DATA SHEET
GBU10A~GBU10K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE - 50 to 800 Volts CURRENT - 10.0 Amperes
FEATURES
•Plastic material has Underwriters Laboratory Flammability Classification 94V-O
•Ideal for printed circuit board
•Reliable low cost construction utilizing molded plastic technique
•Surge overload rating: 200 Amperes peak
•High temperature soldering guaranteed:
260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
MECHANICALDATA
Case: Reliable low cost construction utilizing molded plastic technique
Terminals: Leads solderable per MIL-STD-202,
Method 208
Mounting position: Any
Mounting torque: 5 in. lb. Max.
Weight: 0.15 ounce, 4.0 grams
|
|
GBU |
|
|
|
|
|
.880(22.3) |
|
|
|
) |
) |
.860(21.8) |
|
|
|
7.90 |
7.40 |
.160(4.1) |
|
||
( |
( |
.140(3.5) |
|
||
.310 |
.290 |
|
|||
|
|
|
|
||
|
|
) ) |
) |
) |
|
|
|
2.03 |
1.52 |
18.8 |
18.3 |
|
|
( |
( |
( |
( |
) ) |
.080 |
.060 |
.740 |
.720 |
|
|
|
|
|
||
2.16 |
1.65 |
|
|
|
|
( |
( |
|
|
) |
) |
.085 |
.065 |
R |
|
18.0 |
17.5 |
|
|
|
( |
( |
|
|
|
1.90 |
|
.710 |
.690 |
|
|
) |
|
|
|
|
|
( |
|
|
|
.100(2.54) |
.075 |
|
|
|
|
|
|
|
|
||
.085(2.16) |
|
|
|
|
|
|
.080(2.03) |
|
|
|
|
|
.065(1.65) |
|
|
|
|
|
.190(4.83) |
.050(1.27) |
|
||
|
.210(5.33) |
.040(1.02) |
|
||
Unit: inch ( mm )
.140(3.56)
.130(3.30)
.040(1.02)
.030(0.76)
.022(0.56)
.018(0.46)
MAXIMUMRATINGSANDELECTRICALCHARACTERISTICS
Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.
|
GBU10A |
GBU10B |
GBU10D |
GBU10G |
GBU10J |
GBU10K |
UNIT |
||
|
|
|
|||||||
Maximum Recurrent Peak Reverse Voltage |
50 |
100 |
200 |
|
400 |
600 |
800 |
|
V |
Maximum RMS Input Voltage |
35 |
70 |
140 |
|
280 |
420 |
560 |
|
V |
Maximum DC Blocking Voltage |
50 |
100 |
200 |
|
400 |
600 |
800 |
|
V |
Maximum Average Forward TC=100°C |
|
|
|
|
|
|
|
|
A |
|
|
10.0 |
|
|
|
|
|||
Rectified Output Current at |
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
I2t Rating for fusing ( t<8.35ms) |
|
|
127 |
|
|
|
A2sec |
||
Peak Forward Surge Current single sine-wave superimposed on |
|
|
200 |
|
|
|
|
|
|
rated load(JEDEC method) |
|
|
|
|
|
Apk |
|||
|
|
|
|
|
|
|
|||
Maximum Instantaneous Forward Voltage Drop per element at 5.0A |
|
|
1.0 |
|
|
|
Vpk |
||
|
|
|
|
|
|
|
|
|
|
Maximum Reverse Leakage at rated TA=25° |
|
|
5.0 |
|
|
|
µA |
||
CDc Blocking Voltage per element TC=100°C |
|
|
500 |
|
|
µA |
|||
|
|
|
|
|
|
|
|
|
|
Typical Thermal Resistance per leg(Note 2) RθJA |
|
|
8.6 |
|
|
|
°C |
/ W |
|
Typical Thermal Resistance per leg(Note 3) RθJC |
|
|
3.1 |
|
|
|
°C |
/ W |
|
Operating and Storage Temperature Range, TJ,TSTG |
|
|
-55+150 |
|
|
°C |
|||
|
|
|
|
|
|
|
|
|
|
NOTES:
1.Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2.Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3.Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate.
DATE : AUG.29.2002 |
PAGE . 1 |
Loading...