CP800 THRU CP808
SINGLE-PHASE SILICON BRIDGE
VOLTAGE - 50 to 800 Volts |
CURRENT - P.C. MTG 3A, HEAT-SINK MTG 8A |
Recongnized File #E111753 |
CP-8 |
FEATURES
•Surge overload rating— 200 Amperes peak
•Low forward voltage drop and reverse leakage
•Small size, simple installation
•Plastic package has Underwriter Laboratory Flammability Classification 94V-O
•Reliable low cost construction utilizing molded plastic technique
MECHANICAL DATA
Mounting position: Any
Weight: 0.24 ounce, 6.9 grams
Terminals: Leads solderable per MIL-STD-202,
Method 208
Mounting torque: Thro hole for #6 screw
MACXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
At 25 ¢J ambient temperature unless otherwise noted; resistive or inductive load at 60Hz .
|
|
CP800 |
CP801 |
CP802 |
|
CP804 |
CP806 |
CP808 |
UNITS |
|
Max Recurrent Peak Reverse Voltage |
50 |
100 |
200 |
|
|
400 |
600 |
800 |
V |
|
Max Bridge Input Voltage RMS |
35 |
70 |
140 |
|
|
280 |
420 |
560 |
V |
|
Max Average Rectified Output at TC=50 ¢J * |
|
|
|
|
8.0 |
|
|
A |
||
See Fig. 2 |
at TA=40 ¢J ** |
|
|
|
|
3.0 |
|
|
A |
|
Peak One Cycle Surge Overload Current |
|
|
|
200 |
|
|
A |
|||
Max Forward Voltage Drop per element at |
|
|
|
|
1.1 |
|
|
V |
||
4.0A DC & 25 ¢J . See Fig. 3 |
|
|
|
|
|
|
|
|
|
|
Max Rev Leakage at rated Dc Blocking |
|
|
|
|
|
|
|
|
|
|
Voltage per element at 25 ¢J |
|
|
|
10.0 |
|
|
£g A |
|||
See Fig 4 |
at100 ¢J |
|
|
|
|
1.0 |
|
|
mA |
|
I2t Rating for fusing ( t<8.3ms) |
|
|
|
166 |
|
|
A2Sec |
|||
Typical junction capacitance per leg (Note 4) CJ |
|
|
|
200 |
|
|
PF |
|||
Typical Thermal Resistance per leg (Note 3) R £KJA |
|
|
|
|
21 |
|
|
¢J /W |
||
Typical Thermal Resistance per leg (Note 2) R £KJL |
|
|
|
|
6 |
|
|
|
||
Operating Temperature Range |
|
|
-55 |
TO +125 |
|
|
¢J |
|||
|
|
|
|
|
|
|
|
|||
Storage Temperature Range |
|
|
-55 |
TO +150 |
|
|
¢J |
|||
|
|
|
|
|
|
|
|
|
|
|
NOTES:
1.Bolt down on heat-sink with silicon thermal compound between bridge and mounting surface for maximum heat transfer with #6 screw.
2.Units Mounted on a 8.6”¡Ñ 8.6” ¡Ñ 24” thick (22 ¡Ñ 22 ¡Ñ 0.6cm) AL plate heatsink.
3.Units Mounted on P.C.B at 0.375”(9.5mm) lead length with 0.5 ¡Ñ 0.5”(12 ¡Ñ 12mm)copper pads.
4.Measured at 1.0MHZ and applied reverse voltage.