Maytag MET3800TW0, YWET3300SQ1, YWET3300SQ0, WGT3300SQ0, WET3300SQ1 Installation Guide

...

0 (0)

27"(69CM)ELECTRICWASHER/DRYER

INSTALLATION INSTRUCTIONS

INSTRUCCIONES DE INSTALACION DE LA LAVADOR_

SECADORA ELECTRICA DE 27"(69CM)

INSTRUCTIONS D'INSTALLATION

LAVEUSE/SECHEUSE ELECTRIQUEDE 27"(69CM)

Table of Contents / Indice / Table des matii_res

WASHER/DRYER SAFETY ............................. 1

INSTALLATION INSTRUCTIONS ................... 2

Teels and Parts ............................................. 2

Alternate Parts ............................................... 2

Location Requirements ................................. 3

Drain System ................................................. 4

Electrical Requirements - U.S.A................... 4

Electrical Requirements - Canada ................ 5

Electrical Connection - U.S.A. Only ............. 6

Venting Requirements ................................. 11

Remove Shipping Strap .............................. 12

Install Leveling Legs .................................... 12

Connect the Drain Hose .............................. 12

Connect the Inlet Hoses ............................. 13

Secure the Drain Hose ................................ 14

Plan Vent System ........................................ 14

Install Vent System ...................................... 15

Level Washer/Dryer ..................................... 15

Connect Vent .............................................. 15

Complete Installation .................................. 16

SEGURIDAD DE LA

LAVADORA/SECADORA ............................... 17

INSTRUCCIONES DE INSTALACION .......... 17

Herramientas y piezas ................................. 17

Piezas alternativas ...................................... 18

Requisitos de ubicacion ............................. 18

Sistema de desagiJe .................................. 19

Requisitos el_ctricos - EE.UU..................... 19

Conexi6n el6ctrica - Solo en EE. UU.......... 21

Requisitos de ventilaci6n ............................ 26

Quite el fleje de embalaje ............................ 27

Instalacion de las patas niveladoras ........... 28

Conecte la manguera de desagL_e.............. 28

Conecte las mangueras de entrada ........... 29

Fijacion de la manguera de desagiJe .......... 30

Planificaci6n del sistema de ventilaci6n ..... 30

Instalacion del sistema de ventilacion ........ 31

Como nivelar la lavadora/secadora ............ 31

Conexi6n del ducto de escape ................... 32

Complete la instalaci6n ............................... 32

SleCURITle DE LA LAVEUSE/SleCHEUSE ... 33

INSTRUCTIONS D'INSTALLATION .............. 33

Outillage et pi_ces ....................................... 33

Autres pieces .............................................. 34

Exigences d'emplacement ........................ 34

Systeme de vidange ................................... 35

Specifications _lectriques - Canada ........... 36

Exigences concernant 1'6vacuation ............ 37

Enlever la sangle d'exp_dition .................... 38

Installation des pieds de nivellement .......... 39

Raccordement du tuyau de vidange .......... 39 Raccordement des tuyaux d'alimentation.. 39

Immobilisation du tuyau de vidange ........... 40

Planification du systeme d'_vacuation ....... 41

Installation du systeme d'_vacuation ......... 42

Nivellement de la laveuse/s_cheuse ........... 42 Raccordement du conduit d'6vacuation .... 43

Achever I'installation ................................... 43

WASHER/DRYERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

W10118289A

INSTALLATIONINSTRUCTIONS

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here.

Tools needed:

#2 Phillips and flat-blade screwdriver

Adjustable wrench that opens to 1" (2.5 cm) or 9/16"open-end wrench (for

adjusting washer/dryer feet)

1/4"nut driver or socket wrench (recommended)

Wire stripper (for U.S. only, direct wire installations)

Caulking gun and compound (for installing

new exhaust vent)

Parts supplied:

Remove parts package from the washer basket. Check that all parts were included.

• Level

• Wood block (for leveling)

• Ruler or measuring tape

• Knife

• Vent clamps

• Pliers

• Scissors

• Tin snips (for new vent installations)

Your installation may require additional parts. For information on ordering, please refer to the toll free phone numbers on the front page of the Washer/Dryer User Instructions.

If You Have You Will Need to Buy

Laundry tub or Sump pump system (if not already standpipe taller than available)

96" (2.4 m)

1" (2.5 cm) diameter 2" (5 cm) diameter to 1" (2.5 cm) standpipe diameter standpipe adapter, Part

Number 3363920

Overhead sewer Standard 20 gal. (76 L) 34" (86.4 cm)

tall drain tub or utility sink and sump

pump (available from local plumbing suppliers)

Floor drain Siphon break, Part Number 285320,

additional drain hose, Part Number 285702 and connector kit,

Part Number 285442

Drain hose too short Drain hose, Part Number 285664 and

connector kit, Part Number 285442

Lint clogged drain Drain protector, Part Number 367031

Water faucets 2 longer water fill hoses: beyond reach of fill 6 ft (1.8 m) Part Number 76314,

hoses 10 ft (3.0 m) Part Number 350008

D F

A. Water inlet hoses (2) B. Inlet hose flat washers (4)

C. Front levering feet with nuts (2)

Parts needed:

Check local codes, electrical supply and venting, and read "Electrical Requirements" and "Venting Requirements" before

purchasing parts. Mobile home installations require metal exhaust system hardware

available for purchase from the dealer from whom you purchased your washer/dryer. For further information, please reference the

"Assistance or Service" section of the Washer/Dryer User Instructions.

D. Shipping strap (not in parts

bag. See "Remove Shipping Strap. ")

E. Drain hose

£ Silver, double wire hose clamp

ExplosionHazard

Keepflammablematerialsandvapors,suchas gasoline,awayfromdryer,

Failuretodosocanresultin death, explosion, or fire.

You will need

• A location that allows for proper exhaust installation. See

"Venting Requirements."

• Aseparate 30-amp circuit.

• If you are using a power supply cord, a grounded electrical outlet located within 2 ft (61 cm) of either side of the washer/ dryer. See "Electrical Requirements."

• A sturdy floor to support the washer/dryer weight (washer/ dryer, water and load) of 500 Ibs (226.8 kg).

• A level floor with a maximum slope of 1" (2.5 cm) under entire washer/dryer. Clothes may not tumble properly and automatic sensor cycles may not operate correctly if washer/dryer is not level. Installing on carpet is not recommended.

• A water heater set to deliver 120°F (49°C) water to the washer.

• Hot and cold water faucets located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of 5-100 psi (34.5-689.6 kPa).

The washer/dryer must not be installed or stored in an area where it will be exposed to water and/or weather.

Do not operate your washer in temperatures at or below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures. See "Washer/Dryer Care" in the

Washer/Dryer User Instructions for winterizing information. Do not operate your dryer at temperatures below 45°F (7°C). At

lower temperatures, the dryer might not shut off at the end of an automatic cycle. This can result in longer drying times.

Check code requirements. Some codes limit, or do not permit, installation of the washer/dryer in garages, closets, mobile homes or sleeping quarters. Contact your local building inspector.

Installation Clearances The location must be large enough to allow the dryer door to open

fully.

Washer/Dryer Dimensions

71%"

(181.9 cm)

*Most installations require a minimum 5" (12.7 cm) clearance

behind the dryer for the exhaust vent with elbow. See "Venting Requirements."

Installation spacing for recessed area or closet installation

The following spacing dimensions are recommended for this washer/dryer. This washer/dryer has been tested for spacing of 0"

(0 cm) clearance on the sides. Recommended spacing should be considered for the following reasons:

• Additional spacing should be considered for ease of installation and servicing.

• Additional clearances might be required for wall, door and floor moldings.

• Additional spacing on all sides of the washer/dryer is recommended to reduce noise transfer.

For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilation openings are acceptable.

OoooO

Wl L

$- (13_cm)

48in.2-

(340 cm2)

24in.2-

(135cm2)

r_,ll 27 I1_,,

(2,3era) (68,6crn)

(2,3cm) (2,3cm) (81.3cm) (12,7cm)

A. Recessed area

B. Side view - closet or confined area

C. Closet door with vents

*Required spacing

**Rear clearance may be 1" (2.5 cm) when house exhaust system

is lined up directly with dryer exhaust.

Mobile Home - Additional Installation Requirements This washer/dryer is suitable for mobile home installations.

The installation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280) or the Canadian Manufactured

Home Standard, CAN/CSA-Z240 MH.

Mobile home installations require:

• Metal exhaust system hardware, which is available for

purchase from your dealer.

• Special provisions must be made in mobile homes to introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer

exhaust opening.

The washer/dryer can be installed using the standpipe drain system (floor or wall), the laundry tub drain system, or the floor drain system. Select the drain hose installation method you need.

See "Alternate Parts."

Standpipe drain system - wall or floor (views A & B) The standpipe drain requires a minimum diameter standpipe of

2" (5 cm). The minimum carry-away capacity can be no less than 17 gal. (64 L) per minute. A 2" (5 cm) diameter to 1" (2.5 cm) diameter standpipe adapter kit is available. See "Alternate Parts."

The top of the standpipe must be at least 39" (99 cm) high and no higher than 96" (2.4 m) from the bottom of the washer.

Laundry tub drain system (view C) The laundry tub needs a minimum 20 gal. (76 L)capacity. The top

of the laundry tub must be at least 34" (86.4 cm) above the floor and no higher than 96" (2.4 m) from the bottom of the washer.

Floor drain system (view D) The floor drain system requires a siphon break that may be

purchased separately. See "Alternate Parts." The siphon break must be a minimum of 28" (71 cm) from the

bottom of the washer. Additional hoses might be needed.

It is your responsibility

• To contact a qualified electrical installer.

• To be sure that the electrical connection is adequate and in conformance with the National Electrical Code, ANSl/NFPA 70-latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from: National Fire Protection Association, One Batterymarch Park,

Quincy, MA 02269. To supply the required 3 or 4 wire, single phase, 120/240 volt,

60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt electrical supply, if specified on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of the line. A

time-delay fuse or circuit breaker is recommended. Connect to an individual branch circuit. Do not have a fuse in the

neutral or grounding circuit. Do not use an extension cord.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

Electrical Connection

Toproperly install your washer/dryer, you must determine the type of electrical connection you will be using and follow the

instructions provided for it here.

• This dryer is manufactured ready to install with a 3-wire electrical supply connection. The neutral ground wire is

permanently connected to the neutral conductor (white wire) within the dryer. Ifthe dryer is installed with a 4-wire electrical supply connection, the neutral ground wire must be removed from the internal ground connector (green screw), and secured

under the neutral terminal (center or white wire) of the terminal block. When the neutral ground wire is secured under the neutral terminal (center or white wire) of the terminal block, the dryer cabinet is isolated from the neutral conductor.

• If local codes do not permit the connection of aneutral ground wire to the neutral wire, see "Optional 3-wire connection" in the "Electrical Connection - U.S.A. Only" section.

• A 4-wire power supply connection must be used when the appliance is installed in a location where grounding through

the neutral conductor is prohibited. Grounding through the neutral is prohibited for (1) new branch-circuit installations,

(2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral

conductors.

If using a power supply cord: Use a UL listed power supply cord kit marked for use with clothes

dryers. The kit should contain:

• A UL listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be type SRD or SRDT and be at

least 4 ft (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned

ends.

• A UL listed strain relief.

If your outlet looks like this:

4-wire receptacle (14-30R)

Then choose a 4-wire power supply cord with ring or spade terminals and UL listed strain relief. The 4-wire power supply cord, at least 4 ft (1.22 m) long, must have four 10-gauge copper wires

and match a 4-wire receptacle of NEMA Type 14-30R. The ground wire (ground conductor) may be either green or bare. The neutral conductor must be identified by a white cover.

If your outlet looks like this:

3-wire receptacle (10-30R)

Then choose a 3-wire power supply cord with ring or spade terminals and UL listed strain relief. The 3-wire power supply cord, at least 4 ft (1.22 m) long, must have three 10-gauge copper wires

and match a 3-wire receptacle of NEMA Type 10-30R. If connecting by direct wire: Power supply cable must match power supply (4-wire or 3-wire)

and be:

• Flexible armored cable or nonmetallic sheathed copper cable (with ground wire), protected with flexible metallic conduit. All current-carrying wires must be insulated.

• 10-gauge solid copper wire (do not use aluminum).

• At least 5 ft (1.52 m) long.

Electrical Shock Hazard

Plug into a grounded 4 prong outlet. Failure to do so can result in death or electrical shock.

It is your responsibility

• To contact a qualified electrical installer.

• To be sure that the electrical connection is adequate and in conformance with the Canadian Electrical Code, C22.1-latest

edition and local codes. A copy of the above codes standard may be obtained from: Canadian Standards Association, 178 Rexdale Blvd., Toronto, ON M9W 1R3 CANADA.

To supply the required 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply on a separate 30-amp circuit,

fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect to an individual branch

circuit. This dryer is equipped with a CSA International Certified

Power Cord intended to be plugged into a standard 14-30R wall receptacle. The cord is 5 ft (1.52 m) in length. Be sure wall receptacle is within reach of dryer's final location.

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected washer/dryer:

This washer/dryer must be grounded. In the event of

malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This washer/dryer uses a cord having an equipment-grounding conductor and a grounding plug. The

plug must be plugged into an appropriate outlet that is

properly installed and grounded in accordance with all local codes and ordinances.

[] For a permanently connected washer/dryer:

This washer/dryer must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on the washer/dryer.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or

personnel if you are in doubt as to whether the washer/dryer

is properly grounded. Do not modify the plug on the power supply cord: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

4-wire receptacle 14-30R

• Do not use an extension cord. If you are using a replacement power supply cord, it is

recommended that you use Power Supply Cord Replacement Part Number 9831317. For further information, please reference

the service numbers located in the Washer/Dryer User Instructions.

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected washer/dryer: This washer/dryer must be grounded. In the event of

malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for

electric current. This washer/dryer is equipped with a cord having an equipment-grounding conductor and a grounding

plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with

all local codes and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the washer/dryer is properly grounded. Do not modify the plug provided with the washer/dryer: if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

Power Supply Cord

Direct Wire

Fire Hazard

Use a new UL listed 30 amp power supply cord. Use a UL listed strain relief.

Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center

terminal (silver).

Ground wire (green or bare wire) must be connected to green ground connector.

Connect remaining 2 supply wires to remaining 2 terminals (gold).

Securely tighten all electrical connections. Failure to do so can result in death, fire, or

electrical shock.

1. Disconnect power. 3.

2. Remove the hold-down screw and terminal block cover.

A •

Fire Hazard

Use 10 gauge solid copper wire. Use a UL listed strain relief.

Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center

terminal (silver).

Ground wire (green or bare wire) must be connected to green ground connector.

Connect remaining 2 supply wires to remaining 2 terminals (gold).

Securely tighten all electrical connections. Failure to do so can result in death, fire, or

electrical shock.

Install strain relief. Style 1: Power supply cord strain relief

Remove the screws from a 3/4"(1.9 cm) UL listed strain relief (UL marking on strain relief). Put the tabs of the two clamp sections into the hole below the terminal block opening so that one tab is pointing up and the other is pointing down, and

hold in place. Tighten strain relief screw enough to hold the two clamp sections together.

E D

A. Center, silver-colored terminal block screw

B. Hold-down screw

C. Terminal block cover D. Neutral ground wire

E, External ground conductor screw

A. Strain relief tab pointing up B. Hole below terminal block opening C. Clamp section D. Strain relief tab pointing down

;....................................................A

Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the

strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Do not further tighten strain relief screws at this point.

Electrical Connection Options

If your home has: And you will be Go to Section

connecting to:

4-wire receptacle A UL listed, 4-wire connection: (NEMA Type 14-30R) 120/240 volt Power supply cord

30-amp, dryer

_.._ minimum,

power supply cord*

4-wire direct A fused 4-wire connection:

disconnect or Direct Wire circuit breaker

(12.7 cm)

box*

Style 2: Direct wire strain relief

Unscrew the removable conduit connector and any screws from a 3/4"(1.9 cm) UL listed strain relief (UL marking on strain relief). Put the threaded section of the strain relief through the

hole below the terminal block opening. Reaching inside the terminal block opening, screw the removable conduit

connector onto the strain relief threads.

A. Removable conduit connector B. Hole below terminal block opening

C. Strain relief threads

Put direct wire cable through the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a

horizontal position. Tighten strain relief screw against the direct wire cable.

3-wire receptacle A UL listed, (NEMA type 10-30R) 120/240 volt

3-wire connection:

Power supply cord

30-amp, dryer power supply

minimum,

cord*

3-wire direct A fused 3-wire connection:

disconnect or Direct Wire box*

circuit breaker

*If local codes do not permit the connection of a cabinet-ground

conductor to the neutral wire, go to "Optional 3-wire connection" section.

4-wire connection: Power supply cord

IMPORTANT: A 4-wire connection is required for all mobile

homes and where local codes do not permit the use of 3-wire connections.

A /

C D E G

A. 4-wire receptacle (NEMA type 14-30R)

B.4-prong plug C. Ground prong D. Neutral prong

E. Spade terminals with upturned ends

E _" (1.9 cm) UL Iistedstrain relief G. Ring terminals

Now complete installation following instructions for your type of electrical connection:

4-wire (recommended) 3-wire (if 4-wire is not available)

Remove center, silver-colored terminal block screw.

Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white

or center wire) of power supply cord under center, silver- colored terminal block screw. Tighten screw.

A B

A. Neutral ground wire

B. Center silver-colored terminal block screw

C. External ground conductor screw D. Neutral wire (white or center)

E. ¾" (1.9 cm) UL Iisted strain relief

Connect ground wire (green or bare) of power supply cord to external ground conductor screw. Tighten screw.

4-wire connection: Direct Wire

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit the use of 3-wire connections.

Direct wire cable must have 5 ft (1.52 m) of extra length so washer/dryer can be moved if needed.

Strip 5" (12.7 cm) of outer covering from end of cable, leaving bare ground wire at 5" (12.7 cm). Cut 11/2'' (3.8 cm) from 3 remaining wires. Strip insulation back 1" (2.5 cm). Shape ends of wires into a hook shape.

(12.7 C

When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw, as shown.

C .............

B __ ' E

A. External ground conductor screw B. Ground wire (green or bare) of power supply cord C. Neutral ground wire

D. Center silver-colored terminal block screw

E.Neutral wire (white or center) F. 3/4"(1.9 cm) UL ilsted strain relief

4. Connect the other wires to outer terminal block screws. Tighten screws.

5. Tighten strain relief screws.

6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

7. You have completed your electrical connection. Now go to "Venting Requirements."

Remove center, silver-colored terminal block screw.

Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and place the hooked end (hook facing right) of the neutral wire (white or center wire) of

direct wire cable under the center screw of the terminal block. Squeeze hooked ends together. Tighten screw.

A. Neutral ground wire B. Center silver-colored terminal block screw

C. External ground conductor screw D. Neutral wire (white or center wire)

E.3/4'' (1.9 cm) UL ilsted strain relief

Connect ground wire (green or bare) of direct wire cable to external ground conductor screw. Tighten screw.

C D

A. External ground conductor screw

B. Ground wire (green or bare) of power supply cord

C. Neutral ground wire

D. Center silver-colored terminal block screw E. Neutral wire (white or center)

F. 3/4"(1,9 cm) UL Iisted strain relief

Place the hooked ends of the other power supply cable wires under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws.

!! !!

Loosen or remove center, silver-colored terminal block screw.

Connect neutral wire (white or center wire) of power supply cord to the center, silver-colored terminal screw of the terminal

block. Tighten screw.

A. External ground conductor screw B. Neutral ground wire

C. Center silver-colored terminal block screw D. Neutral wire (white or center wire)

E. ¾" (1.9 cm) UL listed strain relief

3. Connect the other wires to outer terminal block screws. Tighten screws.

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

6. You have completed your electrical connection. Now go to "Venting Requirements."

5. Tighten strain relief screw.

6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

7. You have completed your electrical connection. Now go to "Venting Requirements."

3-wire connection: Power supply cord

Use where local codes permit connecting cabinet-ground conductor to neutral wire.

G F

A.3-wire receptacle (NEMA type 10-30R) B.3-wire plug C.Neutralprong D.Spade terminalswith up turned ends E. _" (1.9cm) UL listed strain relief

F.Ring terminals

G.Neutral (white or center wire)

3-wire connection: Direct Wire

Use where local codes permit connecting cabinet-ground conductor to neutral wire.

Direct wire cable must have 5 ft (1.52 m) of extra length so washer/dryer can be moved if needed.

Strip 31/2'' (8.9 cm) of outer covering from end of cable. Strip insulation back 1" (2.5 cm) If using 3-wire cable with ground wire, cut bare wire even with outer covering. Shape ends of wires into a

hook shape.

When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right),

squeeze hooked end together and tighten screw, as shown.

Loosen or remove center, silver-colored terminal block screw.

Place the hooked end of the neutral wire (white or center wire) of direct wire cable under the center screw of terminal block

(hook facing right). Squeeze hooked end together. Tighten screw.

A. External ground conductor screw B. Neutral ground wire C. Center silver-colored terminal block screw

D. Neutral wire (white or center wire) E. _" (1.9 cm) UL listed strain relief

Place the hooked ends of the other power supply cable wires under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws.

!! !!

4. Tighten strain relief screw.

5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

6. You have completed your electrical connection. Now go to "Venting Requirements."

Optional 3-wire connection

Use for direct wire or power supply cord where local codes do not permit connecting cabinet-ground conductor to neutral

wire.

1. Remove center, silver-colored terminal block screw.

2. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white

or center wire) of power supply cord/cable under center, silver-colored terminal block screw. Tighten screw.

A. External ground conductor screw

B. Neutral ground wire

C. Neutral wire (white or center wire)

D. Grounding path determined by a qualified electrician E. _" (1.9 cm) UL Iisted strain relief

Connect the other wires to outer terminal block screws. Tighten screws.

!! !!

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

6. Connect a separate copper ground wire from the external ground conductor screw to an adequate ground.

Fire Hazard

Use a heavy metal vent. Do not use a plastic vent.

Do not use a metal foil vent. Failure to fellow these instructions can result in death

or fire.

WARNING: To reduce the risk of fire, this washer/dryer

MUST BE EXHAUSTED OUTDOORS. IMPORTANT: Observe all governing codes and ordinances.

The dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling or a concealed space of a building.

If using an existing vent system

• Clean lint from the entire length of the system and make sure exhaust hood is not plugged with lint.

• Replace any plastic or metal foil vent with rigid or flexible heavy metal vent.

• Review Vent system chart. Modify existing vent system if necessary to achieve the best drying performance.

If this is a new vent system

Rigid metal vent

• For best drying performance, rigid metal vents are recommended.

• Rigid metal vent is recommended to avoid crushing and kinking.

Flexible metal vent

• Flexible metal vents are acceptable only if accessible for cleaning.

• Flexible metal vent must be fully extended and supported when the dryer is in its final location.

• Remove excess flexible metal vent to avoid sagging and kinking that may result in reduced airflow and poor

performance.

• Do not install flexible metal vent in enclosed walls, ceilings or floors.

Elbows

45° elbows provide better airflow than 90° elbows.

Good Better

Clamps

Use clamps to seal all joints. Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into the interior of the duct. Do not use duct tape.

Vent material

• Use a heaw metal vent. Do not use plastic or metal foil vent.

• 4" (10.2 cm) heavy metal exhaust vent and clamps must be used. DURASAFF Mventing products are recommended.

4" (10.2cm) heavymetal exhaust vent

DURASAFE TM vent products can be purchased from your dealer or by calling Whirlpool Parts and Accessories. For more information, see the "Assistance or Service" section of the

Washer/Dryer User Instructions.

Clamp

Exhaust

Recommended hood styles are shown here.

(10.2 era)

A. Louvered hood style

B.Box hood style

The angled hood style (shown here) is acceptable.

(1 0.2 cm)__

P"_,_ 21/2''

(6.4 crn)

• An exhaust hood should cap the vent to keep rodents and insects from entering the home.

• Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that may be in the path of the exhaust (such as flowers, rocks or bushes, snow line, etc.).

• Do not use an exhaust hood with a magnetic latch.

improper venting can cause moisture and lint to collect indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint, wallpaper,

carpets, etc.

[] Housecleaning problems and health problems.

Excessive Weight Hazard

Use two or more people to move and install washer/dryer.

Failure to do so can result in back or other injury.

To avoid floor damage, set washer/dryer onto cardboard before moving across floor. Move washer/dryer close to its final location.

1. Do not cut yellow strap. Pull yellow strap firmly, until completely removed from washer/dryer. There should be

2 cotter pins on the end of the shipping strap. Remove the hang tag and pin from the vent pipe.

Install the front leveling feet

1. Prop up the front of the washer/dryer about 4" (10.2 cm) with

a wood block or similar object. The block needs to support the weight of the washer/dryer.

2. Screw the Iocknut onto each foot to within 1" (2.5 cm) of the base.

1 "

(2.5 cm)

'_ jr

Screw the feet into the correct holes at the front corner of the washer/dryer until the nuts touch the washer.

NOTE: Do not tighten the nuts until the washer/dryer is level.

Tilt the washer/dryer back and remove the wood block. Gently lower the washer/dryer to the floor.

Proper connection of the drain hose protects your floors from damage due to water leakage. To keep the drain hose from

coming off or leaking, it must be installed according to the following instructions:

iMPORTANT: To ensure proper installation, this procedure must be followed exactly.

1. Check the drain hose to see whether it is the proper length.

2. Wet the inside of the straight end of the drain hose with tap water.

iMPORTANT: Do not use any lubricant other than water.

3. Squeeze ears of the silver, double-wire clamp with pliers to open. Place clamp over the straight end of the drain hose

1A"(6.4 mm) from the end.

2. Tilt the washer/dryer forward. Move each of the 2 rear legs in an up-down motion to check the self-adjusting leveling legs

for free movement. This is required for proper leveling. Gently lower the washer/dryer to the floor.

3. Cut the shipping strap about 16" (40,6 cm) from the plug end. Look for the words "CUT HERE." Discard end with cotter pins.

You will use the remaining piece of shipping strap to secure the drain hose.

4 rnrn)

4. Open clamp. Twist hose back and forth while pushing onto drain connector on the side of the washer/dryer. Continue until hose contacts the ribbed stops on the cabinet.

5. Place clamp over the area marked "CLAMP" Release clamp.

For laundry tub or standpipe drain systems

1. Make sure drain hose form is in correct position.

A. Drain hose form

2. Put hooked end of drain hose into laundry tub or standpipe. Rotate hook to eliminate kinks.

To keep drain water from going back into the washer:

• Do not force excess drain hose into standpipe. Hose should be secure but loose enough to provide a gap for air.

• Do not lay excess hose on the bottom of the laundry tub.

For use with floor drain

Do not install the drain hose form onto the corrugated drain hose. You may need additional parts. See Floor drain under "Tools and

Parts."

Insert a new flat washer into each end of the inlet hoses. Firmly seat the washers in the couplings.

Connect the inlet hoses to the washer

1. Attach the hot water hose to the bottom inlet valve. Attaching

the hot water hose first makes it easier to tighten connection with pliers.

2. Screw on coupling by hand until it is seated on the washer.

3. Using pliers, tighten the couplings with an additional two- thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result.

In the U.S.A.

A. Cold water inlet valve (top) B. Hot water inlet valve (bottom)

In Canada

A B

A. Coupling

B. Washer

Connect the inlet hoses to the water faucets Make sure the washer basket is empty.

1. Attach hose to the hot water faucet. Screw on coupling by hand until it is seated on the washer.

2. Attach hose to the cold water faucet, Screw on coupling by hand until it is seated on the washer.

3. Using pliers, tighten the couplings with an additional two- thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result,

Clear the water lines

• Run water through both faucets and inlet hoses, into a bucket or laundry tub, drainpipe or bucket to get rid of particles in the water lines that might clog the inlet valve screens.

• Check the temperature of the water to make sure that the hot water hose is connected to the hot water faucet and that the

cold water hose is connected to the cold water faucet.

A. Cold water inlet valve (top) B. Hot water inlet valve (bottom)

4. Attach the cold water hose to the top inlet valve.

5. Screw on coupling by hand until it is seated on the washer.

6. Using pliers, tighten the couplings with an additional two- thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result.

If you are working in a closet or recessed area Move the washer/dryer into its final location and remove

cardboard from under washer/dryer. Remove the access panel by removing 3 Phillips-head screws and one bumper, located at the top of the access panel. Set panel, screw, and bumper aside. Complete hookup of water hoses. Replace access panel upon completion of washer/dryer installation.

Check for leaks

• Turn on the water faucets and check for leaks. A small amount of water might enter the washer. You will drain this water later.

NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record hose installation or replacement dates for

future reference.

• If you connect only one water hose, you must cap off the remaining water inlet port.

• Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found.

• The apparatus must be connected to the water faucets using the new hoses. Do not use old hoses.

1. Move the washer/dryer to its final location and remove any cardboard used to move the washer/dryer.

2. Locate the remaining piece of shipping strap. See "Remove Shipping Strap."

Shipping strap

Wrap the drain hose to the laundry tub leg or standpipe with the shipping strap (A or B below). Push fastener into the

nearest hole in the shipping strap (see illustration above).

Optional exhaust installations

This washer/dryer can be converted to exhaust out the right or left side. To convert the washer/dryer, use Side Exhaust Kit

Part Number 279823. If your washer/dryer was previously exhausted from the right or left side, it can be converted to rear exhaust by using standard offset connections. To cover the hole in the side, one of the following plugs can be added:

692790 (white) 3977784 (biscuit)

Follow the instructions in the kit to install. Kits are available from the dealer from whom you purchased your washer/dryer.

If the water faucets and the drain standpipe are recessed, put the hooked end of the drain hose in the standpipe. Tightly wrap the shipping strap around the water inlet hoses and the drain hose (C above). Push fastener into the nearest hole in

the shipping strap (see illustration above).

Choose your exhaust installation type

Recommended exhaust installations

Typical installations vent the dryer from the rear of the washer/ dryer. Other installations are possible.

A B

A.Standard rear offset exhaust installation B.Rear exhaust for offset close clearanceconnection

C.Left or right side exhaust installation

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for your installation. Three close-clearance installations are shown. Refer to the manufacturer's instructions provided with the vent system.

r j_[ ...... ,

", l

"\ i ......... ,j .................

A B C

A. Loop system with standard elbows B. Loop system with one offset and one standard elbow C. Vent system with one periscope (2" [5 cm] clearance)

A. Dryer B. Rigid metal or flexible metal vent C. Clamps

D. Wall

E.Elbow F Clamps

G. Elbow H. Exhaust hood

NOTE: The following kits for close clearance alternate installations are available for purchase. Please reference the "Assistance or Service" section of the Washer/Dryer User Instructions.

• Over-the-Top Installation: Part Number 4396028

Periscope Installation (For use with dryer vent to wall vent mismatch):

Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm) mismatch Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm)

mismatch Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm)

mismatch

+ 30 hidden pages