7OFTR 850 (OW) RU/HA
English
Operating Instructions
OVEN
Contents
Operating Instructions,1
Warnings,2
Assistance,3
Description of the appliance,4
Description of the appliance,5
Installation,6
Start-up and use,8
Analogue Programmer,8
Modes,9
Precautions and tips,12
Maintenance and care,13
Русскии
Руководство по эксплуатации
ДУХОВОЙ ШКАФ
Содержание
Руководство по эксплуатации,1
Предупреждения,2
Сервисное обслуживание,3
Описание изделия,4
Описание изделия,5
Установка,14
Включение и эксплуатация,16
Аналоговый программер,16
Программы,17
Предосторожности и рекомендации,20
Техническое обслуживание и уход,21
OT 857 CO RFH
OT 857 CA RFH
OT 857 A RFH
OT 857 O RFH
7OFTR 850 RU/HA
Warnings
WARNING: The appliance and its accessible parts
become hot during use. Care should be taken to
avoid touching heating elements. Children less than 8
years of age shall be kept away unless continuously
supervised. This appliance can be used by children
aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been
given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made
by children without supervision.
Do not use harsh abrasive cleaners or sharp metal
scrapers to clean the oven door glass since they can
scratch the surface, which may result in shattering of
the glass.
Never use steam cleaners or pressure cleaners on
the appliance.
WARNING: Ensure that the appliance is switched
off before replacing the lamp to avoid the possibility
of electric shock.
! When you place the rack inside, make sure that the
stop is directed upwards and in the back of the cavity.
Предупреждения
ВНИМАНИЕ: Данное изделие и его доступные
комплектующие сильно нагреваются в процессе
эксплуатации.
Будьте осторожны и не касайтесь нагревательных
элементов.
Не разрешайте детям младше 8 лет приближаться
к изделию без контроля.
Данное изделие может быть использовано
детьми старше 8 лет и лицами с ограниченными
физическими, сенсорными или умственными
способностями или без опыта и знания о
правилах использования изделия при
условии надлежащего контроля или обучения
безопасному использованию изделия с учетом
соответствующих рисков. Не разрешайте
детям играть с изделием. Не разрешайте детям
осуществлять чистку и уход за изделием без
контроля взрослых.
Не используйте абразивные вещества или
режущие металлические скребки для чистки
стеклянной дверцы духового шкафа, так как
они могут поцарапать поверхность, что может
привести к разбиванию стекла.
Никогда не используйте паровые чистящие
агрегаты или агрегаты под высоким давлением
для чистки изделия.
ВНИМАНИЕ: Проверьте, чтобы изделие было
выключено, перед заменой лампочки во
избежание возможных ударов током.
! При установке решетки проверить, чтобы
фиксатор был повернут вверх с задней стороны
выемки.
2
Assistance
! Never use the services of an unauthorised technician.
Please have the following information to hand:
• The type of problem encountered.
• The appliance model (Mod.).
• The serial number (S/N).
The latter two pieces of information can be found on the data plate located
on the appliance.
Сервисное обслуживание
! Никогда не обращайтесь к неуполномоченным техникам.
При обращении в Центр Технического Обслуживания необходимо
сообщить:
• Тип неисправности;
• Модель изделия (Мод.)
• Номер тех. паспорта (серийный №)
Эти данные вы найдете на паспортной табличке, расположенной на
изделии.
3
Description of the appliance
Overall view
1. POSITION 1
2. POSITION 2
3. POSITION 3
4. POSITION 4
5. POSITION 5
6. GUIDES for the sliding racks
7. DRIPPING PAN
8. GRILL
9. Control panel
Описание изделия
Общии вид
1. ПОЛОЖЕНИЕ 1
2. ПОЛОЖЕНИЕ 2
3. ПОЛОЖЕНИЕ 3
4. ПОЛОЖЕНИЕ 4
5. ПОЛОЖЕНИЕ 5
6. ВЫДВИЖНЫЕ НАПРАВЛЯЮЩИЕ уровней
7. ПРОТИВЕНЬ
8. РЕШЕТКА
9. Панель управления
7
8
9 6
1
2
3
4
5
4
1
2
4 3
Description of the appliance
Control panel
1. SELECTOR Knob
2. ANALOGUE PROGRAMMER knob
3. THERMOSTAT Knob
4. Indicator light THERMOSTAT
Описание изделия
Панель управления
1. Рукоятка ПЕРЕКЛЮЧАТЕЛЯ
2. Рукоятка АНАЛОГОВОГО ПРОГРАММЕРА
3. Рукоятка ТЕРМОРЕГУЛЯТОРА
4. Индикатор ТЕРМОРЕГУЛЯТОРА
5
Installation
! Please keep this instruction booklet in a safe place for future reference. If
the appliance is sold, given away or moved, please make sure the booklet is
also passed on to the new owners so that they may benet from the advice
contained within it.
! Please read this instruction manual carefully: it contains important information
concerning the safe operation, installation and maintenance of the appliance.
Positioning
! Do not let children play with the packaging material; it should be disposed
of in accordance with local separated waste collection standards (see
Precautions and tips).
! The appliance must be installed by a qualied professional in accordance
with the instructions provided. Incorrect installation may damage property or
cause harm to people or animals.
Built-in appliances
Use an appropriate cabinet to ensure that the appliance operates properly:
• The panels adjacent to the oven must be made of heat-resistant material.
• Cabinets with a veneer exterior must be assembled with glues which can
withstand temperatures of up to 100°C.
• To install the oven under the counter (see diagram) or in a kitchen unit,
the cabinet must have the following dimensions:
595 mm.
595 mm.
25 mm.
545 mm.
5 mm.
567 mm.
23 mm.
575-585 mm.
45 mm.
560 mm.
547 mm. min.
! The appliance must not come into contact with electrical parts once it has
been installed.The indications for consumption given on the data plate have
been calculated for this type of installation.
Ventilation
To ensure adequate ventilation, the back panel of the cabinet must be
removed. It is advisable to install the oven so that it rests on two strips of
wood, or on a completely at surface with an opening of at least 45 x 560
mm (see diagrams).
560 mm.
45 mm.
Centring and xing*
1. Position brackets “A” against oven support “B”.
2. Position tabs “C” against brackets “A”. If the thickness of the cabinet side
panel:
• is 16 mm thick: place the tab so that the number 16 written on it is
facing you;
• is 18 mm thick: place the tab so that the part without any text is facing
you;
• is 20 mm thick: do not t the tab.
3. Fix the brackets and tabs onto the edge of the cabinet side panel using
screws “D”.
4. Fix the oven to the cabinet using the screws and plastic washers “E”.
D
A
B
D
D
16
16
C
C
E
E
Electrical connection
Ovens equipped with a three-pole power supply cable are designed to operate
with alternating current at the voltage and frequency indicated on the data
plate located on the appliance (see below).
Fitting the power supply cable
1. Open the terminal board by inserting
a screwdriver into the side tabs of the
cover. Use the screwdriver as a lever by
pushing it down to open the cover (see
diagram).
2. Install the power supply cable by
loosening the cable clamp screw
and the three wire contact screws
L-N- .
Connect the wires to the corresponding
terminals: the Blue wire to the terminal
marked (N), the Brown wire to the
terminal marked (L) and the Yellow/
Green wire to the terminal marked
(see diagram).
3. Secure the cable by fastening the
clamp screw.
4. Close the cover of the terminal board.
Connecting the supply cable to the mains
Install a standardised plug corresponding to the load indicated on the data
plate (see side).
The appliance must be directly connected to the mains using an omnipolar
circuit-breaker with a minimum contact opening of 3 mm installed between the
appliance and the mains, suitable for the load indicated and complying with
current electrical regulations (the earthing wire must not be interrupted by the
circuit-breaker). The supply cable must not come into contact with surfaces
with temperatures higher than 50°C.
! The installer must ensure that the correct electrical connection has been
made and that it is compliant with safety regulations.
Before connecting to the power supply, make sure that:
L
N
N
L
6
GB
• The appliance is earthed and the plug is compliant with the law.
• The socket can withstand the maximum power of the appliance, which is
indicated on the data plate (see below).
• The voltage must be in the range between the values indicated on the
data plate (see below).
• The socket is compatible with the plug of the appliance. If the socket is
incompatible with the plug, ask an authorised technician to replace it. Do
not use extension cords or multiple sockets.
! Once the appliance has been installed, the power supply cable and the
electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by authorised technicians
only (see Assistance).
! The manufacturer declines any liability should these safety measures not
be observed.
APPLIANCE SPECIFICATIONS
Dimensions*
width 43.5 cm
height 32,4 cm
depth 41.5 cm
Volume*
59l
Dimensions**
width 45.5 cm
height 32,4 cm
depth 41.5 cm
Volume**
62 l
Electrical
connections
voltage: 220-240V~ 50/60Hz
or 50 Hz (see data plate)
maximum power absorbed 2800 W
* Only for models with drawn rails.
** Only for models with wire rails.
Energy
Label e
Ecodesign
Energy consumption for Natural
convection – heating mode:
Traditional mode
Declared energy consumption for
Forced convection Class
mode: Baking
This appliance conforms to the
following European Economic
Community directives:
- 2006/95/EC dated 12/12/06 (Low
Voltage) and subsequent amendments.
- 2004/108/EC dated 03/05/89
(Electromagnetic Compatibility) and
subsequent amendments.
- 93/68/EEC dated 22/07/93 and
subsequent amendments.
- 2012/19/EU and subsequent
amendments.
- 1275/2008 standby/off mode.
EU Directive no 65/2014
supplementing Directive 2010/30/EU.
EU Regulation no 66/2014
implementing Directive 2009/125/EC.
Standard EN 60350-1
Standard EN 50564
GB
7
Start-up and use
WARNING! The oven is provided with
a stop system to extract the racks and
prevent them from coming out of the
oven (1). As shown in the drawing, to
extract them completely, simply lift the
racks, holding them on the front part,
and pull (2).
! The rst time you use your appliance, heat the empty oven with its door
closed at its maximum temperature for at least half an hour. Make sure that
the room is well ventilated before switching the oven off and opening the
oven door. The appliance may emit a slightly unpleasant odour caused by
protective substances used during the manufacturing process burning away.
Starting the oven
1. Select the desired cooking mode by turning the SELECTOR knob.
2. Select the desired temperature with the THERMOSTAT knob. See the
Cooking advice table for cooking modes and the suggested cooking
temperatures (see Cooking Modes).
3. When lit, the THERMOSTAT indicator light indicates that the oven is heating
up to the temperature set.
4. You may do the following during cooking:
- change the cooking mode by turning the SELECTOR knob.
- change the temperature by turning the THERMOSTAT knob.
- stop cooking by turning the SELECTOR knob to the “0” position.
! Never put objects directly on the oven bottom to avoid damaging the enamel
coating.
! Always place cookware on the rack(s) provided.
Cooling ventilation
In order to cool down the external temperature of the oven, some models
are tted with a cooling fan that blows out air between the control panel and
the oven door.
! Once the cooking has been completed, the cooling fan remains on until the
oven has cooled down sufciently.
Oven light
It goes on when selecting with the SELECTOR knob. It stays on when a
cooking mode is selected.
Analogue Programmer
TIMER knob
END OF COOKING
icon
TIMER
icon
START OF COOKING
icon
CLOCK
icon
! All settings are only possible if the oven is connected to the electricity mains.
If the power supply fails for longer than 10 seconds, the programmer stops:
when power is restored, the CLOCK icon ashes to indicate that there has
been a powercut and that the time needs to be adjusted again.
If the powercut occurs during a set cooking programme, the programmed
time begins again from the point at which it was stopped (e.g. if a cooking
duration of 1 hour is programmed and a powercut lasting 30 minutes takes
place, the programme will nish after 1 hour and 30 minutes). In this case too,
the CLOCK icon ashes and the time will need to be reset.
MANUAL COOKING
If no programming has been activated, the oven can be operated manually,
using the SELECTOR and THERMOSTAT knobs.
Setting the minute minder
! This function does not interrupt cooking and does not affect the oven; it is
simply used to activate the buzzer when the set amount of time has elapsed.
The minute minder can only be used when no set programming is underway.
To activate the minute minder, briey press the knob 3 times until the MINUTE
MINDER icon begins to ash. The minute minder is set in exactly the same
way as the cooking end time (see corresponding paragraph).
Setting the time
To adjust the time indicated by the pointers, briey press the knob 4 times
until the CLOCK icon begins to ash.
Then, to increase or decrease the displayed time value in steps of 1 minute,
turn the knob clockwise or anticlockwise; the minutes pointer moves clockwise
or anticlockwise accordingly, in steps of 1 minute.
Once 10 seconds have elapsed since the most recent adjustment, the
programmer automatically exits adjustment mode.
Programming cooking
Programming a cooking duration with immediate start
Programming the cooking end time makes it possible to begin cooking
immediately and end automatically in accordance with the programmed time.
To programme the cooking end time, briey press the knob twice until the
END OF COOKING icon begins to ash.
To increase or decrease the cooking time in steps of 1 minute, turn the
knob clockwise or anticlockwise; the minutes pointer moves clockwise or
anticlockwise accordingly, in steps of 1 minute.
The END OF COOKING icon ashes continuously for 10 seconds after the
most recent rotation. The programme can be conrmed by pressing the knob
or letting the 10 seconds elapse, provided that a cooking time of at least 1
minute has been programmed.
The END OF COOKING icon lights up to conrm programming has taken
place successfully.
8
GB
Loading...