Rotel RSP-1576 Owners Manual [ru]

0 (0)

STANDBYSTANDBY

RSP-1576

HDMI

MUTE

2CH SUR + DISPLAYBYPASS

VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7

USB PC-USB XLR TUNER CD PHONO BT

5V 2.1A

Owner’s Manual

Manuel de l’utilisateur

Bedienungsanleitung

Manual de Instrucciones

Gebruikershandleiding

Manuale di istruzioni

Bruksanvisning

Инструкция пользователя

RSP-1576

Surround Sound Processor

Processeur Audio Surround

Surround-Prozessor

Procesador de Sonido Envolvente

Surround sound-processor

Processore Surround

Surroundprocessor

Процессор окружающего звука

RSP-1576 Surround Sound Processor

Remote Control Overview ...........................................18

Overview of Buttons and Controls .....................................18

STANDBY 1 and Power ON/OFF Buttons A 18

VOLUME Knob and VOLUME UP/DOWN Buttons =D 18

DISPLAY (DISP) Button 0B 18

SETUP Button H 18

Navigation and ENTER Buttons I 18

MUTE Button -F 18

Input Buttons 4qM 18

SUR+ Buttons 9B 18

Playback Control buttons L 18

DIM Button J 18

SUB, CTR, REAR Buttons B 18

MEM Button E 18

LIGHT Button N 18

ASSISTIVE LIGHT O 18

Automatic Surround Modes ...........................................18

Manually Selecting Surround Modes ....................................19

Digital Audio 19

Analog Stereo 19

Basic Operation ...................................................19

Selecting Inputs 19

USB/iPod Operation ...............................................20

iPod/iPhone Connection 0 20

Playback Control Buttons L 20

Bluetooth. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Bluetooth Connection 20

Rear PC-USB .....................................................20

Rear PC-USB Connection 20

Setup ..........................................................20

Menu Basics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Navigation Buttons 20

Main Menu 20

Conﬁguring Inputs .................................................20

Input Setup 21

Multi Input Setup 22

Conﬁguring Audio ..................................................22

Audio Conguration 22

Conﬁguring Speakers and Audio .......................................22

Speaker Conguration 22

Advanced Speaker Setup 23

Subwoofer Setup 24

Speaker Level Setup 24

Speaker and Delay/Distance Setup 25

Miscellaneous Settings ..............................................25

System Setup 25

Video Setup 26

PEQ Conguration 27

Troubleshooting ...................................................27

Specications .....................................................28

Contents

Important Safety Instructions ..........................................4

Figure 1: Control and Connections 5

Figure 2: Remote Control 6

Figure 3: Amplier And Subwoofer 7

Figure 4: Digital Audio and PC-USB Connections 8

Figure 5: Blu-Ray and Video Player Connections 8

Figure 6: Front USB Connections 9

Figure 7: CD Player Connections 9

Figure 8: Tuner Connections 10

Figure 9: Front HDMI Connections 10

Figure 10: Rear HDMI Connections 11

On-Screen Menus 12

About Rotel ......................................................13

Getting Started ...................................................13

Video Features 13

Audio Features 13

Surround Features 13

Other Features 13

Unpacking 13

Placement 13

Overview of Connections ............................................14

HDMI Inputs and Outputs ............................................14

Rear HDMI IN 1–6 Video Inputs r 14

Front HDMI IN 6 14

HDMI Monitor Outputs e 14

Audio Inputs and Outputs ............................................14

PHONO Input f 14

TUNER Input f 14

CD Input f 14

AUX Input f 15

BALANCED Input d 15

MULTI Input g 15

PREAMP Output h 15

DIGITAL Inputs w 15

PC-USB Input t 15

Front USB Input 5 15

Other Connections .................................................15

AC Input j 15

Master Power Switch a 15

12V TRIGGER Output i 15

REM IN Jack o 16

IR OUT Jacks p 16

Rotel Link [ 16

Rear USB Power Port \ 16

RS232 Connector y 16

NETWORK Connector u 16

Making Connections ................................................16

Connecting an External Amplier 16

Connecting a Subwoofer 16

Connecting a DVD, Blu-ray, Cable, Satellite, Game Console and HDTV Tuner 16

Connecting a Blu-ray or DVD Player 17

Connecting a Display 17

Connecting a CD Player or XLR Source 17

Connecting a Tuner 17

Connecting an iPod/iPhone 17

Front Panel Overview ..............................................17

Front Panel Display 3 17

IR Remote Sensor 2 17

Rotel products are designed to comply with international

directives on the Restriction of Hazardous Substances

(RoHS) in electrical and electronic equipment and

the disposal of Waste Electrical and Electronic

Equipment (WEEE). The crossed wheelie bin symbol

indicates compliance and that the products must be

appropriately recycled or processed in accordance

with these directives.

STANDBYSTANDBY

RSP-1576

HDMI

MUTE2CH SUR + DISPLAYBYPASS

VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7

USB PC-USB XLR TUNER CD PHONO BT

5V 2.1A

Pin Assignments

Balanced Audio (3 pole XLR):

Pin 1: Ground / Screen

Pin 2: In phase / +ve / Hot

Pin 3: Out of phase / -ve / Cold

RSP-1576 Surround Sound Processor

Notice

The RS232 connection should be handled by authorized persons only.

WARNING: There are no user serviceable parts inside. Refer all servicing to qualified service personnel.

WARNING: To reduce the risk of fire or electric shock, do not expose the unit to moisture or water. Do

not expose the unit to dripping or splashing. Do not place objects filled with liquids, such as vases, on the

unit. Do not allow foreign objects to get into the enclosure. If the unit is exposed to moisture, or a foreign

object gets into the enclosure, immediately disconnect the power cord from the wall. Take the unit to a

qualified service person for inspection and necessary repairs.

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has two blades and a third grounding prong. The

wide blade or the third prong are provided for your safety. If the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

Only use attachments/accessories specified by the manufacturer.

Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or

sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

Unplug this apparatus during lightning storms or when unused for long periods of time.

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate

normally, or has been dropped.

The apparatus should be used in non tropical climate.

You must allow a minimum 10 cm or 4 inches of unobstructed clearance around the unit.

WARNING: The rear panel power cord connector is the mains power disconnect device. The device must

be located in an open area that allows access to the cord connector.

The unit must be connected to a power supply only of the type and voltage specified on the rear panel.

(USA: 120 V/60Hz, EC: 230V/50Hz)

Connect the component to the power outlet only with the supplied power supply cable or an exact equivalent.

Do not modify the supplied cable. Do not use extension cords.

The mains plug is the disconnect of the unit. In order to completely disconnect the unit from the supply

mains, remove the main plug from the unit and the AC power outlet. This is the only way to completely

remove mains power from the unit.

The main plug is used as the main disconnect device and should remain ready accessible.

The batteries in remote control shall not be exposed to excessive heat such as sunshine, fire or the like.

Batteries should be recycled or disposed as per state and local guidelines.

WARNING: The master power switch is located on the rear panel. The unit must allow unobstructed

access to the main power switch.

Important Safety Instructions FCC Information

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction, may cause harmful interference

to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.(TV, radio, etc.).

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for additional help.

Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following to conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

interference in a residential installation. This equipment generates and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause interference to radio or TV

communications. There is no guarantee that interference will not occur in a particular installation. If this

equipment does cause interference to radio or television reception, which can be determined by turning

the equipment off and on, try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the unit and the television tuner.

• Connect the unit to an AC power outlet on a different electrical circuit.

• Consult your authorized Rotel retailer for assistance.

DAB

STANDBYSTANDBY

RSP-1576

HDMI

MUTE

2CH SUR + DISPL AYBYPASS

VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7

USB PC-USB XLR TUNER CD PHONO BT

5V 2.1A

PUSH

1 2

e i

]

[

uytr

6 78

Figure 1: Control and Connections

Commandes et Connexions

Bedienelemente und Anschlüsse

Controles y Conexiones

Bedieningselementen en aansluitingen

Controlli e connessioni

Kontroller och anslutningar

Органы управления и соединения

RSP-1576 Surround Sound Processor

Figure 2: Remote Control

Télécommande

Fernbedienung

Mando a Distancia

Afstandsbediening

Telecomando

Fjärrkontroll

Пульт дистанционного управления

SUBWOOFER

INPUT

REAR LEFT

AMPLIFIER

CB RIGHT (2)

CB LEFT (1)

REAR RIGHT

AMPLIFIER

FRONT LEFT

AMPLIFIER

CENTER

AMPLIFIER

FRONT RIGHT

AMPLIFIER

PUSH

Figure 3: Amplier And Subwoofer

Amplicateurs et caissons de graves

Verstärker und Subwoofer

Amplicador y Subwoofer

Versterker en subwoofer

Collegamento di amplicatori e subwoofer

Förstärkare och subbas

Усилитель и сабвуфер

RSP-1576 Surround Sound Processor

PUSH

CD PLAYER

Computer

OPTICAL

COAXIAL

DIGITAL AUDIO OUTPUT

MULTICHANNEL ANALOG OUTPUT

FRONT R SUBREAR R CENTRE FRONT LREAL L

DVD or BLUERAY PLAYER

PUSH

Figure 4: Digital Audio and PC-USB Connections

Connexions audio numériques et PC-USB

Digitale Audio und PC-USB verbindungen

Conexiones Digitales de Audio y PC-USB

Digitale audio- en PC-USB-aansluitingen

Collegamenti audio digitale e PC-USB

Digitala ljud- och PC-USB-anslutningar

Подсоединения цифрового аудио и PC-USB

Figure 5: Blu-Ray and Video Player Connections

Connexions à un lecteur Blu-Ray ou Vidéo

Anschlussdiagramm für Blu-Ray- und Video-Player

Conexiones para Reproductor de Video o Blu-Ray

Aansluitingen voor een Blu-Ray of Video-speler

Collegamento di lettori Blu-Ray o Video

Blu-Ray- eller Video-spelare

Подключения Blu-Ray или Видео проигрывателя

STANDBYSTANDBY

RSP-1576

HDMI

MUTE2CH SUR + DISPLAYBYPASS

VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7

USB PC-USB XLR TUNER CD PHONO BT

5V 2.1A

CD PLAYER

AUDIO OUTPUT

RIGHT LEFT

DIGITAL

ANALOG

BALANCED AUDIO OUTPUT

RIGHT LEFT

PUSH

Figure 6: Front USB Connections

Connexions USB en face avant

Frontseitiger USB-Anschluss

Conexiones USB del Panel Frontal

USB-aansluiting op het voorpaneel

Ingresso USB frontale

USB-anslutning på fronten

Подключение USB-накопителей к фронтальному порту

Figure 7: CD Player Connections

Connexions à un lecteur de CD

Anschlussdiagramm für einen CD-Spieler

Conexiones para Reproductor de CD

Cd-speleraansluitingen

Collegamento di un lettore CD

CD-spelare

Подключения CD-плеера

RSP-1576 Surround Sound Processor

AUDIO OUTPUT

RIGHT LEFT

DIGITAL

ANALOG

PUSH

TUNER

Figure 8: Tuner Connections

Connexions à un tuner

Anschlussdiagramm für einen Tune

Conexiones para Sintonizador

Aansluitingen voor Tuner

Collegamento di un Sintonizzatore

Tuner Anslutning

Подключение Тюнера

STANDBYSTANDB Y

RSP-1576

HDMI

MUTE

2CH SUR + DISPLAYBYPASS

VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7

USB PC-USB XLR TUNER CD PHONO BT

5V 2.1A

Figure 9: Front HDMI Connections

Connexions HDMI avant

Vorderseite HDMI-Verbindungen

Conexiones HDMI del Panel Frente

HDMI-aansluitingen op de voorzijde

Collegamento delle prese HDMI anteriore

HDMI-anslutning på främre

Подключение к HDMI разъему на передний панели

480p/576p/720p/1080i/1080p HDTV/ 4K UHDTV

Blu-ray Player or other digital source with HDMI output

PUSH

Figure 10: Rear HDMI Connections

Connexions HDMI arrières

Rückseitige HDMI-Verbindungen

Conexiones HDMI del Panel Posterior

HDMI-aansluitingen op de achterkant

Collegamento delle prese HDMI posteriori

HDMI-anslutning på baksidan

Подключение к HDMI разъему на задней панели

RSP-1576 Surround Sound Processor

INPUT SETUP

SPEAKER CONFIGURATION

SPEAKER DISTANCE SETUP

SUBWOOFER SETUP

SPEAKER LEVEL SETUP

VIDEO SETUP

PEQ CONFIGURATION

SYSTEM SETUP

EXIT

AUDIO CONFIGURATION

MAIN MENU

SOURCE

NAME

VIDEO INPUT

AUDIO INPUT

TRIGGER OUTPUT

DEFAULT MODE

AUDIO DELAY

LEVEL ADJUST

BACK

INPUT SETUP

VIDEO 1

HDMI Audio

Mul Input

1 _ _

Source Dependent

0m sec

0dB

FRONT

CENTER

SURROUND

SUBWOOFER

OVERHEAD REAR

ADVANCED SETUP

BACK

CENTER BACK

OVERHEAD FRONT

SPEAKER CONFIGURATION

Large

Small

Yes

None

SOURCE

NAME

VIDEO INPUT

TRIGGER OUTPUT

LEVEL ADJUST

BACK

INPUT SETUP

MULTI INPUT

M-INPUT

HDMI1

1 _ _

0dB

SPEAKER

CROSSOVER

DOLBY

DTS

STEREO

BACK

ADVANCED SPEAKER SETUP

Front

100Hz

Default

FRONT LEFT

CENTER

FRONT RIGHT

SURROUND RIGHT

CENTER BACK RIGHT

CENTER BACK LEFT

SURROUND LEFT

SUBWOOFER

BACK

OVERHEAD FRONT RIGHT

OVERHEAD REAR RIGHT

OVERHEAD REAR LEFT

OVERHEAD FRONT LEFT

SPEAKER LEVEL SETUP

0dB

SOURCE

NAME

VIDEO INPUT

AUDIO INPUT

TRIGGER OUTPUT

DEFAULT MODE

AUDIO DELAY

LEVEL ADJUST

BACK

FIXED VOLUME

INPUT SETUP

PC-USB

HDMI 1

USB Audio 2.0

1 _ _

Source Dependent

0m sec

0dB

Variable

DOLBY

STEREO

MULTI LPCM

MULTI INPUT

BACK

SUBWOOFER SETUP

DTS

0dB

STANDBY VIDEO SOURCE

FAST AUDIO SYNC

VIDEO SETUP

Disable

OSD FORMAT

BACK

480P

Disable

FRONT

CENTER

SURROUND

SUBWOOFER

CENTER BACK

HEIGHT 1

HEIGHT 2

BACK

CONFIGURATION

AUDIO CONFIGURATION

Front

Center

Surround

Subwoofer

Center Back

Overhead Front

Overhead Rear

7.1.4

SPEAKER : Front Le

FREQUENCY : 20Hz

FREQUENCY : 40Hz Q : 1 GAIN : 0

FREQUENCY : 60Hz Q : 1 GAIN : 0

FREQUENCY : 120Hz Q : 1 GAIN : 0

FREQUENCY : 200Hz Q : 1 GAIN : 0

FREQUENCY : 500Hz Q : 1 GAIN : 0

FREQUENCY : 1200Hz Q : 1 GAIN : 0

FREQUENCY : 4000Hz Q : 1 GAIN : 0

FREQUENCY : 12000Hz Q : 1 GAIN : 0

FREQUENCY : 20000Hz

Q : 1

PEQ CONFIGURATION

BACK

GAIN : 0

Q : 1

ERASE ALL SETTINGS!

BACK

RESTORE FACTORY DEFAULT

OFF TIMER

BACK

SIGNAL SENSE INPUT

POWER MODE

POWER OPTION

20 MINS

Disable

Normal

MAX POWER ON VOLUME 45

LANGUAGE

IR REMOTE CODESET

PEQ FUNCTION

DISPLAY

NETWORK CONFIGURATION

SOFTWARE INFORMATION

RESTORE FACTORY DEFAULT

BACK

POWER OPTION

SYSTEM SETUP

English

Codeset 1

Disable

HDMI And VFD

IP ADDRESS MODE

VIEW NETWORK SETTINGS

TEST NETWORK CONNECTION

BACK

NETWORK CONFIGURATION

RENEW DHCP IP ADDRESS

DHCP

FRONT LEFT

CENTER

FRONT RIGHT

SURROUND RIGHT

CENTER BACK RIGHT

CENTER BACK LEFT

SURROUND LEFT

SUBWOOFER

BACK

OVERHEAD FRONT RIGHT

OVERHEAD REAR RIGHT

OVERHEAD REAR LEFT

OVERHEAD FRONT LEFT

SPEAKER DISTANCE SETUP

10.00 FT 3.05M

On-Screen Menus

Afchage des menus à l’écran

On-Screen-Menüs

Sistema de Menús en Pantalla

Schermmenu’s

Menù sul display (OSD)

Menyer

Экранные меню

About Rotel

Our story began over 50 years ago. Over the decades, we have received

hundreds of awards for our products and satised hundreds of thousands

of people who take their entertainment seriously- like you!

Rotel was founded by a family whose passionate interest in music led them

to manufacture high-delity components of uncompromising quality. Through

the years, that passion has remained undiminished and the family goal of

providing exceptional value for audiophiles and music lovers, regardless

of their budget, is shared by all Rotel employees.

Rotel’s engineers work as a close team, listening to, and ne tuning, each

new product until it reaches their exacting musical standards. They are

free to choose components from around the world in order to make that

product the best they can. You are likely to nd capacitors from the United

Kingdom and Germany, semiconductors from Japan or the United States,

while toroidal power transformers are manufactured in Rotel’s own factory.

We all have concerns about our environment. And, as more and more

electronics are produced it is especially important for a manufacturer to do all

it can to engineer products that have a minimum impact on the environment.

At Rotel, we are proud to do our part. We have reduced the lead content

in our products by using special lead-free ROHS solder and components.

Our engineers continually strive to improve power supply efciency without

compromise to quality. When in standby mode Rotel products use minimal

power to meet global Standby Power Consumption requirements.

The Rotel factory is also doing their part to help the environment through

constant improvements to product assembly methods for a cleaner and

greener manufacturing processes.

All of us at Rotel thank you for buying this product. We are sure it will bring

you many years of enjoyment.

Manufactured under license from Dolby Laboratories. Dolby, Pro Logic,

and the double-D symbol are registered trademarks of Dolby Laboratories.

For DTS patents, see http://patents.dts.com. Manufactured under license

from DTS Licensing Limited. DTS, the Symbol, DTS in combination with the

Symbol, DTS:X, and the DTS:X logo are registered trademarks or trademarks

of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All

Rights Reserved.

Getting Started

Thank you for purchasing the Rotel RSP-1576 Surround Sound Processor.

The unit is a full-featured audio/video control center for analog and digital

source components. It features digital processing for a wide range of formats

including Dolby

Surround, Dolby

ATMOS and DTS

source material.

Video Features.

• HDMI switching for digital video signals up to 4K.

• Accepts HDMI video input: 480i, 480p/576p, 720p, 1080i, 1080p,

1080p 24Hz, 4K.

• Outputs HDMI video (480i, 480p/576p, 720p, 1080i, 1080p, 1080p

24Hz, 4K) compatible with common HDMI displays and projectors.

Audio Features

• Rotel’s Balanced Design Concept combines advanced circuit board

layout, comprehensive parts evaluation, and extensive listening tests

for superior sound and reliability.

• Analog bypass mode for pure 2 channel stereo with no digital processing.

• Digital and analog inputs including Coax, Optical, RCA and Balanced

XLR.

• 7.1 Multi-Channel input from compatible source components.

Surround Features

• Automatic Dolby

and DTS surround decoding of all popular formats

up to 7.1.4 channels.

• Surround modes for playback of multi channel audio on 2 channel

and 3 channel systems.

• Audio Return Channel (ARC) allowing the audio from the TV to be

processed by the RSP-1576 via HDMI.

Other Features

• User friendly ON-SCREEN DISPLAY (OSD) menu system with

programmable labels for all inputs.

• Multi language support in OSD setup.

• Upgradable software to accommodate future updates through the rear

Internet connection or front USB port.

• Assignable 12V trigger outputs for remote turn-on of power amplier(s)

and other components.

Unpacking

Remove the unit carefully from its packaging. Find the remote control and

other accessories. Save the box as it will protect the product if you move

or need to return it for maintenance.

Placement

Place the unit on a solid, level surface away from sunlight, heat, moisture,

or vibration. Make sure that the shelf can support the weight of the unit.

RSP-1576 Surround Sound Processor

Place the unit close to the other components in your system and, if possible,

on its own shelf or with the optionally included rack ears. This will make

initial connection, and subsequent system changes easier.

The unit can generate heat during normal operation. Do not block ventilation

openings. Allow a minimum of 10 cm or 4 inches of unobstructed space

around the unit. If installed in a cabinet, make sure that there is adequate

ventilation.

Do not stack other components or objects on top of the unit. Do not let any

liquid fall into the cabinet.

Overview of Connections

NOTE: Do NOT plug any system component into an AC source until

all connections have been properly made.

Source components within the system can be connected to the unit’s inputs

with either a pair of standard RCA cables or balanced XLR cables for analog

audio, or digitally, via HDMI, coax or optical.

Outputs of the RSP-1576 are sent to the power amplier(s) with standard

RCA cables from the preamp audio outputs. The video signal from the

RSP-1576 is sent to the monitor using the HDMI connections.

In addition, the processor has MULTI INPUT connections for use with a

source component that does its own surround decoding, remote IR receiver

inputs, 12V trigger outputs.

NOTE: The S/PDIF digital audio interface standard specifies a 75

ohm impedance and all good digital cables adhere to this requirement.

Do NOT substitute conventional audio interconnect cables for digital

signals. Standard audio interconnects will pass these signals, but their

limited bandwidth reduce performance.

When using analog audio connections ensure the Left and Right signals are

attached to the proper RCA jacks. All RCA-type connections on this product

follow these standard color codes:

Left channel audio: white RCA jack

Right channel audio: red RCA jack

NOTE: Each source input must be properly configured using the INPUT

SETUP menu of the OSD menu system. We recommend going to this

menu after connecting each source to configure it as desired. See Input

Setup in the Setup section for more information.

HDMI Inputs and Outputs

These connections are used for connecting video signals to and from the

unit. See the Making Connections section for speciﬁc instructions for each

type of component on page 16.

Rear HDMI IN 1–6 Video Inputs r

HDMI inputs provide digital video connections for use with components that

have HDMI outputs. HDMI connections carry video signals in multiple formats

including 3D, 1080p/24Hz, and 4K. The implementation of HDMI supports

audio signals, or a separate audio connection from an HDMI component.

All HDMI inputs support 4K UHD HDCP 2.2 as labeled on the rear panel.

Front HDMI IN 6

The Video 7 input is located on the front panel for easier access. Use

this HDMI connection for portable sources or devices that would not be

permanently connected.

HDMI Monitor Outputs e

The two HDMI outputs of the RSP-1576 can send High Denition video

signals to two display devices in parallel. The HDMI outputs can send video

signals to a high-deﬁnition TV 2D (480p/576p, 720p, 1080i, 1080p or

4K) and 3D (up to 1080p/24Hz). Both HDMI output will support 4K UHD

HDCP 2.2 as labeled on the rear panel.

There are two HDMI outputs on the rear panel sending out the same video

signal. Only one of the two will send the On Screen Menu to your TV.

Of the two HDMI Outputs, only one HDMI output supports ARC (Audio

Return Channel) and is labeled “ARC/OSD” above the HDMI connector.

Please refer to the INPUT SETUP menu section of this manual for more

details on page 21.

Your TV may have more than one HDMI input. Not all HDMI inputs support

ARC. Please use the ARC enabled HDMI input of your TV to use the ARC

function on this product. ARC compatible inputs should be labeled with

“ARC” next to the HDMI input connector.

Additional information for HDMI video outputs:

• All HDMI attached devices must be HDCP compatible to ensure proper

display of the HDMI video signal.

• Audio received over HDMI will be processed by this product and sent

out via the RCA terminal outputs.

• When using both HDMI outputs simultaneously, both HDMI outputs

will be set to the same resolution. This resolution will be the lower

resolution of any attached monitor.

Audio Inputs and Outputs

This Rotel processor provides both analog and digital audio connections.

PHONO Input f

A Left/Right pair of RCA analog audio inputs for connecting a phono player

with a moving magnet cartridge. If the turntable has a “ground” wire, connect

it to the screw terminal labeled “GND” to the left of the Digital inputs.

TUNER Input f

A Left/Right pair of RCA analog audio inputs for connecting a tuner.

CD Input f

A Left/Right pair of RCA analog audio inputs for connecting a CD player.

By default the CD source is set to CD analog RCA input, but this can be

changed to XLR, Coax 1-3 or Optical 1-3 in the input setup menu.

AUX Input f

A Left/Right pair of RCA analog audio inputs for connecting a audio

playback device with an analog audio output.

BALANCED Input d

A Left/Right pair of Balanced XLR audio inputs for connecting a source

component with Balanced XLR audio outputs.

MULTI Input g

A set of RCA inputs accepting up to 7.1 channels of analog signals from a

source component capable of decoding multi channel audio. These inputs

support FRONT L & R, CENTER, SUB, REAR L & R, and CENTER BACK

L[1] & R[2].

These inputs bypass all digital processing in the RSP-1576 and are routed

directly to the volume control and outputs.

PREAMP Output h

A group of fourteen RCA analog audio outputs sends the RSP-1576’s line

level output signals to external ampliers and powered subwoofers. These

output levels are variable and adjusted by the RSP-1576’s volume control.

The fourteen connectors provide output for: FRONT L & R, REAR L & R,

CENTER BACK L[1] & R[2], CENTER 1 & 2, SUBWOOFER 1 & 2, HEIGHT

1 L & R and HEIGHT 2 L & R.

DIGITAL Inputs w

The RSP-1576 accepts digital inputs from source components such as CD

players, satellite TV tuners, and DVD players. The DSP in the RSP-1576

detects the sampling rate of the incoming signal and automatically adjusts.

Sampling rates up to 192kHz are supported.

NOTE: Digital inputs support both 2 Channel Stereo and Multi Channel

audio signals. When using the digital input with a Multi Channel

audio signal the processor DSP will decode the incoming audio stream

including Dolby or DTS.

There are six digital audio inputs on the rear panel, three coaxial and

three optical. These digital inputs can be assigned to any of the VIDEO

1 - 7 input sources using the INPUT SETUP menu during the setup process.

For example, you can assign the COAXIAL 1 digital input connector to the

VIDEO 1 source and the OPTICAL 2 digital input to the VIDEO 3 source. By

default, the source of the audio for inputs Video 1 - 7 is set to HDMI Audio.

By default the CD source is set to CD analog RCA input, but this can be

changed to XLR, Coax 1-3 or Optical 1-3 in the input setup menu.

PC-USB Input t

See Figure 4

Connect this input using the supplied USB cable to the USB socket of your

computer.

The RSP-1576 supports both USB Audio Class 1.0 and USB Audio Class 2.0

modes. Windows computers do not require installation of a driver for USB

Audio Class 1.0 and support playback of audio up to 96kHz sampling rates.

The Factory Default setting is USB Audio Class 2.0. To take advantage of

USB Audio Class 2.0 audio playback supporting up to 192kHz sampling

rates you will need to install the Windows driver supplied on the CD included

with the RSP-1576.

You can switch the RSP-1576 to USB Audio Class 1.0 playback mode with

the following:

• Press SETUP on the remote control to enter MAIN MENU and use

Up/Down buttons to select the INPUT SETUP menu then press ENTER.

• Use Left/Right buttons to select “PC-USB” as INPUT SOURCE and select

“USB Audio 1.0” as AUDIO INPUT.

• Power cycle the RSP-1576 and reboot your PC after changing the USB

Audio mode to ensure both units are properly congured.

Many audio playback applications do not support 192kHz sampling rate.

Please conrm your audio player supports 192kHz audio and you have

192kHz audio les to properly playback this sample rate. Also, you may

need to congure the audio driver in your PC to output 192kHz or your

computer may “down sample” to a lower audio sample rate. For more

information please refer to your audio player or operating system information.

NOTE: Upon successful installation of the driver, you may need to select

the ROTEL audio driver from the audio/speaker setup of your computer.

Front USB Input 5

See Figure 6

This connection will accept Apple devices such as iPod, iPad and iPhone.

While connected, the iPod and iPhone displays remain active allowing

search and play functions.

Other Connections

AC Input j

Your Rotel processor is conﬁgured at the factory for the proper AC line

voltage in the country where you purchased it (USA: 120 volts/60 Hz

AC or CE: 230 volts/50 Hz AC). The AC line conﬁguration is noted on a

decal on the back of your unit. Plug the supplied cord into the AC INPUT

receptacle on the back of the unit.

Master Power Switch a

The large rocker switch on the rear panel is a master power switch. When

it is in the OFF position, power to the unit is completely off. When it is in

the ON position, the front panel STANDBY and remote control ON/OFF

buttons can be used to activate the unit or put it into standby mode.

12V TRIGGER Output i

Many Rotel ampliers offer the option of turning them on and off using a

12 volt trigger. These three connections provide this 12 volt trigger signal

from the processor. When the unit is activated, a 12 volt DC signal is sent

from these jacks to the ampliers to automatically turn them on. When the

processor is put in STANDBY mode, the trigger signal is removed and the

ampliers automatically turn off.

To use the automatic trigger turn on feature, connect one of the RSP-1576’s

12V TRIG OUT jacks to the 12 volt trigger input of a Rotel amplier, using

only the black 3.5 mm trigger cable included with this unit or a Rotel

amplier. Do not use any other cable for trigger connection. The +12V DC

signal appears at the “tip” of the connector.

The 12V Trigger outputs are conﬁgured to turn on in various combinations

only when speciﬁc input sources are activated. See the INPUT SETUP menus

in the Setup section of this manual for details on page 21.

RSP-1576 Surround Sound Processor

REM IN Jack o

This 3.5 mm mini-jack receives command codes from third-party IR remote

receiver. These remote IR inputs can be used when the RSP-1576 front IR

receiver cannot be reached by a sending remote control.

Consult your authorized Rotel dealer for more information on the REM IN jack.

The IR signals from the REM IN jack can be relayed to other source components

using external IR emitters or hard-wired connections from the IR OUT jacks.

See the following section for additional information.

IR OUT Jacks p

The IR OUT 1 & 2 jacks send IR signals received at the REM IN jack to

an infrared blaster or emitter placed in front of a source component’s IR

sensor. In addition, the IR OUT can be hard-wired to other Rotel products

with a REM IN jack.

These outputs allow IR signals to be “relayed” through the RSP-1576 either

directly to the IR receiver on the front panel or via the REM IN jack on the

rear panel. This function provides easy control of other source components

when their IR inputs are not accessible such as when they are installed in

a rack system or in a cabinet.

See your authorized Rotel dealer for more information on IR emitters and

repeater systems.

Rotel Link [

Rotel Link is not used for RSP-1576.

Rear USB Power Port \

The rear USB port provides 5V for charging or powering USB devices

including streaming music players. This port does not allow playback of audio.

The port can be congured to remain powered even when the RSP-1576 is

in standby mode through the front panel setup menu (See the Power Mode

under the Power Option menu on page 26).

The Power Mode “Quick” option allows the attached streaming source to

remain powered for use with the Signal Sense function for automatic power

on/off control of the RSP-1576.

NOTE: When configured to provide continuous power to the rear

panel USB port the RSP-1576 will consume additional power even

when in standby mode.

RS232 Connector y

The RSP-1576 can be controlled via RS232 for integration with automation

systems. The RS232 connector accepts a standard straight DB-9 Male-to-

Female cable.

NETWORK Connector u

The Network socket accepts standard RJ-45, CAT-5 cables. The network

connection is not required for normal operation of this unit. This connection

is for software updates or control from an automation system only.

For additional information on the connections, cabling, software, and

operating codes for automation system control or software updates, contact

your authorized Rotel dealer.

Making Connections

Connecting an External Amplier

See Figure 3

The RSP-1576 has preamp RCA outputs for connections to external power

ampliers to drive up to 12 speakers in congurations from 5.1 to 7.1.4.

In addition, there are two subwoofer outputs.

To connect ampliers, connect an audio cable from each output jack to the

input of the amplier channel that will power the corresponding speaker.

For example, connect the FRONT L output to the amplier channel driving

the front left speaker. There are two CENTER RCA jacks; use either jack for

a single center channel, or both if you have two center channels. In six or

seven channel systems, make one or two additional connections for Center

Back channel(s). These jacks are labeled CB L[1] and CB R[2]. Use CB L[1]

for a single center back channel. Ceiling or Overhead speakers should be

connected to the Height 1 and Height 2 jacks.

For preamp output connection information see Audio Conguration options

in the RSP-1576 Setup Menu on page 22.

After you have connected the preamp outputs, you need to conﬁgure the

RSP-1576 for the size and style of speakers in your system and calibrate the

relative volume levels of the speakers. See the Speaker Level Setup section

of this manual on page 24.

Connecting a Subwoofer

See Figure 3

To connect a powered subwoofer, connect a standard RCA audio cable

from the jacks labeled SUB 1/SUB 2 to the input on the subwoofer’s power

amp. Both SUB outputs provide the same signal. Use either connection

for a single subwoofer. Use both connections to connect two subwoofers.

After you have connected the subwoofer, you need to conﬁgure the unit to

use the subwoofer and calibrate the relative volume level of the subwoofer.

See the Speaker Level Setup section of this manual on page 24.

Connecting a DVD, Blu-ray, Cable, Satellite, Game Console and HDTV Tuner

See Figure 5 and 9

Source devices including Blu-ray, DVD, satellite, cable, etc. should be attached

to the RSP-1576 using HDMI. Connect an HDMI cable from the output of

the source to one of the HDMI inputs on the processor.

Digital audio connection: Depending on the setup of your system, you can also

use the audio digital connections and assign them to the HDMI video inputs.

Connect the digital output of the source to any of the DIGITAL IN OPTICAL

1–3 or DIGITAL IN COAXIAL 1–3 inputs on the processor. An HDMI cable

carries both digital video and digital audio signals; therefore, in most cases

no separate digital audio connection needs to be made.

Use the INPUT SETUP screen to assign the audio digital input to the HDMI

video input source used above.

Although there are typically no video connections for a CD Player, the

RSP-1576 can assign another video input to the CD or XLR input. The Video

choices are HDMI 1-7 (Front), Last Video Source, or Off. HDMI 1 video

input is assigned to CD and XLR as the default setting.

Connecting a Tuner

See Figure 8

Digital audio connection: If using an HD Radio or other digital tuner, connect

the digital output of the tuner to the Optical or Coax digital inputs on the

RSP-1576. Use the INPUT SETUP menu to assign the audio input to the

TUNER source (the default is TUNER analog input jacks).

Analog audio connection:

Option 1: If using an analog tuner, connect the left and right analog outputs

from the tuner to the pair of analog input jacks labeled TUNER on the

RSP-1576. Make sure that you connect the right channel to the R input jack

and the left channel to the L input jack.

Option 2: If your Tuner has XLR output connectors, you can use the XLR inputs

on the RSP-1576 for this connection. Connect the left and right XLR outputs

from the source to the jacks labeled BALANCED INPUT (left and right).

Although there are typically no video connections for a Tuner, the

RSP-1576 can assign another video input to the Tuner input. The Video

choices are HDMI 1 - 7 (Front), Last Video Source, or Off. HDMI 1 video

input is assigned to the Tuner input as a default setting.

Connecting an iPod/iPhone

See Figure 6

Connect the iPod/iPhone to the front USB socket.

NOTE: The audio inputs CD, PHONO, XLR, MULTI, USB, PC-USB,

BLUETOOTH, and TUNER are set to HDMI 1 video input as the factory

default. Video input can be changed to HDMI 1-7 (Front), Last Video

Source, or Off.

Front Panel Overview

The following is a brief overview of the controls and features on the front

panel of the unit. Details concerning the use of these controls are provided

in subsequent sections of this manual describing various tasks.

Front Panel Display 3

The Display on the front panel shows the volume, DSP mode, source selected

and type of audio mode the unit is receiving or processing.

IR Remote Sensor 2

This sensor receives IR signals from the remote control. Do not block this sensor.

NOTE: The remainder of the buttons and controls on the front panel

are described in the Overview of Buttons and Controls section.

Connecting a Blu-ray or DVD Player

See Figure 5

In some cases DVD, SACD, and other external multichannel processors are

connected to the processor by sending decoded analog audio signals using

RCA cables. A player with HDMI outputs can send digital signals directly

to the processor for decoding.

Analog Connections: To connect a Blu-ray or DVD player (or any device that

decodes multi-channel audio) with analog connections, use audio RCA cables

to connect the outputs of the player to the RCA jacks labeled MULTI INPUT

on the RSP-1576. Make sure that you observe proper channel consistency,

i.e. connect the right front channel to the FRONT R input, etc.

Depending on your system conﬁguration, make six connections (FRONT L

& R, REAR L & R, CENTER, and SUBWOOFER), seven connections (adding

a CENTER BACK connection), or eight connections (adding two CENTER

BACK connections).

The MULTI inputs are analog bypass inputs, passing signals directly to the

Volume Control and preamp outputs, bypassing all of the digital processing.

HDMI digital connection: If the player has HDMI outputs, simply connect

an HDMI cable from the output of the player to one of the HDMI inputs

on the processor. This cable sends the video signal from the player along

with a digital audio signal. Using HDMI for audio and video allows the

multichannel decoding to be handled by the processor.

Connecting a Display

See Figure 10

Connect one of the HDMI outputs of the RSP-1576 to the HDMI input of

your TV or projector. The RSP-1576 has two HDMI outputs. Only one HDMI

output will display the OSD and is ARC enabled. This output is labeled on

the rear panel with ARC/OSD.

Connecting a CD Player or XLR Source

See Figure 7

Digital audio connection: Connect the digital output of the CD player to the

Optical or Coax digital inputs on the RSP-1576. Use the INPUT SETUP menu

to assign the audio input to the CD (the default is CD).

Analogue audio connections:

Option 1: Connect the left and right analog outputs from the CD player to

the AUDIO IN jacks labeled CD (left and right). This option uses the CD

player’s D/A converter. Depending on the selected DSP mode this connection

method may require the analog signal to be converted to a digital signal

for processing.

Option 2: If your CD Player (or another source) has XLR output connectors,

you can use the XLR inputs on the RSP-1576 for this connection. Connect the

left and right XLR outputs from the source to the jacks labeled BALANCED

INPUT (left and right). This option uses the CD player’s D/A converter.

Depending on the selected DSP mode this connection method may require

the analog signal to be converted to a digital signal for processing.

RSP-1576 Surround Sound Processor

Input Buttons 4qM

The input source can be changed by pressing the desired source input

buttons on the front panel or remote control.

SUR+ Buttons 9B

The SUR+ buttons on the remote control or front panel will display surround

mode information of currently selected source. The default DSP mode can

be congured in the Setup menu for each source. Press the SUR+ button

repeatedly to toggle through the available DSP modes.

DSP processing options vary depending on the selected source input type.

Not all DSP options are available in analog or digital input modes.

Other buttons on the remote can directly access specic DSP modes.

2CH: Changes the audio mode to STEREO, DOWN MIX.

BYPASS: Bypass all DSP processing.

PLCM: Selects Dolby ATMOS surround mode.

Playback Control buttons L

These buttons provide basic control functions for iPod AUDIO playback.

The control buttons can also control Rotel CD players. For more information

how to congure CD controls see the REMOTE CONTROL OVERVIEW

section of the manual. Supported functions include Play, Stop, Pause, Next

Track, Previous Track.

DIM Button J

Use this button to dim the front panel display.

Adjustment made using the

button is temporary only and not saved

after power off.

SUB, CTR, REAR Buttons B

These buttons can access the speaker setting and adjust the output level for

speakers in the system. Use the Up and Down arrow buttons on the remote

control to change values. This is only a temporary change. To make permanent

adjustments, please access the SPEAKER LEVEL SETUP menu from the OSD.

MEM Button E

This button does not operate with the RSP-1576 and is used only to control

a Rotel tuner product for preset memory control.

LIGHT Button N

Pushing this button turns on the back light of the remote control for easy

operation in dimly lit rooms.

ASSISTIVE LIGHT O

Push and hold on the LIGHT Button

for 3 seconds to turn on the assistive

light. This light can be used to help locate objects in a dimly lit room such

as a home theatre surrounding. The light will remain illuminated as long

as the button is held.

Automatic Surround Modes

Decoding of digital sources connected is generally automatic with detection

triggered by a “ﬂag” embedded in the digital recording telling the processor

what decoding format to use. For example, when a Dolby or DTS surround

signal is detected, the processor activates the proper decoding.

Remote Control Overview

The RSP-1576 is supplied with an easy to use remote control RR-CX100.

The RR-CX100 can be congured to use IR codeset 1 or IR codeset 2 in case

the unit is conicting with other Rotel models. Push and hold the TUNER

button and 1 (or TUNER and 2 for codeset 2) at the same time and hold for

approximately 5 seconds until the backlights on the remote control blink on

then off then release both buttons. This sets the remote control to use codeset

1 (or codeset 2 if TUNER and 2 are held). The System menu in the OSD

includes a conguration option to set the processor to either codeset 1 or

codeset 2. The factory default for the remote and processor is codeset 1.

The RR-CX100 can also control an attached Rotel CD player. The CD player

functions include Play, Stop, Pause, Track Forward, Track Back, Fast Forward,

Fast Reverse. To activate these functions press the CD button on the remote.

If the CD is attached to the XLR source input, these functions can be activated

by pressing the XLR button. To change the CD player functions to operate

after pressing the XLR button press and hold the XLR and 1 button for 5

seconds until the backlight LEDs blink twice times then release. To disable

XLR sending the CD control functions press and hold the XLR and 0 button

for 5 seconds until the backlight blinks.

The transport buttons will only operate for CD control after the CD or XLR

button is pressed on the remote. If a different input is selected from the

remote these buttons will no longer send the CD transport IR commands.

Overview of Buttons and Controls

This section provides a basic overview of the buttons and controls on the

front panel and the remote control. Detailed instructions on the use of these

buttons are provided in the more complete operating instructions in the

following sections.

STANDBY 1 and Power ON/OFF Buttons A

The front-panel STANDBY button and the remote control ON/OFF button

activate or deactivate the unit. The rear panel master POWER switch must

be on the ON position for the remote standby function to operate.

VOLUME Knob and VOLUME UP/DOWN Buttons =D

The VOLUME UP/DOWN buttons on the remote and the large rotary control

on the front panel provide the master VOLUME control, adjusting the output

level of all channels simultaneously including mute and volume level 1 to 96.

DISPLAY (DISP) Button 0B

Push this button to toggle through device status on the VFD and TV.

SETUP Button H

Navigating and ENTER Buttons

The SETUP button displays the OSD setup screen on the HDMI OSD enabled

output. Push the SETUP button again to deactivate this menu. Use the

navigation buttons Up/Down/Left/Right and ENTER on the remote control

to access the various menus.

MUTE Button -F

Push the MUTE button once to turn the sound off. An indication appears in

the front panel and on-screen display. Press the button again to restore the

previous volume level.

The processor will recognize a digital signal with Dolby Surround encoding

and activate Dolby

decoding. Additionally, you can conﬁgure a default

surround mode for each input using the INPUT SETUP menu (see the Setup

section of this manual). Combined with the auto-detection of Dolby Digital

and DTS, this default surround setting makes operation of the processor’s

surround modes totally automatic.

For stereo inputs such as CD and Tuner, you could select BYPASS or STEREO

mode as the default for 2-channel playback or a DSP mode if you prefer to

hear music sources in surround sound.

NOTE: A digital signal coming into the processor will be recognized and

properly decoded. However, on a Blu-ray with multiple soundtracks, you

may need to configure the player for the desired signal and encoding type.

For example, you may need to use the player’s menu system to select the

desired Dolby Digital or DTS soundtrack.

Manually Selecting Surround Modes

For users who prefer a more active role in setting surround modes, buttons

on the remote and the front panel provide manual selection of surround

modes that are not automatically detected or, in some cases, to override

an automatic setting.

Manual settings available from the front panel and/or the remote control

should be used when you want to play:

• Standard 2-channel stereo (Left/Right speakers, and depending upon

speaker settings also subwoofer) with no surround processing.

• Down mixed 2-channel playback of Dolby Digital 5.1 or DTS recordings.

• Dolby 3-channel stereo (Left/Right/center) of 2-channel recordings.

• 5-channel stereo, 7-channel, 9-channel or 11-channel from 2-channel

recordings.

• Other modes may be available depending on the system conguration

and active source material.

• PCM 2-channel (non 96kHz) digital signals can be overridden to Dolby

3-Stereo, 5CH Stereo, 7CH Stereo, 9CH, and 11CH and Stereo as

well as Dolby Atmos and DTS Neural:x.

To change the surround mode press the SUR+ button on the remote control

or front panel to toggle through the available options. The 2CH button on

the remote control will create a down mix of any multichannel signal to 2

channel stereo mode.

NOTE: Not all surround modes are available for all surround source

formats. The input source signal will determine the available surround

options that can be selected.

Digital Audio

You can play these recordings in BYPASS, 2-CH Stereo, Dolby 3-Stereo, 5-CH

Stereo, 7-CH Stereo, 9CH Stereo, 11CH Stereo, Dolby ATMOS Surround

and Dolby Neural:X modes.

All of the bass management settings (speaker size, subwoofer, and crossover)

are in effect with digital stereo inputs unless BYPASS mode is selected.

To change the surround mode press the SUR+ button on the remote control

or front panel control to toggle through the available surround options. The

2CH button on the remote control will create a down mix of any multichannel

signal to 2 channel stereo mode.

NOTE: Not all surround modes are available for all surround source

formats. The input source signal will determine the available surround

options that can be selected.

Analog Stereo

This type of recording includes any conventional stereo signals from the

processor’s analog inputs, including analog audio from CD players, FM

tuners, etc.

Analog stereo inputs require a choice about how the signal is routed through

the processor. One option is the ANALOG BYPASS mode. In this mode, the

stereo signal is routed directly to the volume control and the outputs. This

mode is pure 2-channel stereo, bypassing all of the digital circuitry. None

of the bass management features, speaker level settings, EQ settings, or

delay settings is active. There is no subwoofer output. A full-range signal is

sent directly to the front left and right speakers.

Alternatively, a DSP mode can be enabled, this converts the analog

inputs to digital signals, passing them through the digital processors in the

RSP-1576. This option allows all of the features to be active including bass

management settings, crossovers, subwoofer outputs, EQ settings, etc. There

are several DSP modes available including: 2-CH Stereo, Dolby 3-Stereo,

5-CH Stereo, 7-CH Stereo, 9CH and 11CH Stereo, Dolby ATMOS Surround

and Dolby Neural:X modes.

To change the surround mode press the SUR+ button on the remote control

or front panel control to toggle through the available surround options.

NOTE: Not all surround modes are available for all surround source

formats. The input source signal will determine the available surround

options that can be selected.

Basic Operation

This section covers the basic operating controls of the RSP-1576 and the

remote control.

Selecting Inputs

You can select any of the source inputs for listening and/or watching: VIDEO

1 - 7, CD, PHONO, XLR, MULTI INPUT, USB, PC-USB, BLUETOOTH or TUNER.

The source inputs can be customized using the INPUT SETUP menu to assign

which HDMI input to use as the video source. Video 1- 7 inputs can also

be congured to accept any analog and digital audio sources. The default

of audio source is set to HDMI Audio.

When you have congured the source input, you can use Input buttons to

select the desired inputs:

1. Press the Input buttons on the front panel 4q to switch to the selected

source input i.e. CD, Tuner, Video 1 etc...

2. Press the source input button on the remote control M to select the

desired source.

RSP-1576 Surround Sound Processor

USB/iPod Operation

iPod/iPhone Connection 5

1. An iPod/iPhone can be connected using the proper USB cable to the

USB front socket of the RSP-1576.

2. The iPod/iPhone will stream a digital music signal to the unit. Music

selection and playback control are available using the iPod/iPhone.

3. The iPod/iPhone screen will remain active while connected to the unit.

Playback Control Buttons L

Transport controls are available from the remote control during playback

including play, stop/pause, next track, previous track.

Bluetooth

Bluetooth Connection

The Bluetooth feature allows you to stream music wireless from your Bluetooth

enabled device, i.e. mobile phones. Select the BLUETOOTH (BT) input on

the RSP-1576. From your device (mobile phones etc.) activate Bluetooth and

allow it to search for other Bluetooth devices. Select “Rotel Bluetooth” and

connect to it. Once connected you can start streaming music to the RSP-1576.

NOTE: The RSP-1576 Bluetooth is APTX compatible. This enables you

to stream music at lossless CD quality.

NOTE: Some Bluetooth devices may require you to establish connection

again with the RSP-1576 if the unit was powered off. If this occurs,

please go through the above steps to re-connect.

Rear PC-USB

Rear PC-USB Connection

The rear USB socket labeled PC-USB accepts a type B USB plug. This input

accepts PCM audio signals sent from your computer up to 24 bits/192kHz

resolution.

Setup

The Rotel RSP-1576 features two types of information displays to help operate

the system. The ﬁrst consists of simple status displays that appear on the

TV screen whenever primary settings (Volume, Input, etc.) are changed.

A more comprehensive ON-SCREEN DISPLAY (OSD) menu system is available

at any time by pressing the SETUP H button on the remote. These OSD

menus guide you through the conﬁguration and setup of the RSP-1576. The

settings made in the conﬁguration process are memorized as default settings

and need not be made again for normal operation of the unit.

The OSD menus can be conﬁgured to display several different languages.

The default English version of all main menus are shown at the front of this

manual. If your language is available, those menus will be shown in the

instructions. If you would like to change from the default English language

before proceeding, go to the instructions for the SYSTEM SETUP menu later

in this manual. From this menu, you can change the language display.

Menu Basics

Navigation Buttons

The following remote control buttons are used to navigate the OSD menu

system:

SETUP button: Press to display the MAIN MENU. If a menu is already

visible, push this button to close the OSD and return to normal operation.

Up/Down buttons: Press to move up and down in the lists of menu items

that appear on the OSD screens.

Left/Right buttons: Press to change the current settings for a selected menu

item on OSD screens.

ENTER button: Press ENTER to conﬁrm a setting.

BACK Button: Press BACK to go back to the previous menu.

Main Menu

INPUT SETUP

SPEAKER CONFIGURATION

SPEAKER DISTANCE SETUP

SUBWOOFER SETUP

SPEAKER LEVEL SETUP

VIDEO SETUP

PEQ CONFIGURATION

SYSTEM SETUP

EXIT

AUDIO CONFIGURATION

MAIN MENU

The MAIN MENU provides access to OSD screens for various conﬁguration

options. MAIN MENU is reached by pressing the SETUP H button on the

remote. To select the desired menu, move the highlight using the Up/Down

arrow buttons and press the ENTER button on the remote control. Press the

SETUP button again or select “EXIT“ on the OSD to end setup and return

to normal operation.

Conﬁguring Inputs

A key step in setting up the unit, is to conﬁgure each source input using the

INPUT SETUP screens. Conﬁguring the inputs allows you to set defaults for a

number of settings including the type of input connector, the desired surround

mode, custom labels that appear in the displays when a source is selected,

and many more. The following OSD menus are used to conﬁgure the inputs.

Input Setup

SOURCE

NAME

VIDEO INPUT

AUDIO INPUT

TRIGGER OUTPUT

DEFAULT MODE

AUDIO DELAY

LEVEL ADJUST

BACK

INPUT SETUP

VIDEO 1

HDMI Audio

Mul Input

1 _ _

Source Dependent

0m sec

0dB

The INPUT SETUP menu conﬁgures the source inputs and is accessed from

the MAIN menu. The screen provides the following options, selected by

placing the highlight on the desired line using the Up/Down arrow buttons:

SOURCE: Changing this input allows you to select a specic input for

conguring (CD, TUNER, VIDEO 1–7, USB, PC-USB, XLR, PHONO, MULTI

INPUT and BLUETOOTH).

NAME: The name of the source can be customized. For example VIDEO1

can be named “TV” for easier reference. The default NAME is the same

as the SOURCE. Place the highlight on this option and press ENTER on the

remote control, it will then take you to the SOURCE NAME EDIT sub menu.

1. Press the Left/Right arrow buttons on the remote control to change the

ﬁrst letter, scrolling through the list of available characters.

2. Press the ENTER button on the remote control to conﬁrm that letter and

move to the next position.

3. Repeat steps 1 and 2 until all eight characters have been completed.

The ﬁnal press of the ENTER button saves the new name. Or select

the “

“ button on the screen to conrm if you have less than eight

characters to enter.

VIDEO INPUT: Selects the video source to be displayed on the TV monitor.

Assign the input to a source component you have connected by selecting

from HDMI 1–6 and HDMI Front. For audio only sources (such as a CD

player), you would typically specify OFF so that no video is displayed. The

video source can also be set to “Last Video Source” so when switching to

the specied Video input the previous Video source is not changed. This

feature is useful if you want to change only the audio and keep watching

whatever was the last displayed video source.

AUDIO INPUT: Assigns a physical input connection for the source displayed

in the ﬁrst line of the menu. Options include Optical 1–3, Coax 1–3, HDMI

Audio, Tuner, Multi Input, XLR, Phono, CD, Bluetooth, PC-USB, USB, ARC,

AUX or Off.

NOTE: Optical, Coaxial,CD and XLR inputs can be assigned to the

CD input source or Video 1-7. Audio input is not available to the XLR,

PHONO, MULTI INPUT, BLUETOOTH or USB input source.

When selecting the input source for “PC-USB”, AUDIO INPUT can be

changed to “USB Audio 1.0” or “USB Audio 2.0”. USB Audio Class 2.0

may require installation of the PC driver. For more information please see

PC-USB section in this manual.

TRIGGER OUTPUT: The RSP-1576 has three 12V trigger outputs (labeled 1

– 3) that supply a 12V DC signal to turn on other components as needed.

This menu item turns on speciﬁc 12V trigger outputs whenever the indicated

input source is selected. For example, congure the VIDEO 1 input to turn

on the 12V trigger for your DVD player. Any combination of trigger outputs

can be programmed for each source.

1. Place the highlight on the option “TRIGGER OUTPUT“ and press the

ENTER button on the remote control.

2. Press the Up/Down arrow buttons on the remote control to change the

ﬁrst position from blank to 1 (activating TRIGGER 1 for that source)

and use the Left/Right arrow buttons to move to the next position.

3. Repeat until all three positions are set as desired. The ﬁnal press of

the ENTER button conﬁrms the selection.

NOTE: The 12V trigger output 1 is defaulted to be turned on for all

input sources. You can turn it off by following the steps as above.

DEFAULT MODE: The DEFAULT MODE setting allows you to set a default

audio mode for each source input. The default setting will be used unless the

source material triggers automatic decoding of a particular type or unless

the default setting is temporarily overridden by the front panel or remote

surround mode buttons.

Options for the default surround modes are: Stereo, Dolby 3 Stereo, 5

channel Stereo, 7 channel Stereo, 9 channel Stereo, 11 channel Stereo,

Dolby ATMOS Surround, DTS Neural:X, Analog Bypass (for analog input

only) and Source Dependant.

NOTE: Most types of digital discs or source material are generally

detected automatically and the proper decoding activated with no

action or setting required.

Since Dolby and DTS sources are detected and decoded automatically, the

default setting typically tells the unit how to process a 2-channel stereo signal.

For example, you might have your CD input default to 2-channel stereo, DVD

and game console inputs default to Dolby processing for surround material,

and TUNER input default to 5 Channel Stereo mode.

In some cases, the default setting can be manually overridden by the 2CH,

BYPASS and SUR+ button on the remote control or front panel, or PLCM button

on the remote control. See the Manually Selecting Surround Modes section

of this manual for more information on which settings can be overridden.

AUDIO DELAY: Also known as “lip-sync” delay, this setting delays the audio

signal for an input by the speciﬁed amount to match the video input. This

feature can be useful when the video signal is delayed more than the

audio signal.

The range of available settings is from 0 ms to 500 ms, in 10 ms steps. The

setting is individually stored for each input and is the default Audio Delay

each time that input is selected.

LEVEL ADJUST: Use this feature to set the volume level lower than the other

inputs. This feature is useful for sources that are consistently higher in volume

than other sources in the system.

Valid settings include: 0 to -6 dB, in 0.5 dB steps.

RSP-1576 Surround Sound Processor

FIXED VOLUME: Congures a Fixed Volume level for a specied input. To

enable this feature, select the desired xed volume level for USB, PC-USB,

Bluetooth, Coax 1 or Optical 1. When enabled and the input with a Fixed

Volume is selected, the Volume level will immediately be set to the specied

level. Fixed volume: Variable is factory default.

Valid settings include: Variable, 1 - 96.

NOTE: The Volume knob on the front panel and Volume +/- buttons

on the IR remote are disabled when the volume is Fixed. To disable this

feature set the Fixed Volume level to “Variable”.

Press the SETUP button on the remote control to exit the menu and return

to normal operation.

Multi Input Setup

SOURCE

NAME

VIDEO INPUT

TRIGGER OUTPUT

LEVEL ADJUST

BACK

INPUT SETUP

MULTI INPUT

M-INPUT

HDMI1

1 _ _

0dB

When the MULTI INPUT source is selected on the INPUT SETUP menu, the

available options change to reﬂect the fact that these inputs are direct analog

inputs and bypass the unit’s digital processing. The AUDIO INPUT, DEFAULT

MODE and AUDIO DELAY options are not available since these functions

are processed digitally and not available to the MULTI INPUT source.

Conﬁguring Audio

Audio Conguration

FRONT

CENTER

SURROUND

SUBWOOFER

CENTER BACK

HEIGHT 1

HEIGHT 2

BACK

CONFIGURATION

AUDIO CONFIGURATION

Front

Center

Surround

Subwoofer

Center Back

Overhead Front

Overhead Rear

7.1.4

The AUDIO CONFIGURATION menu conﬁgures the preamplier RCA outputs.

The screen provides options from 5.1 to 7.1.4 and an option for 5.1 with

Bi-Amplication. After selecting the desired conguration, the preamplier

RCA output audio signal connections are displayed for up to 12 channels.

Conﬁguring Speakers and Audio

This section of the setup process covers items concerning audio reproduction

such as the number of speakers, bass management including subwoofer

crossovers, establishing equal output levels for all channels, delay settings,

and parametric EQ.

Understanding Speaker Conﬁguration

Home theater systems vary in the number of speakers and the bass capabilities

of those speakers. This processor offers surround modes tailored to systems

with various numbers of speakers and bass management features which send

bass information to the speaker(s) best able to handle it – subwoofers and/

or large speakers. For optimum performance, you must tell the processor

the number of speakers in your system and how bass should be distributed

among them.

The following conﬁguration instructions refer to LARGE and SMALL speakers,

referring more to their desired bass conﬁguration than their physical size.

Specically, use the LARGE setting for speakers that you want to play deep

bass signals. Use the SMALL designation for speakers that would beneﬁt

from having their bass sent to more capable speakers. The bass management

system redirects bass information away from all SMALL speakers and sends

it to the LARGE speakers and/or the SUBWOOFER. It may be useful to think

of LARGE as “full-range” and SMALL as “high-pass ﬁltered.”

• Five LARGE speakers and subwoofer: This system requires no bass

redirection. All ﬁve speakers play the normal bass recorded in their

respective channels. The subwoofer plays the normal channel bass.

Meanwhile the normal bass places higher demands on the capabilities

of the other speakers and the ampliers driving them.

• LARGE front, center, surround speakers, no subwoofer: The normal

bass from the front, center, and surround channels is played in its

respective speakers.

• All SMALL speakers and subwoofer: The normal bass from all channels

is redirected to the subwoofer. The subwoofer handles ALL of the bass

in the system. This conﬁguration provides several beneﬁts: deep bass

is played by the speaker most suited to do so, the main speakers may

play louder with less distortion, and the need for amplier power is

reduced. This conﬁguration should be used with bookshelf-size or

smaller main speakers. It should also be considered in some cases

with ﬂoorstanding front speakers. This conﬁguration is advantageous

when driving the system with moderate power ampliers.

• LARGE front speakers, SMALL other speakers, and a subwoofer: The

normal bass from the SMALL center and surround speakers is redirected

to the LARGE front speakers and the subwoofer. The LARGE front

speakers play their own normal bass plus the redirected bass from

the SMALL speakers. The subwoofer plays the redirected bass from

all of the other channels. This might be an appropriate conﬁguration

with a pair of very capable front speakers. A potential disadvantage

with mixed LARGE and SMALL congurations is that the bass response

may not be as consistent from channel to channel as it might be with

the all SMALL conﬁguration.

Speaker Conguration

FRONT

CENTER

SURROUND

SUBWOOFER

OVERHEAD REAR

ADVANCED SETUP

BACK

CENTER BACK

OVERHEAD FRONT

SPEAKER CONFIGURATION

Large

Small

Yes

None

The SPEAKER CONFIGURATION menu is used to conﬁgure the RSP-1576 for

use with your speciﬁc loudspeakers and to determine the bass management

conﬁguration as described in the previous overview. The menu is accessed

from the MAIN menu. The Audio Conguration will determine which speakers

are displayed in the Speaker Conguration menu.

The following speaker options are available:

FRONT SPEAKERS (Small/Large): Use the “Large” setting to have the front

speakers play low bass (full-range). Use the “Small” setting to redirect

normal bass away from these speakers to a subwoofer (high-pass ﬁltered).

CENTER SPEAKER(S) (Large/Small/None): Select the “Large” setting (not

available with SMALL front speakers) to have the center speaker play low

bass (full-range). Select the “Small” setting if your center channel speaker

has limited low frequency capability, or if you prefer that the bass be sent

to the subwoofer (high-pass). Select the “None” setting if your system does

not have a center channel speaker (the surround modes will automatically

divide all center channel information equally between the two front speakers,

creating a phantom center channel).

SURROUND SPEAKERS (Large/Small/None): Select the “Large” setting (not

available with SMALL front speakers) to have the surround speakers play

low bass (full-range). If your rear speakers have limited bass capability

or if you would prefer that the bass go to a subwoofer, select the “Small”

setting (high-pass). If your system has no rear surround speakers, select the

“None” setting (surround channels are added to the front speakers so none

of the recording is lost).

SUBWOOFER (Yes/Max/No): The “Yes” setting is the standard setting if your

system has a subwoofer. If your system does not have a subwoofer, select

“No”. Select the “Max” setting for maximum bass output with normal bass

being duplicated by both the subwoofer and any LARGE speaker in the system.

CENTER BACK (1Large/1Small/2Large/2Small/None): Some systems have

one or two additional center back surround speakers. Select the “Large”

setting (not available with SMALL front and surround speakers) to have

your center back speaker(s) play low bass. Use “1Large” if you have one

center back speaker (6.1) or “2Large” (7.1) if you have two center back

speakers (7.1). If your center back speakers have limited bass capability or

if you would prefer that the bass go to a subwoofer, use the “Small” setting

(“1Small” for one speaker, “2Small” for two speakers). If your system has

no center back speakers, select the “None” setting.

OVERHEAD FRONT (Large/Small/None): Select the “Large” setting (not

available with SMALL front and surround speakers ) to have your overhead

front speakers play low bass. If you would prefer that the bass go to a

subwoofer, use the “Small” setting.

OVERHEAD REAR (Large/Small/None): Select the “Large” setting (not

available with SMALL front , top front and surround speakers ) to have your

overhead rear speakers play low bass. If you would prefer that the bass go

to a subwoofer, use the “Small” setting.

ADVANCED: Speaker conﬁguration is generally a global setting for all surround

modes and need only be done once. However, for special circumstances,

the processor provides the option of setting the speaker conﬁguration

independently for each surround mode. Select the ADVANCED SETUP line

on the menu and press ENTER to go to the ADVANCED SPEAKER SETUP

menu described in the following section.

To change a setting on the SPEAKER CONFIGURATION menu, place the

highlight on the desired line using the Up/Down arrow buttons and use the

Left/Right arrow buttons to toggle through the available settings. To return to

the MAIN menu, select “BACK” on the OSD and press the ENTER button,

or press the BACK button. Press the SETUP button, or select “EXIT” on the

OSD to exit setup and return to normal operation.

Advanced Speaker Setup

SPEAKER

CROSSOVER

DOLBY

DTS

STEREO

BACK

ADVANCED SPEAKER SETUP

Front

100Hz

Default

In most cases, the standard speaker conﬁguration described above is a global

setting and can be used for all surround modes. However, the processor

provides the capability to customize these settings for three different modes:

Dolby, DTS, and Stereo. In addition, the ADVANCED SPEAKER SETUP

allows you to select a customized high-pass crossover frequency for the

front, center, surround, surround back speakers.

NOTE: In most systems, the default settings on this menu will provide

the most predictable results and most users will not need to change

any settings. You should fully understand bass management and have

a speciﬁc reason for needing a custom conﬁguration before changing

these settings. Otherwise, skip to the following topic, SUBWOOFER

SETUP.

The available settings on the ADVANCED SPEAKER SETUP menu are as follows:

SPEAKER (Front/Center/Surround/Center back/Overhead Front/Overhead

Rear/Subwoofer): Select the set of speakers to be conﬁgured with custom

settings.

CROSSOVER (40Hz/50Hz/60Hz/70Hz/80Hz/90Hz/100Hz/120Hz/150Hz

/200Hz/OFF): This setting for the high-pass and low-pass crossover point is

only active for SMALL speakers settings and the subwoofer. When you ﬁrst

access the ADVANCED SPEAKER SETUP menu, the current crossover point

will be shown on this line which is set to “100Hz” as the factory default.

Change the value of this line only if you want the current speaker to have a

different crossover point. This setting ONLY affects redirected bass.

NOTE: The “OFF” setting (available only for the subwoofer) sends

a full-range signal to your subwoofer so that you can use its built-in

low-pass filter.

NOTE: When a speaker is set to “Large” on the SPEAKER

CONFIGURATION menu or on this menu, the crossover setting has no

effect since, by deﬁnition, a LARGE speaker plays full-range with no

bass redirection to the subwoofer and no crossover. In addition, the

CROSSOVER setting is not available for the MULTI INPUT.

DOLBY (Default/Large/Small/None): Sets the current speaker (shown in the

ﬁrst line) to Large, Small, or None, overriding the setting from the SPEAKER

SETUP menu. If you want to use the speaker size setting set in the SPEAKER

RSP-1576 Surround Sound Processor

SETUP menu, select “Default”. The “None” setting is not available for

FRONT speakers.

DTS (Default/Large/Small/None): The same options described for Dolby

above, except these settings ONLY take effect with DTS decoding.

STEREO (Default/Large/Small/None): The same options described for Dolby

above, except these settings ONLY take effect in STEREO surround mode.

For the subwoofer, the above selections for DOLBY, DTS, and STEREO

become “Yes/No/Default”. They will be set to “Default” if the front speakers

are set to “Default”, and they would be set to “Yes” if the front speakers

are set to “Small”.

NOTE: When the front speakers are set to use the default settings on

the ADVANCED SPEAKER SETUP menu, the speciﬁc “Large/Small/

None” settings of DOLBY, DTS or STEREO are not available for the

other speakers. These speakers will use the default settings.

Subwoofer Setup

DOLBY

STEREO

MULTI LPCM

MULTI INPUT

BACK

SUBWOOFER SETUP

DTS

0dB

These five lines allow you to override the subwoofer level setting as

determined in the Speaker Level Setup menu (see next section) for each

specic surround mode.

DOLBY

DTS

STEREO

MULTI LPCM

MULTI INPUT

Use the Up/Down arrow buttons to move to the specic surround mode and

use the Left/Right arrow buttons to adjust the subwoofer level for the current

surround mode. The options are a range of adjustments from -9 dB to +9

dB and MAX (+10 dB). A setting of 0 dB means that the speciﬁed surround

mode will use the master subwoofer level. Any other setting is an offset to

the master setting. For example, an adjustment of -2 dB for a particular

surround mode means that the subwoofer level will be 2 dB quieter than

the master subwoofer level when that surround mode is selected. Use these

subwoofer level settings to adjust the relative bass output of various surround

modes. Changing the master subwoofer level will increase or decrease the

level for all surround modes.

We recommend starting with the settings for all surround modes at the

default 0 dB setting during the speaker level calibration of the system and

for a period of familiarization after that. As you listen to a variety of source

material over time, you may notice that certain surround modes consistently

produce too much or too little bass from the subwoofer. If so, then use these

menu settings to customize each surround mode. In general, if the master

subwoofer level is set properly (i.e. not too loud), individual settings for

each surround mode should not be necessary.

To return to the main menu select “BACK” on the OSD or push the BACK

button on the remote control.

Speaker Level Setup

FRONT LEFT

CENTER

FRONT RIGHT

SURROUND RIGHT

CENTER BACK RIGHT

CENTER BACK LEFT

SURROUND LEFT

SUBWOOFER

BACK

OVERHEAD FRONT RIGHT

OVERHEAD REAR RIGHT

OVERHEAD REAR LEFT

OVERHEAD FRONT LEFT

SPEAKER LEVEL SETUP

0dB

NOTE: If you have conﬁgured your system to use two center back

speakers, there will be an additional line in the menu, giving you the

ability to independently adjust the CENTER BACK LEFT and CENTER

BACK RIGHT speakers.

This menu uses ﬁltered pink noise test tones to set equal volume levels for

all speakers (FRONT LEFT, CENTER, FRONT RIGHT, SURROUND RIGHT,

CENTER BACK RIGHT, CENTER BACK LEFT, OVERHEAD FRONT RIGHT,

OVERHEAD REAR RIGHT, OVERHEAD REAR LEFT, OVERHEAD FRONT LEFT,

SURROUND LEFT and SUBWOOFER) to ensure proper surround sound

reproduction. Setting the output levels using the test procedure provides the

most accurate adjustment so that digital surround sound material will be

reproduced as it was intended and is a critical step in calibrating the system.

The Audio Conguration will determine which speakers are displayed in

the Speaker Level Setup menu.

When you enter the SPEAKER LEVEL SETUP menu, you will hear a test tone

coming from the highlighted speaker. Highlight different speakers by moving

the cursor to the desired line using the Up/Down arrow buttons. The test

tone will shift accordingly to the selected speaker.

Seated in the normal listening location, shift the test tone to the various

speakers. Using the one speaker as a reference, listen for any speakers that

are noticeably louder or quieter. If so, adjust that speaker’s levels up or down

(in 0.5 dB increments) using the Left/Right arrow buttons. Continue switching

among the speakers and adjusting until all speakers are the same volume.

To return to the MAIN menu, select “BACK“ on the OSD or press the BACK

button. Press the SETUP button or select “EXIT“ on the OSD to exit setup

and return to normal operation.

Calibration with an SPL meter:

Calibrating the system with an SPL (Sound Pressure Level) meter, rather than

by ear, provides more precise results and improves the system’s performance

signicantly. Inexpensive SPL meters are widely available and the procedure

is quick and easy.

Both Dolby and DTS specify a standard calibration level for all theaters

to ensure that soundtracks can be played at the volume level intended by

the director of the ﬁlm. This reference level should result in spoken dialog

played at a realistic level for normal speech with the loudest peaks in any

single channel at about 105 dB. The RSP-1576’s test tones are generated at

a precise level (-30 dBFs) relative to the loudest possible digitally recorded

sound. At the Dolby or DTS reference level, these test tones should produce

a 75 dB reading on an SPL meter.

Set the meter to its 70 dB dial setting with SLOW response and C-weighting,

held away from your body at your listening position (mounting the SPL

meter on a camera tripod makes this easier). You can point the SPL meter

at each speaker as it is being measured; however, positioning the meter

in a ﬁxed position pointing at the ceiling is easier and probably produces

more consistent results.

Increase the master volume control on the unit until the meter reads 75 dB

(+5 dB on the meter scale) when playing the test tone through one of the

front speakers. Then, use the individual channel adjustments on the SPEAKER

LEVEL SETUP menu to adjust each of the individual speakers, including the

subwoofer, to the same 75 dB on the SPL meter.

NOTE: Due to meter weighting curves and room effects, the actual

level of the subwoofer may be slightly higher than you measure. To

compensate, Dolby suggests setting the subwoofer several dB lower

when calibrating with an SPL meter (i.e. set the subwoofer to read 72

dB on the meter instead of 75 dB). Ultimately, the proper subwoofer

level must be determined by personal taste and some listeners prefer

to set it above 75 dB for ﬁlm soundtracks. Exaggerated bass effects

come at the expense of proper blending with the main speakers and

place stress on the subwoofer and its amplifier. If you can localize

bass from the subwoofer, the subwoofer level may be too high. Music

can be useful for ﬁne-tuning the subwoofer level as excessive bass is

readily apparent. The proper setting will generally work well for music

and movie soundtracks.

Remember the setting of the master volume control used during this calibration.

To play a Dolby Digital or DTS soundtrack at the reference volume level,

simply return to that volume setting. Note that most home theater listeners

ﬁnd this setting to be excessively loud. Let your own ears be the judge for

deciding how loud to playback movie soundtracks and adjust the master

volume control accordingly. Regardless of your listening levels, using an SPL

meter to calibrate equal levels for all speakers in the system is recommended.

Speaker and Delay/Distance Setup

FRONT LEFT

CENTER

FRONT RIGHT

SURROUND RIGHT

CENTER BACK RIGHT

CENTER BACK LEFT

SURROUND LEFT

SUBWOOFER

BACK

OVERHEAD FRONT RIGHT

OVERHEAD REAR RIGHT

OVERHEAD REAR LEFT

OVERHEAD FRONT LEFT

SPEAKER DISTANCE SETUP

10.00 FT 3.05M

The SPEAKER DISTANCE SETUP menu, which is reached from the MAIN

menu, allows you to set the delay for individual speakers. This ensures that

the sound from each speaker arrives simultaneously at the listening position,

even when the speakers are not all placed at equal distances from the

listener. Increase the delay to speakers located closer to the seating area

and decrease the delay to speakers located farther from the seating area.

The Audio Conguration will determine which speakers are displayed in

the Speaker Distance Setup menu.

This Rotel processor makes setting the delay time for each speaker very

easy. Simply measure the distance (in feet or meters) from your seating

position to each speaker in your system. Set the measured distance in the

line for each speaker. The menu provides a line for each speaker conﬁgured

in your system and gives a range of settings up to 33 feet (10.06 meters)

in 0.25 foot (0.075 m) increments with each increment equivalent to an

additional delay of 0.25 ms.

To change a setting, place the highlight on the desired line using the Up/

Down arrow buttons and use the Left/Right arrow buttons to increase or

decrease the delay. To return to the MAIN menu, press the BACK button or

select “BACK“ on the OSD. Press the SETUP button or select “EXIT“ on the

OSD to exit setup and return to normal operation.

Miscellaneous Settings

System Setup

LANGUAGE

IR REMOTE CODESET

PEQ FUNCTION

DISPLAY

NETWORK CONFIGURATION

SOFTWARE INFORMATION

RESTORE FACTORY DEFAULT

BACK

POWER OPTION

SYSTEM SETUP

English

Codeset 1

Disable

HDMI And VFD

This SYSTEM SETUP menu, reached from the MAIN menu, provides access

to several miscellaneous settings as follows:

LANGUAGE: Selects a language for the On Screen Display.

IR REMOTE CODESET: The RSP-1576 has two IR codesets and can be changed

in the event there is a conict of IR codes with other Rotel products.

NOTE: After changing the IR REMOTE CODESET the remote must

also be changed to continue using the remote control. Push and hold

the TUNER button and 1 (or TUNER and 2 for codeset 2) at the same

time and hold for approximately 5 seconds until the backlights on the

remote control blink on then off then release both buttons. This sets the

remote control to use codeset 1 (or codeset 2 if TUNER and 2 are held).

PEQ FUNCTION: Turns the PEQ function On or Off.

DISPLAY: Sets the information shown on the main HDMI OSD and front VFD

display. Settings are “Off”, “HDMI Only”, “VFD Only“ or “HDMI And VFD”.

POWER OPTION: Access to conguration of Off Timer, Max Power On

Volume, Power Mode and Signal Sense Input.

OFF TIMER

BACK

SIGNAL SENSE INPUT

POWER MODE

POWER OPTION

20 MINS

Disable

Normal

MAX POWER ON VOLUME 45

RSP-1576 Surround Sound Processor

OFF TIMER: Set the amount of time the units stays powered on when there

is no audio signal. The RSP-1576 will automatically go to standby mode

if audio is not detected for the specied timer period. Default: 20 MINS.

Valid settings include: Disable, 20 MINS, 1 Hour, 2 Hours, 4 Hours.

MAX POWER ON VOLUME: Species the maximum volume level to be

used each time the unit powered on. Valid settings include: 20 - 70.

Default: 45.

POWER MODE: Enables the rear panel USB power port to remain

powered at all times. The power consumption is higher in Quick Power

mode. To enable continuous power to the rear USB power port select

the Quick option.

Valid settings include: Normal, Quick.

NOTE: When the POWER MODE is configured to Quick, the RSP-1576

will consume additional power in standby mode.

SIGNAL SENSE INPUT: Checks if a digital audio signal is present on

the congured Signal Sense Input. When this input is selected as the

active listening source, the RSP-1576 monitors the digital data stream to

determine if there is audio. If there is no audio detected for 10 minutes,

the RSP-1576 will enter Signal Sense Standby Mode. When in Signal

Sense Standby Mode and the RSP-1576 detects audio on Signal Sense

Input, the unit will automatically power on. To disable this function, select

the DISABLE option which is the factory default setting.

NOTE: The Signal Sense function is not available if Standby Video

Source is enabled.

NOTE: When the RSP-1576 enters standby mode via the remote

control, the Signal Sense function will not operate until the unit detects

the audio has stopped for the minimum 10 minute time-out period. This

prevents the unit from immediately powering back on if there is still

active audio playing.

NOTE: When the SIGNAL SENSE INPUT function is activated, the

RSP-1576 will consume additional power in signal sense standby mode.

NETWORK CONFIGURATION: Sets the network conguration for the unit. In

most systems, set the IP ADDRESS MODE to DHCP. This setting will allow

your router to assign an IP address to the RSP-1576 automatically. If your

network uses xed IP addresses, set the IP ADDRESS MODE to Static. A

xed or STATIC IP address requires manually entering the IP Address, Subnet

Mask, Gateway, and DNS in the IP ADDRESS CONFIGURATION sub menu.

IP ADDRESS MODE

VIEW NETWORK SETTINGS

TEST NETWORK CONNECTION

BACK

NETWORK CONFIGURATION

RENEW DHCP IP ADDRESS

DHCP

SOFTWARE INFORMATION: Displays the current software installed in the

unit. It shows the MAIN, DSP and STANDBY software versions. There is also

an option to check for software updates. This feature lets the unit search

for software updates on the Internet. The network needs to be properly

congured. Alternatively, you can load the software through the front USB

socket. For more information on the software update process please contact

your authorized Rotel dealer.

RESTORE FACTORY DEFAULT: This option sets the unit back to the original

setting as when it left the factory. All user settings will be erased.

NOTE: Use caution when resetting the RSP-1576 to factory defaults

as all user configured options will be erased and reset to original

factory settings.

Video Setup

STANDBY VIDEO SOURCE

FAST AUDIO SYNC

VIDEO SETUP

Disable

OSD FORMAT

BACK

480P

Disable

The VIDEO SETUP menu provides conﬁguration of the HDMI outputs. See

the HDMI INPUTS & OUTPUTS section of this manual for details on HDMI

connections.

STANDBY VIDEO SOURCE: Options are “Disable”, “HDMI 1-6”, “HDMI

Front”, or “Last”. This allows the selected HDMI source input to pass-through

the RSP-1576 while in standby mode. Audio and video are passed directly

to the attached TV or display.

NOTE: When the Standby Video Source is enabled the RSP-1576 will

consume additional power when in standby mode.

NOTE: Signal Sense power control is disabled with STANDBY VIDEO

SOURCE is enabled.

FAST AUDIO SYNC: This function allows the HDMI audio to sync more

quickly with the RSP-1576. Only 1 input can be selected for this function.

NOTE: Some source devices do not provide the timing requirements to

allow this function to work properly and could result in static noise before

the audio is heard.

OSD FORMAT: The HDMI On Screen Display output resolution can be

changed from 480p to 576p. The default value is 480p.

Press the BACK button or select “BACK“ on the OSD to exit the VIDEO

SETUP Menu and return to the main menu.

PEQ Conguration

SPEAKER : Front Le

FREQUENCY : 20Hz

FREQUENCY : 40Hz Q : 1 GAIN : 0

FREQUENCY : 60Hz Q : 1 GAIN : 0

FREQUENCY : 120Hz Q : 1 GAIN : 0

FREQUENCY : 200Hz Q : 1 GAIN : 0

FREQUENCY : 500Hz Q : 1 GAIN : 0

FREQUENCY : 1200Hz Q : 1 GAIN : 0

FREQUENCY : 4000Hz Q : 1 GAIN : 0

FREQUENCY : 12000Hz Q : 1 GAIN : 0

FREQUENCY : 20000Hz

Q : 1

PEQ CONFIGURATION

BACK

GAIN : 0

Q : 1

The PEQ CONFIGURATION menu allows you to enter EQ values for 10

bands as shown. PEQ setup requires advanced knowledge and equipment

for measuring the frequency response of the room and performance of the

speakers. To properly congure the EQ you should be familiar with the

tools and equipment needed. Typically these settings are only changed

by professional installers to ensure optimal performance of the RSP-1576.

Use the navigation buttons to highlight the frequency: Push the ENTER

button on the remote control to access and make changes. Use the Up/

Down arrow buttons to change the value. Use the Left/Right arrow buttons

to move to the next section on the line. Press ENTER again to conrm settings

and allow navigation to the next PEQ BAND. The Audio Conguration

will determine which speakers are available for conguration in the PEQ

Conguration menu.

FREQUENCY: There are 10 bands available and the frequency can be

changed between 10 - 24kHz as below.

BAND 1 Freq: 10Hz - 40Hz, 1Hz Step Default 20Hz

BAND 2 Freq: 20Hz - 44Hz, 1Hz Step Default 40Hz

BAND 3 Freq: 45Hz - 89Hz, 1Hz Step Default 60Hz

BAND 4 Freq: 90Hz - 180Hz, 10Hz Step Default 120Hz

BAND 5 Freq: 190Hz - 350Hz, 10Hz Step Default 200Hz

BAND 6 Freq: 360Hz - 690Hz, 10Hz Step Default 500Hz

BAND 7 Freq: 700Hz - 1900Hz, 100Hz Step Default 1.2kHz

BAND 8 Freq: 2kHz - 7.78kHz, 100Hz Step Default 4kHz

BAND 9 Freq: 8kHz - 20kHz, 100Hz Step Default 12kHz

BAND 10 Freq: 8kHz - 24kHz, 100Hz Step Default 20kHz

Q: The Q value can be adjusted between 1 to 10.

GAIN: The gain can be set between -12 to +2.

To exit this menu press the BACK button or select “BACK“ on the OSD then

press the SETUP button to return to normal operations.

NOTE: Q in EQ value relates to the bandwidth of the filter. The higher

the value, the narrower the bandwidth.

Troubleshooting

Most difculties in audio systems are the result of incorrect connections, or

improper control settings. If you encounter problems, isolate the problem

area, check the control settings, determine the cause of the fault and make

the necessary changes. If you are unable to get sound from the unit, refer

to the suggestions for the following conditions:

The unit does not turn on

• Make sure the power cord is plugged into the rear panel and a AC outlet.

• Make sure the rear panel POWER switch is in the ON position.

No sound from any input

• Make sure that MUTING is off and VOLUME is turned up.

• Make sure source inputs are connected and conﬁgured correctly.

No sound from digital sources

• Make sure that digital input connector is assigned to the proper source

input and that the source input is conﬁgured to use the digital input

rather than an analog input.

• Check the conﬁguration of the digital input source player to ensure

that the digital output is activated.

No sound from some speakers

• Check all power amp and speaker connections.

• Check Speaker Conﬁguration settings in the Setup menus.

No Video Output

• Make sure that the TV monitor is connected properly and check the

input assignments.

• Check the source input and TV output resolution are compatible. A 4K

source can only be sent to a 4K monitor.

• HDMI cables must be 5 meters or less in length.

• If watching 3D sources, make sure the display is 3D enabled.

Video and Audio do not match.

• Check that the proper video source is selected for each input.

• Check that the group delay (lip-sync) setting is not mis-adjusted.

Clicking or popping sounds when switching inputs

• The unit uses relay switching to preserve maximum sound quality. The

mechanical clicking of the relays is normal.

• Switching between HDMI sources may cause delays as HDMI two way

communications “handshake” must be established between the source

and display. The time required for the handshake varies depending

on the attached equipment.

RSP-1576 Surround Sound Processor

Controls do not operate

• Make sure that fresh batteries are installed in the remote.

• Make sure that the IR sensor on the front panel is not blocked. Aim the

remote control at the sensor.

• Make sure the sensor is not receiving strong IR light (sunlight, halogen

lighting, etc.).

• Unplug the unit from the AC outlet, wait 30 seconds, and plug it

back to reset.

• Conrm the IR Codeset set in the remote control and RSP-1576 are

matched to either Codeset 1 or Codeset 2.

Specications

Audio

Total Harmonic Distortion 0.0006% (Analog Bypass)

0.003% (Digital Input)

Intermodulation Distortion (60 Hz : 7 kHz, 4:1) < 0.005%

Frequency Response

Phono Input 20 Hz - 20k Hz, ± 0.5 dB

Analog Bypass 10 Hz - 100k Hz, ± 1 dB

Digital Input 20 Hz - 20k Hz, ± 0.5 dB

Signal to Noise Ratio (A-weighted)

Analog Bypass 112 dB

Digital Input 112 dB

Input Sensitivity/Impedance

Phono Level 3.5 mV / 47k ohms

Line Level 270 mV / 100k ohms

Balance Level 500 mV / 100k ohms

Preamp Output Level

Line Level 1.0 V

Channel Separation (at 10k Hz) > 75 dB

Digital Audio LPCM (up to 192kHz, 24-bit)

Dolby

Surround,

Dolby

TrueHD,

Dolby

ATMOS,

DTS-HD Master Audio,

DTS X

Video

Input Resolutions 480i/576i, 480p/576p, 720p,

1080i, 1080p, 1080p 24Hz,

3D, 4K, UHD, 4K 60Hz, 4K HDR10

Output Resolution 480i/576i, 480p/576p, 720p

1080i, 1080p, 1080p 24Hz,

3D, 4K, UHD, 4K 60Hz, 4K HDR10

Color Space Support sRGB, YCbCr 4:2:2, YCbCr 4:4:4

Deep Color Support 24-bit, 30-bit, 36-bit

HDMI Inputs/Outputs 7 inputs supporting HDCP 2.2, HDMI2.0a

2 outputs supporting HDCP 2.2, HDMI2.0a

Audio Return Channel

General

Power Consumption 60 watts

< 0.5 watt (standby)

Power Requirements (AC) 120 volts, 60Hz

230 volts, 50Hz

BTU 114 BTU/h

Dimension (W x H x D) 431 x 144 x 348 mm

17 x 5

/3 x 13

/7 in

Front Panel Height 3U / 132.6 mm / 5

/4 in

Weight 8.8 kg / 19.4 lbs

All specifications are accurate at the time of printing.

Rotel reserves the right to make improvements without notice.

Rotel and the Rotel Hifi logo are registered trademarks of The Rotel Co., Ltd. Tokyo, Japan.

“Made for iPod,” and “Made for iPhone,” means that an electronic accessory

has been designed to connect specically to iPod or iPhone, respectively, and

has been certied by the developer to meet Apple performance standards. Apple

is not responsible for the operation of this device or its compliance with safety

and regulatory standards. Please note that the use of this accessory with iPod,

or iPhone may affect wireless performance.

iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple

Inc., registered in the U.S. and other countries.

Français

Vue d’ensemble de la télécommande . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Vue d’ensemble des touches et des commandes ............................38

Touche STANDBY 1 et Touche POWER ON/OFF A 38

Bouton de VOLUME et Touche VOLUME UP/DOWN =D 38

Bouton AFFICHAGE (DISP) 0B 38

Bouton Conguration (Setup) H 38

Touches de Navigation et de Sélection (FONCTION) I 38

Touche MUTE -F 38

Touches INPUT 4qM 38

Touche SUR+ 9B 38

Touches de commandes pour la lecture L 38

Bouton DIM J 38

Boutons SUB, CTR et REAR B 38

Touche MEM E 38

Touche LIGHT N 38

Touche ASSISTIVE LIGHT O 38

Modes surround automatiques ........................................38

Sélection manuelle des modes surround ..................................38

Audio numérique stéréo 39

Stéréo analogique 39

Fonctions de base ..................................................39

Sélection des entrées 39

Fonctionnement USB/iPod ...........................................39

Connexion d’un iPod ou d’un iPhone 5 39

Boutons de lecture L 40

Bluetooth. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Connexion Bluetooth 40

Prise USB arrière ..................................................40

Connexion à la prise USB arrière 40

Réglages et conguration ............................................40

Menus de base ....................................................40

Touches de navigation 40

Menu Principal (Main Menu) 40

Conguration des Entrées ............................................40

Conguration des Entrées (Input Setup) 41

Conguration de l’entrée Multi 42

Conguration de la partie audio .......................................42

Conguration audio 42

Conguration des Enceintes et de la partie Audio ...........................42

Conguration des enceintes 43

Conguration Avancée des Enceintes 44

Conguration du caisson de graves 44

Réglage des niveaux des enceintes 45

Réglage des distances des enceintes 46

Réglages Divers ...................................................46

Conguration Système (System Setup) 46

Conguration Vidéo 47

Egalisation PEQ 48

Résolution des pannes ..............................................48

Spécications .....................................................49

Sommaire

Schéma 1 : Commandes et Connexions 5

Schéma 2 : Télécommande 6

Schéma 3 : Amplicateurs et caissons de graves 7

Schéma 4 : Connexions audio numériques et PC-USB 8

Schéma 5 : Connexions à un lecteur Blu-Ray ou Vidéo 8

Schéma 6 : Connexions USB en face avant 9

Schéma 7 : Connexions à un lecteur de CD 9

Schéma 8 : Connexions à un tuner 10

Schéma 9 : Connexions HDMI avant 10

Schéma 10 : Connexions HDMI à l’arrière 11

Afchage des menus sur écran 12

Remarques importantes concernant la sécurité .............................31

A propos de Rotel .................................................32

Mise en route ....................................................32

Caractéristiques Vidéo 32

Caractéristiques Audio 32

Caractéristiques Surround 32

Autres fonctions 32

Déballage 32

Installation 33

Vue générale de la connectique . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Entrées et sorties HDMI .............................................33

Entrées HDMI IN arrières 1-6 r 33

Entrée HDMI IN avant 6 33

Sorties moniteur HDMI e 33

Sorties et entrées audio .............................................34

Entrée PHONO f 34

Entrées TUNER f 34

Entrée CD f 34

Entrée AUX f 34

Entrée BALANCED (Symétrique) d 34

Entrées MULTI g 34

Sorties Préampli h 34

Entrées Numériques w 34

Entrée PC-USB t 34

Entrée USB en face avant 5 35

Autres Connexions ................................................35

Prise secteur j 35

Interrupteur principal de mise sous tension a 35

Connexions 12V TRIGGER i 35

Prise jack REM IN o 35

Prises jack IR OUT p 35

Rotel Link [ 35

Prise RS232 y 35

Prise Réseau u 35

CONNEXIONS ....................................................36

Connexion des amplicateurs de puissance 36

Connexion d’un caisson de grave 36

Connexions à un lecteur DVD, Blu-ray, un récepteur câble, satellite,

console de jeux ou tuner HDTV 36

Connexion à un lecteur Blu-ray ou DVD 36

Connection d’un diffuseur vidéo 36

Connexion d’un lecteur de CD ou d’une source XLR 36

Connexion d’un tuner 37

Connexion d’un iPod / iPhone 37

Vue d’ensemble de la façade .........................................37

Ecran en face avant 3 37

Capteur de télécommande 2 37

RSP-1576 Processeur Surround

Tous les appareils Rotel sont conçus en totale conformité

avec les directives internationales concernant les

restrictions d’utilisation de substances dangereuses

(RoHS) pour l’environnement, dans les équipements

électriques et électroniques, ainsi que pour le recyclage

des matériaux utilisés (WEEE, pour Waste Electrical

and Electronic Equipment). Le symbole du conteneur

à ordures barré par une croix indique la compatibilité

avec ces directives, et le fait que les appareils peuvent

être correctement recyclés ou traités dans le respect

total de ces normes.

STANDBYSTANDBY

RSP-1576

HDMI

MUTE2CH SUR + DISPLAYBYPASS

VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7

USB PC-USB XLR TUNER CD PHONO BT

5V 2.1A

Assignation des connecteurs

Audio Symétrique (prise XLR 3 broches) :

Pin 1 : Masse/Terre

Pin 2 : Phase/+ve /Point chaud

Pin 3 : Hors Phase /-ve / Point froid

L’éclair dans un triangle équilatéral indique

la présence interne de tensions électriques

élevées susceptibles de présenter des

risques graves d’électrocution.

Le point d’exclamation dans un triangle

équilatéral indique à l’utilisateur la

présence de conseils et d’informations

importantes dans le manuel d’utilisation

accompagnant l’appareil. Leur lecture est

impérative.

DAB

+ 147 hidden pages