MER5752AAW
Maytag MER5752AAW, MER5752AAS, MER5752AAQ, MER5752AAB, MER5751AAW Owner’s Manual
...
E_ectric Range -
Tabme of Contents
Safety .......................................... 1-4
Surface Cooking ...................... 5-7
Controls
Smoothtop Surtace
Oven Cooking ......................... 8-15
Baking
Cook & Hold
Delay
Keep Warm
Broiling
Oven Racks
Care & Cleaning ................... 16-19
Self-Cban Oven
Charting Procedures
Maintenance ......................... 20-21
Oven Window
Oven Light
Troubleshooting ................... 21 =22
Warranty & Service .................... 23
Guide d'utilisation et
d'entretien ................................... 24
Guia de Uso y Cuidado ............. 50
Form No. B/10/04 Pall: No. 8113P4g0 60 @2004 Maytag Appliances Sales Co. Litho U.S.A.
installer: Please leavethis manual with this appfiance.
Consumer: Please read and keep this manual for future
reference. Keepsales receipt and/or canceled check as proof
of purchase.
Model Number
Serial Number
Date of Purchase
If _ou have questions, call:
Maytag Customer Assistance
1-800-688-9900 USA
1-800-688-2002 Canada
1-800-688-2080 ( U.S.FRYfor hearing or speech [rnpaired._
(Mon.-Fri.. 8 am-8 pm Eastern Time]
Internet: http://www.maytag.com
tnourcontinu ngeffortto irnprove the quafityand performance
ofour cooking products.it may be necessaryto make changes
to the appfiance without revising this guide.
For service i#fermaden, see page 23.
Warning and Important Safety Instructions appearing in
this guide are not meant to cover aJJpossible conditions
and situations that may occur. Common sense, caution,
and care must be exercised when installing, maintaining,
or operating the appliance.
Always contact the manufacturer about problems or
conditions you do not understand.
Recognize Safety Symbols, Words, Labels
WARNnNG. Hazards or unsafe practices which
COULD result in severe persona] injury or death.
1=oensure proper and safe operation: Appliance must
be properly installed and grounded by a qualified techni-
cian. Do not attempt to adjust, repair, service, or replace
any part of your appliance unless it is specifically recom-
mended in this guide. All other servicing should be
referred to a qualified servicer.
Always disconnect power to appliance before servicing.
o FOLLOW ALL _NSTALLATli
WARNING: To rednce risk of
tipping of the appliance from
abnormal nsage or by e×cessive
leading of the oven doer, the appliance mnst
be secnred by a properly installed anti.tip
To check if device is properly installed, look underneath
range with a flashlight to make sure one of the rear
leveling legs is properly engaged in the bracket slot. The
anti-tip device secures the rear leveling leg to the floor
when properly engaged. You should check this anytime
the range has been moved.
To Prevent Fire or Smoke
Be sure all packing materials are removed from the
appliance before operating it.
Keep area around appliance clear and free from combus-
tible materials. Flammable materials should not be stored
[n an oven,
Many plastics are vulnerable to heat. Keep plastics away
from parts of the appliance that may become warm or
hot.
To prevent grease fires, do not let cooking grease or other
flammable materials accumulate in or near the appliance.
CAUTION _ Hazards or unsafe practices which
COULD result in minor personal injury.
Read and follow aJJinstructions before using this
appliance to prevent the potential risk of fire, electric
shock, personal injury or damage to the appliance as a
result of improper usage of the appliance. Use appliance
only for its intended purpose as described in this guide.
in Case of Fire
Use dry chemical or foam-type extinguisher or baking
soda to smother fire or flame. Never use water on a
grease fire.
1. Turn off appliance to avoid spreading the flame.
2. NEVER pick up or move a flaming pan.
3. Smother oven fire or flame by closing the oven door.
Child Safety
above an appJJance, Children cJjmbing On the appliance
sedous!y injured,
NEVER leave children alone or unsupervised near the
appliance when it is in use or is still hot. Children should
never be allowed to sit or stand on any part of the appli-
ance as they could be injured or burned.
Children must be taught that the appliance and utensils in
it can be hot. Let hot utensils cool in a safe place, out of
reach of small children. Children should be taught that an
appliance is not a toy. Children should not be allowed to
play with controls or other parts of the appliance.
About Your Appliance
NEVER use an app!!ance as a step to teach cabinets
tean!ng Or sitting On the door, may resu!t in p0ssib!e
tipping of the appliance, breakage of door, and serious
injuries,
To prevent potential hazard to the user and damage to the
appliance, do not use appliance as a space heater to heat
or warm a room. Also, do not use the oven as a storage
area for food or cooking utensils.
Do not obstruct the flow of air by blocking the oven vent.
DO NOT TOUCH HEATING ELEMENTS OR iNTERiOR
SURFACES OF OVEN. Heating elements may be hot even
though they are dark in color, interior surfaces of any
oven become hot enough to cause burns. During and
after use, do not touch, or let clothing or other flammable
materials contact heating elements or interior surfaces of
oven until they have had sufficient time to cool. Other
surfaces of the appliance may become hot enough to
cause burns - among these surfaces are: oven vent
opening, surface near this opening, oven door, and
window of oven door.
Do not touch a hot oven light bulb with a damp cloth as
the bulb could break Should the bulb break, disconnect
power to the appliance before removing bulb to avoid
electrical shock
NEVER use aluminum foil to cover an oven rack or oven
bottom. Misuse could result in risk of electric shock, fire,
or damage to the appliance. Use foil only as directed in
this guide.
Cooking Safety
Never heat an unopened food container in the oven.
Pressure build-up may cause container to burst resulting
in serious personal injury or damage to the appliance.
Use dry, sturdy potholders. Damp potholders may cause
burns from steam. Dish towels or other substitutes should
never be used as potholders because they can trail across
hot elements and ignite or get caught on appliance parts.
Wear proper apparel. Loose fitting or long hanging-
sleeved apparel should not be worn while cooking. Cloth-
ing may ignite and cause burns if garment comes in
contact with heating elements.
Always place oven racks in the desired positions while
oven is cool. Slide oven rack out to add or remove food,
using dry, sturdy potholders. Always avoid reaching into
the oven to add or remove food. If a rack must be moved
while hot, use a dry potholder. Do not let potholder contact
hot element in oven.
Use racks only in the oven in which they were shipped/
purchased.
Use care when opening the oven door. Let hot air or steam
escape before removing or replacing food.
PREPARED FOOD WARNUNG: Follow food
manufacturer's instructions. If a plastic frozen food con-
tainer and/or its cover distorts, warps, or is otherwise
damaged during cooking, immediately discard the food
and its container. The food could be contaminated.
Do not allow aluminum foil or meat probe to contact
heating element.
Always turn off all controls when cooking is completed.
Utensim Safety
Follow the manufacturer's directions when using oven
cooking bags.
This appliance has been tested for safe performance
using conventional cookware. Do not use any devices or
accessories that are not specifically recommended in
this manual. Do not use stove top grills or add-on oven
convection systems. The use of devices or accessories
that are not expressly recommended in this manual can
create serious safety hazards, result in performance
problems, and reduce the life of the components of this
appliance.
Be sure utensil is large enough to properly contain food
and avoid boilovers. Pan size is particularly important in
deep fat frying. Be sure pan will accommodate the
volume of food that is to be added as well as the bubble
action of fat.
Never let a pan boll dry as this could damage the utensil
and the appliance.
If pan is smaller than element, a portion of the element
will be exposed to direct contact and could ignite cloth-
ing or potholder.
Only certain types of glass, glass/ceramic, ceramic,
earthenware, or other glazed utensils are suitable for
cooktop or oven service without breaking due to the
sudden change in temperature. Follow utensil
manufacturer's instructions when using glass.
Turn pan handle toward center of cooktop, not out into
the room or over another surface element. This reduces
the risk of burns, ignition of flammable materials, or
spillage if pan is accldently bumped or reached by small
children.
NEVER leave surface units unattended especially when
using high heat. An unattended bollover could cause
smoking and a greasy spillover can cause a fire.
This appliance is equipped with different size surface
elements. Select pans with flat bottoms large enough to
cover element. Fitting pan size to element will improve
cooking efficiency.
GLASS_CERAMUC SURFACE: NEVER cook on broken
cooktop. If cooktop should break, cleaning solutions and
splllovers may penetrate the broken cooktop and create a
risk of electric shock Contact a qualified technician
immediately.
Deep Fat Fryers
Use extreme caution when moving the grease pan or
disposing of hot grease. Allow grease to cool before
attempting to move pan.
Ventimating Hoods
Clean range hood and filters frequently to prevent grease
or other flammable materials from accumulating on hood
or filter and to avoid grease fires.
When flaming foods under the hood, turn the fan on.
Cleaning Safety
Clean cooktop with caution. Turn off all controls and walt
for appliance parts to cool before touching or cleaning.
Clean with caution. Use care to avoid steam burns if a wet
sponge or cloth is used to wipe spills on a hot surface.
Some cleaners can produce noxious fumes if applied to a
hot surface.
Clean only parts listed in this guide.
Self-Clean Oven
Do not leave racks, broiling pan, food or cooking
utensils, etc. in the oven during the self-clean cycle.
Do not clean door gasket. The door gasket is essential for
a good seal Care should be taken not to rub, damage, or
move the gasket.
Do not use oven cleaners or oven liners of any kind in or
around any part of the self-clean oven.
Before self-cleaning the oven, remove broiler pan, oven
racks and other utensils, and wipe off excessive spillovers
to prevent excessive smoke or flare ups.
It is normal for the cooktop of the range to become hot
during a self-clean cycle. Therefore, touching the
cooktop during a clean cycle should be avoided.
3
l pottant Safety Notice and
The California Safe Drinking Water and Toxic Enforce-
ment Act of 1986 (Proposition 65} requires the Governor
of California to publish a list of substances known to the
State of California to cause cancer or reproductive harm,
and requires businesses to warn customers of potential
exposures to such substances.
Users of this appliance are hereby warned that when the
oven is engaged in the self-clean cycle, there may be
some low-level exposure to some of the listed sub-
stances, including carbon monoxide. Exposure to these
substances can be minimized by properly venting the
oven to the outdoors by opening the window's and/or
door in the room where the appliance is located during
the self-clean cycle.
UMPORTANT NOTUCE REGARDUNG PET BURDS: Never
keep pet birds in the kitchen or in rooms where the
fumes from the kitchen could reach. Birds have a very
sensitive respiratory system. Fumes released during an
oven self-cleaning cycle may be harmful or fatal to birds.
Fumes released due to overheated cooking oil, fat,
margarine and overheated non-stick cookware may be
equafly harmful
Save These instructions for Future Reference
4
Surface Controls
Use to turn on the surface elements. An infinite choice of
heat settings is avaihb[e from Low to High. The knobs can
be set on or between any of the settings.
Setting the ControJs
1. Phce pan on surface dement.
2. Push in and turn the knob in either direction to the desired
° The control pane[ is marked to identify wNch O O
dement the knob controls. For example, the
graphic at right indicates Heftfront dement. O O
3. There is an dement indicator light on the control pane[.
When any surface control knob isturned on, the light will
turn on. The light will turn off when all the surface ele-
ments are turned off.
4. After cooking, turn knob to OFF. Remove pan.
[}ual Element (select models)
The cooking surface has a dual element
located in the right front position of the
smoothtop. This allows you to change
the size of this element.
1. Press the switch to the left to use
the large element or to the right to
use the small element.
2. Push in and turn knob in either
direction to the desired heat setting.
_OW
2
OFF
High
Medium .....
Suggested Heat Settings
The size, type of cookware and cooking operation will affect
the heat setting. For information on cookware and other
factors affecting heat settings, refer to Cookware Recommen-
dations on page 7 and "Cooking Made Simple" booklet.
Medo Low (3-4):
Use to continue
cooking covered
foods or steam
foods.
Medium (5-7): Use to
maintain slow boil for
large amounts of liquids
and for most frying
operations.
1
High (10): Use to bring
liquid to a boil Always
reduce setting to a lower
heat when liquids begin to
boil or foods begin to cook.
OFF [ Styling may
Hieh vary depending
on model
@
.......Medium ....................
Medo High (8=9): Use
to brown meat, heat oil
for deep fat frying or
sauteing. Maintain fast
boil for large amounts
of liquids.
BEFORECOOKING AFTER COOKING
, Always place a pan on the surface unit before you turn it • Make sure surtace unit is turned off
on, To prevent damage to range, never operate surface
unit without a pan in place,
NEVER use the cooktop as a storage area for food or
cookware,
DURIN6 COOKIN6
Be sure you know which knob controls which surface
• Clean up messy spills as soon as possible,
OTHER TIPS
- tf cabinet storage is provided direct[_ above cooking
surface limit it to items that are infrequendy used and can
be safely stored in an area subjected to heat. Tempera-
tures may be unsafe for items such asvolatile liquids.
unit, Make sure } ou turned on the correct surface unit.... cleaners ol aerosol sprays
Begin cooking on a higher heat setting then reduce to a • NEVER leave any items, especially plastic items, on the
lower setting to complete the operation, Never use a cooktop The hot air from the ven_may ignite flammable
high heat setting for ex_ended cooking, items, melt or soften plastics, or increase pressure in
NBIE@ allow a pan to boil dry.This could damage the dosed con_aiuuerscausing them to burst.
pan and the appliance, o NEVER allow aluminum foil. meat probes or an} other
NEVER touch cooktop until it has cooled, Expect some metal object, other than a pan on a surface elemenL to
parts of the cooktop, especiall_ around the surface units .... contact heating elements.
to become warm or hot during cooking. Use potholders o NEVER store heav} items above the cooktop that could fall
_oprotect hands, and damage it.
5
S oothtop Surface
Smoothtop Surface Notes:
, Cooktop may emit mightsmoke and odor the first few
times the cooktop is used. This is normal
, Smoothtop cooktops retain heat for a period of time
after the element is turned off. Turn the dements off
a few minutes before food is compHeteHycooked and use
the retained heat to compHetecooking. When the hot
surface Hightturns off, the cooking area wiHHbe cooH
enough to touch. Because of the way they retain heat, the
smoothtop dements wiHHnot respond to changes in
settings as quickHyas coiHdements.
° In the event of a potentiaHboiHover,remove the pan from
the cooking surface.
, Never attempt to miftthe cooktopo
° The smoothtop surface may appear discoHoredwhen it is
hot=This is normaHand wiHHdisappear when the surface
cooHs=
Cooking Areas
The cooking areas on your range are identified by permanent
circHeson the smoothtop surface. For most efficient cooking,
fit the pan size to the dement size.
Pans should not extend more than t-inch beyond the
cooking area.
When a control is turned on, a gHowcan be seen through the
smoothtop surface. The element will cycmeon and off to
maintain the preset heat setting, even on Hi.
For more information on cookware, refer to Cookware
Recommendations on page 7 and "Cooking Made Simple"
bookHetincHudedwith your range.
SINGLE
ELEMENTS
Tips to Protect the
Smoothtop Surface
CJeaning (see page 18 for more information}
° Before first use, clean the cooktop.
° Clean your cooktop daily or after each use. This will keep
your cooktop looking good and can prevent damage.
° If a spillover occurs while cooking, immediately clean the
spill from the cooking area while it is hot to prevent a tough
cleaning chore later. Using extreme care, wipe spill with a
clean dry towel
° Do not allow spills to remain on the cooking area or the
cooktop trim for a long period of time.
° Never use abrasive cleansing powders or scouring pads
which will scratch the cooktop.
° Never use chlorine bleach, ammonia or other cleansers not
specifically recommended for use on glass-ceramic.
To Prevent Marks and Scratches
° Do not use glass pans. They may scratch the surface.
° Never place a trivet or wok ring between the surface and
pan. These items can mark or etch the top.
° Do not slide aluminum pans across a hot surface. The pans
may leave marks which need to be removed promptly. (See
Cleaning, page 18=}
° Make sure the surface and the pan bottom are clean before
turning on to prevent scratches.
° To prevent scratching or damage to the glass-ceramic top,
do not leave sugar, salt or fats on the cooking area. Wipe
the cooktop surface with a clean cloth or paper towel
before using.
° Never slide heavy metal pans across the surface since
these may scratch.
cent.
DUAL ELEMENT
(SELECT MODELS)
Hot Surface Light
The Hot Surface indicator Hightis Hocatedon the
controHpanel The HightwiHHbe iHHuminated
Hef_ Surface
when any cooking area is hot= It wiHHremain on,
even after the controHisturned off, untiHthe area has cooHed=
6
To Prevent Stains
, Never use a seineddish cloth or sponge to dean the
cooktop surface. A fiim will remain which may cause stains
on the cooking surface after the area is heated.
, Condnuousiy cooking on a seinedsurface may/will resuit in
a permanent stain.
To Prevent Other Damage
° Do not allow piasdc, sugar or foods with high sugar content
to meit onto the hot cooktop. ShouM this happen, dean
immediatdy. (See Cbaning, page 18.}
° Never Neta pan boii dry as this will damage the surface and
pan.
, Never use cooktop as a work surface or cutting board.
° Never cook food directly on the surface.
° Do not use a small pan on a large element. Not only does
this waste energy, but it can also result in spillovers burning
onto the cooking area which requires extra cleaning.
, Do not use non-fiat specialty items that areoversized or
uneven such as round bottom woks, rippled bottom and/or
oversized canners and griddles.
° Do not use foil or foiPtype containers. Foil may melt onto
the glass. If metal melts on the cooktop, do not use. Call an
authorized Maytag Servicer.
Cookware Recommendations
Using the right cookware can prevent many problems, such
as food taking longer to cook or achieving inconsistent
results. Proper pans will reduce cooking times, use less
energy, and cook food more evenly.
Nat Pan Tests
See if your pans are flat.
The Rumor Test:
1. Place a ruler across the bottom of the pan.
2. Hold it up to the light.
3. Little or no light should be visible under the ruler.
The Bubble Test:
1. Put 1 inch of water in the pan. Place on cooktop and turn
control to High,
2. Watch the formation of the bubbles as the water heats.
Uniform bubbles mean good performance, and uneven
bubbles indicate hot spots and uneven cooking.
See "Cooking Made Simpie" bookiet for more information.
Select • Avoid
Flat,smooth-bottom Panswith grooved orwarped bottoms.
)ans. Panswith uneven bottoms do not cook
efficiently and sometimes may not
boil liquid.
Heavy-gauge pans, Very thin-gauge metal or glass pans,
Pansthat are the Pans smaller or larger than the
same size as the element by' 1 inch.
dement.
Secure handles. Cookware with looseor broken handles.
Heavyhandles that tilt the pan.
Loose-fitting lids.
Hat bottom woks. Woks with a ring-stand bottom.
Canning and Oversize
All canners and large pots must have fiat bottoms and
must be made from heavy-gauge materials. This is critical
on smoothtop surfaces. The base must not be more than
1 inch larger than the element.
When canners and pots do not meet these standards, cooking
times may be longer, and cooktops may be damaged.
Some canners are designed with smaller bases for use on
smoothtop surfaces.
When canning, use the High heat setting only until the
water comes to a boil or pressure is reached in the canner.
Reduce to the lowest heat setting that maintains the boil or
pressure. If the heat is not turned down, the cooktop may be
damaged.
See "Cooking Made Simple" booklet for more information.
C D
Less- ...............
E F G H 1 j
The control panel isdesigned for easein programming. Thedisplaywindow on thecontrol shows time of day,timer and ovenfunctions.
Control panel shown includes model specific features. (Styling may vary depending on modeL}
A
B
C
D
e
F
N
J
Broil
Bake
More+ or
Less-
Timer
Cook & Hold
Clean
Delay
Clock
Keep Warm
CANCEL
Use for broiling and top browning.
Use for baking and roasting.
Enters or changes time, oven
temperature. Sets Hi or LO broil
Sets Timer.
Bakes for a preset time, then holds food
warm for 1 hour.
Use to set self-clean cycle.
Programs the oven to start baking at
a later time.
Use to set time-of-day clock.
Use to keep cooked food warm in oven.
Cancels all operations except Timer
and Clock.
Using the Touchpads
Pressthe desired pad.
Pressthe More+ or Less- pad to enter time or temperature.
° A beep wiii sound when any pad is touched.
° A double beep wiii sound if a programming error occurs.
Note: Fourseconds after pressing the More+ or Less-
pad, the time or temperature will automatically be entered.
If more than 30 seconds elapse between touching a
function pad and the More+ or Less- pad, the function will
be canceled and the display will return to the previous
display.
The clock can be set to display time in a 12-hour or 24-hour
format. The clock is set at the factory for the 12-hour format.
To change the clock to 24-hour format:
1. Pressand hold the CANCEL and Delay
pads for three seconds.
2. Pressthe More+ or Less - pad to select
12 or 24 hour.
3. Set the time of day following the
directions below.
To set the Clock:
1. Pressthe Clock pad.
° Time of day and the colon flash in the
display.
2. Pressthe More+ or Less- pad to set the
time of day.
° Colon continues flashing.
3. Pressthe Clock pad again or wait four
seconds.
Less- :
When electrical power is supplied or after a power interrup-
tion, the last clock time before power was interrupted will
flash.
To recall the time of day when another time function is
showing, press the Clock pad.
Clock time cannot be changed when the oven has been
programmed for cook or clean Delay or Cook & Hold.
8
To cancel the Clock display:
If you do not want the time of day to dispHay:
Press and hoM the CANCEL and CHock
pads for three seconds. The time of day
wifl disappear from the dispHay
When the chockdispHayis cancelled, press
the CHockpad to briefly dispHaythe time
of day=
To restore the CJoek display:
Press and hoHdthe CANCEL and CHockpads for three sec-
onds. The time of day will reappear in the dispHay=
The timer can be set from one minute (00:01] up to 99 hours
and 59 minutes (99:59].
The timer can be used independentHy of any other oven
activity. It can aHsobe set while another oven function is
operating.
The Timer does not control the oven. It only controls a
beeper.
To set the Timer:
1. Press the Timer pad. FrTler
,0:00 lights in the display.
, The colon flashes in the display.
2. Press the More+ or Less- pad until the
correct time appears in the display. Less-
.........................................
_The colon will continue to flash.
3. PressTimer pad again or wait four seconds.
, The colon continues flashing and the time begins
counting down.
, The last minute of the timer countdown will be displayed
as seconds.
4. At the end of the set time, one long beep will sound.
To cancel the Timer:
1= Press and hold the Timer pad for three seconds.
OR
2= Pressthe Timer pad and set the time to 00:00=
Locking the ControJ
The touchpad controls can be locked for safety, cleaning, or
to prevent unwanted use= They will not function when locked.
If the oven is currently in use, the controls cannot be locked.
The current time of day will remain in the display when the
controls are locked.
To took:
Press and hold the CANCEL and Cook &
Hold pads for three seconds.
LOCKflashes in the display.
To unlock:
Press and hold the CANCEL and Cook &
Hold pads for three seconds.
LOCKdisappears from the display.
FauJt Codes
BAKE or LOCK may flash rapidly in the display to alert you if
there is an error or a problem. If BAKE or LOCK flash in the
display, press CANCEL pad= If BAKE or LOCKcontinue to
flash, disconnect power to the appliance. Wait a few minutes,
and then reconnect power=If the flashing still continues,
disconnect power to the appliance and call an authorized
servicer.
9
To set Bake:
1. Press the Bake pad.
° "BAKE" will flash.
° 000 will Nightin the display.
2. Select the oven temperature. The oven tempera- More+
ture can be set from 170° to 550°. Pressor press .........................................
and hold the More+ or Less- pads. .........
Less
° 350°will Nightwhen either pad is first pressed. ............................................
° Press the More+ pad to increase the temperature.
° Press the Less- pad to decrease the temperature.
3. Press Bake pad again or wait four seconds.
° BAKEwiii stop flashing and light in the display.
° 100° or the actual oven temperature wiii display. The
temperature will rise in 5° increments until the preset
temperature is reached.
4. Allow the oven to preheat for 8-15 minutes.
° When the set oven temperature is reached, one long
beep will sound.
° To recall the set temperature during preheat, press the
Bake pad.
5. Place food in center of oven, allowing a minimum of two
inches between utensil and oven walls.
8. Check cooking progress. Cook longer if needed.
7. When cooking is finished, press CANCEL.
8. Remove food from the oven.
Baking Notes:
To change oven temperature during cooking, press
the Bake pad, then press the More+ or Less- pad until
the desired temperature is displayed.
To change oven temperature during preheat, press
the Bake pad twice, then press the More+ or Less- pad
until the desired temperature is displayed.
If you forget to turn off the oven, it will automatically turn
off at the end of 12 hours. If you wish to deactivate this
feature, see page 13.
For additional baking and roasting tips, see "Cooking
Made Simple" booklet.
Baking Differences Between Your
and New Oven
It is normal to notice some baking time differences between a
new ovenand an old one. See"Adjusting the OvenTemperature"
on page 13.
Cook & Hold
cook & Hold allows you to bake for a preset amount of time,
followed by aone-hour Keep Warm cycle.
TO set Cook & Hemal:
1. Pressthe Cook & Hold pad.
, "BAKE" and "HOLD" flash.
, 000 lights in the display.
2. Select the oven temperature. The oven tempera-
ture can be set from 170° to 550°. Press or press ....................................
Less )
and hold the More+ or Less- pad,
, Pressthe More+ pad to increase the temperature.
, Pressthe Less- pad to decrease the temperature.
3. Press Cook & Hold again ORwait four seconds.
, "HOLD" flashes.
, 00:00 flashes in the display.
4. Enter the amount of time you want to bake by pressing the
More+ or Less- pad. Bake time can be set from ten
minutes (00:10} to 11 hours, 59 minutes (11:59}.
° "BAKE" and "HOLD" light in the display.
° The baking time wiii light in the display.
° The baking time wiii start counting down.
When the cooking time has elapsed:
° Four beeps wiii sound.
° "BAKE" wiii turn off.
° "HOLD" and "WARM" will light.
° 170°will display.
After one hour in HOLD WARM:
, "End" will display,
° The time of day reappears in the display.
To cancel Cook & Hold at any time: (CANCkL')
Press the CANCEL pad. Remove food from oven.
10
Delay Bake
as dairy products, pork, poultry, or seafood,
When using Delay, the oven begins to cook later in the day.
Set the amount of time that you want to delay before the oven
turns on and how long you want to cook. The oven begins to
heat at the selected time and cooks for the specified length of
time, then keeps food warm for up to one hour.
Delay time can be set from 10 minutes (00:10} to 11 hours, 59
minutes (11:59}.
To set a Delayed Baking cycle:
1. Pressthe Delay pad.
° "DELAY" flashes.
° 00:00 flashes in the display.
2. Pressthe More+ or Less- pad to set the
delay time.
While "DELAY" is still flashing:
3. Pressthe Cook & Hold pad.
° 000 lights in the display.
° "BAKE" and "HOLD" flash.
4.
Press More+ pad to set the baking temperature.
° 00:00 and "HOLD" flash.
° "BAKE" stays ill
Press More+ pad to set the baking time.
° The Delay time, "DELAY", "BAKE" and "HOLD" light in
the display.
When the Delay time has expired:
° "DELAY" will turn off.
° Baking time is displayed.
° "BAKE" and "HOLD" are displayed.
To set a Delay when Cook & Hold has already
been programmed:
1. Pressthe Delay pad.
° "DELAY" flashes.
° 00:00 appears in the dispHay. .........................
2. Pressthe More+ or Less- pad to set the
delay time.
° After four seconds, "DELAY" wiii Less-
stay lit to remind you that a delayed ..............................
cooking cycle has been set.
When the Delay time has expired and the oven
starts:
° The baking time will be dispHayed.
° "DELAY" will turn off.
° "BAKE" and "HOLD" will remain Hit.
To cancel:
Press the CANCEL pad.
, All timed and untimed cooking functions will be
canceled.
, The time of day will reappear in the dispHay.
_otes;:
Do not use delayed baMng for items that require a
preheated oven, such as cakes, cookies, and breads.
Do not use ddayed baking if oven is already hot.
11
Keep Warm
Forsafdy keephg foods warm or for warmhg breads and
pHates=
To set Keep Warm:
1= Press the Keep Warm pad=
° "WARM" flashes,
° 000 appears in the dispHay..................................
2, SeHectthe Keep Warm temperature, The Keep
Warm temperature can be set from 145° to ..................................
190°` Pressor press and hoHdthe More+ or
Less- pad, Less-
, 170° will Hightwhen either pad is first pressed,
, Press the More+ pad to increase the temperature,
, Press the Less- pad to decrease the temperature,
"WARM" and the temperature will be dispHayedwile Keep
Warm is active,
Keep Warm Notes:
, Foroptimal food quality, oven cooked foods should be kept
warm for no longer than 1 to 2 hours,
, To keep foods from drying, cover loosely with foil or a Hid,
, To warm dinner rolls:
- cover rolls loosely with foil and place in oven,
- press Keep Warm and More+ pads to set 170° R
- warm for 12-15 minutes,
, To warm pmates:
- place 2 stacks of up to four plates each in the oven,
- press Keep Warm and More+ pads to set 170° R
- warm for five minutes, turn off the oven and leave plates
in the oven for 15 minutes more,
- use only oven-safe plates, check with the manufacturer,
- do not set warm dishes on a cold surface as rapid
temperature changes could cause crazing or breakage,
To cancem Keep Warm:
1, Pressthe CANCEL pad,
2, Removefood from the oven,
12
Automatic Shut-Off/Sabbath
Mode
The oven will automatically turn off after 12 hours if you
accidentally Heaveit on. This safety feature can be turned off.
TO cancel the 12-hour shut-off and run the
oven eontinuousJy for 72 hours:
1. Set the oven to bake _seepage 10].
2= Press and hoHdthe CHockpad for five seconds.
° SAb will be dispHayedand flash for five seconds.
° SAb will then be dispHayedcontinuousHyuntiHturned off
or until the 72-hour time limit is reached.
° "BAKE" will also be displayed if a bake cycle is in use
while the oven is in Sabbath Mode.
All other functions EXCEPTBAKE (Timer, Keep Warm,
Clean, etc.] are locked out during the Sabbath Mode.
To cancel Bake when in Sabbath Mode:
Press CANCEL.
CANCEL
, "BAKE" will turn off in the display.
° No beeps will sound.
1"0 cancel the Sabbath Mode:
1= Press the Clock pad for five seconds.
OR
2= After 72 hours, the Sabbath Mode will end=
° SAb will flash for five seconds.
° The time of day will return to the display.
Adjusting the Oven Temperature
Oven temperatures are carefully tested for accuracy at the
factory. It is normal to notice some baking or browning
differences between a new oven and an old one= As ranges
get older, the oven temperature can shift.
You may adjust the oven temperature if you think the oven is
not baking or browning correctly. To decide how much to
change the temperature, set the temperature 25° higher or
lower than your recipe recommends, then bake. The results
of the "test" should give you an idea of how much to adjust
the temperature.
To adjust the oven temperature:
1= Press Bake.
2. Enter 550° by pressing the More+ pad.
J
3. Pressand hold the Bake pad for several More+
seconds or until 0° appears in the display. ".............................
If the oven temperature was previously adjusted, the
change will be displayed. Forexample, if the oven tem-
perature was reduced by 15° the display will show "-15 °''-
4. Pressthe More+ or Less- pad to adjust the temperature.
Eachtime a pad is pressed, the temperature changes by
5°- The oven temperature can be increased or decreased
by 5° to 35°-
5. The time of day will automatically reappear in the display.
You do not need to readjust the oven temperature if there
is a power failure or interruption. Broiling and cleaning
temperatures cannot be adjusted.
Sabbath Mode Notes:
° Sabbath Mode can be turned on at any time with or
without the oven on=
° Sabbath Mode cannot be turned on if the touchpads are
locked out or when the door is locked.
, If the oven is baking when Sabbath Mode is set, "BAKE"
will go out at the end of the baking cycle. There will be
no audible beeps.
, When the Sabbath Mode is started, no preheat beep will
sound.
, All prompts, messages and beeps are deactivated when
Sabbath Mode is active.
, Pressing CANCEL will cancel a Bake cycle, however the
control will stay in the Sabbath Mode.
, If power fails, the oven will power up in Sabbath Mode with
72 hours remaining and no cycle active.
13
G
To set Broil:
1. Press the Broil pad.
, "BROIL" flashes.
, SETis displayed.
2. Press the More+ pad to set HI broil or press the Less- pad
to set LO broil.
, Hi or LO will be displayed.
, Sebct HI broil (550° F}for normal broiling. Sebct
LO broil (450° F}for low-temperature broiling of longer
cooking foods such as poultry.
3. After four seconds, the oven will start.
, "BROIL" will remain lit.
4. Foroptimum browning, preheat broil dement for 3-4
minutes before adding food.
5. Placefood in the oven. Leave oven door open about four
inches (the first stop].
6,
7.
Turn meat once about halfway through cooking.
When food is cooked, press the CANCEL
pad. Remove food and broiler pan from the
ove n.
, The time of day wiii reappear in the
display.
Broil Notes:
, For best results when broiling, use a pan designed for
broiling.
° Expect broil times to increase and browning to be
slightly lighter if appliance is installed on a 208-volt
circuit.
, Hi is used for most broiling. Use LO broil when broiling
longer cooking foods. The lower temperature allows
food to cook to the well done stage without excessive
browning.
, Broil times may be longer when the lower broiling
temperature is selected.
° Food should be turned halfway through broiling time.
° For additional broiling tips and temperatures, refer to the
"Cooking Made Simple" booklet.
Broiling Chart
I TOTAL
FOODS POS_TmON* DONENESS I COOK TmME
4
4
4
4
4
4
Medium
Weii Done
Weii Done
Beef
Steak, 1" thick
Hamburgers, 3/4" thick
Pork
Bacon
Chops, 1"
Ham - precooked slice, 1/2" thick
Poultry
Chicken Pieces
Seafood
Fish Steaks, buttered, 1" thick
Fillets
*The top rack position is #5.
Weii Done
Weii Done
Warm
15 - 18 minutes
19 - 23 minutes
15 - 18 minutes
6 - 10 minutes
22 - 26 minutes
8 - 12 minutes
LO Broii
3 or 4 Weii Done 28 - 38 minutes
Flaky
Flaky
10 - 15 minutes
8 - 12 minutes
Note: This chart is a suggested guide. The times may vary with the food being cooked.
14
Oven Vent
When the oven is h use the area near the vent may become
hot enough to cause burns. Never Mock the vent opening.
The oven vent is located below the backgaard vent
shield on your range.
OVEN VENT
L0 CA TION
Do not piace
piasdcs near the
vent opening as
heat from the vent
couid distort or
Oven Light
Press the Oven Light switch on the controi pand to
turn the oven Highton and off.
Oven
Oven Bottom U_ht
Protect oven bottom against spiHovers, espedaHy acidic or
sugar}, spills, as they may discolor the porcelain enamel. Use
the correct pan size to avoid spillovers and boilovers. Do not
place atensils or amaminam foil directly on the oven
bottom.
Oven Racks
To replace:
1= Place rack on the rack support in the oven
2= Tilt the front end up slightly. Slide rack back until it clears
the lock-stop position.
3= Lower front and slide back into the oven.
Do not cover an entire rack with aiaminam foil or place foil
on the oven bottom. Baking resaits will be affected and
damage may occur to the oven bottom.
Rack Positions
RACK 5 Chighest
position:}: Used for
8_
toasting bread or
broiling thin, non-fatty
foods.
RACK 4: Used for
most broiling.
RACK 3: Used for most
baked goods on a
cookie sheet or jelly roll pan, layer cakes, fruit pies, or frozen
convenience foods.
5
__4
--3
__2
--1
RACK 2: Used for roasting small cuts of meat, casseroles,
baking loaves of bread, bundt cakes or custard pies.
RACK 1: Used for roasting large cuts of meat and poultry,
frozen pies, dessert souffles or angel food cake.
MULTIPLE RACK COOKING:
Two rack: Use rack positions 2 and 4, or 1and 4.
- Do net usethe even for storing food or cookware.
The oven has two racks. Ai[ racks are designed with a lock-
stop edge.
To remove:
1. Pui[ rack straight out until it
stops at the lock-stop posi-
tion.
2, Lift up on the front of the rack
and pui[ out,
Half Rack Accessory
A half rack, to increase oven capac-
it}', isavailable as an accesseD,. [t fits
in the left, upper portion of the oven
and provides space for a vegetable
dish when a large roaster is on the
lower rack. Contact your dealer for
the "HALFRACK" Accesser}, Kit or
call 1-800-688-8408.
15
Seff-C ean Oven
o It is normal for parts of the range to become hot dunng a
* To prevent persouai injury and damage to the oven door
do not attempt to open door when "'LOCK"is displayed
, Avoid touching cooktop, door_window or oven veto area
during a clean cycle.
, Do not use commercial oven cleaners on the oven finish
or around any part of the oven. The} wiii damage the
finish o_ parts.
The self-clean cycle uses above-normal cooking temperatures
to automatically clean the oven interior. Do not force the oven
door or lock lever open. This may result in exposure to high
temperatures and be a burn hazard.
It is normal for flare-ups, smoking, or flaming to occur during
cleaning if the oven is heavily soiled. It is better to clean the
oven regularly rather than to wait until there is a heavy build-
up of soil in the oven.
During the cleaning process, the kitchen should be well
ventilated to get rid of normal odors associated with cleaning.
Before Se f-Cmeaning
1. Turn off the oven light before cleaning. The light may burn
out during the clean cycle.
2. Remove broiler pan, all pans, and oven racks from the
oven. The oven racks will discolor and may not slide easily
after a self-clean cycle if they are not removed.
3. Clean oven frame, door frame, area outside of gasket, and
around the opening in the door gasket with a nonabrasive
cleaner such as Bon Ami* or detergent and water. The
self-cleaning process does not clean these areas. They
should be cleaned to prevent soil from baking on during
the clean cycle. (The gasket is the
seal around the oven door and
window.[)
4. To prevent damage, do not clean or
rub the gasket around the oven
door. The gasket is designed to
seal in heat during the clean cycle.
5. Wipe up excess grease or spillovers from the oven bottom.
This prevents excessive smoking, flare-ups or flaming
during the clean cycle.
6. Wipe up sugary'and acidic spillovers such as sweet
potatoes, tomato, or milk-based sauces. Porcelain enamel
is acid-resistant, not acid-proof. The porcelain finish may
discolor if acidic spills are not wiped up before a self-clean
cycle.
To set Self-Clean:
Note: Oven temperature must be below 400° Fto programa dean cycle,
1.
2.
Close the oven door.
Move door lock lever right to the locked position.
3. Pressthe Clean pad.
° "CLEAN" flashes in the display.
If the door is not closed, beeps will sound and "DOOR" will
display. If the door is not closed within 45 seconds, the
self-cleaning operation will be canceled and the display
will return to the time of day.
4. Pressthe More+ or Less- pad.
° "CL-M" (Medium Soil, 3hours} is displayed.
5. Pressthe More+ or Less- pad to scroll through ............................................
the self-cleaning settings. (More+
CL-H" (Heavy Soil, 4 hours}
CL-M" (Medium soil, 3 hours} Jess-
....
CL-L__(Light Soil, 2 hours}
Choosing the soil level of the oven automatically programs
the self-cleaning time.
6. After four seconds, the oven will start cleaning.
, The cleaning time will start counting down in the display.
, "LOCK" will appear in the display.
, "CLEAN" will appear in the display.
To Delay a Self-Cmean Cycle:
1. Pressthe Delay pad.
° "DELAY" flashes.
° 00:00 will appear in the display.
2. Pressthe More+ or Less- pad to set the
amount of time you want to delay the
cycle. Delay time can be set from ten
minutes (00:10} to 11 hours, 59 minutes
(11:5g}.
conto
Brand names for cleaning products are registered trademarks of the respective manufacturers.
16
3. Press the CHeanpad.
, "CLEAN" will flash.
4. Press the More+ or Less- pad. .................
, "CL-M" (Medium Soil 3 hours:)
is dispHayed. ..........................
5. Press the More+ or Less- pad to scroll through the sdf-
cHeaningsettings.
CL-H" (Heavy Soil 4 hours:)
CL-M" (Medium soil 3 hours:)
CL-L" (Light Soil 2 hours:)
Choosing the soiHHevdof the oven automatically programs
the sdf-cHeaning time.
6. After four seconds, CLEAN, DELAY and LOCK will appear
in the dispHayto show that the oven is set for a ddayed
dean operation. The dday time is dispHayed.
Jf the oven has amready been set for a clean
cycle and you wish to set a delay:
1. Press the Delay pad.
° "DELAY" flashes.
° 00:00 will appear in the display. ...........................
2. Press the More+ or Less- pad to set the
amount of time you want to delay the cycle. ............................................
After four seconds, CLEAN, DELAY and LOCK will appear
in the display to show that the oven is set for a delayed
clean operation. The delay time is displayed.
When the Self-Clean eyeme starts:
° "DELAY" will turn off.
° The dean time will appear in the display.
TO cance! the Semf-Clean cycle:
Press the CANCEL pad.
° All words disappear from the display.
° All functions are canceled.
° The time of day appears in the display.
During the Self-C ean Cycle
When LOCK shows in the display, the door cannot be opened.
To prevent damage to the door, do not force the door open
when LOCK is displayed.
Smoke and Smells
You may see some smoke and smell an odor the first few
times the oven is cleaned. This is normal and will lessen in
time.
Smoke may also occur if the oven is heavily soiled or if a
broiler pan was left in the oven.
Sounds
As the oven heats, you may hear sounds of metal parts
expanding and contracting. This is normal and will not
damage the oven.
After Se f-Cleaning
About one hour after the end of the self-clean cycle, LOCK
will turn off. The door can then be opened. Move door lock
lever to the left to unlock.
Some soil may leave a light gray, powdery ash. Remove
it with a damp cloth. If soil remains after wiping, that means
the clean cycle was not long enough. The soil will be re-
moved during the next clean cycle.
if oven racks were left in the oven and do not slide
smoothly after a clean cycle, wipe racks and rack supports
with a small amount of vegetable oil to make them easier to
move.
Fine lines may appear in the porcelain because it went
through heating and cooling. This is normal and wiii not
affect performance.
A white discoloration may appear after cleaning if acidic
or sugary foods were not wiped up before the self=clean
cycle= This discoloration is normal and will not affect perfor-
mance.
If the oven door is left open, "DOOR" will flash in the
display and a signal will beep until the door is closed
and the Clean pad is pressed again.
If more than five seconds elapse between pressing the
Clean pad and the More+ or Less- pad, the program will
automatically return to the previous display.
The oven door will be damaged if the oven door is
forced to open when "LOCK" is still displayed.
17
Cleaning Procedures
,!fa part !s removed, be sure !t is correct!y replaced, }
* Brand names are registered trademarks of the
respective manufacturers.
** To order call 1-877-232-6771 USAand
1-800-688-8408 Canada.
PROCEDURE
Backgaard and
Cooktop -
Porcelain Enamel
Broiler Pan and
insert
Clock and
Control Pad
Area
Control Knobs
Cooktop -
Gmass-Ceramic
PorceHainenameHis gHassfused on metaHand may crack or chip with misuse. It is acid resistant, not acid
proof. AH spiHovers,espedaHy acidic or sugary spillovers, should be wiped up immediately with a dry cloth.
, When cool, wash with soapy water, rinse and dry.
, Never wipe off awarm or hot surface with a damp cloth. This may cause cracking or chipping.
, Never use oven cleaners, abrasive or caustic cleaning agents on exterior finish of range.
Never cover insert with aluminum foil as this prevents the fat from draining to the pan below.
, Place soapy cloth over insert and pan; let soak to loosen soil=
° Wash in warm soapy water. Use scouring pad to remove stubborn soil.
° Broiler pan and insert can be cleaned in dishwasher.
, To activate "Control Lock" for cleaning, see page 9.
, Wipe with a damp cloth and dry. Do not use abrasive cleaning agents as they may scratch the surface.
, Glass cleaners may be used if sprayed on a cloth first. 00 NOTspray directly on eontrolpad and
display area.
° Remove knobs in the OFFposition by pulling forward.
° Wash, rinse and dry=Do not use abrasive cleaning agents as they may scratch the finish.
° Turn on each element to be sure the knobs have been correctly replaced.
Never use even cleaners, chlorine bleach, ammonia or glass cleaners with ammonia. NOTE: Call
an authorized servicer if the glass=ceramic top should crack, break or if metal or aluminum foil
should melt on the cooktop.
° Allow the eooktop to cool before cleaning=
° General - Cleancooktop after each use,or when needed, with a damp paper towel and Cooktop Cleaning
Creme* (Part No=20000001_)**=Then, buff with a clean dry cloth.
NO TE:Permanent stainswill develop ff soilis ah'owedto cook on byrepeatedly usingthe eooktop _4#ensoiled.
° Heavy Soils or Metal Marks - Dampen a "scratchless" or "never scratch" scrubber sponge. Apply
Cooktop Cleaning Creme* (Part No=20000001_)**and scrub to remove as much soil as possible. Apply a
thin layer of the creme over the soil, cover with a damp paper towel and let stand 30 to 45 minutes (2-3
hours for very heavy soil)=Keep moist by covering the paper towel with plastic wrap. Scrub again, then
buff with a clean dry cloth.
NOTE: Only usea CLEAN,DAMP Uscratchless"pad that issafe for non-stick eookware. Thepattern and glass
will be damaged ff the pad is not damp, ff the pad is soiled, or ff another type of pad is used.
° Bamed-on or Crusty Soils - Scrub with a "scratchless" or "never scratch" scouring pad and Cooktop
Cleaning Creme*.
18
Oven Window
and Door - Glass
, Avoid using excessive amounts of water which may seep under or behind gHasscausing staining.
° Wash with soap and water. Rinsewith dear water and dry. GHasscHeanercan be used ifsprayed on a cHoth
first.
° Do not use abrasive materiaHssuch asscouring pads, steeHwooHor powdered cHeanersasthey wiHHscratch
gHass.
Oven interior , FoHHowinstructions on pages 16-17 to set a seHf-cHeancycHe.
Oven Racks
Stainmess Steel
(seHectmodeHs)
Brushed Chrome
(seHectmodeHs)
Door Handle,
Side Panems -
Painted Enamem
° CHeanwith soapy water.
° Remove stubborn soiHwith cHeansingpowder or soap-fiHHedscouring pad. Rinseand dry.
° RackswiHHpermanentHydiscoHorand maynotsHidesmoothHyifHeftintheoven during aseHf-cHeanoperation.
If this occurs, wipe the rack edge and rack support with a smaHHamount of vegetabHeoiHto restore ease
of movement, then wipe off excess oil
° DO NOT USE ANY CLEANING PRODUCT CONTAINING CHLORINE BLEACH.
° DO NOTUSEABRASIVE Oft ORANGE CLEANERS.
° ALWAYS WIPE WITH THE GRAIN WHEN CLEANING.
° Daily Cleaning/Light Soil -- Wipe with one of the foHHowing- soapy water,white vinegar/water soHution,
FormuHa409GHassand Surface CHeaner*or a simiHargHasscHeaner- using a sponge or soft cHoth.Rinse
and dry. To poHishand heHpprevent fingerprints, foHHowwith StainHessSteeHMagic Spray (Part No.
20000008)**.
° JVioderate/Heavy Soil -- Wipe with one of the foHHowing- Ben Ami, Smart CHeanser,or Soft Scrub* -
using a damp sponge or soft cHoth.Rinse and dry. Stubborn soiHsmay be removed with a damp muHti-
purpose Scotch-Brite* pad; rubevenHywith the grain. Rinseand dry'.To restore Husterand remove streaks,
foHHowwith StainHessSteeHMagic Spray*.
° Discoloration -- Using a damp sponge or soft cHoth,wipe with Cameo StainHessSteeHCHeaner*=Rinse
immediateHyand dry=To remove streaks and restore Huster,foHHowwith StainHessSteeHMagic Spray*.
, When cool wash with soapy water, rinse and buff the surface.
, For heavier soil use a miHdabrasive cHeanersuch as baking soda or Ben Ami*, rubbing with the grain to
avoid streaking the surface. Rinse and buff.
, To prevent scratching, do not use abrasive cHeaners=
, To restore Husterand remove streaks, foHHowwith StainHessSteeHMagic Spray* (Part #20000008)_*=
Chrome will perma#endy discolor if soil is allowed to bake ono
, When cool wash with warm soapy water, rinse and dry'.Never wipe a warm or hot surface with a damp
cHothas this may damage the surface and may cause a steam burn.
, Forstubborn soil use mildly abrasivecHeaningagents such asbaking soda paste or Ben Ami.* Do not use
abrasive, caustic or harsh cHeaningagents such as steeHwooHpads or oven cHeaners.These products wiHH
scratch or permanentHydamage the surface.
NOTE: Use a dry towel or cloth to wipe up spills, especially acidic or sugary spills° Surface may
discolor or dull if soil is not immediately removed. This is especially important for white surfaceso
* Brand names for cHeaning products are registered trademarks of the respective manufacturers.
** To order direct, caHH1-877-232-6771 USA and 1-800-688-8408 Canada.
19
Oven Door
Do not place excessive weight on er stand on an open oven
Leveling Legs
door.This could cause the range to tip over, break the door,
injure the user,
Do [lot attempt to open or Close door or operate oven unti
/ door iSpropedy replaced,
g Nevei place fingers between hinge and front oven frame,
Hinge arms are Spring mounted. If accidentally hit, the hinge
win Slam Shut against oven frame and Could injure Your
fingers.
Note: The oven door on a new range may feel "spongy"
when it is closed. This is normal and win decrease with use.
To remove:
1. When cool, open the oven door to the first stop position
(opened about four inches}.
2. Grasp door at each side. Do not use the
door handle to lift door.
3. Lift up evenly until door clears hinge
arms.
To replace:
1. Grasp door at each side.
2. Align slots in the door with the hinge arms on the range.
3. Slide the door down onto the hinge arms until the door is
completely seated on the hinges. Push down on the top
corners of the door to completely seat door on hinges. Door
should not appear crooked.
Oven Window
To protect the oven door window:
1. Do not use abrasive cleaning agents such as steel wool
scouring pads or powdered cleansers as they may scratch
the glass.
2. Do not hit the glass with pots, pans, furniture, toys, or other
objects.
3. Do not close the oven door until the oven racks are in place.
Scratching, hitting, jarring or stressing the glass mayweaken
its structure causing an increased risk of breakage at a later
date.
Be sure the anti-tip bracket secures one of the
rear leveling legs to the floor. This bracket pro- /_
vents the range from accidentally tipping
The range should be leveled when nstalled.
If the range is not level turn the plastic _ .A_
leveling legs. ocated at each corner of
the range, until range is level aNti-rip
BRACKET
LEVELING LEG
Oven Light
Be sure bulb is cool before touching bulb.
the bulb to break.
To Replace Oven Light Bulb:
1. When oven is cool, hold bulb cover in place, then slide wire
retainer off cover=NOTE:Bulb cover will fall if not heldin place
while removing wire retainer.
BULB COVER
2. Removebulb eoverand light bulb=
3. Replacewith a 40-wattappli-
ance bulb.
4. Replace bulb cover and se-
cure with wire retainer.
5. Reconnect power to range. Reset clock.
RETAINER
Convenience Outlet
(Canadian models only)
The convenience outlet is located on the
lower left side of the backguard. Be sure
appliance cords do not rest on or near the
surface elemenL If the surface element is
turned on, the cord and outlet win be
damaged.
The convenience outlet circuit breaker
may trip if the small appliance plugged
into it exceeds 10 amps. To reset the
circuit breaker, press the switch located
on the lower edge of the backguard.
Y
CIRCUIT BREAKER
2O
Storage Drawer
matedds in tMs drawer. The drawer may become too warm
for these items when the oven is in use.
The storage drawer can be removed to allow you to dean
To remove:
1. Empty'drawer and pull out to the first stop position.
2. Lift up the front of the drawer.
3. Pull out to the second stop position.
4. Grasp sides and Hiltdrawer up and out.
To replace:
1. Fit the ends of the drawer gHidesinto the raiHsin the range.
2. Lift up the front of the drawer and gentHypush in to the
first stop position.
3. Lift drawer up again and push untiHdrawer is chose&
PP,OBLEM SOLUTmON
° Check if oven controls have been properly seL
try these first. " Check to be sure plug is securely inserted into receptacle.
, Check or re-set circuit breaker. Check or replace fuse.
, Check power supply.
Part or all of appliance
does not work.
but oven does not heat.
Baking results are not as
expected or differ from
previous oven.
Food is not broiling
properly or smokes
excessively.
Check
Check
Check
Check
Check
if surface and/or oven controls have been properly set. See pages 5-15.
if oven door is unlocked after self-clean cycle. See page 17.
if oven is set for a delayed cook or clean program. See pages 11& 16.
if Control Lock is activated. See page 9.
if control is in Sabbath Mode. See page 13.
, Oven may be set for a Cook & Hold or Delay function.
, The Control Lock may have been set. See page 9.
, Make sure the oven vent has not been blocked. See page 15 for location.
, Check to make sure range is level.
, Temperatures often vary, between a new oven and an old one. As ovens age, the oven
temperature often "drifts" and may become hotter or cooler. See page 13for nstmctions on
adjusting the oven temperature. NOTE; It is not recommended to adjust the temperature if
only one or two recipes are in question.
, See "Cooking Made Simple" booklet for more information on bakeware andbaking.
, Check oven rack positions. Food may be too close to element.
, Broil element was not preheated.
, Aluminum foil was incorrectly used. Never line the broiler insert with foil.
, Ovendoor was closed during broiling. Leave the door open to the first stop position (about
4 inches:).
° Trim excess fat from meat before broiling.
° A soiled broiler pan was used.
° Voltage in house may be low.
21
cont.
i
PROBLEM
Oven will not self-clean.
Oven did not
clean properly.
Oven door will not unlock
after self=clean cycle.
Smoothtop surface
shows wear.
Moisture collects on oven
window or steam comes
from oven vent.
There is a strong odor
or light smoke when
oven is turned on.
Fault Codes
Noises may be heard.
There are no beeps and
"SAb" flashing and then
displayed continuously.
, Check to make sure the cycle is not set for a ddayed start. See page 16.
° Check if door is chased.
, Check if control is in Sabbath Mode. See page 13.
, Oven maybe over 400° R Oven temperature must be below 400° Fto program a clean cycle.
, Longer cleaning time may be needed.
, Excessivespillovers, especially sugary and/or acidic foods, were not removed prior to the
self-clean cycle.
, Oven interior is still hot. Allow about one hour for the oven to cool after the
completion of a self-clean cycle. The door can be opened when the LOCK indicator word is
not displayed.
, The control and door may be locked. See pages 9 and 17 to unlock.
1.Tiny scratches or abrasions.
, Make sure cooktop and pan bottom are clean. Do not slide glass or metal pans across top.
Make sure pan bottom is not rough. Use the recommended cleaning agents. See page 18.
2.Metal marks.
, Do not slide metal pans across top. When cool. clean with Cooktop Cleaning Creme.
See page 18.
3. Brown streaks and specks.
, Remove spills promptly. Neverwipe with a soiled cloth orsponge. Make sure cooktop and pan
bottom are clean.
4.Areas with a metallic sheen.
, Mineral deposits from water and food. Use recommended cleaning agents. See page 18.
5. Pitting or flaking.
, Remove sugary, boilovers promptly. See page 18.
, This is normal when cooking foods high in moisture.
, Excessive moisture was used when cleaning the window.
, This is normal for a new range and will disappear after a few uses. Initiating a dean cycle
will "burn off" the odors more quickly.
, Turning on a ventilation fan will help remove the smoke and/or odor.
, Excessivefood soils on the oven bottom. Use a self-clean cycle.
° BAKE or LOCK may flash rapid[y in the disp[ay to a[ert you if there is an error or a prob[em.
If BAKE or LOCK appear in the display, press CANCEL pad. If BAKE or LOCK continue to
flash, disconnect power to the appliance. Wait a few minutes, and then reconnect power.
Ifthe flashing still continues, disconnect power to the appliance and callan authorized servicer.
° Ifthe oven is heavily soiled, excessivefiareups may result in a fault code during cleaning. Press
the CANCEL pad and allow the oven to cool completely, wipe out excess soil, then reset the
clean cycle. If the fault code reappears, contact an authorized servicer.
° The oven makes several low level noises. You may hear the oven relays as they go onand off.
This is normal.
° As the oven heats and cools, you mayhear sounds of metal parts expanding and contracting.
This is normal and will not damage your appliance.
Oven may be in Sabbath Mode. See page 13.
Oven is in Sabbath Mode. To cancel, press and hold the Clock pad for five
seconds.
22
Loading...