Variable speed
MODELMODÈLE DS 9DVF•DS 12DVF MODELO DS 14DVF
CORDLESS DRIVER DRILL PERCEUSE-VISSEUSE À BATTERIE TALADRO ATORNILLADOR A BATERÍA
DS14DVF
SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL
WARNING
IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!
This manual contains important information about product safety. Please read and understand this manual BEFORE operating the power tool. Please keep this manual available for other users and owners before they use the power tool. This manual should be stored in safe place.
INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI
AVERTISSEMENT
Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la mort ou de sérieuses blessures corporelles!
Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit. Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi doit être conservé dans un endroit sûr.
INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES
ADVERTENCIA
¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar en lesiones de gravedad o la muerte!
Este manual contiene información importante sobre la seguridad del producto. Lea y comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual para que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este manual debe ser guardado en un lugar seguro.
|
|
|
|
CONTENTS |
|
|
|
|||||
English |
|
|
|
|
|
Page |
||||||
|
|
|
Page |
ASSEMBLY AND OPERATION |
||||||||
|
|
|
|
|
||||||||
|
|
|
|
|
||||||||
IMPORTANT INFORMATION ............................. |
|
|
3 |
14 |
||||||||
MEANINGS OF SIGNAL WORDS ...................... |
|
|
3 |
APPLICATIONS ................................................... |
14 |
|||||||
SAFETY |
|
|
4 |
REMOVAL AND INSTALLATION METHOD |
|
|||||||
|
|
|
OF BATTERY |
14 |
||||||||
GENERAL SAFETY RULES – FOR ALL |
|
|
|
|||||||||
|
|
CHARGING METHOD |
14 |
|||||||||
BATTERY OPERATED TOOLS |
|
|
4 |
|||||||||
..................... |
|
BEFORE USE |
16 |
|||||||||
SPECIFIC SAFETY RULES AND SYMBOLS |
6 |
|||||||||||
OPERATION |
17 |
|||||||||||
IMPORTANT SAFETY INSTRUCTIONS |
|
|
||||||||||
|
|
THE SCOPE AND SUGGESTIONS |
|
|||||||||
FOR BATTERY CHARGER |
|
|
8 |
|
||||||||
|
|
|
FOR USES |
20 |
||||||||
IMPORTANT SAFETY INSTRUCTIONS |
|
|
|
|||||||||
|
|
HOW TO SELECT TIGHTENING TORQUE |
20 |
|||||||||
FOR USE OF THE BATTERY AND |
|
|
||||||||||
|
|
MAINTENANCE AND INSPECTION |
21 |
|||||||||
BATTERY CHARGER .................................... |
|
|
9 |
|||||||||
DISPOSAL OF THE EXHAUSTED BATTERY ..... |
10 |
ACCESSORIES |
22 |
|||||||||
|
|
|
|
|
|
|
||||||
FUNCTIONAL DESCRIPTION .................................. |
|
|
11 |
STANDARD ACCESSORIES ............................... |
22 |
|||||||
MODEL ................................................................. |
|
|
11 |
OPTIONAL ACCESSORIES ................................. |
23 |
|||||||
NAME OF PARTS ................................................ |
|
|
11 |
PARTS LIST |
67 |
|||||||
SPECIFICATIONS |
|
|
13 |
|||||||||
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|||||||
|
|
|
TABLE DES MATIERES |
|
|
|||||||
Français |
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
Page |
|
|
|
|
Page |
||||
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
||||
INFORMATIONS IMPORTANTES DE SÉCURITÉ |
.. 24 |
ASSEMBLAGE ET FONCTIONNEMENT ................ |
35 |
|||||||||
SIGNIFICATION DES MOTS D’AVERTISSEMENT |
.. 24 |
UTILISATIONS .................................................... |
35 |
|||||||||
SÉCURITÉ |
|
|
25 |
MÉTHODE DE RETRAIT ET D’INSTALLATION |
||||||||
|
|
|
DE LA BATTERIE |
35 |
||||||||
REGLES GENERALE DE SÉCURITÉ – POUR TOUS LES |
|
|||||||||||
MÉTHODE DE RECHARGE |
35 |
|||||||||||
OUTILS FONCTIONNANT SUR BATTERIE |
25 |
|||||||||||
AVANT L’UTILISATION |
37 |
|||||||||||
REGLES DE SÉCURITÉ SPECIFIQUES ET |
|
|
||||||||||
|
|
UTILISATION |
38 |
|||||||||
SYMBOLES |
|
|
27 |
|||||||||
|
|
PLAGE D’UTILISATION ET SUGGESTIONS |
41 |
|||||||||
CONSIGNES DE SÉCURITÉ IMPORTANTES POUR |
|
|
||||||||||
|
|
SÉLECTION DU COUPLE DE SERRAGE |
41 |
|||||||||
L’UTILISATION DU CHARGEUR DE BATTERIE |
29 |
|||||||||||
|
|
|
|
|
||||||||
LE SÉCURITÉ IMPORTANTES POUR |
|
|
ENTRETIEN ET INSPECTION .................................. |
42 |
||||||||
L’UTILISATION DE LA BATTERIE ET DU |
30 |
ACCESOIRES |
43 |
|||||||||
CHARGEUR DE BATTERIE |
|
|
||||||||||
|
|
ACCESSOIRES STANDARD |
43 |
|||||||||
MISE AU REBUT D’UNE BATTERIE USÉE |
31 |
|||||||||||
ACCESSOIRES EN OPTION |
44 |
|||||||||||
DESCRIPTION FONCTIONNELLE |
|
|
32 |
|||||||||
|
|
LISTE DES PIECES |
67 |
|||||||||
MODELE |
|
|
32 |
|||||||||
|
|
|
|
|
|
|
||||||
NOM DES PARTIES ............................................ |
|
|
32 |
|
|
|
|
|
||||
SPECIFICATIONS ................................................ |
|
|
34 |
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
ÍNDICE |
|
|
|
|
||
Español |
|
|
|
|
|
|
|
|||||
|
|
Página |
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|||
INFORMACIÓN IMPORTANTE SOBRE |
|
SEGURIDAD ................................................. |
45 |
SIGNIFICADO DE LAS PALABRAS DE |
|
SEÑALIZACIÓN ............................................ |
45 |
SEGURIDAD ............................................................. |
46 |
NORMAS GENERALES DE SEGURIDAD – PARA |
|
TODAS LAS HERRAMIENTAS |
|
ALIMENTADAS CON BATERÍA ................... |
46 |
NORMAS Y SÍMBOLOS ESPECÍFICOS DE |
|
SEGURIDAD ................................................. |
48 |
INSTRUCCIONES IMPORTANTES DE SEGURIDAD |
|
PARA EL CARGADOR DE BATERÍAS .......... |
50 |
INSTRUCCIONES IMPORTANTES DE |
|
SEGURIDAD PARA LA BATERÍA Y EL |
|
CARGADOR DE BATERÍAS ......................... |
51 |
ELIMINACIÓN LAS BATERÍAS AGOTADAS ..... |
52 |
DESCRIPCIÓN FUNCIONAL .................................... |
53 |
MODELO .............................................................. |
53 |
NOMENCLATURA ............................................... |
53 |
ESPECIFICACIONES ............................................ |
55 |
|
Página |
MONTAJE Y OPERACIÓN ...................................... |
56 |
APLICACIONES ................................................... |
56 |
MÉTODO DE EXTRACCIÓN E INSTALACIÓN |
|
DE LA BATERÍA ............................................ |
56 |
MÉTODO DE CARGA .......................................... |
56 |
ANTES DE LA UTILIZACIÓN .............................. |
58 |
OPERACIÓN ........................................................ |
59 |
ALCANCE Y SUGERENCIAS PARA LA |
|
UTILIZACIÓN ................................................ |
62 |
FORMA DE SELECCIONAR EL PAR DE |
|
APRIETE ........................................................ |
62 |
MANTENIMIENTO E INSPECCIÓN ........................ |
64 |
ACCESORIOS ........................................................... |
65 |
ACCESORIOS ESTÁNDAR ................................. |
65 |
ACCESORIOS OPCIONALES .............................. |
66 |
LISTA DE PIEZAS .................................................... |
67 |
English
IMPORTANT SAFETY INFORMATION
Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or maintaining this power tool.
Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs, and by observing appropriate safety procedures.
Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which contain the operation and maintenance instructions.
Hazards that must be avoided to prevent bodily injury or machine damage are identified by WARNINGS on the power tool and in this Instruction Manual.
NEVER use this power tool in a manner that has not been specifically recommended by HITACHI.
MEANINGS OF SIGNAL WORDS
WARNING indicates a potentially hazardous situation which, if ignored, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury, or may cause machine damage.
NOTE emphasizes essential information.
3
English
SAFETY
GENERAL SAFETY RULES – FOR ALL BATTERY OPERATED TOOLS
WARNING: Read and understand all instructions.
Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
1.Work Area
(1)Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
(2)Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust of fumes.
(3)Keep bystanders children, and visitors away while operating a power tool.
Distractions can cause you to lose control.
2.Electrical Safety
(1)A battery operated tool with integral batteries or a separate battery pack must be recharged only with the specified charger for the battery.
A charger that may be suitable for one type of battery may create a risk of fire when used with another battery.
(2)Use battery operated tool only with specifically designed battery pack.
Use of any other batteries may create a risk of fire.
3.Personal Safety
(1)Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
(2)Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
(3)Avoid accidental starting. Be sure switch is off position before inserting battery.
Carrying tools with your finger on the switch or inserting the battery pack into a tool that have the switch on invites accidents.
(4)Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.
(5)Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enable better control of the tool in unexpected situations.
(6)Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.
4
English
4.Tool Use and Care
(1)Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.
(2)Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.
(3)Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired.
(4)Disconnect battery pack from tool or place the switch in the locked or off position before making any adjustments, changing accessories, or storing the tools. Such preventive safety measures reduce the risk of starting the tool accidentally.
(5)Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.
(6)When battery pack is not in use, keep it away from other metal objects like: paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another.
Shorting the battery terminals together may cause sparks, burns, or a fire.
(7)Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control.
(8)Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation. If damaged, have the tool serviced by a HITACHI authorized service center before using. Many accidents are caused by poorly maintained tools.
(9)Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may create a risk of injury when used on another tool.
5.Service
(1)Tool service must be performed only by a HITACHI authorized service center. Service or maintenance performed by unqualified personnel could result in a risk of injury.
(2)When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instruction may create a risk of electric shock or injury.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
●Lead from lead-based paints,
●Crystalline silica from bricks and cement and other masonry products, and
●Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
5
English
SPECIFIC SAFETY RULES AND SYMBOLS
1.Hold tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator.
2.ALWAYS wear ear plugs when using the tool for extended periods.
Prolonged exposure to high intensity noise can cause hearing loss.
3.NEVER place hands or other body parts near the drill bit or chuck during operation. Hold the drill by its handle only.
4.Because the cordless driver drill operates by battery power, be aware of the fact that it can begin to operate at any time.
5.When working at elevated locations, clear the area of all other people and be aware of conditions below you.
6.NEVER touch moving parts.
NEVER place your hands, fingers or other body parts near the tool’s moving parts.
7.NEVER operate without all guards in place.
NEVER operate this tool without all guards or safety features in place and in proper working order. If maintenance or servicing requires the removal of a guard or safety feature, be sure to replace the guard or safety feature before resuming operation of the tool.
8.Use right tool.
Don’t force small tool or attachment to do the job of a heavy-duty tool.
Don’t use tool for purpose not intended —for example— don’t use circular saw for cutting tree limbs or logs.
9.NEVER use a power tool for applications other than those specified.
NEVER use a power tool for applications other than those specified in the Instruction
Manual.
10.Handle tool correctly.
Operate the tool according to the instructions provided herein. Do not drop or throw the tool. NEVER allow the tool to be operated by children, individuals unfamiliar with its operation or unauthorized personnel.
11.Keep all screws, bolts and covers tightly in place.
Keep all screws, bolts, and plates tightly mounted. Check their condition periodically.
12.Do not use power tools if the plastic housing or handle is cracked.
Cracks in the tool’s housing or handle can lead to electric shock. Such tools should not be used until repaired.
13.Blades and accessories must be securely mounted to the tool.
Prevent potential injuries to youself or others. Blades, cutting implements and accessories which have been mounted to the tool should be secure and tight.
6
English
14.NEVER use a tool which is defective or operating abnormally.
If the tool appears to be operating unusually, making strange noises, or otherwise appears defective, stop using it immediately and arrange for repairs by a Hitachi authorized service center.
15.Carefully handle power tools.
Should a power tool be dropped or struck against hard materials inadvertently, it may be deformed, cracked, or damaged.
16.Do not wipe plastic parts with solvent.
Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol may damage and crack plastic parts. Do not wipe them with such solvents.
Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry thoroughly.
17.ALWAYS wear eye protection that meets the requirement of the latest revision of ANSI
Standard Z87.1.
18. Definitions for symbols used on this tool. V ............ volts
— ........... |
direct current |
--- |
|
no |
.......... no load speed |
---/min ... revolutions per minute
7
English
IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGER
1.This manual contains important safety and operating instructions for battery charger Model UC9SD, UC12SD and UC14SD.
2.Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.
3.To reduce risk of injury, charge HITACHI rechargeable battery type EB912S and EB914 for UC9SD, EB1212S and EB1214L for UC12SD and EB1412S and EB1414 for UC14SD. Other type of batteries may burst causing personal injury and damage.
4.Do not expose battery charger to rain or snow.
5.Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons.
6.To reduce risk of damage to electric plug and cord, pull by plug when disconnecting battery charger.
7.Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.
8.An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock.
If extension cord must be used make sure:
a.That blades of extension cord are the same number, size, and shape as those of plug on battery charger:
b.That extension cord is properly wired and in good electrical condition; and
c.That wire size is large enough for AC ampere rating of battery charger as specified in Table 1.
Table 1
RECOMMENDED MINIMUM AWG SIZE FOR
EXTENSION CORDS FOR BATTERY CHARGERS
AC Input Rating Amperes* |
|
|
AWG Size of Cord |
|
||
|
|
|
||||
Equal to or |
but less |
|
Length of Cord, Feet (Meter) |
|||
|
||||||
greater than |
than |
25 (7.5) |
50 (15) |
100 (30) |
150 (45) |
|
0 |
2 |
18 |
18 |
18 |
16 |
|
2 |
3 |
18 |
18 |
16 |
14 |
|
3 |
4 |
18 |
18 |
16 |
14 |
|
*If the input rating of a battery charger is given in watts rather than in amperes, the corresponding ampere rating is to be determined by dividing the wattage rating by the voltage rating–for example:
1250watts
125 volts = 10 amperes
9. Do not operate battery charger with damaged cord or plug-replace them immediately.
8
English
10.Do not operate battery charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman.
11.Do not disassemble battery charger; take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.
12.To reduce risk of electric shock, unplug charger from receptacle before attempting any maintenance or cleaning. Removing the battery will not reduce this risk.
IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE BATTERY AND BATTERY CHARGER
You must charge the battery before you can use the cordless driver drill. Before using the model UC9SD, UC12SD or UC14SD battery charger, be sure to read all instructions and cautionary statements on it, the battery and in this manual.
REMEMBER: USE ONLY HITACHI BATTERY TYPES EB912S AND EB914 FOR UC9SD, EB1212S AND EB1214L FOR UC12SD AND EB1412S AND EB1414 FOR UC14SD. OTHER TYPES OF BATTERIES MAY BURST AND CAUSE INJURY!
Follow these instructions to avoid the risk of injury:
WARNING: Improper use of the battery or battery charger can lead to serious injury. To avoid these injuries:
1.NEVER disassemble the battery.
2.NEVER incinerate the battery, even if it is damaged or is completely worn out. The
battery can explode in a fire.
3.NEVER short-circuit the battery.
4.NEVER insert any objects into the battery charger’s air vents. Electric shock or
damage to the battery charger may result.
5. NEVER charge outdoors. Keep the battery away from direct sunlight and use only where there is low humidity and good ventilation.
6.NEVER charge when the temperature is below 50°F (10°C) or above 104°F (40°C).
7.NEVER connect two battery chargers together.
8.NEVER insert foreign objects into the hole for the battery or the battery charger.
9.NEVER use a booster transformer when charging.
10.NEVER use an engine generator or DC power to charge.
11.NEVER store the battery or battery charger in places where the temperature may
reach or exceed 104°F (40°C).
12. ALWAYS operate charger on standard household electrical power (120 volts). Using the charger on any other voltage may overheat and damage the charger.
13.ALWAYS wait at least 15 minutes between charges to avoid overheating the charger.
14.ALWAYS disconnect the power cord from its receptacle when the charger is not in use.
9
English
DISPOSAL OF THE EXHAUSTED BATTERY
WARNING: Do not dispose of the exhausted battery. The battery must explode if it is incinerated. The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of it’s useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.
SAVE THESE INSTRUCTIONS
AND
MAKE THEM AVAILABLE TO
OTHER USERS
AND
OWNERS OF THIS TOOL!
10
English
FUNCTIONAL DESCRIPTION
NOTE:
The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool.
NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safety instructions contained in this manual.
Some illustrations in this Instruction Manual may show details or attachments that differ from those on your own power tool.
MODEL
DS9DVF: with charger (UC9SD) and case
DS12DVF: with charger (UC12SD) and case
DS14DVF: with charger (UC14SD) and case
NAME OF PARTS
1.Cordless Driver Drill
<DS9DVF and DS12DVF>
Keyless Chuck
|
Shift Knob |
|
|
|
|
Housing |
|
|
|
Cap |
|
Bit |
|
|
Push |
|
|
||
L Indication |
Nameplate |
R Indication |
||
Button |
||||
|
|
|||
Switch Trigger |
|
|
|
|
Handle |
|
|
|
|
<DS14DVF> |
Battery |
|
|
|
|
|
|
||
Keyless Chuck |
Shift Knob |
|
|
|
|
|
|
||
|
Housing |
|
||
Cap |
|
Bit |
|
|
Push |
Nameplate |
R Indication |
||
L Indication |
||||
Switch Trigger |
Button |
|
|
|
Handle 
Battery
11
English
Battery |
|
|
<EB912S or EB914> |
<EB1212S or EB1214L> |
<EB1412S or EB1414> |
Terminal Hole |
Terminal Hole |
Terminal |
|
|
|
|
|
Hole |
|
|
Nameplate |
Latch |
|
Latch |
Nameplate |
Latch |
|
Nameplate |
|
|
|
|
Fig. 1 |
2. Battery Charger (UC9SD, UC12SD and UC14SD)
|
Air vent |
|
|
|
Battery Installation Hole |
Cord |
|
|
|
|
Pilot Lamp |
Plug |
Name |
Caution Plate |
|
Plate |
|
|
|
|
Fig. 2
12
|
|
|
|
|
|
|
English |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SPECIFICATIONS |
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
1. Cordless Driver Drill |
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
Model |
|
|
|
DS9DVF |
DS12DVF |
|
DS14DVF |
|
|
|
|
|
|
|
|
|
|
Motor |
|
|
|
|
DC motor |
|
|
|
|
|
|
|
|
|
|
||
No-load speed |
Low |
0–280/min |
0–350/min |
|
0–400/min |
|
||
|
|
|
|
|
|
|
|
|
|
|
High |
0–840/min |
0–1050/min |
|
0–1200/min |
|
|
|
|
|
|
|
|
|
|
|
Capacity |
Drilling |
Wood |
23/32"(18mm) |
13/16"(21mm) |
|
1"(25mm) |
|
|
|
|
|
(Thickness |
(Soft Wood) |
(Soft Wood) |
(Soft Wood) |
|
|
|
|
11/16" |
|
|
|
|
|
|
|
|
(18mm)) |
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
Metal |
3/8" (10mm) |
15/32" (12mm) |
15/32" (12mm) |
|
||
|
|
(Thickness |
(Mild Steel) |
(Mild Steel) |
|
(Mild Steel) |
|
|
|
|
1/16" |
|
|
|
|
|
|
|
|
15/32" (12mm) |
19/32" (15mm) |
19/32" (15mm) |
|
|||
|
|
(1.6mm)) |
|
|||||
|
|
(Aluminum) |
(Aluminum) |
(Aluminum) |
|
|||
|
|
|
|
|
||||
|
|
|
|
|
|
|
||
|
Screw |
Wood screw |
#12 × 1-25/32" |
#12 × 2-1/2" |
#12 × 2-1/2" |
|
||
|
Driver |
|
|
(5.5mm × 45mm) |
(5.5mm × 63mm) |
(5.5mm × 63mm) |
|
|
|
|
Small screw |
1/4"(6mm) |
1/4"(6mm) |
|
1/4"(6mm) |
|
|
Drill chuck capacity |
|
|
Maximum gripping diameter 3/8" (10mm) |
|
||||
|
|
|
|
|
|
|
|
|
Battery |
Model |
|
|
EB912S/EB914 |
EB1212S/EB1214L |
EB1412S/EB1414 |
|
|
|
|
|
|
|
|
|
|
|
|
Type |
|
|
Nickel cadmium battery |
|
|||
|
|
|
|
|
|
|
|
|
|
Voltage |
|
|
DC 9.6V |
DC 12V |
|
DC 14.4V |
|
|
|
|
|
|
|
|
|
|
|
Charging & discharging |
|
about 300 |
|
|
|
||
|
frequency |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Weight |
|
|
|
3.2 lbs. (1.5 kg) |
3.4 lbs. (1.6 kg) |
3.8 lbs. (1.7 kg) |
|
|
|
|
|
|
|
|
|
|
|
2. Battery Charger |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Model |
|
|
|
UC9SD |
UC12SD |
|
UC14SD |
|
|
|
|
|
|
|
|
||
Input power source |
|
|
Single phase: AC120V 60Hz |
|
||||
|
|
|
|
|
||||
Charging time |
|
|
Approx. 60min. (At a temperature of 68°F (20°C) |
|
||||
|
|
|
|
|
|
|
|
|
Charging voltage |
|
|
DC 9.6V |
DC 12V |
|
DC 14.4V |
|
|
|
|
|
|
|
|
|
|
|
Charging current |
|
|
DC 1.55A |
DC 1.55A |
|
DC 1.55A |
|
|
|
|
|
|
|
|
|
|
|
Weight |
|
|
|
2.6 lbs. (1.2kg) |
3.3 lbs. (1.5kg) |
3.5 lbs. (1.6kg) |
|
|
|
|
|
|
|
|
|
|
|
13
English
ASSEMBLY AND OPERATION
APPLICATIONS
Use as a drill
Drilling of soft steel, wood, plastic and aluminum materials.
Use as a screwdriver
Tightening and loosening of machine screws, wood screws and tapping screws.
REMOVAL AND INSTALLATION METHOD OF BATTERY
How to install the battery.
Align the battery with the groove in tool handle and slip it into place.
Always insert it all the way until it locks in place with a little click, If not, it may accidentally fall out of the tool, causing injury to you or someone around you. (Fig. 3)
How to remove the battery.
Withdraw battery from the tool handle while pressing the latch (1 pc. or 2 pcs) of the battery. (Fig. 3)
<DS9DVF and DS12DVF> |
<DS14DVF> |
|
Handle |
Handle |
|
|
|
|
Latch |
Insert |
|
Insert |
|
|
|
|
|
Push |
Pull out |
Latch |
Pull out |
|
|
|
Push |
|
Battery |
|
|
|
Battery |
|
|
Fig. 3 |
|
|
|
CHARGING METHOD
NOTE: Before plugging into the receptacle, make sure the following points.
The power source voltage is stated on the nameplate.
The cord is not damaged.
WARNING: Do not charge at voltage higher than indicated on the nameplate.
If charged at voltage higher than indicated on the nameplate, the charger will burn up.
14
English
1.Insert the battery to the battery charger.
Insert the battery into the battery charger as shown in Fig. 4. Make sure it contacts the bottom of the battery charger.
<DS9DVF and DS12DVF> |
<DS14DVF> |
Battery
Pilot Lamp
Fig. 4
2. Insert the plug of battery charger into the receptacle.
WARNING: Do not use the electrical cord if damaged. Have it repaired immediately.
3.Charging
When the plug of battery charger has been inserted into the receptacle, charging will commence and the pilot lamp will light on.
NOTE: If the pilot lamp dose not light, pull out the plug from the receptacle and check if the battery is properly mounted.
In approx. one hour, when the battery is fully charged, the pilot lamp will go out.
NOTE: The battery charging time becomes longer when a temperature is low or the voltage of the power source is too low.
When the pilot lamp does not go off even if more than four hour has passed after start of the charging, stop the charging and contact your HITACHI AUTHORIZED SERVICE CENTER.
4.Disconnect battery charger from the receptacle.
15
English
CAUTION:
Do not pull the plug out of the receptacle by pulling on the cord.
Make sure to grasp the plug when removing from receptacle to avoid damaging cord.
5.Remove the battery from the battery charger.
Supporting the battery charger with hand, pull out the battery from the battery charger.
CAUTION:
●When the battery charger has been continuosly used, the battery charger will be heated, thus constituting the cause of the failures. Once the charging has been completed, wait 15 minutes rest until the next charging.
●If the battery is rechraged when it is warm due to battery use or exposure to sunlight, the pilot lamp may not light.
The battery will not be recharged. In such a case, let the battery cool before charging.
Regarding electric discharge in case of new batteries, etc.
As the internal chemical substance of new batteries and batteries that have not been used for an extended period is not activated, the electric discharge might be low when using them the first and second time. This is a temporary phenomenon, and normal time required for recharging will be restored by recharging the batteries 2 – 3 times.
How to make the batteries perform longer.
(1)Recharge the batteries before they become completely exhausted.
When you feel that the power of the tool becomes weaker, stop using the tool and recharge its battery. If you continue to use the tool and exhaust the electric current, the battery may be damaged and its life will become shorter.
(2)Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after use. If such a battery is recharged immediately after use, its internal chemical substance will deteriorate, and the battery life will be shortened. Leave the battery and recharge it after it has cooled for a while.
BEFORE USE
Check the work area to make sure that it is clear of debris and clutter.
Clear the area of unnecessary personnel. Ensure that lighting and ventilation is adequate.
16
English
OPERATION
1. Mounting and dismounting of the bit
Tighten
Ring Sleeve
Fig. 5
(1)Mounting the bit.
Insert a screwdriver bit etc. into the keyless drill chuck. Firmly grasp the ring and tighten the sleeve by turning it
toward the right (in the clockwise direction as viewed from the front). (See Fig.5)
NOTE: If the sleeve becomes loose during operation, tighten it further.
The tightening force becomes stronger when the sleeve is tightened.
(2)Dismounting the bit.
Firmly grasp the ring and loosen the sleeve by turning it toward the left (in the counterclockwise direction as viewed from the front). (See Fig.5)
CAUTION:
When mounting a bit into the keyless chuck, tighten firmly. If the sleeve is not tight, the bit may slip or fall out, causing injury.
NOTE: Loosening stuck or hard to move sleeves.
Grasp the bit installed in the keyless chuck, in a vise or similar tool.
Set the cap position to “1-11” and turn on the switch. The motor then starts. Finally, rotate the sleeve to the left, and it will loosen.
2.Confirm that the battery is mounted correctly.
3.Check the rotational direction
Triger switch
R marks 
L marks
R 
L
Selector
Button
Fig. 6
The bit rotates clockwise (viewed from the rear side) by pushing the R-side of the selector button.
The L-side of the selector button is pushed to turn the bit counterclockwise. (See Fig. 6). (The L and R marks are provided on the body.)
When the trigger switch is depressed, the tool rotates. When the trigger is released, the tool stops.
The rotational speed of the drill can be controlled by varying the amount that the trigger switch is pulled. Speed is low when the trigger switch is pulled slightly and increases as the trigger switch is pulled more.
When releasing the trigger of the switch, the brake will be applied for immediate stopping.
17
English
4. Change rotation speed
speed |
Low speed |
Shift knob |
Shift knob |
Fig. 7 |
Fig. 8 |
Operate the shift knob to change the rotational speed. Move the shift knob in the direction of the arrow (see Figs. 7 and 8).
When the shift knob is set to “LOW”, the drill rotates at a low speed. When set to “HIGH”, the drill rotates at a high speed.
CAUTION:
●When changing the rotational speed with the shift knob, confirm that the switch is off. Changing the speed while the motor is rotating will damage the gears.
●When a large force is required for operation (operations indicated in the following chart) set the shift knob to “LOW”. If “HIGH” is set and the unit is used, it may cause the motor to burn out or malfunction prematurely.
Table 2
Model |
DS9DVF |
DS12DVF / DS14DVF |
|
|
|
Metal Drilling |
When the diameter of the hole |
When the diameter of the hole |
|
exceeds 3/16"(5mm). |
exceeds 1/4"(6.5mm). |
|
|
|
Wood Drilling |
When the diameter of the hole |
When the diameter of the hole |
|
exceeds 15/32"(12mm). |
exceeds 15/32"(12mm). |
|
|
|
Wood Screw |
When the size of the wood |
When the size of the wood |
Tightening |
screw exceeds 5/32"(3.8mm) |
screw exceeds 5/32"(3.8mm) |
|
diameter × 1-1/4"(32mm). |
diameter × 1-31/32"(50mm). |
5. Confirm the cap position (see Fig. 9)
CapTriangle mark
mark (1)
Weak
Strong |
(2) |
|
Fig. 9 |
The tightening torque of this unit can be adjusted according to the cap position, at which the cap is set. When using this unit as a screwdriver, line up the one of the numbers “1, 3, 5 ... 22” on the cap, or the black dot, with the triangle mark on the outer body.
When using this unit as a drill, line up the cap drill mark “
” with the triangle mark on the outer body.
18
English
mark |
CAUTION: |
|
The cap cannot be set between the numbers “1, 3, 5 ... 22” |
|
or the black dot. |
|
Do not use with the cap set at the black line between the |
|
number “22” and the drill mark “ ”. Doing so may |
Black line |
cause damage. (See Fig. 10) |
|
|
Fig. 10 |
|
6. Tightening torque adjustment
(1)Tightening torque
Tightening torque should correspond in its intensity to the screw diameter. When too strong power is used, the screw head may be broken or be injured.
Be sure to adjust the cap position according to the screw diameter.
(2)Tightening torque indication (See Fig. 9)
The tightening torque differs depending on the type of screw and the material being tightened.
The unit indicates the tightening torque with the numbers “1, 3, 5 ... 22” on the cap, and a black dot. The tightening torque at position “1” is the weakest and the torque is strongest at the highest number.
(3)Adjusting the tightening torque (See Fig. 9)
Rotate the cap and line up the numbers “1, 3, 5, ... 22” on the cap, or the black dot, with the triangle mark on the outer body. Adjust the cap in the weak or the strong torque direction according to the torque you need.
CAUTION:
The motor rotation may be locked to cease while the unit is used as drill. While operating the driver drill, take care not to lock the motor.
When setting the shift knob to “HIGH” (high speed) and the position of the cap is “17” to “22”, it may happen that the clutch does not engaged and that the motor is locked. In such a case, please set the shift knob to “LOW” (low speed).
If the motor is locked, immediately turn the power off. If the motor is locked for a while, the motor or battery may be burnt.
Too long hammering may cause the screw broken due to excessive tightening.
A buzzing noise is produced when the motor is about to rotate; This is only a noise, not a machine failure.
19
English
THE SCOPE AND SUGGESTIONS FOR USES
Table 3
|
Work |
Cap position |
|
Suggestions |
|
|
|
|
|
|
|
|
|
Wood |
|
|
|
|
|
|
|
|
|
Drilling |
|
Steel |
|
Use for drilling purpose. |
|
|
|
|
|
|
|
|
|
Aluminum |
|
|
|
|
|
|
|
|
|
|
|
Machine |
1 – 22 |
Use the bit and socket matching the screw |
|
Screw |
|
screw |
diameter. |
||
|
|
||||
|
|
|
|
|
|
tightening |
|
Wood |
1 – |
Use after drilling a pilot hole. |
|
|
|
screw |
|||
|
|
|
|
|
|
|
|
|
|
|
|
HOW TO SELECT TIGHTENING TORQUE
Table 4
Cap |
Tightening torque |
Operation example |
|
position |
|||
|
|
||
|
|
|
|
1 |
Approximately 9 in-lbs. (10 kg-cm) |
|
|
|
|
Machine screw tightening |
|
3 |
Approximately 15 in-lbs. (17 kg-cm) |
||
Screw tightening for soft |
|||
|
|
||
7 |
Approximately 23 in-lbs. (26 kg-cm) |
||
wood material |
|||
13 |
Approximately 35 in-lbs. (40 kg-cm) |
|
|
|
|
|
|
17 |
Approximately 43 in-lbs. (49 kg-cm) |
Screw tightening for hard |
|
22 |
Approximately 52 in-lbs. (60kg-cm) |
wood material |
|
|
|
|
|
|
High speed: approximately 5 in-lbs. |
|
|
|
(60 kg-cm)(DS9DVF) |
|
|
|
approximately 61 in-lbs. |
|
|
|
(70 kg-cm)(DS12DVF) |
|
|
|
approximately 70 in-lbs. |
|
|
|
(80 kg-cm)(DS14DVF) |
Thick screw tightening |
|
|
Low speed: approximately 156 in-lbs. |
When used as a drill. |
|
|
(180 kg-cm)(DS9DVF) |
|
|
|
approximately 191 in-lbs. |
|
|
|
(220 kg-cm)(DS12DVF) |
|
|
|
approximately 213 in-lbs. |
|
|
|
(245 kg-cm)(DS14DVF) |
|
NOTE:
The selected content shown in Table 4 indicates the differences according to screw type, screw size and material used.
CAUTION:
●While operating the Cordless driver drill, take care not to lock the motor. If the motor is locked, immediately turn the power off.
If the motor is locked for a while, the motor or battery will be burnt.
●Do not tighten too strongly as the screw heads will be damaged.
20
English
MAINTENANCE AND INSPECTION
CAUTION: Pull out battery before doing any inspection or maintenance.
1.Checking the condition of the bit.
The bits should be checked regularly. If worn or broken bits can slip or decrease the efficiency of the motor and burn it out.
Replace worn bits with new ones.
CAUTION: If you use a driver bit of which point is worn or broken, it will be dangerous since it slips. So replace it with a new one.
2.Check the Screws
Loose screws are dangerous. Regularly inspect them and make sure they are tight.
CAUTION: Using this power tool with loosened, screws is extremely dangerous.
3.Check for Dust
Dust may be removed with a soft cloth or a cloth dampened with soapy water.
Do not use bleach, chlorine, gasoline or thinner, for they may damage the plastics.
4.Storage
Storing in a place below 104°F (40°C) and out of the reach of children.
5.Service and repairs
All quality power tools will eventually require servicing or replacement of parts because of wear from normal use. To assure that only authorized replacement parts will be used, all service and repairs must be performed by a HITACHI AUTHORIZED SERVICE CENTER, ONLY.
6.Service parts list
CAUTION: Repair, modification and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center.
This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed.
MODIFICATIONS:
Hitachi Power Tools are constantly being improved and modified to incorporate the latest technological advancements.
Accordingly, some parts (i.e. code numbers and/or design) may be changed without prior notice.
21
English
ACCESSORIES
WARNING: ALWAYS use Only authorized HITACHI replacement parts and accessories. NEVER use replacement parts or accessories which are not intended for use with this tool. Contact HITACHI if you are not sure whether it is safe to use a particular replacement part or accessory with your tool.
The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage.
NOTE:
Accessories are subject to change without any obligation on the part of the HITACHI.
STANDARD ACCESSORIES
1 
2 3
4
DS9DVF
1 |
Phillips bit (No. 2 × 55L)(Code No. 318236) ....... |
1 |
||
2 |
Battery (EB912S or EB914) .................................. |
|
2 |
|
3 |
Battery Charger (UC9SD) .................................... |
|
1 |
|
4 |
Plastic Case (Code No. 319967) .......................... |
|
1 |
|
|
1 |
2 |
3 |
|
4
DS12DVF
1 |
Phillips bit (No. 2 × 55L)(Code No. 318236) ....... |
1 |
||
2 |
Battery (EB1212S or EB1214L) ............................ |
|
2 |
|
3 |
Battery Charger (UC12SD) .................................. |
|
1 |
|
4 |
Plastic Case (Code No. 319967) .......................... |
|
1 |
|
|
1 |
2 |
3 |
|
4
DS14DVF
1 |
Phillips bit (No. 2 × 55L)(Code No. 318236) ....... |
1 |
2 |
Battery (EB1412S or EB1414) .............................. |
2 |
3 |
Battery Charger (UC14SD) .................................. |
1 |
4 |
Plastic Case (Code No. 320653) .......................... |
1 |
22
Loading...