Jenn-Air WW2750B, WW2750W, WW2780B, WW2780W Dimension Guide

www.dexpress.com DIMENSION EXPRESS Fax on Demand [phone]

	This Data Sheet Includes Information On
	Jenn-Air
•	Product Model Number (s):	•
	27" Electric Double Ovens:
	WW2750B, WW2750W, WW2780B and WW2780W
•	Dimensions (Actual Size)	•
	Cutout width:	25"
	Cutout height:	50 1/2"
	Minimum cabinet width: 27"
	Minimum cabinet depth: 24"
	Minimum cutout location from floor : 3" to 12"
	Distance from face of cabinet to
	outer edge of open doors (Door Swing):	21 3/8"
	Distance from face of cabinet to
	front of closed door handle:	3 3/4"
	Overall unit width:	26 3/4"
	Overall unit height:	51"
	Penetration into cabinet:	23 1/4"

Oven overlap distances when using cutout dimensions listed above:

Top overlap: 1/2"

Bottom overlap: 0"

Right side overlap: 7/8"

Left side overlap: 7/8"

•

Additional Information

•

•Cutout height and width are ± 1/16".

•Cutout in cabinet should be level and straight. There are no provisions to level the unit after it is installed.

•Construct 5/8" minimum plywood floor flush with bottom of opening. Floor must be level and straight and capable of supporting 250 lbs.

•A three-wire, single phase, A.C. 120/208-240 volt, 60Hz cycle electrical system must be provided (Load 44.8 amps @ 120/240VAC). 7/8" O.D. flexible cable 4 feet long is furnished by manufacturer. Mount junction box in area under plywood floor if adequate lower cabinet space is available. Locate 1 1/4" conduit access hole in the back right hand side of the plywood floor.

•For European style cabinets (flush front) the required clearance for operation of the oven door is a minimum spacing of 7/8" between the cutout and the door, hinge or drawer of the cabinet.

•Some 27" built-in cabinets may not be wide enough, due to their construction, to allow this installation.

•WW275OB and WW278OB : Black.

•WW275OW and WW278OW : White.

Subject to change without notice. This system is designed to
be updated daily if necessary. Dimension Express is not
responsible for use of superseded, voided, or outdated data
sheets. Because of the difficulty or impracticability of deter-
mining actual damages, liability of Dimension Express shall
not exceed $50.00.
Copyright © Dimension Express, 2000.	262

Cabinet Opening		27"
(not to scale)		25"
			24"
CAUTION: If cabinet doors are
provided above wall oven, a
minimum spacing between the top
of the cutout	and the door above
is 2" for 1/2" or less thick doors.
2 1/2" for 1/2" to 3/4" thick doors.
3 1/2" for 3/4" and up thick doors.
		12"
	Alt. electrical location	18"
		50 1/2"
7/8" is required spacing
from the cutout to the
doors, hinges, or drawer
fronts to each side and
below.		3" to 12"
		Provide for 120/208-240	volt electrical
		connection in this area.

Overall Dimensions

(not to scale)

51"

23 1/4"

26 3/4"

3 3/4"

• NEVER reuse Data Sheets. Data Sheets are subject to change without	• Call Dimension Express if you have any questions at [phone] •
notice. Dimension Express is a FREE service bureau and is updated daily,	• Always refer to a current Code at a Glance or manufacturer directory •
it makes far more sense to spend the time necessary to request new Data	• Data Sheet codes change on the first of odd numbered months at 12:01am •
Sheets for each project, as opposed to the problems, time, costs, and risks	BN207 • A262 • 31469 • 002906 • 112422 • 13061
associated with reusing old Data Sheets.