Silvercrest KH 2376 Operating instructions

■ BLUETOOTH CAR RADIO

BLUETOOTH CAR RADIO AUTORÁDIO S BLUETOOTH AUTORÁDIO S FUNKCIOU BLUETOOTH

Operating instructions

Návod k obsluze

Návod na obsluhu

KOMPERNASS GMBH ⋅ BURGSTRASSE 21 ⋅ D-44867 BOCHUM

www.kompernass.com

ID-Nr.: KH2376 06/2009-V3

06/2009

KH 2376

4 5 6 7 8 9

10 11

Operating instructions ...................................................................5

42 43 44 45

28 29

121314151617181920212223242526

Návod k obsluze .........................................................................43

Návod na obsluhu ......................................................................81

353637383940

Index

Introduction . . . . . . . . . . . . . .6

Preface . . . . . . . . . . . . . . . . . . . . . . . 6

Information for these operating

instructions . . . . . . . . . . . . . . . . . . . . 6

Limited liability . . . . . . . . . . . . . . . . . 7

Warnings . . . . . . . . . . . . . . . . . . . . . 7

Proper use. . . . . . . . . . . . . . . . . . . . . 8

Safety . . . . . . . . . . . . . . . . . . . . . . . .8

Basic Safety Instructions . . . . . . . . . .8

Danger from laser radiation . . . . . . . 9

Traﬃ c safety . . . . . . . . . . . . . . . . . .10

Interaction with batteries . . . . . . . .10

Package contents and transport

inspection . . . . . . . . . . . . . . . . . . . .11

Disposal of the packaging . . . . . . .11

Operating elementse

(see foldout sides) . . . . . . . .12

Installation . . . . . . . . . . . . . .14

Connection . . . . . . . . . . . . . . . . . . . 14

Installation . . . . . . . . . . . . . . . . . . .16

Uninstalling the device . . . . . . . . . .18

Initial operation . . . . . . . . . .19

Face plate . . . . . . . . . . . . . . . . . . . . 19

Remote control . . . . . . . . . . . . . . . .20

Handling and operation . . .20

Switching On and Oﬀ . . . . . . . . . .21

Settings . . . . . . . . . . . . . . . . . . . . . . 21

Radio reset (RESET) . . . . . . . . . . . . 23

Radio functions . . . . . . . . . . . . . . . . 23

General CD functions . . . . . . . . . . 26

MP3 CDs functions . . . . . . . . . . . . 28

USB port . . . . . . . . . . . . . . . . . . . . .29

Card reader (SD/MMC) . . . . . . . .30

Record function . . . . . . . . . . . . . . . . 30

Connecting an external audio

device to the car radio . . . . . . . . . .32

Bluetooth operation . . . . . . . . . . . .32

Cleaning . . . . . . . . . . . . . . . .34

Safety instructions . . . . . . . . . . . . . .34

Cleaning . . . . . . . . . . . . . . . . . . . . .34

Troubleshooting . . . . . . . . . .35

Safety instructions . . . . . . . . . . . . . .35

Malfunction causes and remedies .35

Disposal . . . . . . . . . . . . . . . . .38

Disposal of the device . . . . . . . . . . 38

Disposing of the batteries . . . . . . . . 38

Appendix . . . . . . . . . . . . . . .38

Technical data . . . . . . . . . . . . . . . .38

Declaration of EC conformity . . . . 39

Warranty . . . . . . . . . . . . . . . . . . . .40

Importer . . . . . . . . . . . . . . . . . . . . .40

Bluetooth Car Radio KH 2376

Introduction

Preface

Dear customer, by purchasing the Bluetooth car radio you have decided on a quality product

from SilverCrest, which, in terms of technology and functionality, meets the most up-to-date development standards.

Read the information included here so that you can quickly familiarize yourself with your device and thus make full use of its functions.

We wish you a great deal of enjoyable use.

Information for these operating instructions

These operating instructions are a component of the KH 2376 Bluetooth car radio (henceforth designated as the device) and supplies you with important information for intended use, safety, installation and connection as well as operation of the device.

The operating instructions must be constantly kept available close to the device. They are to be read and used by anyone assigned to install, service and repair faults in the device.

Keep these operating instructions and hand them over with the device to any future owners.

This documentation is copyright protected. All rights including those of photographic reproduction, duplication and distribution

by means of particular methods (for example data processing, data carriers and data networks), wholly or partially as well as substantive and technical changes are reserved.

Bluetooth Car Radio KH 2376

Introduction

Limited liability

All technical information, data and information for installation, connection and operation contained in these operating instructions correspond to the latest at time of printing and, to the best of our knowledge, take into account our previous experience and know-how.

No claims can be derived from the details, illustrations and descriptions in these instructions.

The manufacturer assumes no responsibility for damage caused by failure to observe the instructions, improper use, inappropriate repairs, making unauthorized changes or for using unapproved replacement parts.

Warnings

In the existing operation instructions the following warnings are used:

WARNING A warning of this danger level signiﬁ es a possible dangerous

situation.

If the dangerous situation is not avoided it can lead to injuries.

The directives in this warning are there to avoid personal injuries. ►

IMPORTANT

A warning of this danger level signiﬁ damage.

If the situation is not avoided it can lead to property damage.

The directives in this warning are there to avoid property damage. ►

NOTICE

A notice signiﬁ es additional information that assists in the handling of the ► device.

Bluetooth Car Radio KH 2376

es possible property

Proper use

This device is intended only for reception of FM/AM radio stations as well as for the playback of audio and MP3 CDs, MP3 ﬁ les from USB data carriers and SD/MMC memory cards as well as audio signals of external audio devices. In addition you can couple the device with a Bluetooth mobile phone and with the microphone unit use the device as a hands free facility.

This device is not intended for any other use or for uses beyond those mentioned.

WARNING Danger from unintended use!

Danger can come from the device if used for unintended purposes and/or other types of use.

Claims of any kind for damage resulting from unintended use will not be excepted. The oper

Safety

In this chapter you receive important safety information regarding handling of the device.

This device complies with the statutory safety regulations. Incorrect usage can, however, lead to personal injury and property damage.

Introduction

Use the device exclusively for intended purposes. ► Observe the procedures described in these operating instructions. ►

ator alone bears liability.

Basic Safety Instructions

For safe handling of the device observe the following safety information:

Before use check the device for visible external damage. Do not put into ■ operation a device that is damaged or has been dropped.

Bluetooth Car Radio KH 2376

Introduction

Damaged cables or connections should be replaced by authorized qualiﬁ ed ■ persons or by the customer service department.

ersons who, due to their physical, intellectual or motor abilities, are incapable ■

P of operating the device safely may only use the device under supervision or dir

ection from a responsible person. Only permit children to use the device under supervision. ■ Repairs should only be carried out by authorized specialist companies or ■

by the customer service department. Incorrect repairs can result in signiﬁ cant danger

s for the user. In addition warranty claims become void.

A repair to the device during the warranty period may only be carried out by ■ a cutomer service department authorized by the manufacturer otherwise no additional w

Defective components may only be replaced with original replacement parts. ■ Only by using original replacement parts can you guarantee that the safety r

equirements are complied with.

Protect the device from moisture and liquid penetration. ■

Danger from laser radiation

WARNING

arranty claims can be considered for subsequent damages.

The device is equipped with a class 1 laser. Laser radiation is dangerous to the eyesight!

Observe the following safety instructions to avoid exposure of yourself or others to laser radiation:

NEVER open the device. ► Have the device repaired only by a specialist. ► Do not make any modiﬁ cations to the device. ►

Bluetooth Car Radio KH 2376

Traﬃ c safety

WARNING Safety in traﬃ c has the highest priority!

Observe the following safety instructions so that you do not put yourself or others in danger:

Before travel commencement familiarize yourself with the operation of the ► device.

Only oper place to carry out comprehensive operations.

Only remove or insert the face plate when the vehicle is parked. ► Set to a moderate volume so that acoustic signals from the police, ﬁ re ►

department and other rescue services can be heard in good time.

ate the device when the traﬃ c situation allows. Stop in a suitable ►

Interaction with batteries

WARNING Danger from improper use!

For safe handling of batteries observe the following safety instructions:

Do not throw the batteries into a ﬁ re. ► Do not short circuit the batteries. ► Do not attempt to recharge the batteries. ► Regularly check the condition of the batteries. Leaking batter

cause permanent damage to the device. Special caution should be shown when handling damaged or leaking batteries. Danger from acid burns! Wear protective gloves.

Store batteries in a place inaccessible to children. If swallowed seek ► immediate medical attention.

emove the batteries from the remote control if you do not intend to use ►

R the device for extended periods of time.

Introduction

y acid can ►

Bluetooth Car Radio KH 2376

Introduction

Package contents and transport inspection

WARNING Risk of suﬀ ocation!

Packaging material should not be used as a play thing. ► There is a risk of suﬀ ocation!

The de

vice is delivered with the following components as standard: Car radio (incl. face plate) ▯ Installation bracket (Attached) ▯ Bezel frame (Attached) ▯ Fixture plate (incl. securing material) ▯ Remote control ▯ 1 Battery CR2025, 3 V DC ▯ Keys for installation frame (2x) ▯ Case for face plate ▯ Microphone unit with adhesive strip ▯ Operating instructions ▯

NOTICE

Check the contents to make sure everything is there and for visible ► damage.

If the contents ar packaging or through transportation contact the service hotline (see warranty card).

e not complete or are damaged due to defective ►

Disposal of the packaging

The packaging protects the device from transport damage. The packaging materials are selected from the point of view of their environmental friendliness and disposal technology and are therefore recyclable.

The recirculation of packaging into the material circuit saves on raw material and reduces generated waste. Dispose of packaging material that is no longer needed according to the regionally established regulations.

NOTICE

If possible preserve the device's original packaging during the warranty ► period so that in the case of a warranty claim you can package the device

operly for return.

Bluetooth Car Radio KH 2376

Operating Elements

Operating elementse (see foldout sides)

POWER/DIM:

Switch device on and oﬀ / dim display illumination

Multi controller:

Turn to set value/volume

MU:

Switch oﬀ sound/button

TA:

Activate traﬃ c radio/button

SEL:

Press or hold down to access adjustment options

Display

AF:

Alternative frequency search / activate regional programmes

PTY:

Station search by PTY group

DISP:

Show display information

Unlocking the face plate

Card slot for SD/MMC cards

USB port AUX IN:

3,5 mm stereo input socket for the connection of an external audio device

▸▸I:

Title / Station search forwards

I◂◂:

Title / Station search backwards

A/PS:

Automatic station saving

Station button 6/next directory

Station button 5/previous

directory

RDM/4:

Random playback in the CD/ MP3 operation mode, station button 4

INT/3:

Intro function in the CD/MP3 operation mode, station button 3

RPT/2:

Repeat function in the CD/ MP3 operation mode, station button 2

PAU/1:

Stop playback in the CD/ MP3 operation mode, station button 1

Sensor for remote control

BND/ENT:

Select band range/conﬁ rm selection

SCN/REC:

Automatic station search/ Record to a data carrier at the USB port or the SD/MMC card slot

MD/LD:

Set operating mode/ switch to loudness

OPEN:

Reject disc

Holder for the face plate

RESET:

Resetting the device

Theft protection LED

Positions LED of the CD

compartment

Bluetooth Car Radio KH 2376

Operating Elements

CD compartment

ISO-Block connection B Automotive blade

type fuse 10 A

ISO block connection A

Bluetooth antenna Socket for microphone unit

Securing screw

(incl. M5 nut and washer)

LINE OUT:

Audio cinch output L/R for ampliﬁ er

Antenna connection for

DIN antenna plug

POWER/DIM:

Switch device on and oﬀ / dim display illumination

Button I◂◂:

Title / Station search backwards

VOL+:

Volume increase

Button

▸▸I:

Title / Station search forwards

INT/3:

Intro function in the CD/ MP3 operation mode, number button 3

VOL-:

Volume decrease

PTY/7:

Station search by PTY group/ number button 7

Number button 6

DSP/*:

Sound setting/button *

BAND/0:

Select frequency range/ number button 0

Battery compartment

SEL/#:

Press or hold down to access adjustment options/button #

TA/9:

Activate traﬃ c radio station/ number button 9

AF/8:

Alternative Frequency search/ regional programme activation/ number button 8

Number button 5

RDM/4:

Random playback in the CD/ MP3 operation mode/ number button 4

RPT/2:

Repeat function in the CD/ MP3 operation mode/ number button 2

▸II/1:

Playback start or stop/ number button 1

MODE:

Set operation type/ Loudness function

Microphone unit plug

Microphone

TALK button green LED for connection status

Case for face plate

Bezel frame

Installation bracket

Key for installation bracket

Fixture plate

(incl. securing material)

Bluetooth Car Radio KH 2376

Installation

WARNING With the installation of the device damage can occur!

If possible have the device installed by a qualiﬁ ed technician. ► If you want to install the device yourself, for safe and ﬂ awless operation ►

of the device follow the instructions for connection and installation.

Connection

IMPORTANT

The use of incorrect connections can lead to damage to the de

vice.

For installation use the device's ISO connections. The vehicle speciﬁ c ISO ► adapter that you may possibly require can be obtained from a specialist establishment, from a local dealer or from the store's technical department. When using other connection types the warranty becomes void!

Conﬁ guration of the ISO connections

1357

2468

ISO A

Installation

Conﬁ guration

1 unconﬁ gured 2

unconﬁ gured 3 unconﬁ gured 4 Permanent positive 5 Antenna power 6 unconﬁ gured 7 12 V (Ignition positive) 8 Minus (-)

1357

2468

ISO B

Conﬁ guration

1 Rear right +

Rear right -

2 3 Front right + 4 Front right 5 Front left + 6 Front left 7 Rear left + 8 Rear left -

Bluetooth Car Radio KH 2376

Installation

To connect the device to two speakers use only the cables for the front speakers.

NOTICE

Make sure that a permanent positive connection is applied to the station ► memory of connection 4 in the ISO block A.

In some automobile models the standar [4] and [7] in ISO block A are interchanged at the factory. If this is the case the station memory can be lost. To correct this, the connections 7 (Ignition positive) and 4 (Permanent positive) in the ISO Block A must be swapped.

You can connect an external ampliﬁ er to the audio cinch output. For this ► follow the operating instructions for the external ampliﬁ er.

Antenna power connection

IMPORTANT

Possible damage to the device!

ver attach the antenna power connection with the antenna's motor ►

power cable.

The connection for the antenna power is available for a relay controlled antenna. The relay then automatically extends the antenna when the device is switched on. When switched oﬀ the antenna retracts. This connection can also be used to control an external ampliﬁ er. For exact connection information please consult the ampliﬁ er's operating instructions.

d conﬁ guration of the connections ►

Connection of an external ampliﬁ er

For the connection of an external ampliﬁ er use the audio cinch output LINE

OUT

. For this follow the operating instructions for the external ampliﬁ er.

Connecting the microphone unit

For connection of the microphone unit use the microphone unit socket 37.

Bluetooth Car Radio KH 2376

Installation

Connection schematic

Antenna Bluetooth antenna

External ampliﬁ er

Installation

The device can be installed into any standard ISO mounting duct. In the event that your vehicle does not have an ISO mounting duct contact your local specialist establishment, local dealer or the technical department of the store.

NOTICE

Before installation remove, without fail, the two transport securing screws ► on the top of the housing (marked with a red sticker)!

Connect the cable befor plugged in properly and that the system functions correctly.

Installation instructions

Install the device in the duct provided for it or select the installation location so ■ that all buttons can be comfortably reached and the driver is not impeded.

Only connect the device to a properly installed 12 V automotive battery. ■ Only connect the device in the vehicle via an ISO plug. ■ Install the device in such a way as to avoid the development of heat accumu- ■

lation and so that the device is suﬃ ciently

1 34

ISO B

ISO

Microphone unit

e ﬁ nally installing the device. Make sure that it is ►

ventilated.

Bluetooth Car Radio KH 2376

Installation

To avoid function disturbances the installation angle should be less than 30°. ■ Do not install the device in a location where it will be subjected to high ■

temperatures(i.e. direct sunlight or heating vents), heavy contamination and str

ong vibrations.

In the event that changes to the vehicle are necessary contact your vehicle ■ dealer/qualiﬁ ed radio installation facility.

Installing the device into the ISO duct

Pull the installation bracket  housing.

Place the installation bracket into the ISO mounting duct.  Bend the tabs on the installation bracket with a scr

is ﬁ xed ﬁ rmly into the mounting duct (see diagram).

and the bezel frame 67 from the device's

ew driver so that the bracket 

Check to make sure that the bracket is securely ﬁ xed.  Connect the ISO socket block of the device with the two ISO plugs on your 

vehicle. Connect the antenna cable fr

on the device. F

eed the microphone unit cable into the mounting duct and connect it to the  microphone unit socket. Lay the cable in such a way that the microphone unit can be secur phone" on page 32.

Contingently connect the audio cinch cable of an external ampliﬁ er to the  LINE OUT sock

et 39 on the device.

Bluetooth Car Radio KH 2376

om the vehicle antenna to the antenna socket 

ed later in the vehicle interior see chapter "Using the micro-

If necessary secure your device against theft with additional measures.  Attach the securing screw with the anchoring plate 70 and the securing material to the engine ﬁ rewall of the vehicle.

Carefully push the device into the mounting duct until it locks into place.  After all connections have been made activate the  RESET button with a ball

point pen or other pointed object. Attach the face plate as described under "Installing the face plate". 

IMPORTANT

Possible damage to the cable!

Obser

ve the position of the cable when sliding the device into the duct so ►

as to avoid damaging it.

inally put on the bezel frame. 

Uninstalling the device

To remove the installed device proceed as follows:

Remove the bezel frame  Insert the right and left keys 

device. (The tabs are now bent back.)

Installation

into their respective slots on the sides of the

Pull the device out. 

Bluetooth Car Radio KH 2376

Initial operation

Face plate

To protect against theft you can remove the face plate from your device. Do not store the removed face plate in your vehicle.

NOTICE

When the face plate is not inserted into the frame the theft protection ►

on the device blinks.

LED To safeguard the face plate always keep it stored in its case. ►

Installing the face plate

Place the face plate with the left side in the  frame ﬁ rst.

Then ﬁ rmly press the right side until it locks into  place.

Check to mak correctely installed in the frame. If the face plate is incorrectly installed it can result in malfunctions when operating the device.

Removing the face plate

Press the  Tilt the face plate completely forward.  Slide the face plate to the left and then pull ﬁ rst 

the right and then the left side away.

e sure that the face plate is ﬁ rmly and

button to unlock the face plate.

Bluetooth Car Radio KH 2376

Remote control

Inserting the battery

Remove the supplied battery from the packing. To insert the battery and/or change the battery proceed

as follows:

Pull the battery compartment out of the remote control  by pressing the lateral locking device and at the same time pull the batter

Remove the depleted battery and insert a new battery  of the type CR2025 (Button cell) into the battery compar

tment. Be sure to insert the battery with the correct

polarity. Slide the battery compartment back into the remote 

control.

Using the remote control

Point the remote control to the Infrared sensor  device.

NOTICE

You can use the remote control up to a distance of 8 m from the device. ►

Handling and operation

y compartment out.

on the front panel of the

Handling and operation

In this chapter you receive important information for the handling and operation of the device.

NOTICE

Most of the functions can be operated by the buttons on the device as well ► as by the buttons on the remote control. In these instructions operation via the buttons on the de the remote control will be speciﬁ cally highlighted.

If no setting is made and/or no button pushed within approx. 5 seconds the ► device returns to its previous operating mode. Changed settings are saved.

vice is described. Any reference to the pushbuttons on

Bluetooth Car Radio KH 2376

Handling and operation

Switching On and Oﬀ

Press brieﬂ y the  POWER/DIM button to switch the device on. In the display the notice WELCOME appears.

Brieﬂ y touch the  POWER/DIM button to dim the display illumination. T

o switch oﬀ hold down the  POWER/DIM button longer

Settings

WARNING Hearing damage as a result of too high a volume!

If the volume is set too high it can lead to permanent hearing damage.

Set the volume to moderate levels only. ►

Volume

Turn the multi controller to set the volume. 

Bass/Treble/Balance/Fader

Press the  SEL button. The current volume level is shown. Each further press of the SEL button accesses the next setting point.

The following settings are possible: VOL - Volume (from 0 to 45), BAS - Bass (from -7 to +7), TRE - Treble (from -7 to +7) BAL - Balance (sound distribution between the right and left speakers)

(from 8L to 8R)

FAD - Fader (sound distribution between the rear and front speakers)

(from 8R to 8F) Turn the multi controller to change the settings of the displayed menu items. 

further settings with the SEL button

Hold down the  SEL button for approx. 2 seconds and then press the SEL button repeatedly until the desired function is shown in the display.

INVOL - switch on volume

Turn the multi controller to set the volume level, with which the device is to be  set when turned on.

Bluetooth Car Radio KH 2376

Handling and operation

ADJ - Time of day

NOTICE

The device is equipped with an RDS controlled clock. The clock sets itself ► automatically when the EON function is switched on and also continues to run when the r can also set the time of day manually.

Turn the multi controller to the right to set the hours and to the left to set the  minutes.

AVOL - Volume for traﬃ c radio

Turn the multi controller to set the volume level, with which traﬃ c reports are  to be played back.

ON - Information from other stations

When the EON function is switched on the radio switches to traﬃ c radio or PTY groups if the TA or PTY function has been activated.

Turn the multi controller in order to switch the EON function on (EON ON)  or oﬀ (EON OFF).

C - Recording format

Turn the multi controller to set the record format for recording on SD/MMC  and/or USB data carriers, MP3 (MP3 data) or WMA (Windo Audio).

DSP - Equalizer (Digital Sound Processing)

Turn the multi controller to select one of the settings  DSP CLASSIC, DSP

CK, DSP POP, DSP FLAT or DSP NONE. In the setting DSP NONE

no DSP is switched on. The DSP equalizer setting is shown at the bottom of the display.

You can also set the equalizer by pressing the DSP button on the remote control. With this setting DSP is switched oﬀ when the radio frequency is shown again.

adio is switched oﬀ . If you do not receive any RDS signal you

ws Media

Loudness

Hold down the  MD/LD button to switch the loudness function on or oﬀ .

Bluetooth Car Radio KH 2376

Handling and operation

Operating mode

Press the  MD/LD button to switch between radio reception (frequency in- dicator), CD/MP3 operation (CD), card slot (SD/MMC), USB port (USB) and audio input (AUX).

NOTICE

The operating modes CD, SD/MMC and USB can only be accessed when ► the corresponding medium is inserted.

Display

Press repeatedly the  DISP button to display successively the following information:

Radio station, title + interpret, time of day (will automatically be set with RDS reception), PTY settings (these RDS functions are transmitted by the broadcast institutions in various formats; see also the chapter "Radio functions") and frequencies.

NOTICE

When you are not receiving any RDS or PTY information, "PS NONE“ or ► "PTY NONE“ is shown in the display.

Radio reset (RESET)

To reset the device to its factory default settings, press the RESET button with a pointed object, such as a pen.

Reset the device:

when operating for the ﬁ rst time, ▯ after the cable connection, ▯ if not all function buttons are working ▯ when an error message appears in the display. ▯

Radio functions

Select frequency range

Press the  BND/ENT button to switch between USW (FM1, FM2, FM3) and medium wave (MW1, MW2).

Automatic station search

Press brieﬂ y the buttons I◂◂ or ▸▸I to start a station search. The search will  stop when a station is found.

Bluetooth Car Radio KH 2376

Manual station selection

Hold down one of the buttons I◂◂ or ▸▸I for two seconds.  MANUAL ap- pears in the display.

Now press the buttons I◂◂ or ▸▸I to change the frequency in steps of  0,05 MHz (USW) and/or 9 kHz (MW) until the desired frequency is set.

If no button is pr again. AUTO appears in the display..

essed for approx. two seconds the automatic station search is set

Saving radio stations

For each frequency range 6 stations can be saved.

Hold down for approx. 3 seconds one of the station buttons  1 to 6 to sav the currently set station. Successful saving is indicated by a brief switching oﬀ of the tone.

Accessing saved stations

Select with  BND/ENT the frequency range. Press one of the station buttons  1 to 6, to access the sav

Automatic saving

Hold down the  A/PS button for 3 seconds. A search immediately starts whereby each found station remains for approx. ﬁ ve seconds. The station indicator and/or the station frequency blinks and the memory cell is displayed. With weak stations the search will automatically continue.

Handling and operation

ed station.

Running through saved stations

Press brieﬂ y the  A/PS button. All stations will be brieﬂ y selected. When you hear the desired station press brieﬂ y the  A/PS button. The chosen

station r

emains selected.

Alternative Frequency (AF)

You can search for alternative frequencies of a station so that it will always have optimal reception.

Press the  AF button. The display sho for the optimal frequency of the currently selected station.

ws AF. The device then always searches

Bluetooth Car Radio KH 2376

Handling and operation

Regional programmes

A few stations broadcast regional programmes.

In order to playback only the station's regional programme hold down the  AF button until the notice REG ON appear

To again playback the national programme hold down the  AF button until the notice REG OFF appear

Programme mode (PTY)

With the help of this function you can search for stations in a designated genre. The following settings are possible:

s in the display.

NEWS AFFAIRS INFO SPORT EDUCATE DRAMA CULTURE SCIENCE

NOTICE

Please note that this information is dependent on the region, the broadcas- ► ting corporation and the station.

or this function the ► EON function must be switched on.

ching the PTY function on/oﬀ

Swit

To activate the PTY search press the  PTY button. In the display the notice

Y appears.

With the station search only stations of the currently selected PTY identiﬁ cation will be considered.

To deactivate the PTY search press the  PTY button again.

Setting t

Station search by PTY identiﬁ cation

he PTY identiﬁ cation

Hold down the  PTY button and then turn the multi contr dividual PTY identiﬁ cation.

During the display of a PTY identiﬁ cation if you press brieﬂ y the  PTY button or the buttons I◂◂ and/or ▸▸I a sear correspond to this PTY identiﬁ cation.

VARIED POP M ROCK M EASY M LIGHT M CLASSICS OTHER M WEATHER

FINANCE CHILDREN SOCIAL RELIGION PHONE IN TRAVEL LEISURE JAZZ

ch immediately starts for stations, which

COUNTRY NATION M OLDIES FOLK M DOCUMENT TEST ALARM

oller to set the in-

Bluetooth Car Radio KH 2376

Handling and operation

If no station is found that corresponds to this PTY identiﬁ cation the notice NOT FND appears brieﬂ y and then the search ends with the last set station.

Traﬃ c radio (TA - "Traﬃ c Announcement")

For this function the EON function must be switched on.

Press the  TA button to switch this mode on or oﬀ

In the TA mode the device will immediately switch from other stations or operation modes to the radio station, which is currently broadcasting traﬃ c information. With this the volume level entered under TAVOL will be set.

During the playback of traﬃ c radio press the TA button to stop the TA function without switching oﬀ this function.

General CD functions

NOTICE

Dampness and high humidity can cause the CD player to malfunction. In ► this case switch on the vehicle heating to dissipate the dampness before using the de temperatures.

Anti-Shock function (ESP - "Electric Shock Protection")

The device is equipped with an anti shock function. This function serves to compensate for vibrations, for example on uneven streets, and to provide an uninterrupted playback even with device movement. When the device is switched on the memory automatically ﬁ lls with data:

with audio CDs for 10 seconds; ■ with MP3-CDs for 120 seconds. ■

vice. Do not subject the device to any extreemly high or low

Inserting and removing CDs

fold the face plate downward by pressing the face plate's unlocking device.  Push the CD into the CD slot with the inscribed side facing up.  Lock the face plate back into place by folding it upwards. Playback of the CD 

begins. T To remove the CD open the face plate again. Press the  OPEN button. The

CD will be ejected. The de

OC READ appears in the display (Read directory contents).

vice switches to radio mode.

Bluetooth Car Radio KH 2376

Handling and operation

Immediately remove the CD from the CD slot. If an ejected CD is not removed  within approx. 5 seconds the device will draw it back in, however playback of the CD will not start.

Title skip

Press the buttons ▸▸I or I◂◂ to select the next and/or previous title. The title  number will be shown in the display.

Fast forward/backward

Hold down the buttons ▸▸I or I◂◂ longer to start fast forward or backward. 

Stop playback

Press the  PAU/1, button to stop playback. To continue playback press the  PAU/1 button once mor

Repeat function (RPT - Repeat)

Press several times the  RPT/2 button to switch between the repeat functions. The following settings are possible:

RPT ONE: The current title is repeated. – RPT ALL: The entire CD will be repeated. – RPT will not be display

Additionally with MP3 CDs:

RPT DIR: All titles in the current directory will be repeated. –

If the functions RPT ONE or RPT DIR ar display.

ed.

e activated RPT will appear in the

Title sampling

Press the  INT/3 button. In the display INT will be shown. Approx. 10 seconds from all titles will playback one after the other.

Press the  INT/3 button once mor

e to activate normal playback.

Random playback of all titles (RDM - Random)

Press the  RDM/4 button. In the display RDM is shown. A random controlled playback is started. A repeat pressing launches the normal playback.

Bluetooth Car Radio KH 2376

MP3 CDs functions

Playback

The device can playback ﬁ les in the MP3 and WMA formats. ■ A mixture of titles and directories on the same level can result in problems ■

when playing back. During playback the information fr

and are shown successively in the display.

Skip dir

Search functions

Title number search

The last digit of the three digit title input blinks.

ectory

Press the station button  6 to playback the ne button 5 to playback the previous directory. The name of the directory will appear brieﬂ y in the display after which playback begins automatically.

NOTICE

If ﬁ les are located in the CD's main directory the directory name ► ROOT will be sho

wn in the display.

Press the  A/PS button. The notice 001 appears in the display.

Press the  SEL button to switch betw selected digit blinks.

Turn the multi controller to set the blinking digit.  When you have entered the desired title number conﬁ rm the entry with  BND/

ENT. The title will immediately playback.

Handling and operation

om the ID3 tag of the MP3 ﬁ les are read ■

xt directory and/or the station

een the 3 digits of the title number. The

NOTICE

If a title number is selected that does not exist the title with the largest title ► number will playback.

itle name search

Press the  A/PS button twice. The notice A** appear

Bluetooth Car Radio KH 2376

s in the display.

Handling and operation

The ﬁ rst symbol blinks.

Press the  SEL button to switch betw selected symbol blinks.

Turn the multi controller to set the blinking symbol.  When you have set the desired symbol press the  BND/ENT button to sho

all titles that begin with the searched for symbol.

NOTICE

If no titles are found that begin with the set symbol then ► NO MATCH will be sho

wn brieﬂ y and you can carry out the setting again.

Turn the multi controller to select a title and start playback with  BND/ENT.

Searc

h for directories

Press the  A/PS button thr back appears.

Turn the multi controller to switch between the available directories.  Press the  BND/ENT button to select the curr

back of the ﬁ rst title from the selected directory starts immediately.

USB port

The device can handle USB data carriers up to 8 GB. With this the directory structure may contain a maximum of 1024 folders, 4096 ﬁ les and a directory depth of 8 levels.

ee times. The directory that is currently playing

een the 3 digits of the title name. The

ently displayed directory. Play-

Connecting data carriers

Open the protective cap from the USB port.  Connect your USB device to the port. The device searches for MP3 or WMA 

ﬁ les on the data carrier and the notice USB appear Place the protective cap back on the USB port when no USB device is con- 

nected to avoid contamination.

Bluetooth Car Radio KH 2376

s in the display.

Playback and search functions

The operations for playing ﬁ les on the external data carrier as well as the ■ search function are exactly the same as with MP3 CDs.

If the de select the USB data carrier with the MD/LD button.

vice is in another mode ( ■ CD, R

Card reader (SD/MMC)

The device can handle SD/MMC memory cards up to 8 GB. With this the directory structure may contain a maximum of 1024 folders, 4096 ﬁ les and a directory depth of 8 levels.

Connecting data carriers

Slide a memory card into the memory card slot with the marking pointing  to the right. Playback of the MP3 or WMA title on the memory card begins automatically.

Playback and search functions

The operations for playing ﬁ les on the external data carrier as well as the ■ search function are exactly the same as with MP3 CDs.

If the device is in another mode ( ■ CD, R the card reader with the MD/LD button.

Handling and operation

adio, AUX or MMC) you can

adio, AUX or USB) you can select

Record function

NOTICE

With your device you can record data from audio CDs, radio or external audio devices onto USB or SD/MMC data carriers and copy MP3 and/or WMA data from an MP3 CD onto USB or SD/MMC data carriers.

The data will be saved with the following notations:

Recordings have a bitrate of 128 kbps and a sampling frequency of 44 kHz.

Please observe the legal regulations valid in your place of residence regar- ► ding the duplication of copyrighted works. In case of doubt please consult a specialist in y

Title of audio CDs: Track001, Track002, ... ■ Data from MP3 CDs: Music001, Music002, ... ■ Radio recordings: Tuner001, Tuner002, ... ■

our area.

Bluetooth Car Radio KH 2376

Handling and operation

Recording

Place a memory medium into the card slot or connect a data carrier to the  USB port.

t the CD, if necessary, and/or switch on the external audio device. 

Inser With the  MD/LD button set the desir

AUX). If necessary start playback of the external audio device.  Hold down the button  SCN/REC until RE

In the operation mode CD, MMC ALL or USB ALL will be displayed. If no data carrier is connected, on which recordings can be made NO MEDIA will be displayed.

Press repeatedly the button  SCN/REC until the desir displayed. When recording an audio CD you can make an additional setting depending on whether you want to record all titles from the CD (USB/MMC ALL) or only the current title (USB/MMC ONE).

Start recording by pressing the  BND/ENT button.

The audio data is no or WMA). At the beginning of the recording the notice RECORD appears in the display. After that the recording is characterized by a preﬁ xed "R".

NOTICE

When the selected data carrier is full recording automatically moves to the ► other data carrier as long as a corresponding data carrier is connected.

w saved on the data carrier in the format that was set (MP3

ed operations mode (CD, Radio,

C MMC or REC USB is displayed.

ed recording option is

o stop the recording press brieﬂ y the  BND/ENT button once mor

T which WAIT is shown brieﬂ y in the display, the recording is saved.

Copying data from an MP3 CD

You can copy individual titles from an MP3-CD to the external USB data carrier or an SD/MMC memory card.

Place a memory medium into the card slot or connect a data carrier to the  USB port.

During playback of a title from an MP3 CD hold down the  SCN/REC button. The notice C carrier is connected, on which recordings can be made NO MEDIA will be displayed.

Press the  SCN/REC button se COPY USB (copy to a USB data carrier) or COPY MMC (copy to an SD/ MMC memory card).

Bluetooth Car Radio KH 2376

e. After

OPY MMC and/or COPY USB appears. If no data

veral times to select either the copy option

Handling and operation

Start the copy process by pressing the  BND/ENT button.

During the copy process COPY appears in the display and a percentage indicator from 01 - 100 shows the copying progress. After the notice COPY 100 the copying process is ended and playback of the MP3 title continues.

Connecting an external audio device to the car radio

Connect the audio output of an external audio device (i.e. an MP3 player)  via a 3.5 mm stereo jackplug to the socket AUX IN on the front panel of the device.

Select playback of the audio input by pressing, several times, the  MD/LD button until AU

Bluetooth operation

The microphone unit must be connected to the device in order to use the Bluetooth functions. In addition a mobile phone is required that supports the Bluetooth data transmission.

Connecting the telephone to the device

Activate the Bluetooth function on your mobile telephone and conduct a  search for Bluetooth devices.

After a successful search the entry CAR--BT appears for the device in the display of the mobile telephone.

Select this entry for the connection and for the subsequent password request  enter the password 0000 for the de the connection structure once more.

After a successful coupling CONNECT brieﬂ y appears in the device's display and the green LED on the microphone unit lights up.

X is shown in the display.

vice. You may possibly have to conﬁ rm

Using the microphone

During the telephone call you will hear the caller via the speaker connected to the device.

For optimal transmitting of your voice place the microphone unit close to you.  Attach the microphone unit, for example, to the dashboard. For this purpose 

you can use the supplied sticky tape. In this case clean beforehand dust and gr

ease from the surface. The sticky tape can be used for securing on almost

all smooth surfaces.

NOTICE

Do not mount the microphone in the vicinity of speakers otherwise the voice ► quality may deteriorate.

Bluetooth Car Radio KH 2376

+ 86 hidden pages