Jenn-Air JXT8036ADS User Manual [en, es, fr]

0 (0)

R A N G E H O O D

Model Number:	JXT8030ADS	JXT8036ADS	JXT8042ADS
Manufacturer Number:	S99E30S	S99E36S	S99E42S
Size:	30”	36”	42”

USER

G U I D E

TABLE OF CONTENTS
Safety Instructions....................................................	1
Controls & Features...............................................	2-4
Maintenance.........................................................	5-6
Warranty..................................................................	7

CONTROLS & FEATURES	2

TOUCH CONTROLS & FEATURES

The standard Metal Filters are required to be cleaned frequently and as recommended in order to maintain blower efficiency. If improperly maintained, residue from cooking will sift though filters and cause damage to hood blowers and other sensitive components; and possibly clog duct work and create a fire hazard.

CONTROLS & FEATURES	3

CONTROLS: FILTER CHANGE INDICATOR (CARBON FILTERS)

Filter Change Reminder (Carbon, if fitted):

When your hood is installed as a 'Purifying' (Ductless Recirculating) unit, it is fitted with a set of Carbon Filters to purify exhaust and fumes from cooking, then re-circulate the air within the home. These Carbon Filters are required to be replaced after every 120 hours of use. The Filter Change Reminder function in the microprocessor needs to be switched on. The microprocessor in the controls when set, will elapse and count usage time and indicate by a flashing when carbon filter replacement is needed.

Setting the Filter Change Reminder:

When Off, hold for approx. 5 seconds. The display will change from

(exhaust mode) to , (purifying mode/ carbon filters used) this indicates that the elapse timer function is switched on and Carbon Filters are used.

Filter Replace Indicator:

When the display starts flashing, the Carbon Filters require replacement.

Re-setting Function:

Once filters are replaced, with hood off, press and hold , the display will appear; hold for approximately 5 seconds until on display disappears . The Filter Change Reminder is now re-set and a new 120 hours elapse cycle is initiated.

Set Mode

hold 5 secs. display from <--> to <C>

Change Filters

display <C> flashes

To Reset
hold 5 secs.	display from <C> to < >

CONTROLS & FEATURES	4

CONTROLS: FILTER CLEAN INDICATOR (METAL FILTERS)

Filter Clean Reminder (Standard Metal Filters fitted)

Whether your hood is installed as an Exhaust or Purifying unit, a set of metal filters are fitted by the factory. These Metal Filters are intended to filter out residue from cooking.

They need not be replaced on a regular basis but are required to be kept clean. The Filter Change Reminder function in the microprocessor will automatically indicate by a flashing

when the metal filters need to be cleaned after every 30 hrs. of use.

Filters can be cleaned by hand with non-abrasive soap or in a dishwasher. Heavily soiled

filters should also be soaked in grease cutting detergent such as Formula '409' or its equivalent, prior to cleaning.

Filter Clean Reminder:

When flashes on display, the metal filters installed are required to be cleaned. This will occur after every 30 hours of use.

Re-setting Function:

Reset the Filter Clean Reminder timer when filters are cleaned and re-installed. Press and hold for approx. 5 seconds, the display will appear; hold for approximately 5 seconds until on display disappears . The Filter Clean Reminder function

is now re-set and a new 30 hours elapse cycle is initiated.

Clean Filters

display <A> flashes

To Reset
hold 5 secs.	display from <C> to < >

MAINTENANCE	5

CLEANING

Surface Maintenance:

Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent (e.g. Comet powder scrub, EZ-Off oven cleaner), or steel wool/scouring pads which will scratch and damage surface.

For heavier soil use liquid degreaser such as “Formula 409” or “Fantastic” brand cleaner.

After cleaning, you may use non-abrasive stainless steel polish/ cleaners such as 3M or ZEP, to polish and buff out the stainless luster and grain. Always scrub lightly, with clean cotton cloth, and with the grain. Do not use any product containing chlorine bleach. Do not use “orange” cleaners.

Metal Filters

The Metal Filters fitted by the factory are intended to filter out residue and grease

from cooking. They need not be replaced on a regular basis but are required to be kept clean. Filters should be cleaned after every 30

hours of use. Use the Filter Clean Reminder function on the controls to determine when filters require cleaning.

Remove and clean by hand or in dishwasher. Spray 'Formula 409' or equivalent degreasing detergent and leave to soak if heavily soiled.

Dry filters and re-install before using hood.

Replacing Metal Filters

Should filters wear out due to age and prolonged use, replace with following part number:

Hood Model:	Part No.	Filters in pkg.

JXT8030ADS	49001002	2
JXT8036ADS	49001001	3
JXT8042ADS	49001001	3

Metal Filter Dimensions:

16.14 in x 9.17 in x 0.35 in

410 mm x 233 mm

Also replace any damaged filter that has punctured or broken mesh, bent or broken frame.

MAINTENANCE	6

LIGHTS

Replacing Light Bulbs

CAUTION: Light bulb becomes extremely hot when turned on.

DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns.

Make sure all power is turned off and bulbs are cool.

Remove by turning bulb counter clockwise.

If bulbs are difficult to turn due to prolonged use, firmly attach a glass suction cup approx. the diameter of the bulb and turn. Use a rubber gripper or rubber gloves to remove bulb.

Replacement bulbs are available at specialty lighting stores. Purchase type GU10 120V 50W halogen bulbs.

Or to order bulbs, please call our service center: 1-800-JENNAIR (1-800-536-6247)

WARRANTY	6

Jenn-Air Ancillary Warranty

Full One Year Warranty - Parts and Labor

One (1) year - From the date of original retail purchase, any part that fails in normal home use will be repaired or replaced free of charge.

Canadian Residents

This warranty covers only those appliances installed in Canada that have been listed with Canadian Standards Association unless the appliances are brought into Canada due to transfer of residence from the United States to Canada.

The specific warranties expressed above are the ONLY warranties provided by the manufacturer. These warranties give you specific legal rights, and you may also have other rights which vary from state to state.

CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. MAYTAG CORPORATION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY STATE TO STATE OR PROVINCE TO PROVINCE.

What is Not Covered By These Warranties:

1.Conditions and damages resulting from any of the following:

a.Improper installation, delivery, or maintenance.

b.Any repair, modification, alteration, or adjustment not authorized by the manufacturer or an authorized servicer.

c.Misuse, abuse, accidents, unreasonable use, or acts of God.

d.Incorrect electric current, voltage, or supply.

e.Improper setting of any control.

2.Warranties are void if the original serial numbers have been removed, altered or cannot be readily determined.

3.Light bulbs.

4.Products purchased for commercial or industrial use.

5.The cost of service or service call to:

a.Correct installation errors.

b.Instruct the user on the proper use of the product.

c.Transport the appliance to the servicer and back.

6.Consequential or incidental damages sustained by any person as a result of any breach of these warranties. Some states do not allow the exclusion or limitation of consequential or incidental damages, so the above exclusion may not apply.

If You Need Service

First see the Troubleshooting section in your Use and Care Guide or call the dealer from whom your appliance was purchased or call Maytag Services, LLC, Jenn-Air Customer Assistance at 1-800-JENNAIR (1-800-536-6247) U.S.A. and Canada to locate an authorized servicer.

Be sure to retain proof of purchase to verify warranty status. Refer to WARRANTY for further information on owner’s responsibilities for warranty service. If the dealer or service company cannot resolve the problem, write to Maytag Services,

LLC, Attn: CAIR Center, P.O. Box 2370, Cleveland, TN 37320-2370, or call 1-800-JENNAIR (1-800-536-6247) (USA and Canada). U.S. customers using TTY for deaf, hearing impaired or speech impaired, call 1-800-688-2080.

Notes: When writing or calling about a service problem, please include:

a.Your name, address and telephone number;

b.Model number and serial number;

c.Name and address of your dealer or servicer;

d.A clear description of the problem you are having;

e.Proof of purchase (sales receipt).

User’s guides, service manuals and parts information are available from Maytag Services, LLC, Customer Assistance.

+ 18 hidden pages