed on a 16:9 output (like HD720).
Manual: If the dif ference in aspect ratio between the video input source and the target image frame is
less than the ScaleToFrameThrshold configuration (in percent), the image is stretched to fit. Unless the
system will maintain the original aspect ratio.
MaintainAspectRatio: Will maintain the aspect ratio of the input source, and fill in black in the rest of the
frame (letter boxing or pillar boxing).
StretchToFit: Will stretch (horizontally or vertically) the input source to fit into the image frame.
Example: Video Layout ScaleToFrame: MaintainAspectRatio
Video Layout ScaleToFrameTreshold
Only applicable if the ScaleToFrame configuration is set to manual. If the difference in aspect ratio bet ween
the video input source and the target image frame is less than the ScaleToFrameThrshold configuration (in
percent), the image is stretched to fit. Unless the system will maintain the original aspect ratio.
Valuespace: <0..100>
Range: Select a value from 0 to 100 percent.
Example: Video Layout ScaleToFrameTreshold: 5
Video Layout Scaling
Defines whether the system should automatically adjust aspect ratio for images or frames when it differs
between the image and the frame it is to be placed in.
Valuespace: <On/Off>
On: Let the system automatically adjust aspect ratio.
Off: Do not do any aspect ratio changes automatically.
Example: Video Layout Scaling: On
Video MainVideoSource
Define which video input source shall be used as the main video source. The input source is configured to
a video input connector.
Valuespace: <1..2>
Range: Select one of the two video sources.
Example: Video MainVideoSource: 1
Video Monitors
The codec can be used with more than one monitor and this setting lets you set the codec’s monitor
layout mode to Single or Dual.
Valuespace: <Single /Dual/DualPresentationOnly>
Single: The same layout is shown on all monitors.
Dual: The layout is distributed on two monitors.
DualPresentationOnly: All participants in the call will be shown on the first monitr, while the presentation
(if any) will be shown on the second monitor.
Example: Video Monitors: Single
D14637.01—MARCH 2010
27
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Advanced config.
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
The Video settings, cont...The Video settings, cont...
Administrator guide
Video OSD InputMethod InputLanguage
The codec can be enabled for Cyrillic input characters in the GUI (Graphical User Interface). NOTE:
Requires that Video OSD inputMethod Cyrillic is set to On.
Valuespace: <Latin/Cyrillic>
Latin: Latin characters can be entered when using the remote control (default setting).
Cyrillic characters can be entered using the remote control. NOTE: Requires a TANDBERG Remote
Control TRC5 with Cyrillic fonts.
Example: Video OSD InputMethod InputLang uage: Latin
Video OSD InputMethod Cyrillic
This configuration is used to hide or show the Cyrillic mode as menu input language in the GUI (Graphical
User Inter face ).
Valuespace: <On/Off>
On: Cyrillic mode is available as a menu input language in the GUI. This will enable the setting Video
OSD InputMethod InputLanguage.
Off: Cyrillic mode is NOT available as a menu input language in the GUI.
Example: Video OSD InputMethod Cyrillic: Off
Video OSD Mode
The Video OSD (On Screen Display) Mode lets you define whether or not information and icons on screen
should be displayed.
Valuespace: <On/Off>
On: Set to On to display the on screen menus, icons and indicators.
Off: Set to Off to hide the on screen menus, icons and indicators.
Example: Video OSD Mode: On
Video OSD Output
The Video OSD (On Screen Display) Output lets you define which monitor should display the on screen
menus, information and icons. By default the OSD output is displayed on the first monitor.
If you have a single monitor and you cannot see any OSD on the monitor: If the OSD output has been
set to the second monitor and the second monitor is not connected, then you cannot see any menus,
information or icons on the screen. To move the OSD output to the first monitor press the following
shortcut sequence on the remote control. Press the Disconnect key followed by: * # * # 0 x # (where x is
output 1 or 2).
Valuespace: <1..2>
Range: Select 1 for HDMI 1 output, or select 2 for HDMI 2 output.
Example: Video OSD Output: 1
Video OSD TodaysBookings
This setting can be used to display the systems bookings for today on the main OSD menu. This requires
that the system is bookable by an ex ternal booking system, like TMS (TANDBERG Management Suite).
Valuespace: <On/Off>
On: Displays information about this systems bookings on screen.
Off: Do not display todays bookings.
Example: Video OSD TodaysBookings: Off
Video Output HDMI [1..2] MonitorRole
The monitor role describes what video stream will be shown on the monitor connected to the output
connector. Applicable only if the “Video > Monitors” configuration is set to dual.
Valuespace: <First/Second/ PresentationOnly>
First: Show main video stream.
Second: Show presentation video stream if active, or other participants.
PresentationOnly: Show presentation video stream if active, and nothing else.
Example: Video Output HDMI 1 MonitorRole: First
Video Output HDMI [1] OverscanLevel
Some TV’s or other monitors may not display the whole image sent out on the systems video output, but
cuts the outer parts of the image. In this case this set ting can be used to let the system not use the outer
parts of video resolution. Both the video and the OSD menu will be scaled in this case.
Valuespace: <Medium /High/ None>
Medium: The system will not use the outer 3% of the output resolution.
High: The system will not use the outer 6% of the output resolution
None: The system will use all of the output resolution.
Example: Video Output HDMI 1 OverscanLevel: None
D14637.01—MARCH 2010
28
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Advanced config.
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
The Video settings, cont...
Video Output HDMI [1..2] Resolution
Select the preferred resolution for the monitor connected to HDMI video output. This will force the selected
resolution on the monitor.
The Video Self view setting determines whether or not the main video source (selfview) should be displayed
on screen.
Valuespace: <On/Off>
On: Set to On when you want self view to be displayed on screen.
Off: Set to Off when you do not want selfview to be displayed on screen.
Example: Video Selfview: On
Administrator guide
Video WallPaper
The Video Wallpaper setting determines whether or not a background picture should be displayed on
screen when idle.
Valuespace: <None/Growing/Summersky/Custom>
None: Set to None if you do not want a wallpaper to be displayed on screen.
Summersky, Growing: Select the wallpaper to be displayed on screen.
Custom: The custom wallpaper is uploaded from the web inter face. Open a web browser and enter
the IP address of the codec. Select “Wallpaper” from the menu on top of the screen. Browse for the
file and press the “Upload” button. Toggle once between “None” and “Custom” wallpaper to make the
change take effect. See the Appendices section for further details about the web interface.
Example: Video Wallpaper: Sum mersky
D14637.01—MARCH 2010
29
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Advanced config.
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Administrator guide
The Experimental menu
The Advanced configurations menu has an option called Experimental. The settings within this menu
can be used ‘as is’ and will not be documented. NOTE! The Experimenal menu WILL change.
Experimental CapsetFilter
The Experimental settings can be used ‘as is’ and will not be fur ther documented. NOTE: The
Experimental settings WILL change.
The Experimental settings can be used ‘as is’ and will not be fur ther documented. NOTE: The
Experimental settings WILL change.
Valuespace: <Auto/Manual>
Example: Experi mental SoftwareUpgrade Mode: Auto
Experimental SoftwareUpgrade ServerAddress
The Experimental settings can be used ‘as is’ and will not be fur ther documented. NOTE: The
Experimental settings WILL change.
Valuespace: <S: 0, 255>
Example: Experi mental SoftwareUpgrade Ser verAddress: “http://csupdate.
tand berg.com/getswlist.py”
Experimental UserInterfaces OSD PhonebookMerged
The Experimental settings can be used ‘as is’ and will not be fur ther documented. NOTE: The
Experimental settings WILL change.
Valuespace: <On/Off>
Example: Experi mental UserInterfaces OSD Phonebook Merged: Off
Example: Experi mental CustomSoftbuttons State 1 Softbutton 1 Type: NotSet
Experimental CustomSoftbuttons State [1..2] Softbutton [1..5] Value
The Experimental settings can be used ‘as is’ and will not be fur ther documented. NOTE: The
Experimental settings WILL change.
Valuespace: <S: 0, 255>
Example: Experi mental CustomSoftbuttons State 1 Softbutton 1 Value: “”
D14637.01—MARCH 2010
30
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Password protection
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Administrator guide
Chapter 3
Password protection
www.tandberg.com
D14637.01—MARCH 2010
31
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Password protection
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Administrator guide
Password protection
The system can be password protected in three ways:
• The Advanced menu can be password protected with a menu
password.
• The Codec can be password protected with an administrator
password.
• The Web inter face is password protected with the same
administrator password as for the codec. NOTE! Requires a
reboot of the codec.
NOTE! When a new password has been defined make sure
you save a copy of the password in a safe place. Contact your
TANDBERG representative if you have forgotten the password.
Setting the codec administrator password
To define the administrator password on the codec:
1. Connect to the codec through the network or the serial data
port, using a command line interface (ssh, telnet or scp)
2. Log in to the codec with user name (admin) and no password.
3. Run the following API command and enter a password:
xCom mand SystemUnit AdminPassword Set
Password: “****”
4. The password format is a string with 0–255 characters.
5. Reboot the codec.
Password protection of the web interface
The web interface is password protected with the same user
name and password as defined for the codec.
NOTE! To activate the administrator password on the web
interface, after having defined or changed the administrator
password, a reboot of the codec is required. Without a reboot
the administrator password will only apply when you log in to the
codec.
Log in to the codec or the web interface
• You can log in to the codec with the user name and password,
either from a web inter face or from a command line interface.
You will need to enter both the user name and password.
• The user name is admin, and cannot be changed.
How to deactivate the administrator password
1. Connect to the codec through the network, using a command
line inter face (ssh, telnet or scp).
2. Login to the codec with the required user name (admin) and
password.
3. Run the following API command with a blank password:
xCom mand SystemUnit AdminPassword Set
Password: ““
4. Reboot the codec.
Setting the menu password
To define a password for the Advanced menus:
1. In the on-screen menu, go to Home > Settings > Advanced
> Set menu password.
2. The password is a string with 0 –255 characters.
3. Enter the new password in the Set password menu
4. Press Save.
Log in to the Advanced menu
When a password is set, the password is required to get access
to the Advanced menu on screen.
How to change the menu password
1. To change the password, go to Home > Settings >
Advanced > Set menu password.
2. Enter the new password in the Set password menu
3. Press Save.
How to deactivate the menu password
1. To deactivate the password, go to Home > Settings >
Advanced > Set menu password.
2. Leave the input field empty in the Set password menu.
3. Press Save to save the blank password. This will deactivate
the menu password.
D14637.01—MARCH 2010
32
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
About monitors
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Administrator guide
Chapter 4
About monitors
www.tandberg.com
D14637.01—MARCH 2010
33
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Contact us
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Administrator guide
About monitors when you have a
Codec C20
Connecting the monitor
The monitor can be connected to video output HDMI 1 (default) or
HDMI 2*. The default resolution for HDMI is 1280x720@60Hz.
Connecting to HDMI 1
When connecting the monitor to HDMI 1, which is the default
video output on Codec C20, the menu, icons and other
information on screen (OSD - on screen display) will be displayed
on this monitor.
Connecting to HDMI 2
When connecting the monitor to HDMI 2* output on Codec
C20 the menus and icons is not automatically displayed on
screen. The OSD must be moved to this output by running a key
sequence on the remote control.
NOTE! There is no audio on HDMI 2.
Moving the OSD using the remote control
When connecting the main monitor to the HDMI 2 output, you
must move the OSD to this output. If you cannot see any menu on
screen you must run a key sequence on the remote control. The
menu on screen, icons and other information (OSD - on screen
display) will be moved to the selected output.
The video outputs at Codec C20
HDMI 1
(the default connector
for the main monitor)
HDMI 2*
Dual monitors
NOTE! Requires the Dual Display option.
When you want to run a dual monitor setup, connect the main
monitor to video output HDMI 1 and the second monitor to video
output HDMI 2 on Codec C20.
Dual monitor configuration
Check which connector the monitor is connected to, and run the
following key sequence on the remote control.
The Camera settings must be set to Motion to ensure the Optimal
Definition to work. With the Camera settings set to Sharpness, the
endpoint will transmit the highest resolution possible, regardless
of frames per second.
To set the camera settings:
• Go to: Settings > Advanced > Advanced settings > Camera.
High (720p60)
Typically used in dedicated video
conferencing rooms. Requires good
lighting conditions for a good overall
experience.
Under ideal conditions the bandwidth
requirements can be reduced by up to
50%.
Medium (w576p60)
Typically used in rooms with better than
normal, and consistent lighting.
The bandwidth requirements can be
reduced by up to 25%.
Administrator guide
Normal (w448p60)
This setting is typically used in office
environments where the environment is
normal to poorly lit.
Generally, we recommend the Optimal
Definition set at Normal.
D14637.01—MARCH 2010
Optimal definition profiles for systems supporting 1080p
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Appendices
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Codec C20–The physical interface
The front panel LEDs
The LED in front of the codec indicates the status of the codec.
• When the LED is OFF the codec is Of f.
• The LED flashesgreen during the boot up and shut down of
the codec.
• The LED pulsesgreen when the infrared (IR ) port is activated.
This will occur when the remote control is in use.
• The LED is steadygreen when the codec is On, in Standby
mode or in Presentation mode.
• When the LED is red this indicates an Error has occurred.
Administrator guide
D14637.01—MARCH 2010
Power Call IR Alarm
(infrared)
37
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Appendices
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Codec C20–The physical interface, continued...
The rear panel
The TANDBERG Quick Set C20/C20plus physical interface is described in this guide.
The connectors used in a basic setup are highlighted in orange.
Administrator guide
Kensington
lock
Mic 1
Mini jack
3,5 mm
Mic 2
Mini jack
3,5 mm
Audio
input
2 x RCA
Audio
output
2 x RCA
Cooling
fan
Microphone 1–2
Mini-Jack 3.5mm, 4-pole connector. Connect the microphone to
Mic 1, which is the main connector.
Audio input
RCA sockets, mixed to mono. Used when connecting to PC and
external playback devices, such as VCR’s or DVD players.
Audio output
RCA sockets, mono. Used when connecting to a local
loudspeaker system.
Network connector
Ethernet interface, 1 × 10Mb/100Mb/1Gigabit Ethernet LAN (RJ45 Jack) interface.
USB
For future use.
Network
RJ45
USB (for
future use)
Camera
control port
RS-232
PC input
DVI-I
input
Camera Control port
Camera Control (RS-232) port for power and camera control
(pan, tilt, zoom) using the VISCA™* protocol. The Pin No. 4 on
the Camera Control port provides 12 V DC / 1 A to the main
camera.
DVI-I input for PC
DVI-I socket, digital/analog video input for PC presentations.
HDMI input for camera
HDMI socket, digital video input for camera.
HDMI output for the main monitor
HDMI socket, digital video and audio output for the main monitor.
HDMI output for the second monitor
HDMI socket, digital video output for the second monitor.
Cooling
fan
Camera
HDMI
input
Main
monitor
HDMI 1
output
Second
monitor
HDMI 2
output
Power
socket
Power
switch
Power socket
The power socket accepts +12V / 5A (max) from the external
adapter.
The external adapter accepts 100/240V 50/60Hz and the
maximal load is 75W.
Power switch
The power switch (push button) is located on the rear side.
• Push the button to boot up the codec.
• Push and hold the button for 1 second to shut down the
codec.
• Push and hold the button for 7 seconds to force a shut down
of the codec.
Kensington lock
The Kensington lock may be used to prevent the codec to be
moved from its place or to prevent theft.
*VISCA™ is a trade mark of S ony Cor porati on
D14637.01—MARCH 2010
38
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Appendices
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Pin-out schemes
This page gives an overview of the pin-out schemes for C20.
Administrator guide
HDMI pin-out
External view of socket
Pin: 19 17 3 1
Pin: 18 16 4 2
RJ-45 Connector pin-out
1 8
TOP
Wiring diagram
standard cable
1 ----------1
2 ----------2
FRONT
1 8
3 ----------3
6 ----------6
Pin-out—VISCA™ camera control
RJ11, 8 pins shielde d modular jack
PinSigna l name
8+12V (prese nce 2.8m A curre nt sourc e when
conne cted in da isy cha in)
7GND
6TXD (out)
5NC (no conne ct)
4NC (no conne ct)
3RXD (in)
2GND
1+12V
DVI-I pin-out
External view of socket
PinAssig nmentPinAssig nment
1T.M.D.S. Data 2+11T.M.D.S. Cloc k Shiel d
2T.M.D.S. Data 2 Shie ld12T.M.D.S. Clo ck–
3T.M.D.S. Data 2 –13CEC
4T.M.D.S. Data 114Reser ved ( N.C. on devi ce)
5T.M.D.S. Data 1 Shie ld15SCL
6T.M.D.S. Data 1 –16SDA
7T.M.D.S. Data 017DDC/C EC Ground
8T.M.D.S. Data 0 Shie ld18+5 V Power (m ax 50 mA )
9T.M.D.S. Data 0–19Hot Plug D etect
10T.M.D.S. Clock+
Signa l nameRJ-45 pinD-SUB pin
+12V DC 1 Twisted p air4
GND 2 5
RX3 Twiste d pair 2
TX 6 3
NC4Twisted pair1
NC 56
GND 7Twisted pair 5
+12V DC8 4
RS232 9 pin D-SUB pin-out
External view of socket
1 5
6 9
HDMI Pin-out
Pin-out—TANDBERG camera cable
Microphone, 3.5 mm Mini-Jack, 4 pole
Microphone control
RCA pin-out
External view of socket
Ground Audio– Hot
GNDSignal
Audio– Cold
Codec C20 audio connectors
Jack Mic inputRCA line inputRCA line outpu t
Conne ctor pin o utTip = Hot
Ring 1 = Co ld
Ring 2 = Mi c. contro l
Shiel d = GND
Signa l typeBalanc edUnbal ancedUnbalance d
Conne ctor (c odec )M ini Jack 3.5mmFem ale RCA /pho noFemale RCA/ phono
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
!
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Appendices
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Connecting to the Codec C20
The illustration shows you the basic setup when connecting the
monitor, PC, camera, microphone, loudspeakers (if applicable),
LAN and line voltage to the TANDBERG Codec C20.
CAUTION! In order to be able to use the system for video calls, all
orange colored sockets must be connected.
Administrator guide
The codec must be switched off and disconnected from
the line voltage whenever connecting or disconnecting
other equipment.
D14637.01—MARCH 2010
HDMIHDMI
40
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Appendices
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Administrator guide
TANDBERG DNAM for
Profile 42”
The TANDBERG DNAM – Digital Natural Audio
Module – is built on two specially designed
and separate modules, the amplifier and the
loudspeaker cabinet.
Audio In - SPDIF (stereo) or Analog (mono),
using the same connector.
Audio Differential In - (female XLR pinout: 1 GND, 2 – Signal (+), 3 – Signal (-))
Audio Loop Out - line out directly from the input,
always analog even with SPDIF in.
Audio Stereo Out - (male XLR, common GND
configuration)
• Fuse 2A 250V Slow, 5 x 20mm, Littelfuse
type 215002. Push and twist anti-clock vice
to release.
D14637.01—MARCH 2010
41
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Appendices
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
CE Declarations
Administrator guide
TANDBERG Quick Set C20/C20 Plus
For an official, signed version of this document, or details regarding documentation from the technical
construction file, please contact TANDBERG.
EC Declaration of conformity
MANUFACTURER:TANDBERG Telecom AS
PRODUCT NAME:TANDBERG Codec C20
TYPE NUMBER:TTC7-18
DESCRIPTION:Video Conferencing Equipment
DIRECTIVES:
This equipment complies with.
HARMONIZED STANDARDS:
Applied in order to verify compliance with
directives.
TEST REPORTS and
CERTIFICATES ISSUED BY:
TECHNICAL CONSTRUCTION FILE NO.:14508
YEAR WHICH THE CE-MARK WAS
AFFIXED:
LVD 2006/95/EC
EMC 2004/108/EC
EN 60950-1:2006
EN 55022 (2006)
EN 55024 (1998) + A1 (2001) + A2 (2003)
EN 61000-3-2 (2006)
EN 61000-3-3 (1995) + A1 (2001) + A2 (2005)
Reports/Certificates No.:
LVD (Nemko AS) 121905
EMC (Nemko AS) E09659.00
2009
TANDBERG Profile using Codec C20
For an official, signed version of this document, or details regarding documentation from the technical
construction file, please contact TANDBERG.
EC Declaration of conformity
MANUFACTURER:TANDBERG Telecom AS
PRODUCT NAME:PROFILE 42
TYPE NUMBER:TTC60-12
DESCRIPTION:Video Conferencing Equipment
DIRECTIVES:
This equipment complies with.
HARMONIZED STANDARDS:
Applied in order to verify compliance with
directives.
TEST REPORTS and
CERTIFICATES ISSUED BY:
TECHNICAL CONSTRUCTION FILE NO.:X14474 rev. 2
YEAR WHICH THE CE-MARK WAS
AFFIXED:
LVD 2006/95/EC
EMC 2004/108/EC
EN 60950-1:2006
EN 55022 (2006)
EN 55024 (1998) + A1 (2001) + A2 (2003)
EN 61000-3-2 (2006)
EN 61000-3-3 (1995) + A1 (2001) + A2 (2005)
Report/Certificates No:
LVD (Nemko AS) 135581
EMC (Nemko AS) E09640.01
2009
D14637.01—MARCH 2010
42
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Appendices
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
China RoHS table
This products described in this guide complies
with the Chineese RoHS.
Administrator guide
D14637.01—MARCH 2010
43
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Appendices
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Administrator guide
Supported RFCs in SIP
The RFC (Request for Comments) series contains technical
and organizational documents about the Internet, including the
technical specifications and policy documents produced by the
Internet Engineering Task Force (IETF).
Current RFCs and drafts supported in SIP
• RFC 1889 RTP: A Transport Protocol for Real-time
Applications
• RFC 2190 RTP Payload Format for H.263 Video Streams
The audio and video media capabilities supported in SIP are the
same as for H.323.
D14637.01—MARCH 2010
44
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Appendices
Administrator guide
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Technical specifications
TANDBERG Codec C20
SET DELIVERED COMPLETE WITH:
Codec C20, PrecisionHD 1080p 4x or 12x camera,
Performanc e Mic 20, remote contro l, cables and power
supply
BANDWIDTH
H.323/S IP up to 6 Mbps point-to-point
FIREWALL TRAVERSAL
TANDBERG Ex pressway™ Technology
H.460.18, H.460.19 Firewall Travers al
VIDEO STANDARDS
H.261, H.263, H.263+, H.264
VIDEO FE ATURES
Native 16: 9 Widescreen
Advanced Screen Layouts
Intelligent Vi deo Management
Local Au to Layout
VIDEO INPUTS (2 INPUTS)
1 X HDMI input, su ppor ted formats :
1920 x 1080@ 60, 59.94 Hz (1080p60)
1920 x 1080@50 Hz (1080p50 )
1920 x 1080@30, 29.97 Hz (1080p30)
1920 x 1080@25 Hz (1080p25)
1920 x 1080@24, 23.97 Hz (1080p24)
1920 x 1200@50 Hz (WUXG A)
1680 x 1050@ 60 Hz ( WSXGA+)
1600 x 1200@ 50, 60 Hz ( UXGA)
1440 X 900@60 Hz (WXG A+)
1400 x 1050@ 60, 75 Hz
1366 x 768@ 60 Hz
1360 x 768@ 60 Hz
1280 x 1024@60, 75, 85 Hz (SXG A)
1280 x 960@ 60, 85 Hz
1280 x 800@ 60 Hz ( WXGA)
1280 x 768@60, 75, 85 Hz (WXGA)
1280 x 720@60, 59.94 Hz (720p60)
1280 x 720@50 Hz (720p50 )
1152 x 864@75 Hz
1024 x 768@60, 70, 75, 85 Hz ( XGA)
848 x 480 @60 Hz (576p50)
800 x 60 0@ 56, 60, 72, 75, 85 Hz (SVG A)
720 x 576@50 Hz
720 x 480@ 60, 59.94 Hz (480p 60)
640 x 480 @60, 72, 75, 85 Hz (VGA)
1 X DVI-I input, s uppor ted format s:
Digit al (DVI-D ):
Same as HDMI, ref. above.
Analog RGB ( DVI-A):
1920 x 1080@ 60 Hz (1080p60)
1920 x 1200@50 Hz (WUXG A)
1680 x 1050@ 60 Hz ( WSXGA+)
1600 x 1200@ 60 Hz ( UXGA)
1440 x 900@60 Hz (WXG A+)
1400 x 1050@ 60, 75 Hz
1366 x 768@ 60 Hz
1360 x 768@ 60 Hz
1280 x 1024@60, 75, 85 Hz (SXG A)
1280 x 960@ 60, 85 Hz
1280 x 800@ 60 Hz ( WXGA)
1280 x 768@60, 75, 85 Hz (WXGA)
1280 x 720@60 Hz (720p6 0)
1152 x 864@75 Hz
1024 x 768@60, 70, 75, 85 Hz ( XGA)
848 x 480 @60 Hz
800 x 60 0@ 56, 60, 72, 75, 85 Hz (SVG A)
720 x 576@50 Hz
720 x 480@ 60, 59.94 Hz (480p 60)
640 x 480 @60, 72, 75, 85 Hz (VGA)
Analog YPbPr ( DVI-A) :
1920 x 1080@ 60 Hz (1080p60)
1920 x 1080@50 Hz (1080p50 )
1920 x 1080@30 Hz (1080p30)
1920 x 1080@25 Hz (1080p25)
1280 x 720@60 Hz (720p6 0)
1280 x 720@50 Hz (720p50 )
1280 x 720@30 Hz (720p30 )
720 x 576@50 Hz ( 576p50 )
720 x 480@ 60 Hz (480p60)
Extended Di splay Id entification Data (EDID)
VIDEO OUTPUTS ( 2 OUTPUTS)
2 X HDMI output, s upported format s:
1920 x 1080@ 60 Hz (1080p60)
1920 x 1200@6 0Hz (W UXGA)
1600 x 1200@ 60 Hz ( UXGA)
1366 x 768@ 60 Hz
1360 x 768@ 60 Hz
1280 x 720@60 Hz (720p6 0)
1280 x 1024@60 Hz (SXGA)
1280 x 768@60 Hz (W XGA)
1024 x 768@60 Hz (XGA)
800 x 60 0@ 60 Hz ( SVGA)
640 x 480 @60 Hz (VGA)
VESA Monitor Power Management
LIVE VIDEO RESOLUTIONS (ENCODE /DECODE )
176 x 144@30 fps (Q CIF)
352 x 288@ 30 fps ( CIF)
512 x 288@ 30 fps (w288p )
576 x 448@ 30 fps (448p)
768 x 448@ 30 fps (w448p )
704 x 576@30 fps (4CIF)
1024 x 576@30 fps ( w576p)
640 x 480 @3 0 fps (VGA)
800 x 60 0@ 30 fps ( SVGA)
1024 x 768@30 fps (XGA )
1280 x 1024@30 fps ( SXGA)
1280 x 720@30 fps (720p30)
1920 x 1080@30 fps (1080p30) *
1280 x 768@30 fps (W XGA)
1440 x 900@30 fps (W XGA+)
1680 x 1050@ 30 fps ( WSXGA+)
1600 x 1200@ 30 fps ( UXGA )
512 x 288@ 60 fps (w288p60)*
768 x 448@ 60 fp s (w448p 60)*
1024 x 576@60 fps (w576p60 )*
1280 x 720@60 fps (720p 60) *
1920x1200@20fps ( WUXGA)
AUDIO STANDARDS
G.711, G.722, G.722.1, 64 bit & 128 bit MPEG4 A AC-LD
AUDIO FE ATURES
CD-Qualit y 20KHz Mono
1 x Acoustic Echo Canceller
Automati c Gain Control (AGC)
Automati c Noise R eduction
Active Lip Synchroniz ation
AUDIO INPUTS (4 INPUTS )
2 x Microp hone, 4 pin MiniJack
2 x RCA/ Phono ( mixed to mono)
AUDIO OUTPUTS ( 3 OUTPUTS)
2 x RCA/ Phono ( dual mono)
1 x HDMI, digital, main audi o
DUAL STRE AM
H.239 (H.323) dual strea m
BFCP (SIP) dua l stream
Support resolutions up to WXG A (1280 x 768)
PROTOCOLS
H.323
SIP
EMBEDDED ENCRYPTION
H.323/S IP point-to-point
Standards-ba sed: H.235 v2 & v3 a nd AES
Automati c key gene ration a nd exchange
Supported in Dual Stre am
IP NET WORK FE ATURES
DNS lookup for se rvice configuration
Differentiated Ser vices (Qo S)
IP adapti ve bandwidth ma nagement (includ ing flow
control)
Auto gateke eper discovery
Dynam ic playout and lip-sync buffering
H.245 DTMF tones in H.323
Date and Time supp ort via NTP
Packet Los s based D ownspeeding
URI Dialing
TCP/IP
DHCP
Direct DNS dialing
802.1x netwo rk authentication
SECURITY FE ATURES
Management v ia HTTPS and SSH
IP Administration Passwo rd
Menu Adm inistration Password
Disable IP ser vices
Network Settings prote ction
NETWORK INTERFACES
D14637.01—MARCH 2010
45
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Appendices
Administrator guide
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
TANDBERG Codec C20, continued...
1 x LAN /Ethe rnet ( RJ-45) 10/100/1000 Mbit
OTHER INTERFACES
USB host for future usage
PRECISIONHD 1080P 12X CAMERA
1/3” CMOS
12 x zoom
+15°/-25° tilt, +/- 90° pan
43.5° vertical fie ld of view
72° horizontal fiel d of view
Focus distance 0.3m– infinity
1920 x 1080 pixels progressive @ 60fps
Other fo rmats suppor ted (configur able through Dipswitch ):
1920 x 1080@ 60 Hz (HDMI only)
1920 x 1080@50 Hz (HDMI only)
1920 x 1080@30 Hz
1920 x 1080@25 Hz
1280 x 720@60 Hz
1280 x 720@50 Hz
1280 x 720@30 Hz
1280 x 720@25 Hz
Automati c or manu al focus/brightn ess/white balance
Far-end camera control
Dual HDMI and HD -SDI output
Upside-down m ountin g with automatic flipping of picture
PRECISIONHD 1080P 4X CAMERA
1/3” CMOS
4 x zoom
+15°/-25° tilt, +/- 90° pan
43.5° vertical fie ld of view
72° horizontal fiel d of view
Focus distance 0.3m– infinity
1920 x 1080 pixels progressive @ 30fps
Other fo rmats suppor ted (configur able through Dipswitch ):
1920 x 1080@30 Hz
1920 x 1080@25 Hz
1280 x 720@30 Hz
1280 x 720@25 Hz
Automati c or manu al focus/brightn ess/white balance
Far-end camera control
Dual HDMI and HD -SDI output
Upside-down m ountin g with automatic flipping of picture
SYSTEM MANAGEMENT
Support for the TANDBERG Management Suite
Total manage ment via embedded SNMP, Telnet, SSH,
XML, SOAP
Remote sof tware upload: via web ser ver, SCP, HTTP,
HTTPS
Remote co ntrol and on-screen menu system
DIRECTORY SERVICES
Support for Local directories (My Contac ts)
Corporate Dire ctory
Unlimi ted entr ies using Ser ver director y suppo rting LDAP
and H.350
Unlimi ted numb er for Co rporate directo ry (th rough TMS)
200 number local directory
Recei ved Calls with Date and Time
Placed C alls with Date and T ime
Missed Calls with Date and Time
POWER
Auto-se nsing power supply
100–240 VAC, 50/60 Hz
45 watts max. for codec an d main camera
OPERATING TEMPER ATURE AND HUMIDITY
0° C to 35° C (32° F to 95° F ) ambient temperature
10% to 90% Relative Humidit y (RH)
STORAGE AND TR ANSPORT TEMPERATURE
-20° C to 60° C (-4° F to 140° F) at RH 10–9 0% (noncondensing )
APPROVALS
Directive 2006/95/EC ( Low-Voltage Directive) — Standard
EN 60950 -1
Directive 2004 /108/EC ( EMC Directive) — Standard EN
55022, Clas s B — Stand ard EN 55024 — Standard EN
61000-3-2/-3-3
Approve d according to UL 60950-1 and CAN/C SA-C22.2
No. 609 50-1-07
Complies with FCC15B Class A
DIMENSIONS
Codec C20:
Length : 15.35in/ 39.0cm
Height: 1.18in/3.0 cm
Depth: 5.0in/12.7cm
WEIGHT
Codec C20:
Weight: 4.0 lbs/1.8kg
All spe cifications are subject to change witho ut notic e,
system sp ecific s may var y.
All images in these materials are for representational
purposes only, actual products may differ.
TANDBERG and Expre ssway are registe red trad emarks or
trademarks of TANDBERG in the U.S. and other c ountri es.
All other tradem arks are property of their respective
owners.
MTBF PRODUCT RELIABILITY/MTBF
The predicted re liabi lity is expres sed in the expected
random Mean Ti me Between Failures ( MTBF ) for the
electronic compone nts base d on the Powe r On Hours:
Power On Hours (POH) > 6 9 000 hours
Useful L ife Cycle > 6 years
ISO 9001 certificate is available upon request
March 2010
* requir es optio n
D14637.01—MARCH 2010
46
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Appendices
Administrator guide
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Technical specifications
TANDBERG Profile 42” using C20
UNIT DELIVERED COMPLETE WITH:
Full HD LCD display, Code c C20, remote control,
PrecisionHD 1080p Camera, Per forma nce Mic rophone 20
and choice of installation confi gurati on: floor stand, wheel
base or wall mount on pedestal.
BANDWIDTH
H.323/S IP up to 6 Mbps point-to-point
FIREWALL TRAVERSAL
TANDBERG Ex pressway™ Technology
H.460.18, H.460.19 Firewall Travers al
VIDEO STANDARDS
H.261, H.263, H.263+, H.264
VIDEO FE ATURES
Native 16: 9 Widescreen
Advanced Screen Layouts
Intelligent Vi deo Management
Local Au to Layout
VIDEO INPUTS (2 INPUTS)
1 X HDMI input, su ppor ted formats :
1920 x 1080@ 60, 59.94 Hz (1080p60)
1920 x 1080@50 Hz (1080p50 )
1920 x 1080@30, 29.97 Hz (1080p30)
1920 x 1080@25 Hz (1080p25)
1920 x 1080@24, 23.97 Hz (1080p24)
1920 x 1200@50 Hz (WUXG A)
1680 x 1050@ 60 Hz ( WSXGA+)
1600 x 1200@ 50, 60 Hz ( UXGA)
1440 X 900@60 Hz (WXG A+)
1400 x 1050@ 60, 75 Hz
1366 x 768@ 60 Hz
1360 x 768@ 60 Hz
1280 x 1024@60, 75, 85 Hz (SXG A)
1280 x 960@ 60, 85 Hz
1280 x 800@ 60 Hz ( WXGA)
1280 x 768@60, 75, 85 Hz (WXGA)
1280 x 720@60, 59.94 Hz (720p60)
1280 x 720@50 Hz (720p50 )
1152 x 864@75 Hz
1024 x 768@60, 70, 75, 85 Hz ( XGA)
848 x 480 @60 Hz (576p50)
800 x 60 0@ 56, 60, 72, 75, 85 Hz (SVG A)
720 x 576@50 Hz
720 x 480@ 60, 59.94 Hz (480p 60)
640 x 480 @60, 72, 75, 85 Hz (VGA)
1 X DVI-I input, s uppor ted format s:
Digit al (DVI-D ):
Same as HDMI, ref. above.
Analog RGB ( DVI-A):
1920 x 1080@ 60 Hz (1080p60)
1920 x 1200@50 Hz (WUXG A)
1680 x 1050@ 60 Hz ( WSXGA+)
1600 x 1200@ 60 Hz ( UXGA)
1440 x 900@60 Hz (WXG A+)
1400 x 1050@ 60, 75 Hz
1366 x 768@ 60 Hz
1360 x 768@ 60 Hz
1280 x 1024@60, 75, 85 Hz (SXG A)
1280 x 960@ 60, 85 Hz
1280 x 800@ 60 Hz ( WXGA)
1280 x 768@60, 75, 85 Hz (WXGA)
1280 x 720@60 Hz (720p6 0)
1152 x 864@75 Hz
1024 x 768@60, 70, 75, 85 Hz ( XGA)
848 x 480 @60 Hz
800 x 60 0@ 56, 60, 72, 75, 85 Hz (SVG A)
720 x 576@50 Hz
720 x 480@ 60, 59.94 Hz (480p 60)
640 x 480 @60, 72, 75, 85 Hz (VGA)
Analog YPbPr ( DVI-A) :
1920 x 1080@ 60 Hz (1080p60)
1920 x 1080@50 Hz (1080p50 )
1920 x 1080@30 Hz (1080p30)
1920 x 1080@25 Hz (1080p25)
1280 x 720@60 Hz (720p6 0)
1280 x 720@50 Hz (720p50 )
1280 x 720@30 Hz (720p30 )
720 x 576@50 Hz ( 576p50 )
720 x 480@ 60 Hz (480p60)
Extended Di splay Id entification Data (EDID)
VIDEO OUTPUTS ( 2 OUTPUTS)
2 X HDMI output, s upported format s:
1920 x 1080@ 60 Hz (1080p60)
1920 x 1200@6 0Hz (W UXGA)
1600 x 1200@ 60 Hz ( UXGA)
1366 x 768@ 60 Hz
1360 x 768@ 60 Hz
1280 x 720@60 Hz (720p6 0)
1280 x 1024@60 Hz (SXGA)
1280 x 768@60 Hz (W XGA)
1024 x 768@60 Hz (XGA)
800 x 60 0@ 60 Hz ( SVGA)
640 x 480 @60 Hz (VGA)
VESA Monitor Power Management
LIVE VIDEO RESOLUTIONS (ENCODE /DECODE )
176 x 144@30 fps (Q CIF)
352 x 288@ 30 fps ( CIF)
512 x 288@ 30 fps (w288p )
576 x 448@ 30 fps (448p)
768 x 448@ 30 fps (w448p )
704 x 576@30 fps (4CIF)
1024 x 576@30 fps ( w576p)
640 x 480 @3 0 fps (VGA)
800 x 60 0@ 30 fps ( SVGA)
1024 x 768@30 fps (XGA )
1280 x 1024@30 fps ( SXGA)
1280 x 720@30 fps (720p30)
1920 x 1080@30 fps (1080p30) *
1280 x 768@30 fps (W XGA)
1440 x 900@30 fps (W XGA+)
1680 x 1050@ 30 fps ( WSXGA+)
1600 x 1200@ 30 fps ( UXGA )
512 x 288@ 60 fps (w288p60)*
768 x 448@ 60 fp s (w448p 60)*
1024 x 576@60 fps (w576p60 )*
1280 x 720@60 fps (720p 60) *
1920x1200@20fps ( WUXGA)
AUDIO STANDARDS
G.711, G.722, G.722.1, 64 bit & 128 bit MPEG4 A AC-LD
AUDIO FE ATURES
CD-Qualit y 20KHz Mono
1 x Acoustic Echo Canceller
Automati c Gain Control (AGC)
Automati c Noise R eduction
Active Lip Synchroniz ation
AUDIO INPUTS (4 INPUTS )
2 x Microp hone, 4 pin MiniJack
2 x RCA/ Phono ( mixed to mono)
AUDIO OUTPUTS (3 OUTPUTS)
2 x RCA/ Phono ( dual mono)
1 x HDMI, digital, main audi o
DUAL STRE AM
H.239 (H.323) dual strea m
BFCP (SIP) dua l stream
Support resolutions up to WXG A (1280 x 768)
PROTOCOLS
H.323
SIP
EMBEDDED ENCRYPTION
H.323/S IP point-to-point
Standards-ba sed: H.235 v2 & v3 a nd AES
Automati c key gene ration a nd exchange
Supported in Dual Stre am
IP NET WORK FE ATURES
DNS lookup for se rvice configuration
Differentiated Ser vices (Qo S)
IP adapti ve bandwidth ma nagement (includ ing flow
control)
Auto gateke eper discovery
Dynam ic playout and lip-sync buffering
H.245 DTMF tones in H.323
Date and Time supp ort via NTP
Packet Los s based D ownspeeding
URI Dialing
TCP/IP
DHCP
Direct DNS dialing
802.1x netwo rk authentication
SECURITY FE ATURES
Management v ia HTTPS and SSH
IP Administration Passwo rd
Menu Adm inistration Password
Disable IP ser vices
Network Settings prote ction
NETWORK INTERFACES
1 x LAN /Ethe rnet ( RJ-45) 10/100/1000 Mbit
D14637.01—MARCH 2010
47
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Appendices
Administrator guide
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
TANDBERG Profile 42”/52”, continued...
OTHER INTERFACES
USB host for future usage
PRECISIONHD 1080P 12X CAMERA
1/3” CMOS
12 x zoom
+15°/-25° tilt, +/- 90° pan
43.5° vertical fie ld of view
72° horizontal fiel d of view
Focus distance 0.3m– infinity
1920 x 1080 pixels progressive @ 60fps
Other fo rmats suppor ted (configur able through Dipswitch ):
1920 x 1080@ 60 Hz (HDMI only)
1920 x 1080@50 Hz (HDMI only)
1920 x 1080@30 Hz
1920 x 1080@25 Hz
1280 x 720@60 Hz
1280 x 720@50 Hz
1280 x 720@30 Hz
1280 x 720@25 Hz
Automati c or manu al focus/brightn ess/white balance
Far-end camera control
Dual HDMI and HD -SDI output
SYSTEM MANAGEMENT
Support for the TANDBERG Management Suite
Total manage ment via embedded SNMP, Telnet, SSH,
XML, SOAP
Remote sof tware upload: via web ser ver, SCP, HTTP,
HTTPS
Remote co ntrol and on-screen menu system
DIRECTORY SERVICES
Support for Local directories (My Contac ts)
Corporate Dire ctory
Unlimi ted entr ies using Ser ver director y suppo rting LDAP
and H.350
Unlimi ted numb er for Co rporate directo ry (th rough TMS)
200 number local directory
Recei ved Calls with Date and Time
Placed C alls with Date and T ime
Missed Calls with Date and Time
POWER
Auto-se nsing power supply
100-120/200-240 VAC, 60/50 Hz, 4.5 A max
Maxi mum power consumption : 390 W
OPERATING TEMPER ATURE AND HUMIDITY
0° C to 35° C (32° F to 95° F ) ambient temperature
10% to 90% Relative Humidit y (RH)
STORAGE AND TR ANSPORT TEMPERATURE
-20° C to 60° C (-4° F to 140° F) at RH 10–9 0% (noncondensing )
APPROVALS
Directive 2006/95/EC ( Low Voltage Directive)– Standard
EN 60950 -1, 2ed
Directive 2004 /108/EC ( EMC Directive) –Standard EN
55022, Clas s A– Standard EN 55024– Stan dard EN
61000-3-2/-3-3
Approve d according to UL 60950-1 and CSA 60950 -1-07
Complies with FCC15B Class A
DIMENSIONS
Height: 63.78” / 162 cm
Width : 38.58” / 98 cm
Depth: 6.7” / 17 cm
WEIGHT
Weight: 202.8 lbs / 92 kg
All spe cifications are subject to change witho ut notic e,
system sp ecific s may var y.
All images in the se materials are for representational
purposes only, actual products may differ.
TANDBERG and Expre ssway are registe red trad emarks or
trademarks of TANDBERG in the U.S. and other countri es.
All other tradem arks are property of their respective
owners.
MTBF PRODUCT RELIABILITY/MTBF
The predicted re liabi lity is expres sed in the expected
random Mean Ti me Between Failures ( MTBF ) for the
electronic compone nts base d on the Powe r On Hour s:
Power On Hours (POH) > 6 9 000 hours
Useful L ife Cycle > 6 years
ISO 9001 certificate is available upon request
March 2010
* requir es optio n
D14637.01—MARCH 2010
48
www.tandberg.com
TANDBERG Quick Set C20/C20 Plus and Profiles using C20
Contact us
Contents
Introduction
Advanced configuration
Password protection
About monitors
Appendices
Contact us
ContentsIntroductionAdvanced configurationPassword protectionAbout monitorsAppendicesContact us
Administrator guide
D14637.01—MARCH 2010
U.S. HEADQUARTERS
TANDBERG
1212 Avenue of the Americas
24th Floor
New York, NY 10036
Telephone: +1 212 692 6500
Fax: +1 212 692 6501
Video: +1 212 692 6535
E-mail: tandberg@tandberg.com
EUROPEAN HEADQUARTERS
TANDBERG
Philip Pedersens vei 20
1366 Lysaker
Norway
Telephone: +47 67 125 125
Fax: +47 67 125 234
Video: +47 67 126 126
E-mail: tandberg@tandberg.com
49
www.tandberg.com
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.