PANJIT P6KE100A, P6KE100, P6KE10A, P6KE10CA, P6KE11 Datasheet

P6KE SERIES

GLASS PASSIVATED JUNCTION TRANSIENT VOLTAGE SUPPRESSOR

VOLTAGE - 6.8 TO 440 Volts	600Watt Peak Power	5.0 Watt Steady State
FEATURES
!" Plastic package has Underwriters Laboratory
Flammability Classification 94V-O		DO-15

!" Glass passivated chip junction in DO-15 package !" 600W surge capability at 1ms

!" Excellent clamping capability !" Low zener impedance

!" Fast response time: typically less than 1.0 ps from 0 volts to BV min

!" Typical IR less than 1μA above 10V

!" High temperature soldering guaranteed: 260 /10 seconds/.375”,(9.5mm) lead length/5lbs., (2.3kg) tension

MECHANICAL DATA

Case: JEDEC DO-15 molded plastic Terminals: Axial leads, solderable per MIL-STD-202, Method 208 Polarity: Color band denoted cathode

except Bipolar Mounting Position: Any Weight: 0.015 ounce, 0.4 gram

DEVICES FOR BIPOLAR APPLICATIONS

For Bidirectional use C or CA Suffix for types P6KE6.8 thru types P6KE440

Electrical characteristics apply in both directions.

MAXIMUM RATINGS AND CHARACTERISTICS

Ratings at 25 ambient temperature unless otherwise specified.

Single phase, half wave, 60Hz, resistive or inductive load.

For capacitive load, derate current by 20%.

	RATING	SYMBOL	VALUE		UNITS
	Peak Power Dissipation at TA=25 , TP=1ms(Note 1)	PPK	Minimum 600		Watts
	Steady State Power Dissipation at TL=75 Lead	PD	5.0		Watts
	Lengths .375”,(9.5mm) (Note 2)
	Peak Forward Surge Current, 8.3ms Single Half Sine-Wave	IFSM	100		Amps
	Superimposed on Rated Load(JECED Method) (Note 3)

Operating and Storage Temperature Range

TJ,TSTG

-65 to +175

NOTES:

1.Non-repetitive current pulse, per Fig. 3 and derated above TA=25 per Fig. 2. 2.Mounted on Copper Leaf area of 1.57in2(40mm2).

3.8.3ms single half sine-wave, duty cycle= 4 pulses per minutes maximum.

RATING AND CHARACTERISTIC CURVES P6KE SERIES

PPPM, PEAK PUSE POWER, kW

100							CURRENT(Ipp)	100
								75
							OR
				NON-REPETITIVE PULSE			POWER(Ppp)	50
10				WAVEFORM SHOWN IN
				FIGURE 3 TA = 25
1.0							PULSE	25
							PEAK	0	25	50	75	100	125	150	175	200
0.1								0
0.1	μs	1.0 μs	10 μs	100 μs	1.0ms	10ms
			td, PULSE WIDTH, SEC						TA, AMBIENT TEMPERATURE,

Fig. 1-PEAK PULSE POWER RATING CURVE

Fig. 2-PULSE DERATING CURVE

Ippm, PEAK PULSE CURRENT, %

150		TA = 25		6,000			TJ = 25
				4,000
	tf = 10μsec	Pulse Width(td) is Defined as the					f = 1.0MHz
		Point Where the Peak Current					Vsig = 50mVp-p
				2,000
	Peak Value Ippm	Decays to 50% of lpp
100				1,000
	Half Value-Ipp			800
	2			600		MEASURED AT
				400		ZERO BIAS
		10/1000μsec Waveform
50						MEASURED AT
		as Defined by R.E.A.		200
						STAND-OFF
						VOLTAGE(VMW)
				100
0	td		e-kt	80
	1.0	2.0	3.0	60
0				4.0
				40
	t, TIME , ms
				20
	Fig. 3-PULSE WAVEFORM			10
						10	20	100	200
				1.0	2.0
				V(WM), REVERSE STAND-OFF VOLTAGE, VOLTS

Fig. 4-TYPICAL JUNCTION CAPACITANCE

UNIDIRECTIONAL

STEADY STATE POWER	FORWARD SURGE
Pm(AV)	Ifsm, PEAK