Maytag MER6741BA User Manual

0 (0)
Electric Smoothtop and Electric
Coil Double Oven Range
®
Precision Touch 500 Series
Use and Care Guide
Table of Contents
Important Safety
Instructions ............................... 1-4
Surface Cooking ...................... 5-7
Controls Coil Elements Smoothtop Surface
Oven Cooking ......................... 8-15
Upper Oven Control (Manual Clean) Lower Oven Control (Self-Clean) Baking Cook & Hold Delay Bake Keep Warm Broiling (Lower Oven Only) Oven Racks
Care & Cleaning ...................16-19
Self-Clean Oven (Lower Oven Only) Cleaning Procedures
Maintenance ............................... 20
Oven Doors and Windows Oven Lights
Troubleshooting ...................21-22
Warranty & Service ..... Back Page
©2006 Maytag Appliances Sales Co. Litho U.S.A .Form No. A/01/08 Part No. 8113P719-60
Installer: Please leave this guide with this appliance.
Consumer: Please read and keep this guide for future refer-
ence. Keep sales receipt and/or canceled check as proof of purchase.
Model Number __________________________________
Serial Number __________________________________
Date of Purchase ________________________________
If you have questions, call: Customer Assistance 1-800-688-9900 USA 1-800-688-2002 Canada 1-800-688-2080 ( U.S. TTY for hearing or speech impaired) (Mon.-Fri., 8 am-8 pm Eastern Time) Internet: http://www.maytag.com
In our continuing effort to improve the quality and performance of our cooking products, it may be necessary to make changes to the appliance without revising this guide.
For service information, see back page.
Important Safety
General Instructions
To ensure proper and safe operation: Appliance
must be properly installed and grounded by a qualified technician. Do not attempt to adjust, repair, service, or replace any part of your appliance unless it is specifically recommended in this guide. All other servicing should be referred to a qualified servicer.
Always disconnect power to appliance before servicing.
WARNING
• ALL RANGES CAN TIP AND CAUSE INJURIES TO PERSONS
• INSTALL ANTI-TIP DEVICE PACKED WITH RANGE
• FOLLOW ALL INSTALLATION INSTRUCTIONS
WARNING: To reduce risk of tipping of the appliance from abnormal usage or by excessive loading of the oven doors, the appliance must be secured by a properly installed anti-tip device.
Instructions
Warning and Important Safety Instructions appearing in this guide are not meant to cover all possible conditions and situations that may occur. Common sense, caution, and care must be exercised when installing, maintaining, or operating the appliance.
Always contact your manufacturer about problems or conditions you do not understand.
Recognize Safety Symbols, Words, Labels
WARNING
WARNING – Hazards or unsafe practices which COULD result in severe personal injury or death.
CAUTION
CAUTION – Hazards or unsafe practices which COULD result in minor personal injury.
To check if device is properly installed, look underneath range with a flashlight to make sure one of the rear leveling legs is properly engaged in the bracket slot. The anti-tip device secures the rear leveling leg to the floor when properly engaged. You should check this anytime the range has been moved.
In Case of Fire
Turn off appliance and ventilating hood to avoid spreading the flame. Extinguish flame then turn on hood to remove smoke and odor.
• Cooktop: Smother fire or flame in a pan with a lid or cookie sheet.
NEVER pick up or move a flaming pan.
• Ovens: Smother fire or flame by closing the oven doors.
Do not use water on grease fires. Use baking soda, a dry
chemical or foam-type extinguisher to smother fire or flame.
WARNING
Read and follow all instructions before using this appliance to prevent the potential risk of fire, electric
shock, personal injury or damage to the appliance as a result of improper usage of the appliance. Use appliance only for its intended purpose as described in this guide.
NEVER use an appliance as a step to reach cabinets above. Misuse of appliance doors, such as stepping, leaning or sitting on the door, may result in possible tipping of the appliance, breakage of door, and serious injuries.
1
Important Safety Instructions
If appliance is installed near a window, precautions should be taken to prevent curtains from blowing over surface elements.
NEVER use appliance to warm or heat the room. Failure to follow this instruction can lead to possible burns, injury, fire, or damage to the appliance.
NEVER wear loose-fitting or hanging garments while using the appliance. Clothing could catch utensil handles or ignite and cause burns if garment comes in contact with hot heating elements.
To ensure proper operation and to avoid damage to the appliance or possible injury, do not adjust, service, repair or replace any part of the appliance unless specifically recommended in this guide. Refer all other servicing to a qualified technician.
NEVER store or use gasoline or other combustible or flammable materials in the ovens, near surface units or in the vicinity of this appliance as fumes could create a fire hazard or an explosion.
To prevent grease fires, do not let cooking grease or other flammable materials accumulate in or near the appliance.
Use only dry potholders. Moist or damp potholders on hot surfaces may result in a steam burn. Do not let potholders touch hot heating elements. Do not use a towel or other bulky cloth which could easily touch hot heating elements and ignite.
Always turn off all controls when cooking is completed.
NEVER heat unopened containers on the surface unit or in the ovens. Pressure build-up in the container may cause container to burst resulting in burns, injury or damage to the appliance.
NEVER use aluminum foil to line drip bowls or cover oven racks or oven bottoms. This could result in risk of electric shock, fire, or damage to the appliance. Use foil only as directed in this guide.
Aerosol-type cans are EXPLOSIVE when exposed to heat and may be highly flammable. Do not use or store near appliance.
Cooktop
NEVER leave surface units unattended, especially when
using high heat. An unattended boilover could cause smoking and a greasy spillover can cause a fire.
This appliance is equipped with different size surface elements. Select pans with flat bottoms large enough to cover element. Fitting pan size to element will improve cooking efficiency.
If pan is smaller than element, a portion of the element will be exposed to direct contact and could ignite clothing or potholder.
Only certain types of glass, glass-ceramic, ceramic, earthenware, or other glazed utensils are suitable for cooktop or oven service without breaking due to the sudden change in temperature. Follow utensil manufacturer’s instructions when using glass.
This appliance has been tested for safe performance using conventional cookware. Do not use any devices or accessories that are not specifically recommended in this guide. Do not use element covers, stove top grills or add-on oven convection systems. The use of devices or accessories that are not expressly recommended in this guide can create serious safety hazards, result in performance problems, and reduce the life of the components of this appliance.
Turn pan handle toward center of cooktop, not out into the room or over another surface element. This reduces the risk of burns, ignition of flammable materials, or spillage if pan is accidently bumped or reached by small children.
Glass-Ceramic Cooktop
NEVER cook on broken cooktop. If cooktop should break,
cleaning solutions and spillovers may penetrate the broken cooktop and create a risk of electric shock. Contact a qualified technician immediately.
Clean cooktop with caution. Some cleaners can produce noxious fumes if applied to a hot surface. If a wet sponge, cloth, or paper towel is used on a hot cooking area, be careful to avoid steam burn.
2
Important Safety Instructions
Coil Elements
To prevent damage to removable surface heating elements, do not immerse, soak or clean in a dishwasher or self-clean oven. A damaged element could short, resulting in a fire or shock hazard.
Make sure drip bowls are in place as absence of these bowls during cooking could damage wiring.
Protective Liners: Do not use aluminum foil to line surface unit drip bowls or oven bottoms, except as suggested in the guide. Improper installation of these liners may result in a risk of electric shock or fire.
Heating Elements
NEVER touch surface or oven heating elements, areas near
elements, or interior surfaces of ovens.
Heating elements may be hot even though they are dark in color. Areas near surface elements and interior surfaces of the ovens may become hot enough to cause burns. During and after use, do not touch or let clothing or other flammable materials contact heating elements, areas near elements, or interior surfaces of ovens until they have had sufficient time to cool.
Other potentially hot surfaces include: cooktop, areas facing the cooktop, oven vent, surfaces near the vent opening, oven doors, areas around the doors and oven windows.
Deep Fat Fryers
Use extreme caution when moving the grease pan or disposing of hot grease. Allow grease to cool before attempting to move pan.
Ovens
Use care when opening doors. Let hot air or steam escape before removing or replacing food.
For proper oven operation and performance, do not block or obstruct oven vent duct. When ovens are in use, the vent and surrounding area near the vent may become hot enough to cause burns.
Always place oven racks in desired locations while ovens are cool. If rack must be moved while an oven is hot, do
not let potholder contact hot element in oven.
Self-Cleaning Ovens
CAUTION
Before self-cleaning the oven, remove the oven racks, broiler pan, food and any other utensils. Wipe spillovers to prevent excessive smoke and flare-ups.
Clean only parts listed in this guide. Do not clean door gasket. The gasket is essential for a good seal. Do not rub, damage, or move the gasket.
Do not use oven cleaners. No commercial oven cleaner or oven liner protective coating of any kind should be used in or around any part of the ovens.
Wipe up excessive spillovers, especially greasy spills, before the clean cycle to prevent smoking, flare-ups or flaming.
It is normal for the cooktop to become hot during a clean cycle. Therefore, avoid touching the cooktop, door, window or oven vent during a clean cycle.
3
Important Safety Instructions
Child Safety Important Safety Notice
CAUTION
NEVER store items of interest to children in cabinets above
an appliance. Children climbing on the appliance or on the appliance doors to reach items could be seriously injured.
NEVER leave children alone or unsupervised in area where appliance is in use or is still hot.
NEVER allow children to sit or stand on any part of the appliance as they could be injured or burned.
Children must be taught that the appliance and utensils in or on it can be hot. Let hot utensils cool in a safe place, out of reach of small children. Children should be taught that an appliance is not a toy. Children should not be allowed to play with controls or other parts of the unit.
Ventilating Hoods
Clean range hood and filters frequently to prevent grease or other flammable materials from accumulating on hood or filter and to avoid grease fires.
Turn the fan on when flambéing foods (such as Cherries Jubilee) under the hood.
and Warning
The California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65) requires the Governor of California to publish a list of substances known to the State of California to cause cancer or reproductive harm, and requires businesses to warn customers of potential exposures to such substances.
Users of this appliance are hereby warned that when the oven is engaged in the self-clean cycle, there may be some low-level exposure to some of the listed substances, including carbon monoxide. Exposure to these substances can be minimized by properly venting the oven to the outdoors by opening the windows and/or door in the room where the appliance is located during the self-clean cycle.
IMPORTANT NOTICE REGARDING PET BIRDS: Never keep pet birds in the kitchen or in rooms where the fumes from the kitchen could reach. Birds have a very sensitive respiratory system. Fumes released during an oven self-cleaning cycle may be harmful or fatal to birds. Fumes released due to overheated cooking oil, fat, margarine and overheated non-stick cookware may be equally harmful.
Save These Instructions for Future Reference
4
Surface Cooking
Surface Controls
Use to turn on the surface elements. An infinite choice of heat settings is available from Low to High. The knobs can be set on or between any of the settings.
Setting the Controls
1. Place pan on surface element.
2. Push the knob in and turn in either direction to the desired heat setting.
• The control panel is marked to identify which
element the knob controls. For example, the graphic at right indicates left front element.
3. There is an element “ON” indicator light on the control panel. When any surface control knob is turned on, the light will turn on. The light will turn off when all the surface elements are turned off.
4. After cooking, turn knob to OFF. Remove pan.
Suggested Heat Settings
The size, type of cookware and cooking operation will affect the heat setting.
Low (2): Use to keep foods warm and melt chocolate and butter.
Med. Low (3-4): Use to continue cooking covered foods or steam foods.
High (10): Use to bring liquid to a boil. Always reduce setting to a lower heat when liquids begin to boil or foods begin to cook.
CAUTION
BEFORE COOKING
• Always place a pan on the surface unit before you turn it on. To prevent damage to range, never operate surface unit without a pan in place.
NEVER use the cooktop to store for food or cookware.
DURING COOKING
• Be sure you know which knob controls which surface unit. Make sure you turned on the correct surface unit.
• Begin cooking on a higher heat setting then reduce to a lower setting to complete the operation. Never use a high heat setting for extended cooking.
NEVER allow a pan to boil dry. This could damage the pan and the appliance.
NEVER touch cooktop until it has cooled. Expect some parts of the cooktop, especially around the surface units, to become warm or hot during cooking. Use potholders to protect hands.
AFTER COOKING
• Make sure surface unit is turned off.
• Clean up messy spills as soon as possible.
OTHER TIPS
• If cabinet storage is provided directly above cooking surface, limit it to items that are infrequently used and can be safely stored in an area subjected to heat. Temperatures may be unsafe for items such as volatile liquids, cleaners or aerosol sprays.
NEVER leave any items, especially plastic items, on the cooktop. The hot air from the vent may ignite flammable items, melt or soften plastics, or increase pressure in closed containers, causing them to burst.
NEVER allow aluminum foil, meat probes or any other metal object, other than a pan on a surface element, to contact heating elements.
Medium (5-7): Use to maintain slow boil for large amounts of liquids and for most frying operations.
Med. High (8-9): Use to brown meat, heat oil for deep fat frying or sauteing. Maintain fast boil for large amounts of liquids.
Coil Element Surface
Notes:
• Clean cooktop after each use.
• Wipe acidic or sugary spills as soon as the cooktop has cooled as these spills may discolor or etch the porcelain.
To protect drip bowl finish:
• To lessen discoloration and crazing, avoid using high heat for long periods.
Do not use oversized cookware. Pans should not extend more than 1-2 inches beyond the element.
• When home canning or cooking with big pots, use the Canning Element (Model CE1). Contact your Maytag dealer for details or call 1-877-232-6771 USA or 1-800-688-8408 Canada to order.
• Clean frequently. (See page 19.)
5
6
Coil Elements
• When an element is on, it will cycle on and off to maintain the heat setting.
• Coil elements are self-cleaning. Do not immerse in water.
To remove: When cool, raise element.
Carefully pull out and away from receptacle.
To replace: Insert element
terminals into receptacle. Guide the element into place. Press down on the outer edge of element until it sits level on drip bowl.
Drip Bowls
The drip bowls under each surface element catch boilovers and must always be used. Absence of drip bowls during cooking may damage wiring.
To prevent the risk of electric shock or fire, never line drip bowls with aluminum foil.
Drip bowls will discolor (blue/gold stains) or craze over time if overheated. This discoloration or crazing is permanent. This will not affect cooking performance.
TERMINALS
Surface Cooking
Notes:
Cooktop may emit light smoke and odor the first few times the cooktop is used. This is normal.
Smoothtop cooktops retain heat for a period of time after the element is turned off. Turn the elements off a few minutes before food is completely cooked and use the retained heat to complete cooking. When the hot surface light turns off, the cooking area will be cool enough to touch. Because of the way they retain heat, the smoothtop elements will not respond to changes in settings as quickly as coil elements.
• In the event of a potential boilover, remove the pan from the cooking surface.
Never attempt to lift the cooktop.
• The smoothtop surface may appear discolored when it is hot. This is normal and will disappear when the surface cools.
Smoothtop Surface
Cooking Areas
The cooking areas on your range are identified by permanent circles on the smoothtop surface. For most efficient cooking, fit the pan size to the element size.
Pans should not extend more than 1/2 to 1-inch beyond the cooking area.
When a control is turned on, a glow can be seen through the smoothtop surface. The element will cycle on and off to
maintain the preset heat setting, even on Hi.
For more information on cookware, refer to Cookware Recommendations on page 7.
Hot Surface Light
The Hot Surface indicator light is located on the control panel. The light will be illuminated when any cooking area is hot. It will remain on, even after the control is turned off, until the area has cooled.
DUAL ELEMENT
(SELECT MODELS)
SINGLE
ELEMENT
Cont.
Tips to Protect the Smoothtop Surface
Cleaning (see page 18 for more information)
• Before first use, clean the cooktop.
• Clean your cooktop daily or after each use. This will keep your cooktop looking good and can prevent damage.
• If a spillover occurs while cooking, immediately clean the spill from the cooking area while it is hot to prevent a tough cleaning chore later. Using extreme care, wipe spill with a clean dry towel.
Do not allow spills to remain on the cooking area or the cooktop trim for a long period of time.
Never use abrasive cleansing powders or scouring pads which will scratch the cooktop.
Never use chlorine bleach, ammonia or other cleansers not specifically recommended for use on glass-ceramic.
To Prevent Marks and Scratches
Do not use glass pans. They may scratch the surface.
Never place a trivet or wok ring between the surface and pan. These items can mark or etch the top.
SINGLE
ELEMENT
DUAL ELEMENT
(SELECT MODELS)
Surface Cooking
Do not slide aluminum pans across a hot surface. The pans may leave marks which need to be removed promptly. (See Cleaning, page 18.)
• Make sure the surface and the pan bottom are clean before turning on to prevent scratches.
• To prevent scratching or damage to the glass-ceramic top, do not leave sugar, salt or fats on the cooking area. Wipe the cooktop surface with a clean cloth or paper towel before using.
Never slide heavy metal pans across the surface since these may scratch.
To Prevent Stains
• Never use a soiled dish cloth or sponge to clean the
cooktop surface. A film will remain which may cause stains on the cooking surface after the area is heated.
• Continuously cooking on a soiled surface may/will result in a permanent stain.
To Prevent Other Damage
Do not allow plastic, sugar or foods with high sugar content to melt onto the hot cooktop. Should this happen, clean immediately. (See Cleaning, page 18.)
Never let a pan boil dry. This will damage the surface and pan.
Never use cooktop as a work surface or cutting board.
Never cook food directly on the surface.
Do not use a small pan on a large element. Not only does this waste energy, but it can also result in spillovers burning onto the cooking area, which requires extra cleaning.
Do not use non-flat specialty items that are oversized or uneven such as round-bottom woks, rippled-bottom and/or oversized canners and griddles.
Do not use foil or foil-type containers. Foil may melt onto the glass. If metal melts on the cooktop, do not use. Call an authorized servicer.
Cookware Recommendations
Using the right cookware can prevent many problems, such as food taking longer to cook or achieving inconsistent results. Proper pans will reduce cooking times, use less energy, and cook food more evenly.
Flat Pan Tests
See if your pans are flat.
The Ruler Test:
1. Place a ruler across the bottom of the pan.
2. Hold it up to the light.
3. Little or no light should be visible under the ruler.
The Bubble Test:
1. Put 1 inch of water in the pan. Place on cooktop and turn control to High.
2. Watch the formation of the bubbles as the water heats. Uniform bubbles mean good performance, and uneven bubbles indicate hot spots and uneven cooking.
Select Avoid
Flat, smooth-bottom Pans with grooved or warped bottoms. pans. Pans with uneven bottoms do not cook
efficiently and sometimes may not boil liquid.
Heavy-gauge pans. Very thin-gauge metal or glass pans.
Pans that are the Pans smaller or larger than the same size as the element by 1 inch. element.
Secure handles. Cookware with loose or broken handles.
Heavy handles that tilt the pan.
Tight-fitting lids. Loose-fitting lids.
Flat-bottom woks. Woks with a ring-stand bottom.
Canning and Oversize Cookware
All canners and large pots must have flat bottoms and must be made from heavy-gauge materials. This is critical
on smoothtop surfaces. The base must not be more than 1 inch larger than the element.
When canners and pots do not meet these standards, cooking times may be longer, and cooktops may be damaged.
Some canners are designed with smaller bases for use on smoothtop surfaces.
When canning, use the High heat setting only until the water comes to a boil or pressure is reached in the canner.
Reduce to the lowest heat setting that maintains the boil or pressure. If the heat is not turned down, the cooktop may be damaged.
7
Loading...
+ 16 hidden pages