HP HLMP-6204, HLMP-6205, HLMP-6206, HLMP-6208, HLMP-6300 Datasheet

H

Subminiature LED Lamps

Technical Data

Features

•Subminiature Flat Top Package

Ideal for Backlighting and Light Piping Applications

•Subminiature Dome Package

Diffused Dome for Wide Viewing Angle Nondiffused Dome for High Brightness

HLMP-PXXX Series

HLMP-QXXX Series

HLMP-6XXX Series

HLMP-70XX Series

Dome Packages

The HLMP-6XXX Series dome lamps for use as indicators use a tinted, diffused lens to provide a wide viewing angle with a high on-off contrast ratio. High brightness lamps use an untinted, nondiffused lens to provide a high luminous intensity within a narrow radiation pattern.

•Arrays

•TTL and LSTTL Compatible 5 Volt Resistor Lamps

•Available in Six Colors

•Ideal for Space Limited Applications

•Axial Leads

•Available with Lead Configurations for Surface Mount and Through Hole PC Board Mounting

Description

Flat Top Package

The HLMP-PXXX Series flat top lamps use an untinted, nondiffused, truncated lens to provide a wide radiation pattern that is necessary for use in backlighting applications. The flat top lamps are also ideal for use as emitters in light pipe applications.

Arrays

The HLMP-66XX Series subminiature lamp arrays are available in lengths of 3 to 8 elements per array. The luminous intensity is matched within an array to assure a 2.1 to 1.0 ratio.

Resistor Lamps

The HLMP-6XXX Series 5 volt subminiature lamps with built in current limiting resistors are for use in applications where space is at a premium.

Lead Configurations

All of these devices are made by encapsulating LED chips on axial lead frames to form molded epoxy subminiature lamp packages. A variety of package configuration options is available. These include special

surface mount lead configurations, gull wing, yoke lead or Z- bend. Right angle lead bends at 2.54 mm (0.100 inch) and

5.08 mm (0.200 inch) center spacing are available for through hole mounting. For more information refer to Standard SMT and Through Hole Lead Bend Options for Subminiature LED Lamps data sheet.

1-174

5964-9350E

Device Selection Guide

Part Number: HLMP-XXXX

	DH AS	High			High				Device
Standard	AlGaAs	Efficiency			Perf.	Emerald			Outline
Red	Red	Red	Orange	Yellow	Green	Green	Device Description[1]		Drawing
	P105	P205	P405	P305	P505	P605	Untinted, Nondiffused,		A
							Flat Top
	P102	P202	P402	P302	P502		Untinted, Diffused,		B
							Flat Top
6000/6001	Q101	6300	Q400	6400	6500	Q600	Tinted, Diffused
	Q105	6305		6405	6505		Untinted, Nondiffused,
							High Brightness
	Q150	7000		7019	7040		Tinted, Diffused, Low		B
							Current
	Q155						Nondiffused, Low
							Current
		6600		6700	6800		Tinted, Diffused,
							Resistor, 5 V, 10 mA
		6620		6720	6820		Diffused, Resistor, 5 V,
							4 mA
6203		6653		6753	6853		3 Element	Matched
6204		6654		6754	6854		4 Element	Array,
								Tinted,
6205		6655		6755	6855		5 Element	Diffused	C
6206		6656		6756	6856		6 Element
6208		6658		6758	6858		8 Element

Package Dimensions

(A) Flat Top Lamps

NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES).	*Refer to Figure 1 for design concerns.
2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD.

1-175

Package Dimensions (cont.)

(B) Diffused and Nondiffused

NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES).	*Refer to Figure 1 for design concerns.
2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD.

(C) Arrays

NOTES:

1.ALL DIMENSIONS ARE IN MILLIMETERS (INCHES).

2.PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD.

Figure 1. Proper Right Angle Mounting to a PC Board to Prevent Protruding Cathode Tab from Shorting to Anode Connection.

1-176

Absolute Maximum Ratings at TA = 25°C

		DH AS	High				High
	Standard	AlGaAs	Eff.				Perf.	Emerald
Parameter	Red	Red	Red	Orange		Yellow	Green	Green	Units
DC Forward Current[1]	50	30	30	30		20	30	30	mA
Peak Forward Current[2]	1000	300	90	90		60	90	90	mA
DC Forward Voltage			6			6	6	6	V
(Resistor Lamps Only)
Reverse Voltage (IR = 100 μA)	5	5	5	5		5	5	5	V
Transient Forward Current[3]	2000	500	500	500		500	500	500	mA
(10 μs Pulse)
Operating Temperature Range:	-55 to	-40 to		-55 to +100			-40 to	-20 to
Non-Resistor Lamps	+100	+100					+100	+100	°C
Resistor Lamps				-40 to +85			-20 to
							+85
Storage Temperature Range				-55 to +100					°C
For Thru Hole Devices			260°C for 5 Seconds
Wave Soldering Temperature
[1.6 mm (0.063 in.) from body]
For Surface Mount Devices:			235°C for 90 Seconds
Convective IR
Vapor Phase			215°C for 3 Minutes

Notes:

1.See Figure 5 for current derating vs. ambient temperature. Derating is not applicable to resistor lamps.

2.Refer to Figure 6 showing Max. Tolerable Peak Current vs. Pulse Duration to establish pulsed operating conditions.

3.The transient peak current is the maximum non-recurring peak current the device can withstand without failure. Do not operate these lamps at this high current.

1-177

Electrical/Optical Characteristics, TA = 25°C

Standard Red

Device
HLMP-	Parameter	Symbol		Min.	Typ.	Max.	Units	Test Conditions
6000				0.5	1.2
6001	Luminous Intensity[1]	I	v	1.3	3.2		mcd	I = 10 mA
								F
6203 to				0.5	1.2
6208
	Forward Voltage	VF		1.4	1.6	2.0	V	IF = 10 mA
All	Reverse Breakdown	VR		5.0	12.0		V	IR = 100 μA
	Voltage
P005	Included Angle Between	2θ1/2			125
	Half Intensity Points[2]						Deg.
All					90
Others
	Peak Wavelength	λPEAK			655		nm
	Dominant Wavelength[3]	λd			640		nm
	Spectral Line Half Width	Δλ1/2			24		nm
All	Speed of Response	τs			15		ns
	Capacitance	C			100		pF	VF = 0; f = 1 MHz
	Thermal Resistance	RθJ-PIN			170		°C/W	Junction-to-Cathode
								Lead
	Luminous Efficacy[4]	η			65		lm/W
			v

1-178