PANJIT GBU4D, GBU4B, GBU4K, GBU4J, GBU4G Datasheet
...
DATA SHEET
GBU4A~GBU4K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE 50 to 800 Volts CURRENT - 4.0 Amperes |
GBU |
FEATURES |
|
|
.880(22.3) |
|
|
|
|
• Plastic material has Underwriters Laboratory |
|
|
|
|
|
|
|
) |
) |
.860(21.8) |
|
|
|
|
|
Flammability Classification 94V-O |
7.90 |
7.40 |
|
.160(4.1) |
|
||
|
( |
( |
|
.140(3.5) |
|
||
• Ideal for printed circuit board |
.310 |
.290 |
|
|
|||
|
|
|
|
|
|||
• Reliable low cost construction utilizing molded plastic technique |
|
|
) ) |
) |
) |
||
|
|
|
|||||
• Surge overload rating: 150 Amperes peak |
|
|
|
2.03 |
1.52 |
18.8 |
18.3 |
|
|
( |
( |
( |
( |
||
• High temperature soldering guaranteed: |
) |
) |
|
.080 |
.060 |
.740 |
.720 |
260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension |
2.16 |
1.65 |
|
|
|
) |
) |
( |
( |
|
|
|
|||
|
.085 |
.065 |
R |
|
|
18.0 |
17.5 |
MECHANICAL DATA |
|
|
|
|
( |
( |
|
|
|
1.90 |
|
|
.710 |
.690 |
|
|
|
|
) |
|
|
|
|
|
|
|
( |
|
|
|
|
Case: Reliable low cost construction utilizing |
.100(2.54) |
.075 |
|
|
|
|
|
molded plastic technique |
|
|
|
|
|
||
.085(2.16) |
|
|
|
|
|
||
Terminals: Leads solderable per MIL-STD-202, |
|
.080(2.03) |
|
|
|
|
|
Method 208 |
|
.065(1.65) |
|
|
|
|
|
Mounting position: Any |
|
.190(4.83) |
|
.050(1.27) |
|
||
Mounting torque: 5 in. lb. Max. |
|
.210(5.33) |
|
.040(1.02) |
|
||
|
|
|
|
|
|
|
|
Weight: 0.15 ounce, 4.0 grams |
|
|
|
|
|
|
|
Unit: inch ( mm )
.140(3.56)
.130(3.30)
.040(1.02)
.030(0.76)
.022(0.56)
.018(0.46)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
|
Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz. |
|
|
|
|
|
|
|
|||
|
For Capacitive load derate current by 20%. |
|
|
|
|
|
GBU4J |
GBU4K |
UNIT |
||
|
|
GBU4A |
GBU4B |
GBU4D |
|
GBU4G |
|||||
|
Maximum Recurrent Peak Reverse Voltage |
50 |
100 |
200 |
|
400 |
600 |
800 |
|
V |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Maximum RMS Input Voltage |
35 |
70 |
140 |
|
280 |
420 |
560 |
|
V |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Maximum DC Blocking Voltage |
50 |
100 |
200 |
|
400 |
600 |
800 |
|
V |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Maximum Average Forward TC=100°C |
|
|
|
4.0 |
|
|
|
A |
||
|
Rectified Output Current atTA=40°C |
|
|
|
3.0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
I2t Rating for fusing ( t<8.3ms) |
|
|
|
93 |
|
|
A2sec |
|||
|
Peak Forward Surge Current single sine-wave superimposed on |
|
|
|
150 |
|
|
Apk |
|||
|
rated load(JEDEC method) |
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Maximum Instantaneous Forward Voltage Drop per element at 2.0A |
|
|
|
1.0 |
|
|
Vpk |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
Maximum Reverse Leakage at rated TA=25° |
|
|
|
5 |
|
|
|
µA |
||
|
CDc Blocking Voltage per element TC=100°C |
|
|
|
500 |
|
|
|
µA |
||
|
Typical Thermal Resistance per leg(Note 2) Rθ JA |
|
|
|
19 |
|
|
°C |
/ W |
||
|
Typical Thermal Resistance per leg(Note 3) Rθ JA |
|
|
|
4 |
|
|
°C |
/ W |
|
|
|
Operating and Storage Temperature Range, TJ,TSTG |
|
|
-55+150 |
|
|
|
°C |
|
||
NOTES:
1.Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2.Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3.Units Mounted on a 2.0 x 1.6" x 0.3" thick (5 x 4 x 0.8cm) AL plate.
DATE : SEP.12.2002 |
PAGE . 1 |
Loading...